ADDITION/ALTERATION TO EXISTING ROOMS IN HF AND COO HANGAR FOR POL AND ULTRASONIC LAB, RENOVATION OF UNIT CAFETERIA, PROVN OF MODERATE DUTY RO WATER PLANT WITH STORAGE AT HF AND ADDITIONAL/ ALTERATION OF DSC REST ROOM AT COO HANGAR IN AIRPORT AREA

Amount

Dismantling of brick work or stone/boulder masonry built in cement mortar including all quoin arches, pillars etc but excluding ashlars facings, dressed stone work and pre cast concrete articles and removing debris outside MOD land. complete all as specified and directed by Engr-in-charge

M&L rendering 15mm thick in CM 1:4 on fair faces of brick surfaces of walls finished the surface fair and even complete all as specified and directed by Engr-in-charge.

Dismantling of cement concrete of any description and in any position not otherwise specifically provided for including old tarfelt etc and removing them outside MOD Land complete all as specified and directed by Engr-in-charge.

M&L PCC 1:3:6 type C1 (20 mm graded agg) in roof padding complete all as specified and directed by Engr-in-charge.

Rendering 10 mm thick in CM (1:3) mixed with WPC finished even and smooth without using extra cement when the concrete surface of roof padding is green complete all as specified and directed by Engr-in-charge. (Note :- WPC to be measured and paid separately )

Supply only integral water proofing compound complete all as specified and directed by Engr-in-charge

M&L wire brushing and cleaning top surface of tiles lime terracing or cement concrete, including flashings and junction of parapets etc and surface painting with a layer of blown bitumen of any penetration applied hot @ 1.7 kg per sqm complete all as specified and directed by Engr-in-charge..

M&L APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non ovne fabric (wt not less than 150 gms/sqm) laid on primed surface by torched application complete all as specified and directed by Engr-in-charge.

M&L preparing surfaces of roof new or previosuly untreated surface applying 2 coats of bitumenous base aluminium paint over a coat of priming paints plastered coat complete all as specified and directed by Engr-in-Charge

M&L for powder coated (minimum thickness of powder coating 50 micron ) aluminium Door/ window/ sliding window / Ventilator / partition frames and shutters using standard aluminium powder coated sections including necessary joining cleats, glazing clips, rubber packing powder coated aluminium snap beading, screws, including anodised aluminium fittings suitable Nylon gasket, nylon rollers, maruthi locks, handles, concealed star lock, aluminium F channel for fixing aluminium grill and all necessary fittings and fixtures etc all as specified complete, of standard sections and fixed to cudappa stone/granite stone with necessary mild steel bolts/screws complete all as specified and directed by Engr-in-charge. Note:Each Aluminium door shutter shall be fitted with provision of the following fittings: a) 01 No Aluminium door closer hydraulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg. b) )01 No Stainless steel 200mm long sliding lockable bolt c) 01 No 140mm long floor door stopper of aluminium alloy body and tongue, anodised , with hard drawn steel spring. d) Floor spring / Pivot, door handles -02

Supply only 5.5 mm thick sheet glass,ordinary quality and glazing with snap grid in squares n.exc 0.5 sq.m each pane complete all as specified and directed by Engr-in-charge.

Supply only 09 mm prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations fixed with screws to Aluminium frame work complete all as specified and directed by Engr-in-charge..

M&L Pre-cast cement concrete block of PCC 1:5:8 i.e. one part cement; five part sand and eight part stone aggregate (5 part 20 mm and 3 part 12.5 mm size stone aggregate) in masonry exceeding 10 cm in width and setting in cement mortar 1:4, complete, as specified and directed.Centre with hanger connected.

M&L rendering 10mm thick in CM 1:4 over brick or concrete surfaces complete all as specified and directed by Engr-in-charge.

M&L glazed, coloured, ceramic, tiles of size (450mm x 350 mm) or (300x600 mm) and 7 mm thick, on vertical surfaces, such as dadoe, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed by Engr-in-charge.

M & L rendering 10 mm thick in cement mortar (1:4) as in backing coat for fixing of tiles in vertical surfaces complete all as specified and directed by Engr-in-charge.

