REPAIRS TO LOW TENSION EXTERNAL ELECTRIC SUPPLY AND OTHER ALLIED WORKS FOR MH AND 100 ORs QTRS AND DEFENCE COLONY MD ACCN REPAIRS AND MAINT OF INTERNAL ELECTRIC SUPPLY AND OTHER ELECTRIFICATION WORKS AT INSIDE OTA CHENNAI UNDER GE STM

Amount

Taking down the unserviceable point wiring of lights, fans, scokets complete including switches, switch sockets outlets, fan regulators, lamp holder, ceiling rose, etc excluding light fittings and depositing where directed and making good the disturbed surfaces to match with the existing surface.

Taking down the existing unserviceable MCB DB along with MCBs of any type and capacity and depositing where directed and making good the disturbed surface to match with the existing surface.

M&L for Point Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable FRLSH 1100 volts grade, multistranded with copper conductors conforming to IS specifications, with colour code drawn through and including non metallic rigid PVC conduit, PVC conduit fittings and conduit accessories or casing capping incl accessories fixed on wall / ceiling or concealed on wall and fixed on ceiling etc with suitable clamps, screws, etc or concealed in wall including cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 for concealed conduit wiring and making good the disturbed surfaces, matching with the existing wall surfaces, cutting not exceeding 10 cm girth, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly all as specified and as directed :-

One light point controlled by one switch

One fan point controlled by one switch and one regulator

One 3 pin 5 Amps switch socket on independent board

One 3 pine 5 amps switch socket on same board along with other switches.

One bell point controlled by bell push switch on independent board.

All as per item No 3 herein before but with 2.5 Sqmm single core PVC cable for one 3 pin 15 amps switch socket outlet on independent board.

M&L for sub main wiring with PVC insulated, 1100 volts grade single core FRLSH multistranded copper conductor cable conforming to IS specifications, 2 runs of 10 sqmm including one run of 10 sqmm single core multistranded copper conductor PVC insulated cables as earth continuity conductor with colour code drawn through and including one run of 25 mm dia rigid PVC conduit and conduit accessories or casing capping incl accessories fixed on wall/ceiling etc, or concealed in wall and connecting to common earth dolly including taking down old unsv all as specified and directed.

All as per item No 5 herein above but with 2 runs of 6 Sqmm and one run of 1x 6sqmm earth wire in PVC conduit as specified and as directed.

All as per item No 5 herein above but with 2 runs of 4 Sqmm and one run of 1x 4 sqmm earth wire in PVC conduit as specified and as directed.

All as per item No.5 herein above but with 2 X 2 .5 sq. mm + 1 X 2.5 sq. mm earth wire in PVC conduit or casing capping as specified and as directed.

All as per item No.5 herein above but with 2 X 1.5 sq. mm + 1x1.5 sq.mm earth wire in PVC conduit or casing capping as specified and as directed.

All as per item No.5 herein above but with 4 runs of 10 sqmm and one run of 2 x 10 sq.mm earth wire in PVC conduit as specified and as directed. Note for item Nos 3 to 10 :- (a) The wiring shall be done in proper colour coding using red, yellow and blue for phase, black for neutral and green for earth leads. (b) For concealed wiring wherever required cutting chases will be measured separately under relevant items.

Supply and Fix in repairs LED post top lantern made in cast aluminium spigot housing with decorative clear opal acrylic diffuser and IP65 protection complete all as specified and as directed. Make:- Bajaj Cat No BGCT 24 LED WW/ Crompton Greaves Cat No LBLA1-10-CDL or equivalent

Supply and Fix in repairs Ceiling rose surface Bakelite 65mm x 50 mm two to three terminals all as directed.

Supply and Fix in repairs Switch piano flush type 5 amps single pole, one way, 240 Volts all as directed.

Supply and Fix in repairs Switch socket outlet 3 pin, 5 amp, flush type all as directed.

Supply and Fix in repairs Socket outlet 3 pin 5 Amps flush type all as directed.

Supply and Fix in repairs Bell push flush type 5 amps single pole 240 Volts all as directed.

Supply and Fix in repairs Buzzer, AC, 230 volts, single pole all as directed.

