Annual Maintenance works for Buildings in wharf area inside Green Gate at VOC Port Authority on Unit Rate Basis

Earthwork excavation in trenches for foundation in sand and other loose soils not exceeding 1.50m in width and including dressing of sides and ramming of bottom lift upto 1.50m including getting out of the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m and lift of 1.50m, cost including shuttering, strutting, bailing out seepage ofwater wherever necessary etc.,complete complying with AISS and as directed by the departmental officers.

Fabricating and placing in position of M.S / Tor steel grills for R.C.C works in all floors including cost of Steel, cutting, bending, binding with 16 Gauge GI Binding wire and placing in position etc., complete complying with AISS and as directed by the departmental officers.

Providing Form work including centring, shuttering, (shuttering Planks shall not less than 38 mm thick) so as to give a rough finish shuttering and propping etc., in all floors upto full height of the building and removal of the same for in situ RCC work such as beam, slabs, lintels, sunshade etc., complete complying with AISS and as directed by the departmental officers.

Brick work in Cement Mortar 1:5 (One cement, five sand) using chamber burnt bricks for walls in allfloors up to floor two level of the building including cost of all materials, labour, curing etc., complete complying with AISS and as directed by the departmental officers.

Providing and fixing of glazed Aluminium Partition with Aluminium frame section (manufactured to relevant IS Specification) for vertical and bottom of size 65 X 38 X 2 mm, horizontal section of size 100 X 45 X 2 mm including providing 5.5 mm thick glasssuperior quality at middle portion and Novapan of 8 mm thick at top and bottom with necessary accessories like snap on beading (clips), cleat angles, fully threaded 75mm long metal screws, wooden plugs & metal screws etc., including drilling holes in theconcrete / brick masonry etc., wherever required, all as directed at site of work including all materials, labour, tools, equipments, scaffolding, transport, fuel, etc., complete. Note:Aluminium sections shall be smooth, rust free, straight, mitered andjointed mechanically wherever required including using glazing clip, rubber beading for glazing and necessary screws, plugs etc., complete and as directed by the departmental officers.

Providing and laying approved colour and quality of Ceramic floor tiles 30 x 30 cm in Cement Mortar 1:3, 20 mm thick. The rate inclusive of cost of tiles, all materials, labour, white cement, conveyance etc., complete complying with AISS and as directed by the departmental officers

Providing and fixing CM 1:3, 6 mm thick of 30 x 30 cm wall tiles over the existing wall up to 2.50 m height by chipping the wall surfaces wherever required and fixing with approved colour and quality of tiles including all materials, labour,equipments etc., complete complying with AISS and as directed by the departmental officers.

Providing and fixing A.C sheet roofing with AC corrugated sheet 6mm thick for roof trusses of shed and shade including cost of sheet, conveyance, fixing the sheet with necessary clamps / screws and labour charges for fixing sheet etc., complete complying with AISS and as directed by the departmental officers.

Providing and fixing A.C sheet ridges with G.I. J or L bolts including cost of ridges, conveyance, fixing the ridges with necessary clamps / screws and labour charges for fixing ridges etc., complete complying with AISS and as directed by the departmental officers

Plastering the Brick work 15 mm thick in Cement Mortar 1:5 (One cement, five sand) for all faces of walls (even and uneven) in all floors upto full height of the building including necessary scaffolding, racking of masonry joints, cleaning, curing etc.,complete complying with AISS and as directed by the departmental officers.

Painting ONE coat with Plastic emulsion of approved brand over OLD wall surfaces to give an even shade, after thoroughly brushing the surface clean of all grease, dirt, loose pieces of scales and also including preparing the surface even and sand paperes smooth including all materials, labour, brushes, scaffolding, etc., complete complying with AISS and as directed

Applying One coat of Alkali Resistant Primer and One coat of ACE - Exterior Emulsion Paint of approved colour and quality over the existing wall surface in all floors to give an even shade after thoroughly brushing the surface clean of all grease, dirt,loose pieces of scales and also including preparing the surface even and sand paperes smooth including all materials, labour, brushes, scaffolding, etc., complete complying with AISS and as directed by the departmental officers.

Applying one coat of Alkali Resistant Primer and One coat of APEX - Exterior Emulsion Paint of approved colour and quality over the existing wall surface in all floors to give an even shade after thoroughly brushing the surface clean of all grease, dirt, loose pieces of scales and also including preparing the surface even and sand paperes smooth including all materials, labour, brushes, scaffolding, etc., complete complying with AISS and as directed by the departmental officers.

