SPL REPAIR TO BLDG NO T-18 (OR LIVING) NEAR OLD APS, SPL REPAIR TO FLOOR TILES OF BLDG NO P-3 (OFFICE ANNEXE) AND CERTAIN REVENUE WORKS AT DINJAN MIL STN UNDER GE DINJAN

Amount

Demolition of brickwork built in cement mortar including taking out roots vegetation if any at any position and removal from site, complete all as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, wall etc. complete all as specified and directed

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level), removing rubbish off the premises etc complete all as directed

Demolition of cement concrete (reinforced) of any description and in in any position not otherwise specifically provided for, removing rubbish off the premises etc complete all as directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position of Un-Framed work, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition and breaking up of drain pipes (salt glazed were or AC or reinforced cement concrete) set in cement mortar of 150/160mm dia complete all as specified and as directed.

Demolition and breaking up of drain pipes (salt glazed were or AC or reinforced cement concrete) set in cement mortar of 200/225mm dia complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as directed.

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retreived debris as directed including necessary scaffoldings etc complete all as directed

Taking up or down 15 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed.

Taking up or down 20 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed.

Dismantling water tanks and removing to store of (exceeding 500 ltr & not exceeding 1000 ltr capacity) complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

Surface excavation n exc 30cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.50 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm, watering and removing surplus soil to a distance not exc 50 m and making good surfaces in soft/loose soil complete all as specified and as directed.

M&L for Hardcore of Broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging 12mm dia holes with cement mortar (1:2) to match the existing etc. in apron complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar (1:2) to match the existing etc. in apron complete all as specified and as directed.

M&L for plain cement concrete (1:4:8) type D-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L PCC 1:2:4, type B2 (using 40mm graded crushed stone aggregated) as in surfaces channels and drains incl necessary formwork complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C1(20mm graded stone aggregate) as in copings, bed plates, etc complete all as specified and directed.

M&L plain cement concrete Type B0 1:2:4 (using 12.5mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, benching, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed inclusive of necessary form work complete all as specified and directed.

M&L precast reinforced cement concrete, type B1, 1:2:4 (20 mm graded aggregate) as in cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and similar work incl necessary formwork set in cement mortar 1:4 complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. all as specified and as directed.

M&L for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concrete water tubing or concrete conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed.

M&L for second class hardwood, scantlings, wrought, in timber framed and fixed work complete all as specified and directed.

S&F Solid PVC moulded door Frame of size 50mm x 47mm made out of 5mm, single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, as directed.

S&F 150 mm long aluminium, anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 100 mm size, butt hinges, heavy weight, cold rolled mild steel complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodized, 150 mm long , complete all as specified and directed.

S&F in repairs curtain rails, Harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail, D type, 60cm long, 20mm dia with brackets complete all as specified and as directed.

S&F in repair floor door stopper with overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repairs Aluminium (Extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

S&F for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing complete all as specified and directed by the Engr-in-Charge.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F mild steel work in Tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches, etc. king rods andstraining bolts conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F mild steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and as directed.

M&L for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

S&F mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) including drilling holes complete all as specified and as directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and conforming to Fe 410-W (Gde-E-250) Quality A complete all as specified and as directed.

S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. steel conforming to Fe 410-W (Gde-E-250) quality A, complete all as specified and directed by Engineer-in-Charge..

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed.

M&L for anodised aluminium frame of doors, windows, ventilators with one or more rebates including joining cleats for fixing etc including powder coating of minimum 50 micron thickness complete all as specified Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing element of these items shall be deemed to be included in quoted rate.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F for anodised aluminium grill, (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design / pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screw @200mm c/c, including cutting the grill to proper opening size for fixing approved anodised aluminium standard section around the opening, complete all as per manufacturer instruction and directed by Engr-in-Charge.

S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of white wash complete all as specified and as directed. Make of E-Board : Eternit Everest / Lafarge/ Armstrong/Visaka Industries Ltd.

S&F 0.71mm thick plain, aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (as in crumple joint) complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and as directed. Note : Colour of ridge shall be same colour as that of sheet used for roof.

S&F 1.25mm Thick 150mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges, complete all as specified and directed.

M&L 18/19 mm thick pre-laminated particle board, interior grade, pre-laminated both side with decorative choice laminated fixed with screws to timber frame work as in cup board shutters, partitions and shelves complete as specified and directed.

M&L for coloured 450x300x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting, dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in skirting. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

M&L for vitrified ceramic tiles light shade, 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over 15 mm thick screed bed or bedding layer of cement mortar in (1:6) for laying floor finishes complete all as specified and as directed.

M&L for Vitrified Ceramic tiles light shade 10mm thick (Square/rectangular) polished area of each tile not exceeding 0.36 sqm of light shed in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match in shade of tiles over and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed. irected.

M&L for machine pressed precast conctete interlocking paver block, design & shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. complete all as specified and as directed.

M&L for prepolished,chequered cement concrete tiles of size 25cmx25cmx22mm thick, as in floors etc, including 15 mm thick screed bed or bedding in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection/ hard standing etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as sub base of flooring complete all as specified and directed.

