Special repair to Block No. 18 at DAD Colony, Lekha Nagar under GE (East) Jabalpur

Amount

Basic Rate : Refer Schedule'A' Notes

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply and spreading clean and dry fine sand free from sharp materials (unwashed) laying in trenches around the cable for cushioning in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable) and gently punned down to 18cm thickness complete all as specified and as directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debrise to out side MD land complete all as specified & directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debrise to out side MD land complete all as specified & directed.

M&L for PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete and sub base of floors, embedded of posts, path/ paving etc complete all as specified & directed.

M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete and sub base of floors, path/ paving etc complete all as specified & directed.

M&L for 60mm thick rubber mould reflective factory made coloured pre cast PCC interlocking paver blocks/ tiles confirming to IS 15658-2006, M-35 designation of section as approved by GE in hard standing, laid dry over & including 50mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed. Make:- Mehtab Tiles, Indore (MP) or Nitco, Mumbai or Mayur Tiles & Interlocking pavers, Lucknow or Star Tiles & Industries, Ramadevi, Kanpur as approved by GE.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in bed block for hold fast, plinth courses, copings, bed plates etc and the like including weathering slightly rounded/ chamfered angles with & including necessary use and waste of form work for fair faces of concrete, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

M&L for brick work with sub class B bricks, old size straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

Taking down Chowkhats or frame with shutter (w/o taking off shutter from the frame) area n.exc 1.50 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (w/o taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

Taking down shutters of any description area exc 1.00 sqm but n.exc 2 sqm each and removal complete all as specified & directed.

M&L for IInd class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified & directed.

M&L for factory made second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all as specified & directed.

Supply & fix factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick single side wood grain printed PVC sheet reinforced with MS square tube and edges painted to match with printed sheet complete all as specified & directed. Make:- Sintex or Rajshri Plastiwood or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed in frame complete all as specified & directed. Make:- Sintex or Rajshri Plastiwood or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents..

M&L for solid PVC wall lining as in cupboard consisting of 5mm thick single side prelam PVC sheet, PVC beading inclusive of solvent cement and fixing at site with and including on PVC frame made-out of 5mm thick PVC sheet fillet of width 35mm with screws/ manufacturer's instruction complete all as specified & directed. Make:- Sintex or Rajshri Plastiwood or Kumar Arch Teach Pvt Ltd as approved by GE.

Supply & fixed in repairs, PVC vertical partitions/ vertical surfaces of cupboard shelves made out of 18mm thick prelaminated solid PVC Ply sheet of pleasing colours, print and prelam finishes one side as approved and fixed with & including screws/ manufacturer's instruction complete all as specified & directed Make:- Sintex or Rajshri Plastiwood or Kumar Arch Teach Pvt Ltd as approved by GE.

Supply & fixed in repairs, PVC horizontal partitions/ horizontal surfaces of cupboard shelves made out of 12mm thick prelaminated solid PVC Ply sheet of pleasing colours, print and prelam finishes one side as approved and fixed with & including screws/ manufacturer's instruction complete all as specified & directed Make:- Sintex or Rajshri Plastiwood or Kumar Arch Teach Pvt Ltd as approved by GE.

M&L for factory made 40mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed.

Supply & fix 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Supply & fix 50m size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F aluminium handles 150mm size, cast type, anodised complete all as specified & directed.

Supply & fix 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supply & fix 300mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

Supply & fix 300mm size ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified & directed.

M&L for second class hard wood small fittings such as brackets of any type, shaped door and window stops and the like, including all necessary labours, articles not exceeding 200 cu. cm each complete all as specified and directed.

Supply & fix in repairs, tubular towel rail of brass chromium plated, D type, 20mm dia, 60cm long between flanges complete all as specified & directed.

Supply & fix in repairs, 19/20mm mild steel, chromium plated curtain rod fancy type with brackets of brass fancy type fixed on walls with brass screws complete all as specified & directed. Note:- Cost of any number of brackets shall be deemed to be included in the quoted unit rate and nothing extra shall be paid on this account.

