SPECIAL REPAIRS TO SUB STATION NO.3 SERVANT QTR BLDG NOS WH-5 TO WH-9 CHAIN LINK FENCING IN DUPLEX BUNGALOW WOOD SIDE KINARA FOREST VIEW AND CERTAIN MISC WORKS AT DSSC WELLINGTON

Amount

B/R PORTION Demolition of brick work or stone / boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc and removing debris off the premises all as specified and directed.

M & L for Brickwork with subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in CM (1 : 6) complete all as specified and as directed.

Demolition of Brick tiles or terracing tiles, single layer on roofs laid, bedded and pointed in cement mortor and removing debris off the premises all as specified and directed by Engr-in-Charge.

M & L for cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) 40mm thick (average) on roof as padding/ levelling course, etc finished fair and even complete all as specified and as directed.

M & L for rendering or bedding layer in cement mortar (1:4) 15 mm thick on concrete surface , mixed with water proofing compound as per manufacturers instructions, finished even and smooth without using extra cement complete all as specified and as directed. Note: WPC shall be measured seperately.

M & L for APP modified water proofing membrane 4mm thick and weighing not less than 4.5 Kg /Sqm reinforced with non woven polyster matt black finished weighing not less than 100 gm/Sqm having softening point not less than 140 degree celcious, longitudinal tensile strength not less than 300 N/Sqcm, side lap & end lap 15cm over a coat of bitumen primer @ of 0.20 Kg/Sqm finishing with aluminium paint applied @ of 0.10 Kg/Sqm & finished all as specified and directed by Engr-in-Charge

M & L for providing cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as as in coping, cills ,string courses, apex stone, bed plates, kerbs etc., including necessary form work, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Supply only liquid water proofing compound all as specified and as directed.

S & F PVC (SWR) half rounded gutter dia 150 mm (6 Kg/ Sq cm) including angles or nozzle/ end cap and reducer droplet complete all as specified and as directed.

S & F 110 mm dia PVC (SWR ) ' T ' fixing in half rounded gutter dia 150 mm (6 Kg/ Sq cm) complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) pipes, Type 'B', single socketed in any length laid in walls and trenches complete all as specified and as directed.

PVC (SWR) bends 110 mm bore with any radius complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings n. exc 15 cm thick below or above GL or of any description and in any position not otherwise specifically provided for and removing debris off the premises, all as specified and directed.

M & L for cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) 75 mm thick, as in plinth protection, footpath and pavings, finished cement concrete surface even and smooth without using extra cement all as specified and as directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each, and removing from site, complete all as specified and as directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) exc 1.50 Sqm and n.exc 4 Sqm each, and removing from site, complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, and removing debris off the premises all as specified and directed.

M & L for use and waste of timber to side and soffits of suspended slab, shelves and similar items including edges for rough finished flat surfaces all as specified and as directed.

M & L for TMT bars 6mm to 8mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

M & L for Reinforced Cement Concrete, (1:2:4), (Nominal Mix) type B-1, (using 20mm graded stone aggregate) as in slabs, landing, shelves etc complete all as specified and as directed.

M & L for polished black Granite stone slab 16-18 mm thick as in cooking platform, shelves etc machine cut, polished and moulding the exposed edges to a uniform smooth surface, incl. grinding and polishing, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone complete all as specified and as directed

S & F 35mm thick, second class hard wood ( Sal/ Hollock), glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutter as specified in SSR Part-I Section 8, clause 8.24(a) for door shutter complete all as specified and directed by Engr-in-Charge.

M & L for 40mm thick Flush door shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to chowkats complete all as specified and as directed.

M & L for preparation of new wooden surfaces and wood based materials of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ' C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and as directed.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supply & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and as directed.

S & F aluminium, anodised, barrel tower bolts of extruded section, 150 mm long complete all as specified and as directed.

S & F 300 mm size aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed.

S & F in repairs steel locking bolts with mild steel electro galvanised plate and bright bolt not less than 10mm dia, 100mm size complete all as specified and as directed.

