Special Repair of Boys Hostel in Shri Krishna Govt. Ayurvedic College at Kurukshetra in District Kurukshetra

Amount

Cement Concrete 1:4:8 with stone aggregate 20mm nominal size in foundation and plinth. (HSR-10.38)

Providing steel pipe I.S.I. mark in columns with 2 Nos M.S. plates welded on both ends of the pipe including cutting etc., complete fixed in position. (HSR-18.41) 76.1x4.5 mm (medium)

Supplying, hoisting and placing in position tubular trusses including runners, purlins, consisting of steel tubes conforming to I.S. specifications of tested quality duly welded with fillet welds 6 mm thick through-out including wind bracing. Open end of pipe sealed with 3 mm thick plate including the cost of nuts and bolts where bolts connections are specified at flange joints including one coat of ready mixed red oxide zink cromate primer of approved quality assembling and fixed in position complete in all respect. (HSR-18.14)

Providing & fixing Polycarbonate 1.25 mm thick ISI mark sheet of PC lite (Ultra voilet resistance) make(N.S.)

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete.(HSR-14.92 (A) ) Size of ceramic Glazed tiles 200 X 300mm

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete: -door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate (HSR-18.34(b )

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete: -door and window frame of size 114 mm X 50 mm with 35 mm wide double rebate (HSR-18.34(d )

Scraping cement plaster (HSR-8.32 (C)

White wash and colour wash (HSR-8.32(a)

Providing and two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get en even smooth finish including cost and carriage of all material , labour charges, scaffolding , sundries etc. completed (JK/Birla Make) (HSR-16.81)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces.(HSR-16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work.(HSR-16.60)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR-16.5)

Providing two coats of exterior acrylic emulsion paint.(a) 1st Quality (HSR-16.79(B)

12 mm thick cement plaster 1:6 (HSR-15.7)

Pdg & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in floors, laid in any pattern as specified over base of 20mm thick cement oarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR-14.91)

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin,hot- pressesd, conforming to I.S.2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)-(a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.)35 mm thick (HSR-17.93) iii

Providing and fixing commercial type block board, plain lining, butt jointed, including wooden plugs (teak) placed at 45 cm to 60 cm centres, complete with necessary nails (frame work shall be payable extra).19 mm thick (HSR-17.49)b

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Note:- reputed make such as Duro, Green, Kitply will be used as approved by Engineer-in-charge). HSR 17.93 (a) - Note 1 under 17.18). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (i) 25 mm thick.

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ,chikrassy and chaplash,etc.,(non-coniferous timber other than teak,conforming to I.S.specification No. 1003,kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges ,screws,chocks/ cleats,stops,nails etc., complete,fixed in position (excluding the cost of any fittings, other than specified above,but including labour for fixing the same in position).35 mm thick (HSR-17.90) B

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash ,etc.,(non-coniferous timber other teak, conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail, and wire gauze of 140G or 120G designation including cost of iron hinges, screws,chocks/cleats,stops nail etc.,complete fixed in position (excluding the cost of any fitings,other than specified above,but including labour for fixing the same in position)-35 mm thick (HSR-17.92) b

Supplying and fixing glass panes including special metal sash putty of approved make (b) glass panes 4 mm thick, exceeding 40 sq dm areas. (HSR-18.30(b)

Spirit polishing one coat on old work. (HSR-16.44)

Providing and laying 60mm thick inter locking paver blocks of all shapes and colours in design mix cement M-35 over a bed of 25mm thick finesand complete in all respect. (HSR-10.158)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab /( 0.1 mm thichness polythene) including grouting with cement sand mortar 1:3 and top surface to be left clean (HSR-13.13)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1: 3 and top surface to be left clean.(HSR-13.14)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete.(HSR-16.1)

WATER CLOSET SUITES PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Size 580 mm Single colour (HSR 30.1(a)(i))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NON- CONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary fittings as fully described in item no.30.3 above. White (HSR 30.4) ( I)

Providing and fixing in position best Indian make lavatory suites (with full anti splash rim in vitreous Chinaware and all other necessary fittings as fully described in item No. 30.41 above. WHITE Size 530mm X 430 mm with one no. tap(HSR-30.42) (a) (II)