Painting the steel surfaces with One coat of Synthetic enamal paint of approved quality (excluding priming coat) on new steel and other metal surfaces with enamel paint, brushing, interior to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including all materials, labour, brushes, etc., complete complying with AISS and as directed by the departmental officers.

Dismantling and removal of Reinforced Cement Concrete (RCC) above G.L. upto floor two level including stacking of serviceablematerials and disposal of unserviceable materials within a lead of 100 m including all labour, tools, equipments, transport, fuel, etc., complete complying with AISS and as directed by the departmental officers.

Dismantling Asbestos Cement Sheet roofing (AC Sheet) incliding ridges, hips, velleys, gutters, etc., and stacking the serviceable materials and dispostal of unserviceable materials within a lead of 100 m including all labour, tools, equipments, transport, fuel, etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing 15mm dia. PVC pipe 10 kg. per cm2 working pressure in wall, ceiling and floor with necessary clamps and screws, making holes in the wall wherever necessary by drilling holes in the roofs and walls, packed the holes with necessary brick works or concrete wherever necessary plastering the surface smooth with required scaffolding including cost of pipe and special such as elbows, tee, union joints, reducer etc., cutting threading etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing 20mm dia. PVC pipe 10 kg. per cm2 working pressure in wall, ceiling and floor with necessary clamps and screws, making holes in the wall wherever necessary by drilling holes in the roofs and walls, packed the holes with necessary brick works or concrete wherever necessary plastering the surface smooth with required scaffolding including cost of pipe and special such as elbows, tee, union joints, reducer etc., cutting threading etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing in position 15mm dia. Heavy type Brass Chromium Plated Pillar tap of approved quality including all materials, labour etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing in position of best Indian make heavy duty Gun Metal Wheel Valve at 25mm dia. Of approved quality including all materials, labour etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing of 1000 litres capacity Sintex double layer water tank with approved brand includingcost of PVC water tank, making connection with input and output water pipe line and valves. Cost inclusive of all materials, labour charges, & conveyance etc., complete and as directed by the departmental officers.

Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser / Wherever required using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm diaof 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete and as directed by the departmental officers.

Supplying and fixing UPVC WINDOWS( Un-Plasticized Polyvinyl Chloride) windows of casement type (open) from the profile the size of outer frame 60mm X 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with overall the edges of frame and shutter. The shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work. The rate including cost of all materials, labour, tools & plants, conveyance, fixing in position etc., complete and as directed by the departmental officers.

Providing and fixing of 12.5 mm thick Gypsum Board False ceiling with suspended GI channels for every 2'-0 x 2'-0 c/c fixed with brass screws, etc. The surface joints to be finished with paper tape and putty etc.,. The cost including for al lthe materials, labour charges ... etc. complete and as directed by the departmental officers.

Providing and laying terrace lime concrete weathering course with grade brick aggregate 25 mm nominal size and 50% mortar comprising of 1 lime putty and 2 surkhi and curing including all materials, labour, etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing in position of Wooden panelled door single shutter including cost of hold fasts and applying one coat of wood primer of approved quality, fixing of first quality ISI standard furniture fittings with screws / bolt & nuts, the rate shall include cost of wood, labour for wrought and put up, etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing Solid Panel PVC door with frame - Supplying and fixing Solid PVC Door Shusing 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter etc., complete and as directed by the departmental officers.

Providing and fixing of Anodized Aluminium Door of various size (manufactured to relevant IS Specification) of 37.5 x 37.5mm Vertical and Door bottom rails using 67.5 x 37.5mm including providing 5.5 mm thick glass superior quality for top panel and with Novapan of 8 mm thick at bottom panel with necessary accessories like snap on beading (clips), cleat angles, fully threaded 75mm long metal screws, wooden plugs & metal screws etc., wherever required, all as directed at site of work including all materials, labour, tools, equipments, scaffolding, transport, fuel, etc., complete. Note: Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including using glazing clip, rubber beading for glazing and necessary screws, plugs etc., complete and as directed by the departmental officers.

Providing and fixing sheet glass 5.5 mm thick bedded in putty and fixed with wooden beadings including all materials, labour, putty, nails, etc., complete complying with AISS and as directed by the departmental officers.

Providing and laying approved colour and quality of Stain Free Nano Polish Vitrified floor tiles 60 x 60 cm in Cement Mortar 1:4, 20 mm thick. The rate inclusive of cost of tiles, all materials, labour, white cement, conveyance etc., complete complyingwith AISS and as directed by the departmental officers.