S & F aluminium handles, cast type, anodised of size 150 mm long, complete all as specified and as directed.

S & F pressed steel frames of size 125 x 60 mm with 1.25mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and tarring back side of frame, complete all as specified and as directed.

M & L for PCC (1:2:4) type B-0 ( using 12.5mm graded stone aggregate) as in filling of steel chowkats or frames complete all as specified and as directed.

S & F rotational moulded polythene double layered water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 500 litres capacity including dismantling water tanks and removing to store complete all as specified and as directed.

Fixing only PVC water tank 500 litres complete all as specified and as directed. Note: Serviceable water tank obtained during dismantleing shall be reused.

S & F ball valves (20 mm) high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed., (Minimum weight 20mm-210 gms) all as specified and as directed.

Taking up/down steel tubing and connections including cleaning for refixing or removal to store 15mm/20mm bore pipes complete all as specified and as directed.

M & L for steel tubes medium grade galvanised including all fittings and fixed complete to walls, floors and ceiling 15mm bore all as specified and directed by Engr-in-Charge.

M & L for steel tubes medium grade galvanised including all fittings and fixed complete to walls, floors and ceiling 20mm bore all as specified and directed by Engr-in-Charge.

S & F Bib tap, cast copper alloy , fancy type, chromium plated with wall flange screwed down, screwed for iron pipe, 15 mm bore, complete all as specified and as directed.

S & F PVC connection suitable for 15 mm pipe with PTMT nuts and washers on both ends of length 450 mm long, complete all as specified and as directed.

S & F sink made up of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and waste coupling , inlcuding bedding in cement mortar to dwarf wall or providing cantilever brackets, PVC waste pipe and connecting union to pipe overall size (495mm x 420mm) and bowl size (410mm x 330mm x 160mm), complete all as specified and as directed.

S & F Vitreous china squatting pan, water closet, orissa pattern of size 580 x 440 mm white, with integral foot rests and PVC (SWR) "S" trap (excluding flushing cistern and flush pipe) including provn of lime concrete bedding and jointing to flush pipe , complete all as specified and as directed.

S & F 10 litres capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32 mm dia PVC flushing pipe and 15 mm dia 450 mm long PVC connection with PTMT nuts, waste coupling complete all as specified and as directed.

S & F Steel windows ( box type) (double leaf, gauge and glazed) with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with / without glazing bars dovetailed or welded, complete all as specified and as directed.

M & L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and as directed.

S & F 3 mm thick plain sheet glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane, complete all as specified and as directed.

S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and as directed.

M& L for preparation of new or previously untreated steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

M & L for Plain cement concrete, (1:3:6) (Nominal Mix) type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels or drains etc, complete all as specified and as directed.

M & L Extra labour for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, incl forms, moulds, mitred / stopped ends etc, complete, all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortor bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 300 x 200 x 7 mm thick as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry, pointed in white or coloured cement to match laid over and including 10 mm thick rendering / backing coat in CM (1:4) to receive tiles, complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 600 X 300 mm x 7-8 mm thick as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry, pointed in white or coloured cement to match laid over and including 10 mm thick rendering / backing coat in CM (1:4) to receive tiles, complete all as specified and as directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile n.exc 0.11 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) all as specified and directed.

Preparation of old treated ceiling surfaces and applying two coats of white wash complete all as specified and as directed.

M & L preparation of old treated wall surfaces and applying two coats of white wash complete all as specified and as directed.

Taking down cement plaster, any description, on brick or stone walls, etc. including raking out joints hacking for key, scrubbing down with water etc., and removing unserviceable debris off the premises complete all as specified and directed.

M & L for rendering 5 mm thick on fair faces of concrete surfaces as in facia or ceiling in CM (1:3) finished even and smooth without using extra cement, complete all as specified and directed.

M & L for preparation of newly plastered or unplastered surfaces of ceiling or facia and applying two coats of white wash, complete all as specified and directed.

M & L for rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement,complete all as specified and as directed.