PROVIDING AND FIXING POSITION BEST INDIAN MAKE FLAT BACK OR ANGULAR LIPPED FRONT URINAL 465 MM HIGH CONSISTING OF : -(iv) Standard size G.I.FLUSH PIPE WITH C.P.BRASS WALL CLIPS AND UNIONS COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOOR AND PAINTING OF FITTINGS ETC. (as required by the Engineer-in-charge White HSR (30.19) (IV) (I)

EXTRA OVER item nos. 30.1 TO 30.4 AND 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 litres capacity high level C.I. eistern complete (as approved by the Engineer-in-charge).White HSR (30.8) (I)

EXTRA FOR PROVIDING AND FIXING STANDARD SIZE C.P.BRASS FLUSH PIPE COMPLETE WITH FITTINGS INSTEAD OF G.I.FLUSH PIPE COMPLETE.For single urinal HSR (30.38) (I)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE C.P.BRASS INLET CONNECTION 15 MM WITH 375 MM PIPE AND C.P. BRASS NUTS HSR (30.83)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D IN-LET.C.P. brass with revoiving joint HSR (30.66) {C}

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge)15 MM STOP COCK Stop cock male and female end HSR (30.76) (A) (I)

EXTRA OVER item nos.30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid.White plastic seat (Solid) HSR (30.13) (I)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). Bib cock sparrow with Perimix and flange HSR (30.75) (B)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge).Bib cock HSR (30.75) (C)

PROVIDING AND FIXING IN POSITION ON BEST INDIAN MAKE CHROMIUM PLATED BRASS 2ND TAP FOR LAVATORY SUITE HSR (30.45)

EXTRA FOR PROVIDING AND FIXING VITREOUS automatic flushing CISTERN INCLUDING FITTINGS and brackets instead of C.I. flushing cistern COMPLETE10 Litres capacity cistern White HSR (30.37) (B) (I)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE VITREOUS CHINAWARE SINKS WITH COMPLETE FITTINGS AS FULLY DESCRIBED IN ITEM NO.30.51 ABOVE.600mm X 450mm X 200mm HSR (30.52) (A)

Providing and fixing 25mm thick marble partition for different type of urinals. VITREOUS CHINAWARE PARTITION PLATE Single colour SMALL SIZE 680mm X 330mm HSR (30.40) (B) (II) (I)

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the wells etc.C.P.BRASS Soap dish small HSR (30.70) (A) (II)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETCINDIAN MAKE 550mm X 400mm HSR (30.71) (A) (II)

PROVIDING AND FIXINGIN POSITION GULLY TRAPS FIXED IN CEMENT CONCRETE 1:4:8 complete WITH H.C.I.GRATING 150 MM X 150 MM CAST IRON COVER WEIGHING APPROXIMATELY 7.26 K.G. AND FRAME CLEAR OPENING 300 MM x 300 MM and outside size 330 MM x 330 MM AND CHAMEBR INCLUDING cost of all brick work in CEMENT MORTAR 1:5 CEMENT CONCRETE 1:8:16 IN FOUNDATIONS, AND CEMENT CONCRETE 1:2:4 IN COPING around C.I. cover and frame etc. WITH THREE COATS of black bitumastic superior PAINT of approved manufacture on all C.I. work AS PER STANDARD DESIGN, minimum depth of water should be 150mm with a minimum seal 50mm.100 mm internal diameter S.W. gully trap HSR (30.114) (A)

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer- in-charge)15 MM STOP COCK Concealed stop cock with flange HSR (30.76) (A) (II)

Cement concrete 1:2:4 gola 10cm X 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified. HSR (13.64)

Wrought iron and mild steel (using angles, flats, square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors HSR (18.12)

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. [HSR 30.119]. 1000 Ltrs. Capacity Water Tank

Note: In case of any difference in the unit & nomenclature of any of the HSR items depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable.

THE RADHA KRISHNA CO OPERATIVE LABOUR AND CONSTRUCTION SOCIETY LIMITED

SWAN GROUP OF INDUSTRIES

M/s perfect Rays Technologies Pvt Ltd

Sangroha Coop L and C Society

Mannat Associates