GE(S)/M-35/2022-23

Amount

M&L for PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in base/anchorage for fixing to trusses and the like, complete all as specified and directed.

M&L for RCC M-25 Nominal mix (using 20 mm graded stone aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. Note:- (Reinforcement cut as required to facilitate demolition)

M&L for Formwork to sides and soffits of slabs, floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. including edges finished the surface rough complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius, built in CM 1:6, including demolition of existing brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick built in CM 1:4, complete all as specified and directed.

S&F 35mm thick 2nd class hardwood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F 35mm thick factory made wire guazed and skeleton shutters (1st class softwood), open rebated and prepared to receive wire cloth, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing wire cloth etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats at site, complete all as specified and directed.

S&F 150mm long extruded aluminium handle, fabricated type, anodised complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

S&F door closer hydraulically regulated, aluminium extruded section body, designation No. 1, universal type, suitable for door shutters upto 700mm in width and of weight not more than 35 kg complete all as specified and directed.

S&F "as in repair" 20mm bore mild steel drapery rod with 1.0mm thick PVC wood grain coating including brackets and knobs, fixed on windows and doors for hanging curtains, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F Box type steel windows and ventilators, comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube, factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes shall be measured and paid separately under respective items of BOQ) with steel handle and steel peg stay dovetailed or welded including 2 Nos. tower bolts of 150mm long for each leaf and 10mm square bar grills at spacing as shown on drawing, welded to FI frame work including other fittings such as hinges, handles, tarred hold fasts etc. fixed in PCC blocks including two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as shown on drawing No. CEPZ/TD-27/13 sheet 1/4 to 4/4.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 125mm x 60mm for doors / windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. including filling of concrete 1:3:6 type C-0 (12.5mm graded stone aggregate) as in back of chowkhats and including two coats of synthentic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F tubular framed steel trusses (all as per pattern of existing dismantled trusses) made out of MS medium grade tube (ERW or induction butt welded ) upto 60mm bore conforming to I. S.1161-1979 grade St.-240 quality 'A', including welding of distance pieces, cleats, special shaped washer etc. and applying two coat of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed.

S&F tubular purlins fixed independently made out of medium grade tube (ERW or induction butt welded ) upto 40mm bore conforming to I. S.1161-1979 grade St.-240 quality 'A', including welding of distance pieces, jointing plates and two coat of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed.

M&L Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (ISI marked) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick (ISI marked) of any colour having tensile strength of 550 Mpa as in ridge/valley , gutter or straight flashings etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Mild steel screw bolts with 16mm dia of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 22.5cm and n exc 30cm long complete all as specified and directed.

M&L False ceiling of 9.5mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or colour) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in position not otherwise specifically provided for, complete all as specified and directed.

M&L PCC 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates) average thickness 50mm as in roof padding finish the surface even and smoothe without using extra cement complete all as specified and directed.

M&L for 10mm thick cement plaster on roof top in cement mortar 1:4 on concrete surfaces, finished even and smooth without using extra cement including and mixing with liquid WPC @ 0.200ltr/ 50 Kg bag of cement, complete all as specified and directed.

M&L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjas / canopy / parapet wall, to be executed through approved applicator of the membrane manufactured with following specifications, complete all as specified and directed :- (a) Cleaning the top surface of RCC roofing properly with water. (b) Applying oil bound bitumen primer @ 0.30 Litre / Sqm, manufactured by the same agency as that of APP with a density 0.87-0.89 KG / Litre at 25 degree centigrade on prepared surface. (c) Laying of membrane not less than 3.0mm thick APP modified water proofing membrane weighing not less than 3.60 KG/Sqm reinforced with non woven polyster fiber weight not less than 160 Gms/Sqm using butane torch by torch application with 10cm overlap and 15cm end lap. (d) Top of membrane shall be provided with solar reflective bituminous aluminum paint @ 0.10 KG / Sqm as prescribed by manufacturer of membrane. (e) APP Membrane shall be stick inside parapet where available by chase cutting and sealed with PCC 1:2:4, type B-0. (f) Top of membrane shall be provided with solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

M&L for 75 mm thick plain cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floors, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving, laid in slope, finished even and fair including making joints at every 2.5 mtr and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight, complete all as specified and directed.