M & L for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed.

M & L for heavy duty (industrial) coloured tile of size 600 x 600mm,dark shade, stonex finish 16 mm thick (square/rectangular) polished in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM (1:6) complete all as specified and directed.

M & L for Non-skid ceramic coloured tiles of size 7 to 8 mm thick, area of each tile exc 0.18 Sqm but n.exc 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed 15 mm thick in CM (1:6) complete all as specified and as directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion washable over a coat of primer on walls complete all as specified and as directed.

M & L for precast cement concrete block masonry with solid blocks, made out of PCC 1:3:6 type C-1 (using 20mm graded stone aggregates), exceeding 10 cm in width and setting in CM (1:6), complete all as specified and as directed.

M & L for rendering 15mm thick in CM (1:4) on fair faces of brick/ stone or concrete surface finished even & smooth without using extra cement complete all as specified and as directed.

M & L for complete removal of existing treatment from external walls and applying two coats of weather coating external emulsion (APEX) over a coat of external primer complete all as specified and as directed.

M & L for preparation of old painted surfaces of wood and wood based materials of any description not other wise described over 10 Cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L for preparation of old painted surfaces of steel of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

S & F second class hard wood, plain, framed, panalled door shutters (any number of panels) 35 mm thick, with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face venneers; all as specified in cl No 8.24 (a) of SSR Part-I supplied and fitted to chowkats all as specified and as directed.

Cutting out concrete blocks, slabs, brick work or stone masonry (in alternate course) forming toothing for and bonding new work in mortar in to old work ,including new material entering old wall except block or slabs set in CM (1:6) complete all as specified and as directed.

S & F 30mm thick second class HW glazed and skeleton ,shutters, open rebated and prepared to received glass, gauge etc (with sash bar) edges of framing plain, chamnered or rounded and mitred, beads for securing glass etc., the size of member of shutter as specified in SSR Pt-I clause 8.24 (b) window & ventilators shutters and fitted to chowkat etc.,complete all as specified and as directed.

S & F second class hard wood plain solid ,straight chowkhats and frames wrought,framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints etc complete all as specified and as directed.

S & F MS Butt hinges medium weight cold rolled & fixed 100 mm long complete all as specified and as directed.

S & F MS Butt hinges medium weight cold rolled & fixed 75 mm long complete all as specified and as directed.

S & F aluminium handles, cast type, anodised of size 100 mm long, complete all as specified and as directed.

S & F aluminium, anodised, barrel tower bolts of extruded section, 100 mm long complete all as specified and as directed.

S & F for mild steel work for bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and as directed.

S & F 15 mm bore CP Angular stop cock with wall flange complete all as specified and as directed.

S & F 75 mm bore UPVC (SWR) pipes, Type 'B' single socketed , in any length, laid in trenches or in floors complete all as specified and as directed.

M & L for CI manhole cover (ISI marked) medium duty of size 600 x 600 mm including angle frame etc complete with fittings like handles, hinges etc., conforming to IS complete all as specified and as directed.

S & F for Steel rolling shutters 1.25mm thick of laths , without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated push pull or manual type complete all as specified and as directed.

Dismantling posts or struts ( wood /RCC/ steel) of any section embedded in concrete including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Dismantling fencing wire mesh of any type complete all as specified and as directed.

Excavation in post holes or similar holes each n.exc 0.5 Cum and getting out in hard /dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm thick, watering , well ramming and removing surplus soil to a distance n.exc 50m and making good surface all as specified and as directed.

M & L for providing plain cement concrete (1:4:8) type D-2, (using 40mm graded stone aggregate) as in foundation, filling and mass concrete all as specified and as directed.

S & F mild steel works in Joist, channel, angle or tee sections, posts, rafters, purlins, trusses, connecting plates, etc., fixed independently conforming to Fe-410-W(Gde E-250) quality 'A' complete all as specified and as directed.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long and n exc 10cm long, dia of neck 5 to 10mm all as specified and directed by Engr-in-Charge.