Supply and Fix in repairs Bell ding dong, AC, 230 volts, single pole all as directed.

Supply and Fix in repairs Bell Musical type all as specified and as directed.

Supply and Fix in repairs Socket outlet 3 pin 15 amps flush type all as directed.

Supply and Fix in repairs Switch socket outlet multipurpose 3 pin, 15 amp and one pin, 5 amp controlled by one switch all as directed.

Supply and Fix in repairs stepped type electronic fan regulator flush type on the exiting phenol laminated sheet extra as required.

Supply and Fix in repairs Modular Switch Roma flush DIRECT TO FIT press type 10 amps single pole, one way, 240 Volts all as per site requirement complete all as specified and as directed.

Supply and Fix in repairs Modular Switch Roma flush DIRECT TO FIT press type 16/20 amps single pole, one way, 240 Volts all as per site requirement complete all as specified and as directed.

Supply and Fix in repairs Modular Socket Roma flush DIRECT TO FIT press type 10 amps single pole, one way, 240 Volts all as per site requirement complete all as specified and as directed.

Supply and Fix in repairs Modular Socket Roma flush DIRECT TO FIT press type 16/20 amps single pole, one way, 240 Volts all as per site requirement complete all as specified and as directed.

Supply and Fix in repairs PVC Gang box surface type suitable for fixing of 5 pin 15 Amp multipurpose switch socket on wall complete all as specified

Supply and Fix in repairs PVC Gang box surface type suitable for fixing of 5 pin 5 Amp multipurpose switch socket on wall complete all as specified

Supply and fix in repairs Lamp holder insulated body complete all as specified and as directed.

Supply and fix in repairs Modular Fan step regulator, 120W - 1 module for ceiling Fan of 1200 mm sweep all as specified and as directed.

Supply and fix in repairs Modular white cover with plate with frame 2 module incl matching with white cement wk if necessary

S&F in repairs Modular white cover with plate with frame 3 module incl matching with white cement wk if necessary

S&F in repairs Modular white cover with plate with frame 4 module incl matching with white cement wk if necessary

S&F in repairs Modular white cover with plate with frame 6 module incl matching with white cement wk if necessary

S&F in repairs Modular white cover with plate with frame 8 module incl matching with white cement wk if necessary

S&F in repairs Modular white cover with plate with frame 12 module incl matching with white cement wk if necessary

S&F in repairs Modular white cover with plate with frame 16 module incl matching with white cement wk if necessary

Supply and fix in repairs Modular flush box 1/2 module

Supply and fix in repairs Modular flush box 3 modules

Supply and fix in repairs Modular flush box 4 modules

Supply and fix in repairs Modular flush box 6 modules

Supply and fix in replacement of metal clad socket single pole and neutral enclosure with a two pin and earth plug top and socket complete with one single pole MCB 230 Volts 20/32 Amps complete all as specified and as directed.

Supply and fix in repairs MCCB Distribution board, TP&N, vertical, double door, sheet steel, enclosure powder coated with 100 Amps rated bus bar with neutral link,415 Volts 4 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete including 4 Pole V-Tec MCCB of 100A rating & 16kA breaking capacity, MCCB pre-fitted at factory all as specified and directed.

Supply and fix in repairs MCCB Distribution board, TP&N, vertical, double door, sheet steel, enclosure powder coated with 100 Amps rated bus bar with neutral link, 415 Volts 8 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete including 4 Pole V-Tec MCCB of 100 A rating & 16kA breaking capacity, MCCB pre-fitted at factory all as specified and directed.

Supply and fix in repairs MCCB four pole, 415 Volt, 63 Amps, 16 KA, adjustable thermal & fixed magnetic setting complete all as specified and directed.

Supply and fix in repairs MCCB four pole, 415 Volt, 100 Amps, 16 KA, adjustable thermal & fixed magnetic setting complete all as specified and directed.

Supply and fix in repairs MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated bus bar with neutral link, 4 ways SPN Double door, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Supply and fix in repairs MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated bus bar with neutral link, 8 ways SPN Double door, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Supply and fix in repairs MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated bus bar with neutral link, 12 ways SPN Double door, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Supply & Fix in repairs MCB Four pole 415 volts, 40 to 100 amps 'C' Curve 10 kA Capacity all as directed.