Supply and fix factory made steel window flush welded with side hung shutters including box type hinges with steel handle, steel peg stay 250mm long with suitable lugs and with glazing bars dovetailed or welded complete all as specified & directed.

M&L for mild steel conforming to Fe.290.Gde-E-165 in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; will ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified.

Supply and fix factory made steel ventilators with top hung shutter including hinges, steel peg stay omplete all as specified & directed.

M&L for mild steel conforming to Fe.290.Gde-E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work work as in repairs complete all as specified & directed.

Supply and fix mild steel plain black sheet 0.80mm thick in hearths; covering to door shutters; ducts, etc, cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets, fixed to wood or steel members with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, etc as required complete.

Supply and fix stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or any other means as per site requirement complete all as specified & directed.

Taking down/ removing existing roof treatment over roof slab, roughening surfaces of old concrete floor/ roof/ terrace by picking and wire brushing the surface to remove the loose concrete, dust etc sweeping clean and washing down with water to remove dust, etc including removal of debrise to out side MD land complete all as specified & directed.

M&L for 15mm thick rendering over roof surfaces in CM 1:4 with using water proofing compound @ 2% by wt of cement or as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. Note: WPC shall be measured and paid separately as "Supply Only" under respective item of BOQ.

M&L for applying evenly tack coat of hot blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm after cleaning the surfaces over & including a coat of bitumen primer @ 0.30 litre/ sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil on the top of prepared roof surfaces complete all as specified & directed.

M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum over lap of 100mm and over lap shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.

M&L for applying a coat of bituminous aluminium paint @ 100gm/ sqm and blinding material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer's as specified for polymeric water proofing membrane.

Supply only Integral water proofing compound of make as approved by GE complete all as specified & directed.

M&L for 15mm thick rendering to side and bottom of sunken slab in CM 1:3 with using water proofing compound @ 2% by wt of cement or as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. Note: WPC shall be measured and paid separately as "Supply Only" under respective item of BOQ.

M&L for RCC type B-1 (1:2:4) Nominal Mix (20 mm graded stone aggregate) as in slabs suppoorted on walls, beams and column in floors, roof, landings, balconies, canopies, deck slab and in shevels etc complete all as specified. Note:- Reinforcement shall be measured & paid separately under respective item of BOQ.

M&L for providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately under respective item of BOQ.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for fair finished flat surfaces (Horizontal or Sloping) of concrete complete all as specified & directed.

M&L for mild steel TMT bars 10mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.18Sqm but not exc 0.38Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11Sqm but not exc 0.18Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for glazed ceramic coloured tiles 350x250x7mm or 450x350x7mm thick as approved by GE on vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for 18-20mm thick granite of approved quality as in platform i.e. in horizontal & vertical position, machine cut (table rubbed and polished) laid over and including 10mm thick rendering in CM 1:4 and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floor finished even and smooth without using extra cement complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring/ trades of steps, 18-20mm thick over & including 20mm thick cement screed bed in CM (1:6) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for machine cut kota stone slab as in skirting/ vertical surface, 15-18mm thick over & including 10mm thick rendering in CM (1:4) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement forming joints to full depth at every 3M intervals and at every change of direction and filing with bitumen sand mixture 1:3 by weight complete all as specified and directed.

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

M&L for 5mm thick rendering in CM 1:4 with water proofing compound @ 2% by wt of cement or as per manufacturer's instructions over 10mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed. Note: WPC shall be measured and paid separately as "Supply Only" under respective item of BOQ.

M&L for 5mm thick rendering in CM 1:3 on fair faces of concrete surfaces as in ceiling, finished even and smooth without using extra cement complete all as specified & directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparing old plastered or unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for preparing new plastered surfaces of walls and applying two coats of distemper, oil emulsion white or tinted over & including a coat of chalk whitening complete all as specified & directed.