M&L for machine cut cudappa stone slab 20-25mm thick over cement screed base laid and jointed with gray cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed by Engr-in-charge.

M&L granite (of any type) 18 mm thick (table rubbed and polished) in kitchen platforms ,etc including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-charge.

M&L for preparing old plaster surfaces including complete removal of complete existing treatment washing, rubbing down and stopping of distempered and painted surfaces apply two coats of oil bound distemper over a coat of primer on wall complete all as specified and directed by Engr-in-charge.

M&L 3mm thick wall care putty on wall complete all as specified and directed by Engr-in-charge

M&L 3mm thick wall care putty on ceiling complete all as specified and directed.

M&L for preparing old plaster surfaces including washing, rubbing down and stopping of distempered and painted surfaces apply two coats of oil bound distemper over a coat of primer on ceiling complete all as specified and directed by Engr-in-charge.

S&F PVC false ceiling consisting of 600x600mm, 5mm(± 0.25) thick plain embossed PVC sheet of density 600 Kg/Cbm Manufactured by an ISO certified company, used as panel insert in a framework made using anodized aluminium T-section f sizes of 1''x1''(25x25mm,19 gauge or 1 mm thick) in square pattern of grid sizes 2'x2' (600x600mm). The aluminium framework is supported from the ceiling with the help of 'J' hook and GI wire/6mm M.S rods of required sizes to maintain proper level etc. The aluminium framework is suported on side wall with the use of aluminium L-section of size 1''x1''(25x25mm) angles complete all as specified and directed by Engr-in-charge.

S&F in repair of MS 25 mm dia Drapery curtain rods powder coated decorative type complete all as specified and directed by Engr-in-charge.

S&F in repair MS fancy powder coated brackets for 25 mm dia drapery curtain rods complete all as specified and directed by Engr-in-charge.

M&L for application of leakage/ seepage proof coating consisting of preparation of surface of exterior walls, parapet, chajjas etc with wire brush to remove all loose dirt, oil, grease etc and filling cracks more than 5mm wide with Dr Fixit Pedelite URP or with plaster seal of STP Ltd and crack less than 5mm wide Dr Fixit crack X powder or with plaster seal of STP Ltd and applying Dr Fixit primeseal primer or STP Ltd (and allow to dry/set for 08 Hours) and subsequently apply two coats of water proof decorative elastomeric coating system of approved shade/colour of Dr. Fixit Raincoat wih DFT 100 microns shade/colour or shalicry 2115 of STP ( The surface after painting one coat shall be allowed to dry at least 08 hours before next coat) through approved applicator all as per manufacturer instructions including double scaffolding etc complete all as specified and directed by Engr-in-charge.

S&F IInd class HW (Sal) plain solid & frames wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-charge..

M&L Plywood,20mm, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and directed by Engr-in-charge.

M&L decorative laminate 0.9mm type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions complete all as specified and directed by Engr-in-charge.

S&F framed stainless steel sections as in drawers and pull up cuboards, design as approved of any size and shapes including clips and washers,etc to fix it to the prelaminated PVC sheets in cabinets,etc of stainless steel grade 304, all as approved and directed during execution complete all as specified and directed by Engr-in-charge..

M&L GI push pull channels of approved brand of size 20"(51cm) legth for modular cabinets complete all as specified and directed by Engr-in-charge..

M&L stainless steel 'L' shape soft closing spring hinges for cabinet shutters complete all as specified and directed by Engr-in-charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting in hard and dense soil complete all as specified and directed by Engr-in-charge..

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-charge.

Excavation in trenches not exceeding 1.5m ;wide and n.exc 1.5m in depth for foundation etc or shafts. Wells etc not exceeding 10 Sqm on plan and n.exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed by Engr-in-charge..

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engr-in-charge.

Removing excavated material exc. Upto 5 Km out side MD land complete all as specified and directed by Engr-in-charge.

M&L Hardcore of Broken stone or boulders gauge exc 63 mm but n exc. 100 mm , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed by Engr-in-charge.

M&L Cement concrete 150 mm thick type C-2 1:3:6 (40mm graded aggregate) as in sub base complete all as specified and directed by Engr-in-charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including old tarfelt etc and removing them outside MOD Land complete all as specified and directed by Engr-in-charge.