Supply and fix in repairs MCB SPN, 240 Volts, 32 to 63 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed

Supply and fix in repairs MCB SP, 240 Volt, 6-32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed

Supply and fix in repairs 40W LED aluminium battens high wattage decorative ultra slim polycarbonate LED lighting fixture with high lumen output, environmental friendly, energy efficient complete all as specified and as directed. Make : Havells Cat No LED Pride plus LHEXACP7IN1J040/Bajaj Cat No BPTX 40W LED 4F WH/Crompton Greaves Cat No CCS-100-40-65-HL2-DP-NWH

Supply and fix in repairs 30W LED PC battens high wattage decorative ultra slim polycarbonate LED lighting fixture with high lumen output, environmental friendly, energy efficient complete all as specified and as directed. Make : Havells Cat No LED Pride Plus LHEXAWP7IN1W030/Crompton Greaves Cat No TCS-104-10-65-SL-DP-NWH

Supply and fix in repairs 10W LED battens decorative ultra slim square profile LED lighting fixture with extruded polycarbonate environmental friendly energy efficient complete all as specified and as directed. Make: Havells Cat No LED Pride Plus LHEXACP5IN1W010/Bajaj cat No BCLSB 10 WH or equivalent

Supply and fix in repairs of surface mounted 24W led luminaries of 2'x2' complete all as specified and as directed. Make: Havells LHEAABP71N1W024/Bajaj Cat No BGSLO SLEEK 15 WH SQ/Crompton LCTLRP-42-FO-CDL (2X2)

Supply and fix 30W bldg security light fitting including suitable GI bracket and clamps nuts etc with best in class design and robust heat sink along with class leading IP, and surge protections for long lasting performance complete all as specified & directed. Make: Havells Cat No LHETAVU7PA70030/Bajaj Cat No BCLST 30W LED/ Crompton Greaves Astra Neo Cat No LSTS-30-CDL/NL-M

Supply and fix surface mounted LED panel PDC aluminium housing and high translucent diffuser makes it a luminaries efficiency 100 Lm/W & 120 lm/W complete all as specified and as directed. Make: Crompton Cat No LCDSPLN-R-CG-19 CDI/Bajaj Cat No BGSLO Sleek 18W WH RD or equivalent

Supply and fix bulk head fitting PDC housing LED luminaries with opal diffuser, equipped with 2 KV in-built surge protection with IP 65 protection rating including taking down old unsv light fitting complete all as specified and as directed. Make: Bajaj Cat No BIBWP 10W LED/Crompton CIS-306-10-57-SL-DP-NBK or equivalent

Supply and fix decorative wall mounting brushed nickel finish fixture with opal glass diffuser suitable with 9W LED lamp B22 base including taking down old unsv light fitting complete all as specified and as directed. Make: Havells Cat No LHFOAJE1TZ11060 or equivalent

Supply and fix decorative wall mounting brushed nickel finish fixture with opal glass diffuser suitable with 2x9W LED lamp B22 base complete all as specified and as directed. Make: Havells Cat No LHFOAJE1TZ11060 or equivalent

Supply and laying in repairs of 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed twin core 4 sq. mm nominal cross section in service connections.

Supply and laying in repairs of 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed twin core 6 sq. mm nominal cross section in service connections.

Taking down ceiling fans/Exhaust/wall fan of any size, any make , model, dismantling blades for repair/servicing /replacement of parts/rewinding and refixing the same after replacement of spares and parts servicing/ rewinding complete all as specified. Note: spare parts and rewinding and servicing shall be measured separately

Ball bearing for ceiling fan/Exhaust fan/Wall fan/Pedestal fan upto 1400mm sweep.

Bush bearing for ceiling fan/Exhaust fan/Wall fan/Pedestal fan upto 1400mm sweep.

Fan condenser capacitor 2.5 mfd.

Down rod 15 mm dia medium grade including cutting required length, drilling holes, painting complete.