M&L for coloured machine pressed precast rubber moulded concrete interlocking (Grey/red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, laid dry over and including 50 mm thick screened river washed sand cushion, and dismantling existing interlocking paver block of any shape and size removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for ceramic coloured rectified edges tiles 7 to 8mm thick, area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in floors etc, set and jointed in neat cement slurry and pointed in coloured epoxy grouted to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:4 for laying floor finishes, over and including 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed aggregated)surface finished even and rough to receive floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:4, finished even and smooth without using extra cement including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for 15mm thick rendering in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement, including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and making the surfaces smooth by applying 2mm thick wall care putty and applying two coats of oil emulsion distemper, complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall and applying two coats of exterior emulsion paint of approved brand and shade over a coat of alkali resistant primer including curing, complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall and applying two coats of exterior acrylic weather proof antifungal emulsion paint of approved brand and shade over a coat of alkali resistant primer including curing, complete all as specified and directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads / clips, in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F 3mm thick figured sheet glass, ordinary quality and glazing with oil putty or fixed with beads / clips, in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

Taking down chowkhats or frames not exc 1.5 Sqm each with shutter (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 Sqm but not exc 4.0 Sqm each (without taking off shutters from the frame), complete all as specified and directed.

Dismantling timber scantling 40 Sqm and over in section in unframed work etc complete all as specified and directed.

Taking down wooden roof trusses, coupled rafters or trussed beams, above 4m but n. exc. 8m length clear span complete all as specified and directed.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete and making good disturbed surfaces of walls, floors to match with existing specifications and keeping aside serviceable items for reuse within the same bldg and removing UNSV items from site, complete all as specified and directed.

M&L for point wiring for one light point / fan point / bell point controlled by one switch with 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS cable and 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in and including connected non metallic rigid PVC conduit including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed. Note: The unit rate quoted shall include the cost of cutting chases in surfaces for conduits and fixing of sunken boxes and making good the disturbed surfaces to match the existing surfaces.

Description all as per srl item No. 43.00 here-in-before but for 5 pin 5 amp socket outlet point on independent board controlled by one switch 5 Amps one way, etc complete all as specified and directed.

Description all as per srl item No. 43.00 here-in-before but for 5 pin 5 amp socket outlet point on same board controlled by one switch 5 Amps one way, etc complete all as specified and directed.

Description all as per Srl item No. 43.00 here-in before but for one 3/5 pin 15Amps socket outlet on independent board using 4.00 Sqmm copper conductor wire including 4.00 Sqmm FRLS cable, PVC insulated unsheathed copper conductor earth wire amd making good to disturbed surfacees of wall , floor to match existing finishes etc complete all as specified and directed.

S&F Switch piano flush button, single pole, one way, 5 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F Switch piano flush button, single pole, one way, 15 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F socket outlet, flush type 3 pin, 5 Amps, flush type 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 5/15 Amps flush type, universal complete all as specified and directed.

S&F ceiling rose, surface bakelite, 3 terminals, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F Bell push switch piano flush button, single pole, one way, 6 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F lamp holder insulated body with back plate for batten fittings with polycarbonate body, including LED bulb 12 watt 230 Volts complete all as specified and directed.

S&F fan step regulator, step type suitable for 1200/1400mm sweep ceiling fan, hum free, 240 Volts and connecting electrically, complete all as specified and directed.

S&F bell electric, heavy duty, Ding Dong type, 230 Volts AC, single pole, complete all as specified and directed.