M&L for 100 mm thick plain cement concrete (1:2:4) type B2 using 40 mm graded stone aggregate as in sub-base of floors, plinth protection etc. finished the surface of concrete fair and even, complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B0 (using 12.5 mm graded stone aggregate) as in leveling etc complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement mortar in (1:4) using water proofing compound in top layer and finished even and smooth (without using extra lime or cement) complete all as specified and directed. Note: Water Proofing Compound measured and paid separately.

M&L rendering 15 mm thick on one side of lathing in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement as specified and as directed.

M&L rendering 10 mm thick on other side of lathing in cement mortar 1:4 and finished the surfaces even and smooth without using extra cement as specified and as directed.

M&L for rendering 5mm thick in cement morter (1:3) on ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Supply only liquid Water Proofing Compound ISI marked of approved make complete all as specified and directed.

M&L for GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste fixed with tinned tacks of wire staples complete all as specified and as directed.

M&L for applying three coats of white wash on new wall surface including preparation of surface, complete all as specified and directed.

M&L for preparation old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moss, efflorescent, having oil and greases spots and applying two coats of cement base paint complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls etc and applying two coats of oil bound distemper over a coat of chalk whiting priming paint over 1.50 mm thick wall care putty complete all as specified and as directed.

M&L for preparing old decorated surfaces of walls by complete removal of existing treatment and applying two coats of distemper-oil-emulsion over a coat of primer including 1.5 mm thick wall care putty complete all as specified and as directed.

S&F 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50sqm in each pane , complete all as specified and directed.

M&L for preparing of old painted wood and wodd based surfaces of any description over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing of old wooden surfaces of any description , but not exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

S&F 15 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

S&F 20 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

Relaying/refixing only old serviciable galvanised steel tubing 15 mm bore in new or old location using new fitting and fixures complete trenches/walls/floors complete all as specified.

Relaying/refixing only old serviciable galvanised steel tubing 20 mm bore in new or old location using new fitting and fixures complete trenches/walls/floors complete all as specified.

S&F in repairs plastic water closet seat cover, back, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified and as directed.

S&F in repair PVC low level flushing cistern, 10 liter capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC connection pipe and flush pipe of polyethylene of low or high density complete all as specified and as directed.

S&F in repairs vitreous china wash basin, size 550x400mm, white, flat back, including 32mm bore PVC (HDPE) waste pipe 450mm long, 32mm bore CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed.

S&F in repair 450mm long PVC connections 15mm size with PTMT nuts, complete all as specified and directed.

S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash basin suitable for 32mm/40mm dia, lenth not less than 70 cm, connected to PVC waste coupling/fittng complete all as specified and directed.

S&F in repair MS grating 75/100mm dia, with or without hole for waste pipe of approved make including fixing with cement mortar(1:6) to floor/nahani trap etc complete all as specified.

S&F in repairs, 15mm Bib taps, cast copper alloy with crutch or butterfly handle, , screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repairs 15 mm bore, stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15 mm bore, Pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with seat and cover complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and as directed.

S&F in repair vitreous china bowl urinal bowl type, of size 465x355x265mm, white (minimum) with grating and union for discharge pipe (excluding flushing cistern but including flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete mortar complete as specified and as directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

S&F in repair CP Soap dish holder including CP screws complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F in repair PVC (SWR) pipes type 'B' 110mm bore, single socketed in any length with rubber ring joints fixed to walls using MS holder bat, fixed complete all as specified and as directed.

S&F in repair PVC (SWR) pipes type 'B' 75 mm bore, single socketed in any length with rubber ring joints fixed to walls using MS holder bat, fixed complete all as specified and as directed.

S&F PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore, complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm bore, complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 110mm bore, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, complete all as specified and directed.

S&F CI Floor trap 100mm diameter of outlet, with gratings, including jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as directed.

S&F in repair PVC (SWR) floor trap dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in repair brass cast copper alloy, chromium plated shower rose 125mm size with shower arm 15mm size, 195mm long fixing to steel pipe or to unions complete all as specified and as directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairstainless steel peg set of 6 peg , 45 cm long complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe including 20 mm bore, ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixedcomplete all as specified and as directed.

S&F in repair 20 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F 150mm bore, reinforced concrete pipes, class NP3, laid and jointed in CM(1:1) complete with collars

S&F for 200mm bore, reinforced concrete pipes, class NP3, laid and jointed in CM(1:1) complete with collars

M&L for concrete bed , plain cement concrete (1:3:6) type C-2 ( using 40mm graded crushed stone aggregate) in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm pipe, complete all as specified and as directed.

M&L for concrete bed , plain cement concrete (1:3:6) type C-2 ( using 40mm graded crushed stone aggregate) in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested, for 200mm pipe, complete all as specified and as directed.