Fan blade of existing model/Make/Type for upto 1400 mm sweep

Shaft assembly including lath works complete for ceiling fan/Exhaust fan/Wall fan/Pedestal fan upto 1400mm sweep

Copper winding wire suitable gauge

Taking Down and refixing incl painting of water heaters (Geysers) upto 2.0 KW (50 Litres) of following capacity of any make /model in site with synthetic enamel paint by brush including filling of cavities with fillers one coat after cleaning all dust etc including writing MES numbers etc all as specified and directed. Note : spare parts and servicing shall be measured separately

Heating element 1.5 KW capacity AC 230 V and conforming to IS specifications screw/flange type.

Heating element 2.0 KW capacity AC 230 V and conforming to IS specifications screw/flange type.

Thermostat suitable for water heater upto 50 litres capacity.

Indicator lamp any type suitable for water heaters upto 50 litres capacity.

Non return valve 15 mm dia size.

PVC connections with brass check nuts 15 mm dia x 45 cm long for hot water supply and cold water supply.

Plug top 3 pin 15 amps.

Rubber gasket flat/'O' ring type suitable for water heater

PVC cable 3 core flexible copper conductor cable of size 40/0.193

Pressure release Valve suitable for geysers upto 50 litres capacity.

Removing the old rusted /worn out MS bolts and nuts and grouting 4 nos new MS "T" bolts and nuts in brick walls (MS bolt size 3/8 " x 6" with washers) for geyser (Water Heater) of any Capacity/ model and making good the disturbed surfaces incl plastering, curing etc all as directed.

Material and labour for earthing complete with galvanised steel earth plate electrode 60x60cmx 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point all as specified or indicated including testing on completion all as specified and as directed

Labour only for attending and identifying electric supply complaints no lights and day to day maintenance of existing switch board, DB's, LT Panels including connecting electrical accessories/ spares of elect supply installations, electrical fitting with lights, short circuits in any OTM/Md accn/Pump house as per complaint register complete all as specified & directed.

(Note for Ser No 67):- (i) The quoted rate shall deemed to be including the cost of labour involve under repaired item. (ii) The complaints shall be attended and the defects shall be rectified by a team of experienced electrician as applicable assisted with adequate number of helpers as directed by Engineer-in-charge but minimum provision of executing team are as under :- 1. Electrician ( semi-skilled)- 02 Nos 2. Helper (un-skilled) for electrician - 01 No (iii) Engineer-in-charge may decided to depute team per day to complete the complaint within 08 hours. Per day execution of complaints shall be measured and paid under item No 67. (iv) All T&P required for attending the complaints shall be provided by the contractor without any extra cost of govt. (v) The Electrician shall always in possession of all Electrician tools, LT Megger, Earth Tester, Multimeter, Crimpling tool, insulation tape, Hand gloves, Ladders etc required at site. (vi) Noting of the complaints in complaint register complete all as specified and directed. (vii) Contractor will submit group insurance of deputed employees from any authorised Govt Agencies.

Excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation of stays & Poles, laying of cables etc and getting out in soft / loose soil all as specified and directed.

Returning, filling in, using excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25 cm using excavated soil all as specified and directed.

Removing excavated material/ surplus soil not exceeding 50 metres and depositing where directed at a level not exceeding 1.5 metre above the starting point all as directed.

Supply, lay/spread in trenches, sieving sand including cleaning, spreading, levelling, punning for laying /cushioning of cable all as specified and as directed. Note: Punned thickness shall be measured and paid.

Supplying and laying burnt Fly ash bricks class standard old size for protection of cable as directed.

M&L for plain cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate for coping to the poles with finishes with out using extra cement.