M&L for RCC (1:2:4) grade in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-charge..

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc in finished surface complete all as specified and directed by Engr-in-charge..

M&L for mild steel CRS bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as stirrups complete all as specified and directed by Engr-in-charge.

M&L for mild steel CRS bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-charge.

M&L 40 mm thick (1:2:4 cement concrete) damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed by Engr-in-charge.

Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 Cum per sqm complete all as specified and directed by Engr-in-charge.

Cutting out bricks, forming toothing for and bonding new into old work including value of new materials entering old walls and jointing and pointing in cement mortar ( 1:4 ) complete all as specified and directed by Engr-in-charge.

M&L forming jambs, etc to openings incl cutting, toothing and properly bonding into old work also facing, jointing and pointing to match existing work complete built in CM 1:6 complete all as specified and directed by Engr-in-charge.

Making good under cills or over arches, lintels and bressummers, incl all pinning when necessary, new work built in CM ( 1:4 ) complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:3:6 type D2 using 40mm aggregate in foundations, filling and mass-concrete complete all as specified and directed by Engr-in-charge.

S&F rolled sections with ERW or Induction butt weld M.S. tube black conforming to IS 1161-1979 grade Yst 240 as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed by Engr-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge.

M&L preparation of new or previously untreated surface & applying two coat synthetic enamel Painting over a coat of preiming red red oxide zinc chrome complete all as specified and directed by Engr-in-charge.

M&L 15mm thick Screed bed / bedding in mortar 1:4 of complete all as specified and directed by Engr-in-charge.

M&L Vitrified tiles 600x600x10mm thick polished, in floors set and jointed in neat cement slurry and pointed in white or coloured to match over & including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-charge.

S&F sheet glass ordinary quality 4.50 mm thick and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-charge..

Material and Labour powder coated aluminum beads grill of 4.5 x 7.5 mm bar size and 100 mm mesh with aluminium channel fixing of aluminium frame with necessary bolt/screw, or RG 103 or equivalent complete all as specified and directed by Engr-in-charge.

S&F sheet glass ordinary quality 4.00 mm thick and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-charge.

M & L PCC (1:4:8) type D2 (40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-charge.

Taking down cement plaster on brick or stone walls or concrete surfaces etc including rakingout joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-charge.

Supply and fixing 12mm MDF boards, exterior grade, prelaminated both sides with decorative choice laminations fixed with screws to timber frame work complete all as specified and directed by Engr-in-charge.

S & F magnetic catches brass body and striking plate with aproved quality complete all as specified and directed by Engr-in-charge.

S & F continuous (Piano) hinges, stainless steel bright finish or electro galvanised width of flaps (when open) in 40mm complete all as specified and directed by Engr-in-charge.

S & F extruded aluminium alloy handles 100mm fabricated type, anodised complete all as specified and directed by Engr-in-charge.

S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished, bright finished complete all as specified and directed by Engr-in-charge.

M & L (porcelain body) coloured joint free ceramic tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-charge.

Ditto all as above but on skirtings complete all as specified and directed by Engr-in-charge..

M & L for machine cut cudappa stone slab 40mm thick over cement screed base laid and jointed with gray cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed by Engr-in-charge.

Supply and fix brass type mortice locks vertical type 75 mm size 4 levers complete all as specified and directed by Engr-in-charge.

Supply only 5 mm thick sheet glass,ordinary quality and glazing with oil putty in squares n.exc 0.5 sq.m each pane complete all as specified and directed by Engr-in-charge..

Supply only 18/19mm prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations fixed with screws to timber frame work complete all as specified and directed by Engr-in-charge..

Dismantling asbestos cement (corrugated ted, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed by Engr-in-charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed by Engr-in-charge..

M&L for 15mm bore medium grade GI tubing with all fittings fixed to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-charge..

Cutting existing steel tubing for alterations or additions (Each cut measured)Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector)f necessarily done in position without taking down complete all as specified and directed by Engr-in-charge..

M & L for 20mm bore medium grade GI tubing with all fittings fixed to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-charge..

S & F bib tap 15mm bore fancy type chroumium plated cast copper alloy screwed for iron pipe fixed in repairs complete all as specified and directed by Engr-in-charge.

