REPAIR TO ROOF TREATMENT, SUNKEN FLOOR, CHAJJA, PARAPET ETC IN MD ACCN AT VARIOUS LOCATIONS OF AGE B/R-V UNDER GE (MCTE) MHOW

Amount

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc., separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M as directed by the Engineer in Charge.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 using old size bricks, complete all as specified

M&L for brick work with old sized fly ash bricks built in CM 1:6 in straight or curved on plan exceeding 6m mean radius complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise described comlplete all as specified and directed.

Use & waste of Formwork to sides and soffits of coping beam fair finish surfaces.

M&L for mild steel TMT bars 8mm dia and over, cut to length,bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for RCC 1:2:4 type B1(20mmgraded aggregate) as in Chajjas & roof slabs complete all as specified and as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

S&F Plain, galvanised, mild steel sheeting thickness 0.63mm , in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

Dismantling of timber scantling as fillets, rails, posts, rafters, purlins, any section & any description complete all as specified and as directed.

S&F Steel work in tubular trusses, purlins etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240etc complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description ,over 10 cm width or girth and applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for, separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M as directed by the Engineer in Charge.

M&L for PCC 1:5:10 type E2 using 40mm graded aggregate as in Mass concrete in sunken treatment complete all as specified and as directed.

M&L for water proofing treatment to sunken surfaces of the slab in following sequences with 10 year gaurantee & testing for water tightness:-

(a) Slope correction by using M-20 (Nominal Mix) concrete minimum 25mm thickness at one end and a slope of 1:20 by using 12.5mm graded stone aggregate with integral water proofing Chemical PIDI PROOF-LW mixed in proporation 200ml/ 50 Kg cement of approved make in proporation 200ml/ 50 Kg cement or equivalent as per manufacturer instructions complete.

(b) PCC padding with cement concrete 1:1.5: 3 type A 0 (using 12.5 mm graded stone aggregate) 25mm thick with integral water proofing compound approved make as per manufacturer instructions complete.

(c) Vertical sides plastered in CM 1:3, 15mm thick with WPC and 72 hours testing for water tightness by ponding of water complete.

(d) Application of two coats proof coats black manufactured by approved make manufacturers instructions all over and testing again for water tightness by ponding of water for 72 hours complete.

M&L for Cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry as on roof surface with grey cement and pigments, and cut and polished etc incl 15mm thick screed bed in CM (1:6), complete all as specified and as directed

Taking down existing waterproofing treatment of tar felt of any description from roof surfaces and removing rubbilsh to a distance not exc 100m complete all as specified and directed.

M&L for rendering 10 mm thick screed bed on concrete surfaces in CM(1:3) finished even and smooth without using extra cement complete all as specified and as directed.

M&L for PCC 25mm thick (1:2:4) type Bo using 12 mm graded stone aggregates mixed with integral waterproofing chemical mixed in proportion of 200ML/ 50Kg cemet of approved make in proportion 200ML/50Kg cement as in padding on roof surfaces for correcting/ making proper slope on roof/chhaja and roof kerbs/ benching complete all as specified and directed.

Supply, providing & testing water proofing roof treatment with polymeric standard water proofing membrane, Aquaflex manufactured by M/s Bengal Bitumen, MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd/ Hyperplas manufactured by IWL Ltd or equivalant approved by the GE having 10 years gaurantee for water tightness complete all as specified and described as under:- (a) Preparation of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per manufaturer's specification complete all as specified and directed. (b) Supply & providing water proofing with 3mm thick APP polymeric proofing membran of 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed. Aluminium bituminous paint @1.10 Kg/Sqm shall be applied over the APP membrane surface. Note:- The work of water proofing treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer.

M & L for Water proofing on roof/wall with the follwing steps including 10 year gaurantee & testing for water tightness:- STEP-1. Firstly to clean the existing surface and make the surface dust free. STEP- II. Crack more then 0.5mm the opening of crack in V grove and filling with epoxy mortor. STEP-III. Initial coat (mixed 1/2 liter of water in 1 liter of Roof/wall seal of Asian paint/ PIDILITE/ STP/ FOSROC/ACC/ L&T/MARUIT) as a primer (Area cover 1 liter=9-10 sqmtr) STEP-IV. After six hours of primer, apply first coat( one coat) of Asian paint/ PIDILITE/ STP/ FOSROC/ACC/ L&T/MARUIT. roof / wall seal in a particular direction without mixing of water. Now left it for six hours (Area cover 1 liter= 1.2 sqmtr). STEP-V. After again six hours of first coat and apply the second coat of Roof / wall seal in a other direction without mixing of water ( Area cover 1 liter= 1.2 sqmtr). Now left it 24 hours. all as specified and directed by Engr-in-Charge Note:- The work of water proofing treatment shall be got executed through expert team of manufacturers of authorised applicator of manufacturer. Make : Asian paint/ PIDILITE/ STP/ FOSROC/ ACC/ L&T/ MARUIT or equivalent approved by the GE.

S & F in repairs 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench including removing existing complete all as specified and directed.

S&F in repair 1000 litres capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position including removing the existing water tank all as specified in SSR Part I complete all as specified and as directed.

S&F in repair 500ltr capacity rotational moulded polythyiene water storages tanks (cylindrical vartical with closed top) hoisted and fixed in position including removing the existing water tankall as specified in SSR Part-I complete all as specified and as directed.