M&L for salt glazed stone ware drain pipes 150 mm bore, grade 'A' laid in trenches, jointed cement mortar and tested complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and plastering the distrubed portions in cement mortar (1:3) to match with surround surfaces, cutting out existing benching and forming branch channel (1/2 round or 3/4 round section) in cement concrete (1:2:4) type B-1 finished smooth and reforming benching as required for 150/160mm bore pipe complete all as specified and as directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound, Grade ‘A’, complete all as specified and directed.

E/M Portion: Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

M&L for point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLHS PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point terminated in and including 1.6mm thick mild steel sunken terminal box of suitable size with 3mm thick hylam sheet top cover fixed with suitable size of brass screws suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and as directed.

All as per Item No.135 above but for One 2/3 pin socket outlet 5/6Amps on independent board

All as per Item No.135 above but for One 2/3 pin socket outlet 5/6 Amps on the same board with other switches.

All as per Item No.135above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm

All as per Item No.135 above but for one switch socket combination 15/16 Amps on independent board with cable 4 sq mm size and earth wire 4 sqmm

S&F Switch piano, flush type, single pole, one way switch 5 Amps. (Note :- switches to be used both for new point wiring and old switch boxes of existing wiring)

S&F Socket outlet 5 in 1, 5 Amp flush type universal, 240 volts, complete all as specified all as directed.

S&F Switch socket combination 3/5 pin, 2 in 1, 5 Amps flush type, 240 volts, complete all as specified all as directed. .

S&F Switch socket combination multipurpose 3/5 pin, 5 A /16 Amps, 5 in 1, flush type, 240 volts, complete all as specified all as directed. .

S&F Ceiling rose surface PVC, 3 terminals 25x50mm all as directed.

S&F electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 sweep/1400 mm, 120 Watt complete all as specified and directed.

S&F lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings including fixing for one 9 Watt LED Lamp complete all as specified and as directed.

S&F LED lights fitting 1x 18/20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F inverter type LED batten(1.2m) made of CRCA sheet housing with PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumen at a minimum system efficiency of 115 lumen per watt and total power consuption not more than 18/20 Watt including driver, it has a rated system life time 40000 burning hour at L70 and should have a colour temperature of 6500K, CR>80, THD<10% and PF>0.95, complete all as specified and as directed.

S&F MCB distrubution board TPN 4 way double door, sheet steel, phosphatised, powder coated with 200 amps bus-bar, neutral link, earth bar and din rail, 415 V, complete all as specified and directed. by Engineer-in-charge.

S&F MCB distrubution board SPN 8 way double door, sheet steel, phosphatised,powder coated with 200 amps bus-bar, neutral link,earth bar and din rail 240 V , complete all as specified and directed. by Engineer-in-charge.

S&F MCB TPN, 415 volts 40- 63 Amps, 16 KA breaking capacity, C series, adjustable thermal and adjustable magnetic

S&F MCB Single pole and neutral, 40 to 63 Amps, 240 volts 10 KA rupturing capacity, C series complete all as specified and directed by Engr-in-charge.

S&F MCB Single pole, 240 volts 6 to 32 Amps 10 KA rupturing capacity, C series complete all as specified and directed by Engr-in-charge.

S&F MCB Single pole and neutral, 6 to 32 Amps, 240 volts 10 KA rupturing capacity, C series complete all as specified and directed by Engr-in-charge.

M&L for sub main wiring with two run of 6 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping of suitable size, fixed on surface of wall/ceiling etc with all necessary fittings and accessories and one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

M&L for clear sand cushioning with dry clean sand for protection of cable, 15cm below the cable and 8cm above the cable, complete all as specified and as directed. Note : Punned thickness shall be measured for payments.

Supply and laying well burnt bricks, sub class 'B' bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

Boring of holes horizontal for laying not less than 80/50/40/32mm pipe (minimum depth 0.75 mtr from top level) under the road pavement, hard standing using trenchless technology complete all as specified and as directed. Note : cost of accessories required for making hole/bore deemed to be included in the quoted rate.

Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volt grade with stranded aluminium conductor of size 10 sq.mm 4 core, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe incl taking down old unserviceable one complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items. (2) Excavation and earth work shall be measured and paid separately. complate all as specified and directed.

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. complete all as specified and as directed.

S&F in repairs 35/40 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. including all fixing arrangement and taking down old light fittings of any type complete all as specified and as directed.

S&F street light bracket arm of length not less than 1.5 m made out of GI tubing, 40 mm bore, light grade fixed to pole, etc with suitable size flat iron clamp, nuts, bolts including painting with two coats of aluminium paint over a coat of red oxide, zinc chrome primer on steel surfaces complete all as specified and as directed.

M&L for earthing complete with GI earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25m below ground level with the top edge of earth plate at depth not less than 1.5m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @ 15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers, necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing the base in which pit cover rests made up of MS angle iron (Frame) complete as specified and as directed.

Garg Brothers (BID ID -3379382)

M/S A K BROTHERS (BID ID -3381419)

M/S CHANDAN ENTERPRISE (BID ID -3381151)

M/S A K ENTERPRISE (BID ID -3381434)

M H KHAN (BID ID -3378026)

STANDARD ELECTRIC WINDERS (BID ID -3381191)