S & F stop cock valve 15mm bore cast copper alloy (concealed type ) fancy type screwed down high pressure and fixed in repairs complete all as specified and directed by Engr-in-charge.

S & F in repairs wash basins, vitreous china Oval type of size 550x440mm incl cutting for and pinning in ends of brackets or recting stand including brackets and waste pipe etc complete all as specified and directed by Engr-in-charge.

S&F Pillar taps 15 mm bore chromium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed in repairs complete all as specified and directed by Engr-in-charge.

S & F PVC connection pipe 15mm bore 600mm long with brass connector complete all as specified and directed by Engr-in-charge.

S & F Low density polythylene pipes (LDPE) of pressure rating 6 Kgf/cm2 fixed to walls, floors,etc 32mm dia complete all as specified and directed by Engr-in-charge.

Cutting holes into or through brick walls built in CM (superficial area exc 400 sq.cm but not exc 0.10 sq.m) complete all as specified and directed by Engr-in-charge.

S & F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints , laid in trenches / floors or fixed to walls complete all as specified and directed by Engr-in-charge.

S & F 75 mm bore PVC (SWR) bends complete all as specified and directed by Engr-in-charge.

S & F 75 mm bore PVC (SWR) bends provided with access door complete all as specified and directed by Engr-in-charge.

S & F cast iron 100 mm dia spun waste pipe in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed by Engr-in-charge.

S & F 500 Ltrs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all complete all as specified and directed by Engr-in-charge.

S & F ball valve high pressure of PTMT with eppoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed,( min wt 210 gms) complete all as specified and directed by Engr-in-charge.

M & L for preparation of new steel surfaces of any description over 10 cm in width or girth not otherwise described and apply two coats synthetic enamel paint of over a coat of red oxide primer complete all as specified and directed by Engr-in-charge.

M & L preparation of newly plastered surfaces & applying two coat of weather coat paint over one coat of primer complete all as specified and directed by Engr-in-charge.

M & L for preparing old painted surfaces of walls including washing, rubbing down and stopping of distempered and painted surfaces, applying two coats of plastic emulsion paint over a coat of primer complete all as specified and directed by Engr-in-charge.

M & L PCC (1:3:6) type C1 (20mm graded stone aggregate) as in coping including necessary use and waste of formwork. complete all as specified and directed by Engr-in-charge.

Providing reinforced cement concrete slabs supported on walls, (1:2:4) in cover slab (for manholes etc) and similar articles with plain faces including chamfers, weathering, throating complete all as specified and directed by Engr-in-charge.

Use & waste of formwork for slabs & similar work complete all as specified and directed by Engr-in-charge.

Providing precast cement concrete (1:2:4) (20 mm graded aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM (1:4) complete all as specified and directed by Engr-in-charge.

S & F Mild steel deformed or twisted CRS bars 5mm dia and over upto and including 10 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips as in stirrups, spacers and binders complete all as specified and directed by Engr-in-charge.

M & L for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engr-in-charge.

S & F anodised aluminium snap grid frame work for false ceiling complete all as specified and as directed.

Providing and fixing Gypsum Board 10mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engr-in-charge.

Cutting opening through brick walls for door , window and other opening or enlarging existing openings, converting window into door opening etc or cutting out defective brick work for under-pinning , including providing , fixing and removing shoring , cleaning and stacking bricks removing surplus serviceable bricks , from site and rubbish not exc 50 metre complete all as specified and directed by Engr-in-charge.

M&L brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engr-in-charge.

M&L for 15 mm thick cement plaster on brick or concrete surfaces in CM ( 1:4 ) mixed with water proofing compound @ 3% by weight of cement finished fair and even complete all as specified and directed by Engr-in-charge.. [ Note :- WPC shall be measured and paid separately ]

Material and labour for rendering 12 mm thick cement plaster in CM(1:6) fnished fair and even complete all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatment on walls and appying 3mm thick wall care putty finished even and smooth .Thereafter applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by Engr-in-charge.

M & L for preparation of new surfaces on walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by Engr-in-charge.