Supply only chain link MS galvanised fencing 50 x 50mm mesh and 2.50 to 2.90 mm dia wire / 100 x 100 mm mesh and 4mm dia wire all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standard rails, straining bolts etc including provision of binding wire all as specified and as directed.

S & F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed wire with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, securing or tying at crossings with and provn of galvanised mild steel wire, staples or steel pins etc., complete all as specified and as directed. Note : Each line wire shall be measured separately.

Dismantling wrought iron or mild steel work of any description not otherwise provided for incl doors, gates etc complete all as specified and as directed.

S & F for MS round bar 10 mm dia fixed independently including hooking ends for chain link fencing conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

S & F for Flat iron fillets (for securing wire mesh etc) including all necessary drilling , bolting or rivetting etc., and similar works conforming to Fe 290 Gde E 165 complete all as specified and as directed.

M & L for Reinforced cement concrete (Nominal Mix) (1:1 1/2:3) , type A-1 (using 20 mm graded stone aggregate) as in foundation, footing, plinth beam etc all as specified and as directed.

M & L for Reinforced cement concrete (Nominal Mix) (1:1 1/2:3) , type A-1 (using 20 mm graded stone aggregate) as in columns, pillar, posts and struts complete all as specified and as directed.

M & L for mild steel TMT bar 10 mm dia and over cut to length, bend to shape required including cranking, bending, hooking ends and binding with mild steel wire not less than 0.90 mm dia complete all as specified and directed.

All as per Item No 97 above but 6 mm to 8mm dia and upto 10 mm dia as in stirrups, spaces etc., complete all as specified and as directed.

M & L for use and waste of timber as in formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for fair finished surfaces of concrete flat all as specified and directed.

M & L for use and waste of timber as in formwork to sides of pillars, columns to rough finished surfaces of concrete ,square,rectangular or polygonal complete all as specified and as directed.

M & L for framed work as in doors or gates of angle iron or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering ,running rails and guides ) and hanging also fastening and fixing conforming to Fe 410 W Quality Gde E 250 quality A all as specified and as directed.

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in hard/ dense soil complete all as specified and as directed.

M & L for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) 100 mm thick as in sub base of floor complete all as specified and as directed.

M & L for cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) 40mm thick in flooring / sub base, finished fair and even complete all as specified and as directed.

M & L for machine pressed coloured pre-cast inter locking rubber moulded paver block any shape and size conforming to IS-15658-2006 of 80mm thick M-40 grade laid over and including 40 mm thick (Average) sand cushion complete all as specified and as directed.

M & L for providing cement concrete (1:2:4) type B-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete, walls or retaining walls, any thickness, size or shape including pilasters, buttresses, columns, pillars, boundary pillars and posts (including caps and bases) including necessary formwork all as specified and as directed.

S & F stainless steel tube 304 grade, any dia as in pole, stud, members etc including necessary plates, bolts and welding work required for errecting complete all as specified and as directed.

S & F 1.27mm thick stainless steel sheeting as in roof covering of the traffic controlling post fixed with screws/welding and bent to a curve (of any radius) complete all as specified and as directed.

M & L for 16-18 mm thick granite (of any type) slab machine cut, in flooring /skirting/dado etc set and jointed with grey with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, rounding edges as required, laid over and including 15mm thick screed bed in CM (1 :4) complete all as specified and as directed.

M & L for provn of stand type convex mirror on polycarbonate sheet of dia. 1000mm external diameter with 75mm dia MS pipe 1.80m height with 1.2 m above ground level as in stand and necessary clamps, bolts and nuts complete and fixed in ground with PCC bed block of size 450 x 450 x 450mm including cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggrigate) all as specified and directed by Engr-in-Charge. Make: Dark eye or equivalent makes.

S & F MS Angle iron 65 x 65 x 6mm conforming to Fe-500-O or Fe-550-O as in fencing post, including drilling holes notching for wire etc cutting and twisting necessary drilling, bolting and reveting or welding and similar works complete all as specified and as directed.