Dismantling and removal of Brick Masonry work (BW) in Cement Mortar above G.L. upto floor two level including stacking of serviceable materials and disposal of unserviceable materials within a lead of 100 m including all labour, tools, equipments, transport, fuel, etc., complete complying with AISS and as directed by the departmental officers.

Dismantling and removal tiled floors laid in Cement Mortar upto floor two level including stacking of serviceable materials and disposal of unserviceable materials within a lead of 100 m including all labour, tools, equipments, transport, fuel, etc., complete complying with AISS and as directed by the departmental officers.

Providing and fixing Precoated metal sheet 0.45mm for Roofing with hot dipped galvanised prepainted steel sheet for roof of make TATA or equivalent including cost of metal sheet, conveyance, fixing the sheet with necessary clamps / screws and labour charges for fixing sheet etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing Rolling shutters with ISI make of approved size and section using 18 GI sheet with Gear Operated Type (from 8 sqm. to 12 sqm. Area), M.S.laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength and M.S top cover to required thickness for rolling shtters. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc., including cost of all materials, labour charges and minor tools, all handling and transportation charges to work site etc., complete and as directed by the departmental officers.

Supplying the structural steel, MS Flats, Square Rods, Angles, Channels etc., for vertical members / bracing /stiffeners / Base plates or for any other usage as a structural member, fabricating, welding and erecting the frame work in position at the locations shown in the drawing including all labour, materials, conveyance, tools & plants, etc., complete and as directed by the departmental officers (Note : 1. While fabricating, necessary holes and bolt & nut shall be provided at no extra cost in the structural members. 2. In case, the specified MS section is not available in the market, the nearest alternative section may be used after approval of the Engineer).

Supplying and fixing in position of best Indian make chinnaware water closet of European type (White) of double trap syphonic with fibre cover including all fittings and necessary lead pipe jointing the trap with C.I. pipe, the pipe connection being embedded below floor level in brick jelly concrete in lime mortar 1:2 including cost of fittings of low level flushing cistern with syphonic fitting tank of 12.5 litre capacity with inlet and over flow at bottom and connecting it with water supply pipe line and painting the pipe line with two coats of paint approved quality including all materials, labour etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing in position of best Indian make chinaware water closet of indian style (white color) of approved quality (make parryware/Hindware) and size 580mmx440mm with foot rests (Oriya type) with necessary 'P' or 'S' trap in brick jelly concrete in lime mortar 1:2 (one lime two sand) and plastering with CM 1:3 (one cement, three sand) finshing roughly to receive floor finish including all materials, labour etc., complete complying with AISS and as directed by departmental officers.

Supplying and fixing of Lipped Mouth Porcelin Flat Urinal (White) of approved quality with all accessories such as 32mm dia bell mouth PVC connection, 15mm dia G.M wheel valve, 15mm ida 'B' class GI waste water pipe, 15mm dia nylon coneection, 15mm dia brass nipple, including all materials, labour etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing in position of chinnaware Wash Basin (White color) 550 mm x 400mm size with pedestal of approved quality with necessary fittings such as cast iron bracket, 1 no 15mm C.P heavy duty piller tap with pentagonal head, 32mm dia PVC wastewater pipe and 15mm dia nylon connection, 1 No 15 mm dia G.M. wheel valve and fixing it with the wall with necessary plugs, clamps and screws, and giving water supply connection and painting the exposed pipe connection with two coats of paint of approved colour, including all labour, materials etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing in position of 600 x 450 mm size Mirror of best make, first quality approved by the department including plywood back, plugs, screws etc., complete complying with AISS and as directed by the departmental officers.

Supplying and fixing of Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded Section Body Tubular Type Universal Hydraulic Door Closer with Double Speed Adjustment like HARDWYN (make) 'GAZEL' (or) Equivalent (with ISI Monogram) for the doors including cost of door closer, accessories, labour, tools, etc., complete and as directed by the departmental officers.

Dismantling the pressed tiles and weathering course from the roof of building including cost of labour, dismantling tools & equipments and removing the debries from the site and dumping the debries to the nearby low laying area, etc., complete and as directed by the departmental officers.