M&L for preparing old plaster surfaces of walls including washing, rubbing down and scraping of painted surfaces, in any position and applying two coats of external weather coat emulsion paint over a coat of weather coat primer all as per manufacturer's instr and directions including scaffolding complete all as specified and directed by Engr-in-charge.

Rubber gasket for aluminium frame for windows, Ventilators etc complete all as specified and directed by Engr-in-charge.

S & F in stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.14 mm fixed with stainless steel wire staple complete all as specified and directed by Engr-in-charge.

S & F 3 mm thick sheet glass ordinary quality and glazing in square not exc 0.50 Sqm each in each pane complete all as specified and directed by Engr-in-charge.

S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge & similar work, fixed with self tapping screws complete all as specified and directed by Engr-in-charge.

M & L for aluminium alloy, anodised door bolt with hasp and staple ( bolt type) and fixing clips of sheet, or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed for 200 mm long bolt complete all as specified and directed by Engr-in-charge.

Dismantling carefully , timber scantling framed work in fillets, rails, posts, rafters, purlins, etc. under 40 sq cm in section complete all as specified and directed by Engr-in-charge.

M & L for Plain cement concrete in 1:2:4 ( 20 mm graded stone aggregate ) in coping , bed blocks and similar works with and including use and waste of formwork complete all as specified and directed by Engr-in-charge.

Supply and fixing , Fe - 290 ( Gde E- 165 ) in roof trusses ( framed ) , trussed, purlins , crane gantries , rails and fastenings and heavy bracket framing (Beam , tee, angle, channel or flat sections ) including distance pieces , cleats etc complete all as specified and directed by Engr-in-charge.

Dismantling carefully of wall and ceiling boards ( fibre ,pulp, insulation,etc,) or insulation boards/slabs/blankets any thickness,including cover fillets complete all as specified and directed by Engr-in-charge.

Taking down shutters without taking off shutters from frame exc 1.50 Sqm but not exc 4 Sqm each complete all as specified and directed by Engr-in-charge.

S & F factory made PVC Solid PVC door frame of size 50mm x 95mm made out of 5mm Plain colour PVC sheet reinforced with M.S. tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engr-in-charge.

Cutting holes into or through brick wall built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed by Engr-in-charge.

S & f for flat iron hold fast for door frames complete all as specified and directed by Engr-in-charge.

S & F aluminium anodised barrel tower bolts of extruded section of length 150 mm complete all as specified and directed by Engr-in-charge.

S & F stainless steel butt hinges medium weight SS of size 100 mm by complete all as specified and directed by Engr-in-charge.

S & F aluminium extruded alloy handles fabricated type anodised of size 150 mm complete all as specified and directed by Engr-in-charge.

Re-securing or easing and adjusting without taking down shutters of size exc 1 sqm but not exceeding 2.50 sqm each complete all as specified and directed by Engr-in-charge.

S & F 20 mm dia aluminium anodised tubular curtains rod with powder coated including taking down old curtain rod complete all as specified and directed by Engr-in-charge.

S & F aluminium anodised brackets powder coated to match with rod for curtain rod of 20mm dia complete all as specified and directed by Engr-in-charge.

Taking down carefully point wiring of any type (i.e. on wooden batten, surface conduit, casing capping or concealed conduit) complete wiring for power point ,bell point ,two point,ligth/fan point with fittings & fixtures such as ceiling rose, holders, switches, sockets, bell push, two switch , conduit etc. including accessories, excluding light fittings including making good disturbed surface to match the existing surface complete all as specified and directed by Engr-in-charge.

M&L for point wiring with PVC insulated, PVC unsheathed FR cable 1100 V grade , single core, stranded, copper conductor cable 1.5 sqmm size, drawn into including stove enamelled steel conduit (ISI marked) medium grade not less than 20mm dia with all conduit accessories in concealed and including PVC unsheathed FRLS cable 1.5 sqmm stranded copper cable (green insulation) for continuous earth wire and including pressed steel concealed terminal boxes of required size, covered plastic laminated bakalite sheet, ISI marked complete all as specified and directed by Engr-in-charge. (a) One light point or fan point/Exhaust Fan controlled by one switch

Same as above but (b) One point for socket outlet 5 amp same board complete all as specified and directed by Engr-in-charge.