E/M PORTION Taking down old, unserviceable aluminium/copper point wiring (light, fan, socket or power) complete, including fixtures & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc., complete all as specified and directed by Engr-in-Charge. Note:- Cost of making good the disturbed surfaces is deemed to be included in the unit quoted rate.

Disconnecting /dismantling of old existing unserviceable DB's any way 240/415 Volts alongwith their /unserviceable burnt MCB's all as specified and as directed.

M & L for concealed point wiring with two single core 1.5 sqmm PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with multi stranded copper conductor drawn through and including non-metallic PVC rigid conduit (medium grade) with all fittings and accessories, ISI marked including provision of 1.5 Sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLS, ISI marked as earth continuity conductor (green in colour) and including cutting chases for conduits & making good to walls, floors etc. complete all as specified & as directed for the following:- (a) One light/fan/call bell point controlled by one switch. Make of Cable: Havells/ Finolex/ Polycab/ KEI. Note: (i) Modular boxes and cover plates shall be measured and paid separately. (ii) Cutting chases and making good the disturbed surfaces is deemed to be included in the unit quoted rates.

(b) One 5 Amps 5 Pin socket outlet on independent board complete all as specified and as directed.

(c) One 5 Amps 5 Pin socket outlet on the same board with other switches complete all as specified and as directed.

M & L for concealed point wiring with two single core 2.5 sqmm PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked, with multi stranded copper conductor drawn through and including non-metallic PVC rigid conduit (medium grade) with all fittings and accessories, ISI marked including provision of 2.5 sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLS, ISI marked as earth continuity conductor (green in colour) for housing 15/16 Amps switch-socket outlets etc., on independent board complete all as specified and as directed. Make of Cable: Havells/ Finolex/ Polycab/ KEI. Note: (i) Cutting chases and making good the disturbed surfaces is deemed to be included in the unit quoted rates. (ii.) Modular boxes and cover plates shall be measured and paid separately.

S & F Modular type socket out let 2 in 1, 6/16 Amps, 2 module, with ISI marked all as specified and as directed. Make : Verona of Crabtree, Cat No: ACVKCWW163 or techno-commercially equivalent in Legrand/C&S.

S & F Modular type switch single pole ,16 Amps one way, 1 module, ISI marked all as specified and as directed. Make : Verona of Crabtree, Cat No: ACVSXXW161 or techno-commercially equivalent in Legrand/C&S.

S & F Modular type switch single pole, 6 Amps one way, 1 module, ISI marked complete all as specified and as directed. Make : Verona of Crabtree, Cat No: ACVSXXW061 or techno-commercially equivalent in Legrand /C&S.

S & F Modular type socket out let 6 Amps 2/3 pin combined, 2 module, ISI marked complete all as specified and directed. Make : Verona of Crabtree, Cat No: ACVKSWW065 or techno-commercially equivalent in Legrand /C&S.

S & F modular metal flush box concealed on walls suitable for fixing switches/sockets of following modules all as directed. (a) 1/2 Module Note for Item Nos 122 to 122.30: The make of modular metal flush boxes should be same as that of switches/ sockets.

(b) 3 Module

(c) 4 Module

(d) 6 Module

S & F modular cover plate suitable for fixing switches/sockets of following modules all as directed. (a) 1/2 Module Note for Item Nos 123 to 123.30: The make of modular cover plates should be same as that of switches/ sockets.

(b) 3 Module

(c) 4 Module

(d) 6 Module

S & F ceiling rose, PVC /polycarbonate, isolated body, three terminals and 240 Volts, ISI marked complete all as specified & as directed. Make: Havells/CG/Anchor

S & F LED lighting fixture 240 Volts , 20 watts , CT 5700 K, CRI ≥ 80 , Luminous Efficacy ≥ 100 lm/ W, IP 20, IK 03, Class II, with extruded aluminium heat sink, milky white polycarbonate diffuser, wall or surface mounted 4ft LED batten with electronic driver, with all accessories internally prewired and including connecting up with twin/three core twisted flexible copper conductor cable of suitable size in and including flexible hose complete all as specified and directed by the Engr-in-charge. Make : Havells, Cat No : ENDURALINEARNEO BS20WLED865SPCWH or techno-commercially equivalent of Luker /Philips.