Disconnecting existing tanks (exc 500 but n. exc 1000 ltrs capacity), setting aside (or lowering if required) for Cleaning and removing all scale and dirt, etc, from tanks. The complete tank be scrubbed to remove dirt, sediments, fungus & stains . The vacuumed tank is disinfected with anti-bacterial spray or liquid bleach. Tank is filled with water that is made to run through the taps to disinfect the water pipes , etc. and hoisting if required reconnecting and re-fixing in the same positiondate of cleaning should be write by erasing the previous date of cleaning with paint and further writing the current date of cleaning.

Disconnecting existing tanks (exc 250 but n. exc 500 ltrs capacity), setting aside (or lowering if required) for Cleaning and removing all scale and dirt, etc, from tanks. The complete tank be scrub to remove dirt, sediments, fungus & stains . The vacuumed tank is disinfected with anti-bacterial spray or liquid bleach. Tank is filled with water that is made to run through the taps to disinfect the water pipes , etc. and hoisting if required reconnecting and re-fixing in the same position incl writing the date of cleaning should be write by erasing the previous date of cleaning with paint and further writing the current date of cleaning.

S & F CPVC 20mm outer dia pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors incl taking up or down steel tubing pipes 20mm complete all as specified and as directed.

S & F CPVC 25mm outer dia pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors incl taking up or down steel tubing pipes 25mm complete all as specified and as directed.

S & F CPVC brass elbow (3/4" X ½") for 20 mm outer dia CPVC pipe complete all as specified and directed.

S & F CPVC Male Brass Threaded Adaptor (MTA/ MBTA) for 25 mm outer dia pipe complete all as specified and directed.

S & F CPVC Tank Adaptor for 25 mm outer dia pipe complete all as specified and directed.

S & F CPVC union for 25 mm outer dia pipe complete all as specified and as directed.

S & F CPVC Ball Valve for 25 mm outer dia pipe complete all as specified and directed.

Taking down cement or cement lime plaster of any description including racking out joints, hacking for keys , scrubbing down with water etc, complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of concrete/brick interior surfaces in cement mortar 1:6 as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete exterior surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound wherever required complete all as specified and as directed.

M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces of ceiling, chajja in CM 1:3 surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coat of distemper oil emulsion incl priming the surface and incl one coat of birla white wall putty complete all as specified and as directed.

M&L for preparing newly plastered surfaces of walls and applying two coat of cement based paint complete all as specified and as directed. (Note : Rate shall be included for necessary scaffolding and safety measures where required at site )

M&L for preparation of newly plastered surface and applying three coats of white wash on ceiling complete all as specified and as directed.

M&L preparation of old plaster surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

M&L preparation of old plaster surfaces of ceiling and applying one coat of distemper complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint on old wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint on old steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface complete all as specified and as directed.

M&L for preparation of surfaces and applying one coat Acrylic emulsion with roller on old treated surfaces of wall etc complete all as specified and directed (Note:- Contractor shall furnish gaurantee of four year against service rendered) (Note:- primer and emulsion paint shall be carried out through air less spray machine (Mechanical means)

M&L for complete removal of existing treatment and preparation of surfaces and applying two coat Acrylic emulsion with roller over applying minimum 1mm thick birla white wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and directed (Note:- Contractor shall furnish gaurantee of four year against service rendered) (Note:- primer and emulsion paint shall be carried out through air less spray machine (Mechanical means) Make :- Asian (Tractor emulsion) Dulux (A-700) Nerolac (Beauty Gold) Berger (Pit Bision acrylic interiror emulsion)

M&L for complete removal of existing treatment and preparation of wall, washing, scrubbing down and stopping old treatment and painted surface of plastered/ decorated surface and applying two coat of Premium Acrylic smooth exterior paint and including priming coat of exterior primer and incl one coat of birla white wall putty complete all as specified and as directed. (Note:- painting will be done by brush/ spray/ roller of building upto the height G+3) all as per directed by Engr -in-Charge) (Note : Rate shall be included for necessary scaffolding and safety measures where required at site)

M&L for preparation of old surface of wall, washing, scrubbing down and stopping old treatment and painted surface of plastered / decorated surface and applying one coat of Premium Acrylic smooth exterior paint complete all a specified and as directed. (Note : painting will be done by brush / spray / roller of building upto the height G+3) all as per directed by Engr -in-Charge) (Note : Rate shall be included for necessary scaffolding and safety measures where required at site)

M&L preparation of old plaster surfaces of wall and applying one coat of white wash all as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing debrish and rubbish off the premises and stacking serviceable tiles .

M&L for Vitrified Ceramic tiles 10mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per item No.58 but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per item No.60 but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.09 sqm but not exceeding 0.11 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per item No.62 but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of 300 x 200 x 7 mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and as directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of 300 x 450 x 7mm/ 300 x 600 x 7mm thick in vertical surfaces, as in dado/ skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

Demolition of stone slabs of any description or thickness in floors/ walls laid bedded and pointed in any mortar etc. complete removal of debris outside MD land.

M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per item No.67 but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L 16 to 18mm thick Granite (of any type) work (table rubbed and polished and exposed visible edge moulding/ rounding) in steps, jambs, pillars, window cills, cooking platforms and like in 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Demolition of cement concrete (including floor tiles, kota stone flooring etc) (un-reinforced) of any description and in any position not otherwise specifically provided for incl remoal the demolised materials to a distance exc 50 mtr and not exc 100 mtr complete all as specified and as directed.

M&L for PCC 75 mm thick type B2 (1:2:4) using 40 mm graded stone aggregate) in plinth protection, joints should be filled with bitumen primer etc, complete all as specified and as directed.

M/s Shree Ganesh Traders

J B CONSTRUCTION AND DEVLOPERS

sunway associates