Same as above but (c) One 3 pin socket outlet, 5 amps, independent complete all as specified and directed by Engr-in-charge.

All as per item above but 3 pin 15 Amp socket outlet point controlled by one switch using 2.5 sqmm FR copper conductor cable with continuous earth wire of 2.5 sqmm FR copper conductor on independent board complete all as specified and directed by Engr-in-charge.

S&F Switch flame proof rotary type with termination box in LM6, 6A, single pole 250V AC,single pole, one way complete all as specified and directed by Engr-in-charge.

S&F Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P + earthsocket complete all as specified and directed by Engr-in-charge.

S&F ceiling rose, surface type, bakelite 65x50mm three terminal complete all as specified and directed by Engr-in-charge.

Supply & fix fan step regulator, electronic type watt, 230 volts, AC complete all as specified and directed by Engr-in-charge.

S&F switch piano flush type, 6 amps, 230V AC,single pole, one way complete all as specified and directed by Engr-in-charge.

S&F switch piano flush type,16 amps, 230V AC,single pole, one way complete all as specified and directed by Engr-in-charge.

Supply & fi in repairs CMRI Certified LED Flameproof 1X16W LED Tube Light fixture luminaire 240 volts AC complete with all accessories and fixtures incl fixing on wall / ceiling with FRLS wiring complete all as specified and directed by Engr-in-charge. Cat Part Crompton EXTN1LT8-16/20 or equivaltent

M&L in repair for Three single core (submain) PVC insulated FR cable with 2 X 6 sqmm nominal cross sectional area stranded copper conductor and one single core green PVC insulated FR cable 4 sqmm stranded copper conductor earth continuity cable drawn through non metallic rigid PVC conduit of suitable size including all conduit and fixing accessories, concealed in wall including cutting chases or as required surface conduit/existing conduit and making good disturbed surface to match complete all as specified and directed by Engr-in-charge.

S&F MCB in repair single pole, 6 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & connection complete all as specified and directed by Engr-in-charge. (Make: Legrand Cat Part No. 603233 to 37 or equivalent Make of Seimens/ABB)

S&F MCB in repair single pole and Neutral 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & connection complete all as specified and directed by Engr-in-charge. (Make: Legrand Cat Part No. 603254 or equivalent Make of Seimens/ABB

S&F triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB 20 Amps complete all as specified and directed by Engr-in-charge.

Supply and Fix ceiling fan 1200 mm sweep 5 star rating, 230 Volt complete with hanging arrangement including down rod and fan regulator complete all as specified and directed by Engr-in-charge. .

Supply and install high speed split units indoor & outdoor units complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2.of capacity 1.5 TR operating at 230 V 50 HZ supply complete all as specified and directed by Engr-in-charge..

S&F single pole and neutral enclosure with a two pin and earth and metal clad plug socket complete with one single pole MCB 25 Amp 240 Volts complete all as specified and directed by Engeer in Charge

M&L for Sub Main wiring with two single core 4 Sqmm PVC insulated FR multistranded flexible copper conductor cable 660/1100 volts grade drawn in through flexible non metallic PVC Concealed conduit/Surface with and including PVC insulated 2.5 Sqmm single core single strand copper conductor as continuous earth wire in green colour connected to common earth dolly complete all as specified and directed by Engr-in-charge.

S&F triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB 32 Amps complete all as specified and directed by Engr-in-charge.

Supply & fix Socket outlet 2 in 1, 5 pin 5 or 6 Amps complete all as specified and directed by Engr-in-charge.

Supply & fix Socket outlet multipurpose 6 pin, 15/16 Amps, flush type, controlled by one paino switch, 230 volts,(ISI Marked) complete all as specified and directed by Engr-in-charge.

S&F Dust and vermin proof powder coated MCB Distribution board (DB), double door type made out of sheet metal enclosure ( CRCA sheet) dust and vermin proof DB,SPN 8 Way with 200 Amps rated copper busbar,250 volts earth bar IP 43 protection, flush to wall complete all as specified and directed by Engr-in-charge.

S&F Dust and vermin proof powder coated MCB Distribution board (DB), double door type made out of sheet metal enclosure ( CRCA sheet) dust and vermin proof DB,SPN 4 Way with 200 Amps rated copper busbar,250 volts earth bar IP 43 protection, flush to wall complete all as specified and directed by Engr-in-charge.