Disconnecting and taking out the old unserviceable LT UG cable in trenches, wall & poles and taken as credit including supply and Laying in trenches / poles / wall etc LT UG Cable XLPE insulated, armoured, heavy duty with multistranded aluminium conductor, 1100 volts grade conforming to IS specifications and of the following sizes:- Note: Lugs and glands are deemed to be included in the rate quoted for laying of cable and to be used wherever required while connecting cables to the panel board. Earth work such as excavation, refilling etc, shall be measured and paid separately under relevant item:-

(a) LT UG cable 4 core 10 sqmm

(b) LT UG cable 4 core 16 sqmm

(c) LT UG cable 4 core 25 sqmm

(d ) LT UG cable 3.5 core 35 sqmm

(e) LT UG cable 3.5 core 50 sqmm

(f) LT UG cable 3.5 core 70 sqmm

(g) LT UG cable 3.5 core 95 sqmm

(h) LT UG cable 3.5 core 120 sqmm

(j) LT UG cable 3.5 core 185 sqmm

Re- laying only ( where directed at site) in trenches and connecting with suitable size of cable jointing kit/lugs/ thimble etc. serviceable under ground cable retrieved from Srl item No - 75.01 to 75.09 above of following sizes:- Note:- Cable jointing kit will be measured & paid separately under relevant items of Sch 'A'.

(a) LT UG cable 4 core 10 sqmm

(a) LT UG cable 4 core 16 sqmm

(b) LT UG cable 4 core 25 sqmm

(c ) LT UG cable 3.5 core 35 sqmm

(d) LT UG cable 3.5 core 50 sqmm

(e) LT UG cable 3.5 core 70 sqmm

(f) LT UG cable 3.5 core 95 sqmm

(f) LT UG cable 3.5 core 120 sqmm

(f) LT UG cable 3.5 core 185 sqmm

S&F Straight through joints (epoxy) heat shrink type for underground cable including joint kits and labour complete for making joints suitable for LT PVC sheathed / armoured heavy duty cables with aluminium conductor of following sizes :-

(a) LT UG cable upto 4 core 16 Sqmm

(b) LT UG cable 3.5/4 core 25 sqmm to 50 sqmm

(c ) LT UG cable 3.5 core 70 to150sqmm

(d) LT UG cable 3.5 core 185 to 300 sqmm

Taking down the old unserviceable junction box and taken as credit including S&F Junction box PVC (FRP) Junction boxes weather proof type with hinged type door off white colour of size 280x145x100mm with three pole connector and 1 No neutral link complete fixed on pole with suitable clamps, bolts and nuts with 6A MCB and fixing arrangements all as specified and directed.

S&F in replacement power factor control relay (APFC) 12 step including necessary electric connections and testing including dismantling unserviceable power factor control relay from the panel boards, complete all as specified and directed.

Supply and fix in replacement of 230 Volt Control relay ,all as directed.

Supply and in replacement Contactor suitable for 15 KVAR 415 Volt, 3 phase including necessary connections compete all as specified and as directed.

Supply in replacement Contactor suitable for 5 to 10 KVAR 415 Volt, 3 phase including necessary connections compete all as specified and as directed.

Dismantling unserviceable power factor improvement capacitor of various capacities and Supply and fix heavy duty Cylindrical capacitors AC 440 volts, 50 Hz, Delta connection new power factor improvement capacitor of following capacities complete all as specified and directed.

(a) 25 KVAR Capacity

(b) 20 KVAR Capacity

(c ) 15 KVAR Capacity

(d) 10 KVAR Capacity

(e) 5/ 3/ 2 KVAR Capacity

M&L for removing the existing street light fitting of any type & make and Supply & installation of new street light fittings,60W LED 5700K New generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 roadway luminaries with high power LED as light source in the existing pole duly wired complete all as specified and directed.

M&L for dismantling and taking down the existing street light fitting led type for repair and replacing the unserviceable LED driver with new upto 100W LED 5700K and refixing the same in the existing pole duly wired complete all as specified and directed.

M&L for removing the existing street light fitting of any type & make and Supply & installation of new 90 W LED 5700K New generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 roadway luminaries with high power LED as light source in the existing pole duly wired complete all as specified and directed.

Removing the existing Gate light & Supply and installation of new 40W LED 5700K New generation Post top energy saving & environmental friendly long life versatile spun aluminium IP66 roadway luminaries with high power LED as light source and connecting in the existing cable complete all as specified and directed.