Supply of 110mm dia PVC pipes - 6 Kg.per cm2 at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers

Supply of 25mm dia PVC TEE at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Supply of 15mm dia. Ball Valve - Brass (Heavy Duty) at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Supply of 20mm dia. Ball Valve - Brass (Heavy Duty) at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Supply of 15mm dia Angle Cock - Chromium plated at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers

Supply of Cp Brass health faucet 2m length at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Supply of Nylon connection 3'(heavy) (Nut Type) at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Supply of Ewc seat cover at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Supply of Ewc Tank (flush TANK) at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Supply of CP Hose tap with long body at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officer

Supplying and fixing of Aluminium Door Stopper with Rubber Bush with required screws of various sizes of approved quality. The cost inclusive of Aluminium Door Stopper with Rubber Bush and required screws, accessories, labour charges, tools, etc., complete complying with AISS and as directed by the departmental officers.

Supply of 15mm dia GI Hex Nipple at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 50mm dia PVC pipes-6Kg.per cm2 at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 63mm dia- PVC pipes-6Kg.per cm2 at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 15mm dia PVC Coupler -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 20mm dia PVC Coupler -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 25mm dia PVC Coupler -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 32mm dia PVC Coupler - at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 50mm dia PVC Coupler -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 15mm dia PVC-Elbow -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers

Supply of 20mm dia PVC-Elbow -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 25mm dia PVC-Elbow -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 32mm dia PVC-Elbow -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 50mm dia PVC-Elbow -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 25mm dia PVC-Bend -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers

Supply of 32mm dia PVC-Bend -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 15mm dia PVC-TEE -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 20mm dia PVC-TEE -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 32mm dia PVC-TEE -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 20mm x 15mm PVC-Reducer -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 25mm x 20mm PVC-Reducer -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Supply of 32mm x 25mm PVC-Reducer -at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers.

Providing and laying Plain Cement Concrete 1:4:8 (One part of cement, 4 parts of M. Sand (Crushed Stone Sand) & 8 Parts of 40 mm nominal size metal ) for foundation using 40 mm nominal size graded metal including mixing, laying, levelling, consolidation, finishing and curing etc., complete complying with AISS and as directed by the departmental officers.

Providing and laying Reinforced Cement Concrete 1:1.5:3 (One part of cement, One and a half parts of M. Sand (Crushed Stone Sand) & Three Parts of graded stone aggregate (i.e.) 2 parts of 20mm nominal size graded metal & 1 part of 10mm nominal size graded metal) using 20 mm nominal size graded metal including mixing, laying, levelling, consolidation, finishing and curing etc., and excluding the cost of form work and reinforcement grills for all RCC works in all floors upto full height of the building etc., complete complying with AISS and as directed by the departmental officers.

Finishing the top of weathering course with one course of machine pressed tiles of size 23 cm X 23 cm X 2cm in Cement Mortar 1:3 (M.Sand (Crushed Stone Sand)) including all materials, labour, etc., complete complying with AISS and as directed by the departmental officers.

Removing and relaying the existing Paver Block with required thickness in the compacted bed of river sand over the PCC, compacting and proper inter locking of paver blocks in the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver block to the required size and pattern, finishing and sweeping extra sand etc., including all labour, tools & plants, conveyance excluding the cost of Paver Block & River sand etc., complete and as directed by the departmental officers.

Providing, Supplying and Laying of Pre-cast Cement Concrete Block of size 200mm x 100mm x 100mm for heavy drive road ways and heavy loaded truck parking area of required strength of M-40 grade made with suitable vibratory method mould, laid in requireddesign & patten at site over 50mm thick compacted bed of sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand etc., complete and as directed by the departmental officers.

Dismantling doors, windows and ventilators etc., (wood or steel) shutters including chowkhats, architraves, holdfasts and other attachments etc complete and stacking them within a lead of 100m including all labour, tools, equipments, transport, fuel, etc., complete complying with AISS and as directed by the departmental officers.

Supply of 25mm dia PVC pipes -10 kg. per cm2 at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Providing and fixing of Anodized Aluminium Window / Ventilator of various size (manufactured to relevant IS Specification) of 37.5 x 37.5mm Vertical and Window bottom rails using 67.5 x 37.5mm including providing 5.5 mm thick glass superior quality for panel with necessary accessories like snap on beading (clips), cleat angles, fully threaded 75mm long metal screws, wooden plugs & metal screws etc., wherever required, all as directed at site of work including all materials, labour, tools, equipments, scaffolding, transport, fuel, etc., complete. Note: Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including using glazing clip, rubber beading for glazing and necessary screws, plugs etc., complete and as directed by the departmental officers.

Supply of 32mm dia PVC pipes -10 kg. per cm2 at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Supply of 40mm dia PVC pipes -10 kg.per cm2 at Maintenance subdivision office including conveyance charges complete and as directed by the departmental officers.

Please Enable Macros to View BoQ information