Supply and fix wall mounted fan AC single phase 230/ 240 V of size 400 mm sweep with all connected items complete including connection with 3 core copper flexible wire from switch socket to fan,including provn of fan fixing nut bolts complete all as specified and directed by Engr-in-charge.

Cutting, chasing and making holes into or through brick walls/stone machinary wall suitable for fixing exhaust fan of size 450 mm sweep and making good all the disturbed surfaces of the wall with cement mortar complete all as specified and directed by Engr-in-charge.

Supply and fix heavy duty exhaust fan AC single phase 230/ 240 V of size 450 mm 1400 RPM sweep with louvre complete all as specified and directed by Engr-in-charge.

S&F LED batten single tube of 1X20 W(4 feet long) 230 V,6000K rated CCT energy efficient with atomic ballast bipin holders starter blocks,diffusers etc complete with all accessories internally pre wired and including connecting up with twine core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engr-in-charge.

S&F LED wall spot light provided with high output 5W wall/ceiling mounted 230V etc complete with all all accessories internally pre wired and including connecting up with twine core twisted flexible copper conductor cable with suitable size all as specified and directed. Make:- Bajaj, C&S, Philips

S&F in Repairs LED Light luminaries Square (2x2 ft) type 36W suitable suitable for Modular/pop/Gypsum ceiling with starter, connector block, etc,complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible conductor of copper with PVC square blocks of size 600mmX600mm for fixing the fitting complete all as specified and directed by Engr-in-charge. Make -:Cat NO-LCTLS-36-CDL of Crompton or equivalent

M&L for MCB Single pole & neutral 230 Volts B-Curve 10 KA,6-32 Amps Capacity IP 20 complete all as specified and directed by Engr-in-charge.

M&L for Sub Main wiring with two single core 4 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade drawn in through rigid flexible non metallic PVC concealed conduit with and including FRLS insulated 1X2.5 Sqmm single core multi strand copper conductor as continuous earth wire in green colour connected to common earth dolly complete all as specified and directed by Engr-in-charge. Note:- 1. Two runs of cable 4 sqmm and one run of 2.5 earth wire incl PVC conduit will be measured and paid one unit. 2. Separate sub main wiring will be run for each accn.

Earthing complete with copper earth plate electrode 600mm x600 mm x 6mm buried directly in ground vertically to a depth not less then 2.25 meter below normal ground level with top edge of the plate not less then 1.50 meter below normal ground level connected to copper earth 20 x3 mm copper strip by means of bolts ,nuts ,check nuts and washers complete up to and including test point made out of20 x 3 mm copper flat including earthing pit , charcoal common salt,Earthing lead 20 x3 up to 7.5m, 20mm dia medium grade GI watering pipe, PPC pit in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate ,PCC pit cover including earth work complete all as specified and directed by Engr-in-charge. NOTE-: Copper earth strip beyond 7.5 m & GI protection pipe shall be measured and paid for separately under relevant item of schedule .

S&F MCCB TPN 160 Amps , 415Volts, 25KA , L&T CAT NO-CM90634OOMO/ LEGRAND CAT NO-420057 / ABB complete all as specified and directed by Engr-in-charge.

S & F MCCB DB VERTCLE TYPE made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, IP-43-IK09 protection grade , 415Volts TPN with 4 way Double door , L&T CAT NO-DBVTH004DD/ / LEGRAND CAT NO-607913/ ABB complete all as specified and directed by Engr-in-charge.

Supply and fix UV filter having purification technology of UV+RO, of model Aqua Grand Aqua-RO+UV+MI and Auto TDS control (with 10stage) Electronic water purifier(White) of product code HOMAQUA-GRAND-ACHEA26456C57ED02F with 9 litr capacity complete all as specified and directed by Engr-in-charge.

S&F electric chimmney of air suction capacity 1200Cum per hour consumes 360 watt of dimention width(mm) 600 depthmm 480 with all other accessories decorative type complete all as specified and directed by Engr-in-charge.

M& L for GI ducting for Chimney complete all as specified and directed by Engr-in-Charge

R J ENTERPRISES