Removing the existing unserviceable bollards light & Supply and installation of 15W LED Bollard light TLLUM series, IP 65 rating, 3000K warm white, 4 KV surge protection, Total Harmonic Distortion <10%, Impact Protection IK07, Colour Rendering Index (CRI) >70, out door luminaries, New generation energy saving & environmental friendly long life aesthetically designed aluminium land scope luminaries for diffused lighting with high power LED Bollards as light source and connecting in the existing cable complete all as specified and directed. Make: Bajaj cat part No.BAJAJ TLLUM 15W 30K 80 C3 MS S or equivalent

Supply and laying 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed 3 core 2.5 sq.mm nominal cross section in service connections/street light connection from junction box to street light fittings.

Removing the existing unserviceable flood lights from high mast poles and supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

Supply and fix time switches 250 V single Phase of 20 Amp rating with contactor fitted inside steel enclosure all as specified and directed

S&F MCCB 3 pole 400 Amps,415 volts with rupturing capacity 35 KA. All as specified including taking out old one.

S&F MCCB 3 pole 250 Amps,415 volts with rupturing capacity 25KA. All as specified including taking out old one

S&F MCCB 3 pole 125 Amps,415 volts with rupturing capacity 16KA. All as specified including taking out old one

S&F MCCB 3 pole 63 Amps,415 volts with rupturing capacity 16 KA. All as specified including taking out old one.

Preparation of old surface and painting of steel tubular electric poles above coping level including brackets, clamps etc with good quality silver paint (two coats) complete including writing pole no and all as specified and directed.

Finding and rectification of electrical fault by Checking of external/internal(LT) elect supply feeder, street light feeder, OH conductors /under ground cables using elect tools, equipments and safety devices after arranging elect shut down of feeders from sub station to remove elect faults like tightening of loose connection, removing of any electric short,meggring of cable, excavation of soil for removing of faulty cable on a particular span and relaying of cables after removing of fault, re-tightening of cable lugs etc all as required at site and as directed. Note:- (i) The electrician employed for the purpose will be highly skilled along with one mate and should have all necessary tools and safty devices. (ii) Any major materials used for rectification of faults like Cables,MCB/MCCB/cable jointing kits/cables of any type etc will be measured and paid separately or supplied by department.(iii) Rate including hire of HT/LT fault Locater any other tools/equipments and Earth Work. works should be completed with in 12 hrs.

Material and labour for servicing DG Set Engine complete oil servicing, necessary replacement of below mentioned spares and servicing work for 380 KVA DG Set incl 6 months warrantee for servicing .(a) Diesel Filter (Pre+micro) - 2Nos, (b) Engine Oil filter (Spain-on type) - 2 Nos, (c) Engine Oil as required, (d) Radiator Coolant as required.

Material and labour for general oil servicing of DG Set Engine complete and replacement of below mentioned spares and servicing work for upto 62 KVA DG Set incl 6 months warranty for servicing .(a) Diesel Filter (Pre+micro) - 2Nos, (b) Engine Oil filter (Spain-on type) - 2 Nos, (c) Engine Oil as required, (d) Radiator Coolant - 1 Ltrs.

Dismantling self starter of any make from diesel engines of any make, opening up, overhauling / servicing including replacement of armature coils bushes carbon brushes, springs, screws, etc., assembling back, re-fixing and testing for genset capacity following capacity:-

(a) DG set 380 KVA

S&F fuel pump & Fuel injectors calibration charges for DG set capacity upto 380 KVA complete all as specified and as directed

S&F 'V' belt for fan / dynamo / water pumps for genset capacity upto 380 KVA

M&L for replacement of automatic voltage regulator (AVR) of armature of DG set capacity upto 380 KVA, 415 volts 3 phase 1500 RPM 50 Hz suitable make.

Material & Labour for Cutting and cleaning the tree branches around the street light poles/ /sub stn/ LT OH line conductors and maintain 2 mtr gap all around free from branches of tree and clear the site and throw away cut branches etc, to a distance exceeding 50m all as directed. Note: Span shall be measured along with the direction of OH/ LT.

M&L for preparation of old painted surfaces of LT panel/Feeder pillar box of any type outdoor/indoor including removing old paint with scrubbing and applying one coat of synthetic enamel paint of shade as per existing over a coat of red oxide primer, with electrically operated spray machine, complete all as specified and directed.

M&L for Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground all as specified and directed

M&L for Air termination, single pointed aluminium rod 12mm dia and 300mm long fixed with on suitable insulator base all as specified and directed.