M&L for prepration of old decorated plastered surfaces of walls of any description by complete removal of existing treatment and rubbing/ smoothing the surfaces for treatment and applying two coats of distemper, oil emulsion white or tinted over & including a coat of chalk whitening complete all as specified & directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over & including a coat of white cement primer complete all as specified & directed.

M&L for complete removal of existing treatment on old plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of white cement primer complete all as specified and as directed

S&F sheet glass, ordinary quality 3.0mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in old work, serviceable beads as obtained from hacking out of sheet glass shall be re-used after cleaning/ rubbing the the same with sand paper, if required as per site. (ii) Glazing in new work, beads shall be supplied with joinery.

S&F sheet glass, ordinary quality 3.0mm thick but frosted and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in old work, serviceable beads as obtained from hacking out of sheet glass shall be re-used after cleaning/ rubbing the the same with sand paper, if required as per site. (ii) Glazing in new work, beads shall be supplied with joinery.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat synthetic enamel paint of colour as approved by GE over and including a coat of pink primer complete all as specified & directed.

Supply & fix in repairs, grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified & directed. Make:- PRAYAG SYMET/ COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE over and including a coat of red-oxide primer complete all as specified & directed.

M&L for preparation of old painted surfaces of wood or wood based materials of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

M&L for preparation of old painted surfaces of iron/ steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Cutting chases in brick walls, pinning in brick wall/ stone concrete block or slab walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good as per existing, cutting not exceeding 10cm girth complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 15mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 20mm bore of pipe complete all as specified and as directed.

Supply & fix 15mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified & directed.

Supply & fix 20mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified & directed.

Refixing old steel water tubing 15mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Refixing old steel water tubing 20mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Dismantling water tanks of capacity exceeding 500 litres but not exceeding 1000 litres and removal from site complete all as specified & directed.

Supply and fix 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed. Make:- Sintex or Tuff or JS Poly Plast or Dhara as approved by GE.

Supply & fix 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high dencity plastic ball, screwed for iron pipe or brass ferrule complete all as specified & directed. (Note-Min weight should not be less than 210 gms) Make:- PRAYAG SYMET or COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

M&L in repairs, cast iron Nahani trap 75mm bore dia with grating including jointing to waste pipe in run lead or fixed with PCC 1:2:4 type B0 using 12.5mm graded stone aggregate complete all as specified

Supply & fix in repairs, 15mm dia stop valves/ angle cock, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix in repairs, 15mm dia bib cock, cast copper alloy, long body, long nose with crutch or butterfly handle, fancy type, chromium plated, screwed down for iron pipe or brass ferrule complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix in repairs kitchen sink with drainage board made of stainless steel 1.0mm thick with plug, washers with and including 32 mm dia PVC rigid waste pipes and C.P coupling including fixing cantilever brackets of suitable shape & size as required at site and connecting unions to pipe, overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm and necessary cutting to slab complete all as specified & directed. Make:- Prayag Polymer Pvt Ltd or Jain Brothers Sanitation Pvt Ltd or Blue Star Silver Shine or Nirali or equivalent brand of other Make as approved by GE from list of make attached with tender documents.

S&F in repairs, 15mm dia pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe complete complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix in repairs, brass CP shower rose 125mm dia with arm and flange suitable for 15mm bore GI pipe complete all as specified and directed.

Supply and fix in repairs, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, design & make/ pattern as approved by GE complete all as specified & directed.

Supply & fix in repairs, vitreous china white WHB (550 x 400 mm) flat back with CP waste coupling, waste pipe, brackets including cutting for and pinning in ends of brackets complete all as specified and directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply and fix in repairs, 15mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. Make:- Leader or Bombay Metal & Alloy Co. or Zoloto or NMC or Vardhman or BIR Jalandhar as approved by GE.

Supply and fix in repairs, 20mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. Make:- Leader or Bombay Metal & Alloy Co. or Zoloto or NMC or Vardhman or BIR Jalandhar as approved by GE.