S & F LED lighting fixture 240 Volts,10 watts , CT 5700 K, CRI ≥ 80, Luminous Efficacy ≥ 100 lm/ W, IP 20, IK 03, Class II, with extruded aluminium heat sink, milky white polycarbonate diffuser, wall or surface mounted 2ft LED batten with electronic driver, with all accessories internally prewired and including connecting up with twin/three core twisted flexible copper conductor cable of suitable size in and including flexible hose complete all as specified and directed. Make : Havells, Cat No: ENDURALINEARNEO BS10WLED865SPCWH or techno-commercially equivalent of Luker/Philips.

S & F Exhaust fan 230 Volts, 35 watts, 50 Hz, single phase, 250mm sweep, air delivery 860 m³/h, rated speed 1200 RPM, noise level less than 44 dB, PVC body with their all accessories, fixed properly on window/ stone wall surfaces of thickness not exceeding 50 cm including making proper sized exhaust hole of 250 mm dia, louver shutter suitable for the same exhaust fan and which shall easily be operated with exhaust air pressure, connecting up from ceiling rose with twin/three core twisted flexible copper conductor cable of suitable size in and including flexible hose and any disturbed surfaces of wall shall be made good by cement work/plastering and matching by existing colour white/colour wash including removing of old exhaust fan and connecting/testing complete all as specified and as directed. Make: Havells, Code:Venti Air-DX White or techno-commercially equivalent in Almonard/ Usha. Note: Old unserviceable Exhaust fan shall be handed over to MES Store for keeping in safe custody.

S & F Sheet metal enclosure for 8 way DBs double door type, 240 volts, IP 43, IK 09, rated bus bars, earth bar, neutral links complete including blanking plates as required & fixed flush to wall/other surface including necessary connection all as specified and as directed. Make: Havells, Cat No: DHDNSHODDW08 or techno-commercially equivalent in ABB/ Legrand.

S & F Miniature Circuit Breakers, single pole, C-Series 240 Volts of capacity (6-32 Amps) as ordered breaking capacity of 10 KA, ISI marked all as specified and as directed. Make : Havells, Cat No:DHMGCSPF006-032 or techno-commercially equivalent in L&T/ Legrand.

S & F Miniature Circuit Breakers, SP& N, C-Series 240 Volts of capacity (6-32 Amps) as ordered breaking capacity of10 KA, ISI marked all as specified and as directed. Make : Havells, Cat No :DHMGCSNF006-032 or techno-commercially equivalent in L&T/ Legrand.

S & F Exhaust fan AC single phase 240 Volts, 145 watts, 450 mm sweep, air delivery 3700 m³/h, rated speed 1400 RPM, noise level less than 60 dB, metallic body with their all accessories, fixed properly on window / stone wall surfaces of thickness not exceeding 50 cm including making proper sized exhaust hole, connecting up from ceiling rose with twin / three core twisted flexible copper conductor cable of suitable size in and including flexible hose and any disturbed surfaces of wall shall be made good by cement work/plastering and matching by existing colour white/colour wash including removing of old exhaust fan and connecting/testing complete all as specified and as directed. Make: Havells ,Code: Turbo Force SP or techno-commercially equivalent in Almonard/ Usha. Note: Old unserviceable Exhaust fan shall be handed over to MES Store for keeping in safe custody.