S&F in replacement of surface mounted 1x20 Watt LED tube light fittings (4 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

S&F in repalcement of LED building security light fitting 25 watts, IP 65, having pressure die cast aluminium alloy housing, prismatic polycarbonate cover, making connection with 3 core copper flexible cable of size 23/0.0076 including fixing of street light fitting galvanised iron bracket 0.90m long of suitable dia complete all as specified and directed.

S&F in replacement of bulk head 10 W LED light fitting 6000K, IP 43 in engineering plastic housing with clear primatic diffuser complete with all accessories, connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed.

Note for srl item No 55 to 57 above 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 2 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 02 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover.

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

S&F in replacement of GI tubing light grade 40 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 25x4 mm, nut bolts , washers etc all as required at site complete all as specified and directed.

S&F "in replacement" VTPN distribution board with provision for MCCB as incommer 63A four pole 4 way IP 54 (for incoming MCCB & outgoing MCBs), with copper bus bar for each phase, with Neutral bar, Earth bar and cable ties for cable management, fully insulated bus bar & shrouded Neutral bars, with 63 Amps MCCB, 16 KA, 4 pole, as incomer and 06 Nos SP cap 6-32 Amps MCBs as outgoing complete all as specified and directed. Note:- Rate of MCCBs and MCB, including cutting, chasing, grouting in wall are included in above rate.

Taking down ceiling/exhaust fan by disconnecting from ceiling rose, dismantling blades & hanging ceiling fan back after repair and application of one coat of synthetic enamel paint by spray painting and rewritting number including fixing of blades and including electric connections complete all as specified and directed.

Dismantling and taking out burnt winding by cutting, cleaning slouts and re-winding of AC ceiling fan motor1200mm/1400mm of any make of fan with super enameled heat resistant copper winding wire of existing gauge & nos of turns including, sleeve work, varnishing with E class insulation, greasing, threading, connection with flexible wire 0.472 mm copper wire upto connector block including lath work replacement of nuts/bolts, PVC canopy as required and re-assembling and testing for 4 Hrs after repair complete all as specified and directed. (Repairs will be measured and paid for separately under respective items):- Notes:- (i) Fan shall be collected by the contractor from MES store yard at thier own arrangement. (ii) Motor shall be wound with machine only and repair of fan inside complex/office of GE(S) Mamun. (iii) Khaitan/RPG/KEI or equivallent make super enameled copper winding wire shall only be used. (iv) Rates are deems to be included cost of repair /servicing & replacement of minor spare part i.e. blade screws, capacitors clumps terminal connection , split pin spring washer etc.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated , armoured heavy duty electric cable , with aluminium conductor of size 25 Sqmm x 3.50 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

M&L for dry clean fine river sand as in sand cushioning to underground cable 8cm below and 15cm above the cable including punning down of sand layer complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.

M&L for earthing complete with galvanised GI earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means bolt, nuts, check nuts and washer made of galvanised iron or steel including earth work in any type of soil, charcoal dust and salt layers 15cm thick all around the earth plate as shown in electrical plate No. 03 of SSR Part-I 2009 including 20mm bore GI watering pipe 'medium grade' with funel and wire mesh and 15mm bore GI protection pipe 'light grade' from earth pit to main board including PCC pit in cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) and including angle iron frame of size 40x40x3mm with hold fast embeded in PCC, RCC pit cover with suitable handle and earth work and removal of surplus soil to a distance not exc 50 Mtr, complete all as required at site and directed.

Abrol construction co

M/s GIrdhari Lal Rakesh Kumar

M/S HIMANSHU BUILDERS

WALIA ENTERPRISES

dadwal engineers

RD Engineers

M/S DUGGAL CONSTRUCTION CO

M C ENTERPRISES

AV ENTERPRISES

Bidder Name

dadwal engineers

Abrol construction co

WALIA ENTERPRISES

RD Engineers

AV ENTERPRISES

M/s GIrdhari Lal Rakesh Kumar

M/S DUGGAL CONSTRUCTION CO

M/S NARESH KUMAR SHARMA

M/S HIMANSHU BUILDERS

M C ENTERPRISES