S&F in repairs 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix 32mm bore, low density polyethylene pipe (LDPE) pipes, of pressure rating 6 Kg/cm2, fixed to walls, ceilings or laid in floor fixed complete all as specified and directed.

Supply & fix in repairs, 15mm bore PVC connection pipe 450mm long with PTMT nuts complete all as specified & directed. Make:- PRAYAG SYMET or COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix in repairs, 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including necessary clamps of requird size etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply & fix in repairs, 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including necessary clamps of requird size etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply & fix in repairs, 110mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply & fixed in repairs, 75mm bore PVC (SWR) bends of any radius complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix in repairs, vitreous china squatting pan, Orissa pattern of size 580x440 mm white, with integral foot rest and PVC 'P' or 'S' trap including connection to trap, and to flush pipe, etc (excluding flushing pipe) & provision of cement concrete bedding and making good to floor as per existing complete all as specified & directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of make attached with tender documents.

Supply & fixed in repairs, PVC (SWR) branch piece (single Y), equal or unequal, 110mm bore complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply & fixed in repairs, PVC (SWR) branch piece (single Y), equal or unequal, 75mm bore complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply & fixed in repairs, 110mm bore PVC (SWR) vent cowl complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified & directed.

Taking down main switches/ DB's (alongwith existing board, MCBs & isolators) including removing the same from site and making good disturbed surfaces complete all as specified & directed.

Taking down existing old/ unserviceable sub main wiring of any type and description, removal of teak wood batten/ PVC pipe/ PVC casing & caping and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified and directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one light/ fan/ exhaust fan/ bell point controlled by one no one way piano type switch 5/6 Amps complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on the same board with other switches complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

Supply & fix switch piano, flush type single pole, one way 5/6 Amps, 240 volts complete all as specified & directed.

Supply & fix bell push, single pole one way 5/6 Amps, 240 volts complete all as specified & directed.

Supply & fix socket outlet 2 in 1, 2 pin 5/6 Amps and 3 pin 5/6 Amps, flush universal type complete all as specified & directed.

Supply & fix switch socket combination 2 in 1, 2/3 pin, 5/6 Amps shuttered flush type multipurpose controlled by one switch complete all as specified & directed.

Supply & fix switch socket combination 2 in 1, 3 pins 5/6 Amps and 3 pins 15/16 Amps flush universal type controlled by one switch complete all as specified & directed.

Supply & fix ceiling rose, surface bakelite, 65x50mm surface type, two to three terminals, AC 240 volts complete all as specified & directed.

Supply & fix in repairs, rotory stepped type electronic fan regulator mini flush type 120/ 280 Volts complete all as specified & directed.

Supply and fix in replacement, electrical bell model city ding dong (Ding dong type) AC, 230 Volts complete all as specified & directed. Make:- Anchor or Cona or Plaza as approved by GE.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC rigid conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4.0sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

Supply and fix in repairs, indoor commercial basis all purpose, surface and wall mounted LED batten with polycabonate housing & integrated clectronic driver with and including 20 Watt LED tube and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells Cat Part No. LUMILINEBS20WLED830SPCWH or equivalent model of make- Philips or Crompton or WIPRO or Bajaj as approved by GE.

Supply and fix in repairs, indoor linear & compact, surface and wall mounted, 9W mirror light with decorative grey end caps, polycarbonate body and ribbed opal diffuser with and including LED lamp and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells Cat Part No. LHEXARP7PN1W009 or equivalent model of make M/s Surya Roshni Ltd/ Philips/ M/s Insta power Ltd as approved by GE.

Supply and fix TPN DB-VPTN 12 way sheet metal enclosure, IP 43-IK 09 with metal door, 415 volts with copper bus bar of 250A for each phase and with 2 neutral bar, 2 earthbar and cable ties for cable management all enclosed on standard steel sheet flush or surface mouting type factory fabricated complete all as specified and directed . Make:- Legrand Cat No. 5077 48 or equivalent model of make L&T/ Havells/ ABB as approved by GE. Notes:- (i) Quoted rate shall be deemed to be included for necessary cutting to brick walls to accomodate DB to make flush to wall or fixed on wall with & including MS frame made out of 40x5mm complete. (ii) Quoted rate shall also be deemed to be included for making good the disturbed surfaces as per existing specification.