S & F LED Gate light fitting 25 Watts, Ingress protection not less than IP 65, impact resistance not less than IK 07, CCT 5700K, CRI ≥ 70, Inbuilt SPD ≥ 4kV, symmetrical light distribution, isolated electronic LED driver with fixing accessories all internally prewired and including connecting up with twin /three core flexible copper conductor cable of suitable size including taking down the unserviceable fitting complete all as specified and directed by Engr-in-Charge. Make : Havells, Cat No: CORALPT25WLED757 PSYMTOPC or techno-commerciall equivalent of Philips/Luker

S & F loop in- loop out fuse junction box (CPRI type tested) of internal dimension 140 (H) x140 (W) x 95(D) mm, made of FRP sheet with weather proof canopy and locking screw fitted with and including 50 Amps rated 4 way connectors for 3 phase and neutral incoming/ outgoing, mounted in the box, fixing on steel tubular /rail poles /wall including necessary aluminium clamps, suitable glands, lugs and GI nut and bolts including taking down old unserviceable junction box complete all as specified and as directed. Make : Sintex, Cat No: GSJB-1414 or techno-commercial equivalent in Hensel.

Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings / equipment's etc., under ground cable, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade of cross sectional area, 2 Core 10 Sqmm complete all as specified and as directed. Make: Havells/Finolex/Polycab/KEI.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5m depth for erecting of poles, laying of cables and getting out in hard /dense soil complete all as specified and as directed.

Returning, filling in, including spreading levelling, watering and well ramming in layers n.exc 25 cm depth with excavated earth complete all as specified and as directed.

Removing excavated material (soil) to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5m above the starting point all as specified and as directed.

Supply and laying sub class 'B' bricks of size 230 x 115 x 75 mm laid across the cable for cable protection, above sand cushion complete all as specified and directed.

Supply, spreading and compacting of M Sand in trenches for cable cushion on both top and bottom of cable, including ramming all as specified and as directed. Note: Punned thickness only shall be measured.

S & F LED building security light fittings of 25 W , CT 5700 K , IP 66 protection, IK 07 protection, luminous efficacy ≥100 lumen/W, Power factor ≥ .90, SMD LED package, powered by built-in electronic driver with lower THD, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection & other safety tests as per IS 15885 including bracket made out of 40 mm dia light grade GI pipe of suitable length duly fixed with MS clamps nut, bolts etc., and connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size in and including flexible hose pipe complete all as specified and as directed. Make: Havells, Cat No: ENDURAPEARLSL25 WLED757SASYTOPC or techno-commercially equivalent in Philips/Luker.

M & L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron including PCC earth pit & cover with suitable handle, including necessary excavation and earth work in any type of soil, 20 mm dia medium grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15 mm bore medium grade galvanized steel tubing for drawing earth lead GI wire protection & common salt, charcoal in alternate layers etc. complete all as shown in Electric Plate No 3 of SSR Part 1 and testing on completion complete all as specified and as directed. Note: On testing after completion, if the desired earth resistance is not found according to the relevent Indian standards it is to be redone to the entire satisfaction of Engr-in- Charge at no extra cost to the Dept.

Taking down old sub-main wiring including fixtures & fittings etc., and removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc., complete all as specified and as directed.

M & L for surface point wiring with 1.5 Sq mm, FRLS PVC insulated, single core, copper conductor cable, 1100 Volts grade, multi stranded in and including PVC capping casing medium grade for one light /exhaust fan /call bell point controlled by one switch with and including continuous 1.5 Sqmm FRLS PVC insulated single core copper conductor cable for earth continuity conductor green in colour connected to common earth and earth dolly, in and including PVC / polycarbonate rectangular block / boxes of suitable size & thickness with suitable PVC/ polycarbonate cover for mounting switches, sockets etc., complete all as specified and directed for the following : (a) One Light /fan/call bell point controlled by one switch 5/6 Amps. Make : Havells/Finolex/Polycab/KEI. Note :- (i) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth.

(b) One switch socket out let point 5/6 Amps on independent board complete all as specified and as directed.

(c) One switch socket out let point 5/6 Amps on the same board with other switches complete all as specified and as directed.

M & L for surface point wiring with two single core 2.5 Sqmm FRLS PVC insulated, single core, copper conductor cable, 1100 volts grade, ISI marked with multi stranded in and including PVC capping casing medium grade in wall for 15/16 Amps switch-socket outlets etc., on independent board complete and including continuous 2.5 Sqmm FRLS PVC insulated single core copper conductor connected to common earth dolly, in and including PVC/polycarbonate rectangular block /boxes of suitable size & thickness with suitable PVC /polycarbonate cover for mounting switches, sockets etc., complete all as specified and directed. Make : Havells/Finolex/ Polycab/ KEI. Note :- (i) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth.