M&L for Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw

Supply, install, test & commissioning LT panel out door, floor mounted/pedestal type, cubical, self supported,CPRI approved ,front and rear openable , double door hinged type with locking arrangement and slopping top canopy ,suitable ventilations on both sides with wire mesh, IP-52 protection with dust and vermin proof etc.fabricated out of 3.15 mm CRCA sheet duly powder coated with 7 tank chemical process, mounted/fixed on and including MS angle iron stand of 1.0 mtr height (50 cm above FFL and 50 cm below FFL) ,fabricated out of 50x50x6 mm thick MS angles duly painted with black enamel synthetic paint over a red oxide primer duly grouted in PCC 1:3:6 foundation, control wiring copper stranded PVC insulated FRLS cables not less than 1.5 sqmm, suitable size/capacity of copper strips for switch gear connection from main bus bar, earth bus strip of 32x6 mm size for entire length of panel ,suitable size of MS gland with gland plate and aluminium lugs/thimbles for all incoming/out going cables etc.complete all as directed and accommodating the followings:-

Supply, install, test and commission of 40 KVAR APFC panel with 100A, 25KA MCCB as incomer, outdoor type, fabricated with 3.15mm CRCA sheet mounted on 50x50x6mm MS angle, 3 phase 4 wire, 440 volts, ac, 50hz, System for permissible non- linear load 10% of capacity 40 KVAR Delta connection cylindrical capacitor 13 steps (5+5+5+5+3+3+3+3+2+2+2+1+1) with power factor controller, capacitor duty contactor including suitable foundation all as specified and directed by Eng-in-charge. Make:- Havells cat pat No.QHXTCB5080X0 or equivalent

(i) Capacitor Duty Contactor 1 KVAR - 2 Nos (ii) Capacitor Duty Contactor 3 KVAR - 2 Nos (iii) Capacitor Duty Contactor 4 KVAR - 1 No (iv) Capacitor Duty Contactor 5 KVAR - 1 No (v) Capacitor Duty Contactor 6 KVAR - 2 Nos (vi) Capacitor Duty Contactor 10 KVAR - 1 No (vii) Capacitor Duty Contactor 16 KVAR - 1 No (viii) Capacitor Duty Contactor 20 KVAR - 1 No (ix) Capacitor Duty Contactor 25 KVAR - 1 No (x) Capacitor 01 KVAR having tolerance 0% - 10% with discharge device resistor, confirmed to IS 13340 - 2 Nos (xi) Capacitor 3 KVAR having tolerance 0% - 10% with discharge device resistor, confirmed to IS 13340 - 2 Nos (xii) Capacitor 4 KVAR having tolerance 0% - 10% with discharge device resistor, confirmed to IS 13340 - 1 No (xiii) Capacitor 5 KVAR having tolerance 0% - 10% with discharge device resistor, confirmed to IS 13340 - 01 No (xiv)) Capacitor 6 KVAR having tolerance 0% - 10% with discharge device resistor,. confirmed to IS 13340 - 2 Nos (xv) Capacitor 10 KVAR having tolerance 0% - 10% with discharge device resistor,. confirmed to IS 13340 - 01 No (xvi) Capacitor 16 KVAR having tolerance 0% - 10% with discharge device resistor,. confirmed to IS 13340 - 01 No (xvii) Capacitor 20 KVAR having tolerance 0% - 10% with discharge device resistor,. confirmed to IS 13340 - 01 No (xviii) Capacitor 25 KVAR having tolerance 0% - 10% with discharge device resistor, confirmed to IS 13340 - 01 No

EVEREST ENGINEERING WORKS (BID ID -3343643)

M/S.RANGA AND CO (BID ID -3344315)

rc enterprises (BID ID -3343967)

ASHWIN ASSOCIATES (BID ID -3343637)

GOKUL ENTERPRISES (BID ID -3344396)

S.M.ELECTRICALS (BID ID -3344116)

G.JANAKIRAMAN CO (BID ID -3343999)

RK ENTERPRISES (BID ID -3344127)

LAKSHMI ELECTRICAL ENTERPRISES (BID ID -3339039)