Supply and fix SPN DB 8 way sheet metal enclosure, IP 43-IK 09 with metal door, 240/ 415 volts with copper bus bar of 100A and neutral bar, earth bar and cable ties for cable management all enclosed on standard steel sheet flush or surface mouting type factory fabricated complete all as specified and directed. Make:- Legrand Cat No. 5076 11 or equivalent model of make L&T/ Havells/ ABB as approved by GE. Notes:- (i) Quoted rate shall be deemed to be included for necessary cutting to brick walls to accomodate DB to make flush to wall or fixed on wall with & including MS frame made out of 40x5mm complete. (ii) Quoted rate shall also be deemed to be included for making good the disturbed surfaces as per existing specification.

Supply and fix in repairs, MCCB 4 Pole, 100 Amps with thermal magnetic protection unit, Ics = 100% of Icu, 415 Volts with rupturing capacity 25 KA complete all as specified and directed . Make:- Legrand Cat.No.4200 55 or equivalent of other Make- L&T or ABB or Schneider as approved by GE.

Supply & fix MCB SPN, 32 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed. Make:- Legrand Cat No. 4086 17 or equivalent model of make L&T/ Havells/ ABB as approved by GE.

Supply & fix MCB SP, 6 to 32 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed. Make:- ABB/ Legrand/ Siemens/ L&T/ Havells as approved by GE.

Supply and fix in repairs, 40 watt new generation energy saving and environmental friendly long life LED street/ security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seperate driver compartment with IP66 protection and impact resistance of IK07 on bldg wall with and including pipe bracket made out of G.I tubing 32/40 mm dia bore medium grade ISI marked 1.20m long bent to shape & providing 2 Nos clamps made out of 50x6mm flat iron/ MS clamps & 12mm dia bolts, nuts & washers etc and two coat painting of approved colour on brackets completely with and including synthetic enamel paint and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells Cat part No. ENDURAPEARLNEOSL40WLED757PASYTOPC or equivalent model of make- Philips or Crompton or WIPRO or Bajaj as approved by GE.

Supply and fix in repairs, angle type lamp holder insulated with polycarbonate body and back plate housed with porcelain base suitable for 8 Watt LED lamp with and including 8 Watt LED bulb complete all as specified and directed. Makes: (i) Anchor/ Plaza for lamp holder as approved by GE. (ii) Crompton or Philips or Havells or WIPRO or Bajaj as approved by GE for 8 Watt LED bulb.

Taking down of existing exhaust/ ceiling fan of any size/ sweep for keeping the safe cosdoy and re-fixing/ re-hanging the same after repair work or as directed and connecting up the same with & including twin twisted copper flexible wire from ceiling rose to exhaust/ ceiling fan complete all as specified & directed.

M&L for earthing in replacement complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear incl 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Supply and laying reinforced precast concrete cable cover, class LV, type-1, flat, size 250x150x40mm complete all as specified and directed.

Supply and fixing/ laying of 50mm bore dia GI pipe light grade in trenches/ under roads/ along pole/ wall including all necessary fittings & clamps made out of 25x3mm flat iron as required for cable protection etc after taking out existing old unserviceable GI pipe with fittings complete all as specified and directed.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 25sqmm, 4.0 core including jointing materials such as cable glands & lugs etc after taking out the old unserviceable cable and testing on completion complete all as directed. Make:- Havells or Finolex or Gloster or Plaza or Universal as approved by GE.

Schedule of credit amount of Rs. 1,45,022.00 to be deducted during AOC

Tiki Water proofing Co

DOBARIA BUILDCON

HAFEEZ CONSTRUCTION

M/S Modern builders

Sachdeva Enterprises

C L BHATIA

RAVI ENTERPRISES