M & L for surface sub-main wiring alongwith earth wire of size (2 x 2.5) Sq.mm + (1 x 2.5) Sq.mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC capping casing (medium grade) with all fittings and accessories ISI marked complete all as specified & as directed. Make : Havells/Finolex/KEI/Polycab. Note : (i)Two runs of PVC wire, one run of earth wire & one run of PVC capping casing (medium grade) shall be measured as one length.

S & F switch socket combination, 5 in 1, 5/6 pin, 15 Amp flush type, 240 volts, ISI marked complete all as specified and as directed. Make: Havells/Anchor/C&S/Legrand.

S & F switch piano, flush button, single pole, one way, 5/6 Amp, 240 volts, ISI marked complete all as specified and as directed. Make: Havells/Anchor/C&S/Legrand.

S & F switch socket outlet 5 Pin, 5/6 Amp flush type, 240 volts, ISI marked complete all as specified and as directed. Make: Havells/Anchor/C&S/Legrand.

S & F socket out let 5 Amps, 240 volts, ISI marked complete all as specified and as directed. Make: Havells/Anchor/C&S/Legrand.

S & F bell push, flush type, 5/6 Amps complete all as specified and as directed. Make: Havells/Anchor/C&S/Legrand.

S & F Call bell, AC, Ding Dong type 230 volts complete all as specified and as directed. Make : Anchor, Cat No : 8272 or equivalent in Legrand/C&S/Havells.

S & F energy efficient and environmental friendly, ultra slim elegance LED lighting fixture with extruded aluminium heat sink, 20 Watts, 4ft and connecting up with & including twin/three core twisted flexible copper Conductor cable of suitable size in & including flexible hose pipe from ceiling rose to fitting complete all as specified and directed. Make : Havells, Cat No : LUMILINEPLUSBS 20WLED865SPCSS or techno-commercial equivalent of Luker/Philips.

S & F Compact & sturdy LED decorative fixture 10 Watts with extruded heat sink, multi purpose lighting in replacement of 2ft FTL fittings and connecting up with & including twin/three core twisted flexible copper Conductor cable of suitable size in & including flexible hose pipe from ceiling rose to fitting complete all as specified and directed. Make : Havells, Cat No: LUMILINEPLUSBS 10WLED865SPCSS or techno-commercial equivalent of Luker/Philips.

S & F decorative wall mounting fixture with opal PC diffuser suitable for lamps with B22 base with and including 10W LED lamp and all accessories internally prewired and including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size in flexible conduit all as specified and as directed. Make: Beetle of Havells, Cat No: LHDL07150099 or techno-commercial equivalent of Philips/Luker. Make for lamp :Havells, Cat No : LHLDERHEMD8X010 (for lamps) or techno-commercial equivalent of Philips/Luker. Note: The cost of making good and matching to the existing surface is deemed to be included in the unit quoted rates.

S & F energy saving new generation 10 Watts LED, bulk head luminaire with opal diffuser with and including lamp LED 6000K complete all as specified and as directed. Make: Havells, Cat No: RUGBYNEONFT 10WLED860SSYMTOPC or techno-commercial equivalent of Philips/Luker.

S & F Sheet metal enclosure for 6 way DBs double door type 240 Volts, 200 Amps rated bus-bar IP-43, IK-09 with metal door, including necessary connection all as specified and as directed. Make: Havells,Cat No :DHDNSHODDW06 or equivalent in L&T/ Legrand.

S & F in replacement PVC insulated flexible multicore round copper conductor cable of size 2 core 10 Sqmm including necessary end connector including taking down unserviceable cable complete all as specified and as directed. Make :Havells, Cat No: WHMFDSKB2010 or equivalent of Finolex/KEI/Polycab.

GMS Builders

SREERAM