Construction of 450 seated Auditorium SIRD and PR Campus, Bhubaneswar.

CIVIL WORK Earthwork in excavation in all types of soil (Hard soi,ordinary soil,stony earth) for site leveling, foundation, pits, trenches and other civil works upto and including 1.5metre depth and stacking the soil upto a lead of 100 metre and including dewatering, removing slush, shoring and strutting (as required), complete as per specification and as directed by the Engineer-In-Charge.

Ground Floor

Compound wall

Entrance Gate with Security Shed

Paver road

Drainwall

Filling at all depth with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 15cm in depth: consolidating each deposited layer by ramming and watering complete (lead upto 100m) as directed by the Engineer-In-charge.

Ground Floor

Compound wall

Entrance Gate with Security Shed

Drainwall

Supplying and filling in foundation and plinth with good quality river sand including watering, ramming with cost, conveyances, royalties of all materials and cost of all labour with T&P required for the work etc. complete as per specification & direction of Engineer-in-charge

Ground Floor

Compound wall

Entrance Gate with Security Shed

Drainwall

Providing & applying of pre constructional anti-termite treatment by drilling 12mm dia holes at distance of 30cm @ junction of wall & floor about 300mm apart deep enough to reach the soil below & chemical emulsion (IMIDACHLOPRIED 30.5SC mixed with 47.5ltr water) pumped these holes to soak the soil @ 1 ltr solution of each hole as per manufactures specification & the holes should be pluged the filling materials including cost of all materials, labour,conveyance, T&P , all taxes and hire charges of machinaries as per direction of Engineer-in-charge.

Ground Floor

Cement concrete of proportion (1:3:6) in foundation and floors using 4cm size clean hard black crusher broken granite stone metal of approved quality and from approved quarry including hoisting, lowering and laying concrete in layers not exceeding 15 cm. (6") thick to the required level ramming, watering, curing etc. complete including cost, conveyance, royalties of all materials with all labour and T&P required for the work etc. complete in all respect and as per the direction of the Engineer-in-charge.

Ground Floor

Compound wall

Entrance Gate with Security Shed

Drainwall

Fly Ash brick masonry in cement mortar (1:6) in foundation & plinth using Fly Ash bricks of 25 x 12 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including cost, conveyance, royalties of all materials with all labour,labour cess and T & P required for the work complete in all respect as per direction of Engineer-in-Charge.

Ground Floor

Entrance Gate with Security Shed

Fly Ash brick masonry in cement mortar (1:6) in super structure using Fly Ash bricks of 25 x 12 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including cost, conveyance, royalties of all materials with all labour,labour cess and T & P required for the work complete in all respect as per direction of Engineer-in-Charge.

Ground Floor

First Floor

Terrace Floor

Compound wall

Entrance Gate with Security Shed

Fly Ash brick masonry in cement mortar (1:4) in super structure using Fly Ash bricks of 25 x 12 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including cost, conveyance, royalties of all materials with all labour,labour cess and T & P required for the work complete in all respect as per direction of Engineer-in-Charge.

Ground Floor

First Floor

Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position.

FOUNDATION

Ground Floor

Compound wall

Entrance Gate with Security Shed

Pedestal

COLUMN

Ground Floor

First Floor

Terrace Floor

Compound wall

Entrance Gate with Security Shed

PLINTH BEAM

Ground Floor

Compound wall

Entrance Gate with Security Shed

LINTEL & SILL

Ground Floor

First Floor

Terrace Floor

ROOF BEAM

Ground Floor

First Floor

Terrace Floor

Compound wall

Entrance Gate with Security Shed

ROOF SLAB

Ground Floor

First Floor

Terrace Floor

Compound wall

Entrance Gate with Security Shed

CHAJJA

Ground Floor

First Floor

Terrace Floor

STAIRCASE

Ground Floor (Staircase, Auditorium, Gallery)

First Floor

RETAINING WALL

DRAIN

Drain base

Drain wall

Drain slab

Supplying Cutting, straightening coiled or bent up M.S. Rod or tor steel of primary steel producers such as SAIL / Tiscon / RINL / JINDAL STEEL / SHYAM STEEL (grade Fe-500D) etc. including bending, binding, welding, wastage & over lapping and jointing if necessary and tying the grills and placing in position as required for R.C.C. Work and for providing fan hooks as required, hoisting, lowering, laying including cost, conveyances of M.S. Rod or tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all floors with labour cess etc. (payment will be made on standard weight of B.I.S. for M.S. Rods or tor steel only) etc. complete as per specification & direction of Engineer-in-charge.

Ground Floor

First Floor

Terrace Floor

Compound wall

Entrance Gate with Security Shed

Drain

Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge. (Outer side)

Ground Floor

First Floor

Terrace Floor

Compound wall

Entrance Gate with Security Shed

Drain

Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge. (In side)

Ground Floor

First Floor

Providing 16 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge.

Ground Floor

First Floor

Terrace Floor

Entrance Gate with Security Shed

Providing 6 mm thick cement plaster with cement mortar of mix (1:4) with screened and washed sharp sand for mortar and finished smooth to R.C.C. work after closed deep chipping & slurry treatment including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge.

Ground Floor

First Floor

Terrace Floor

Entrance Gate with Security Shed

Fixing granite tiles of approved dimension area above 0.4 sqm (20mm thick) in floor, treads of steps and landing on 20mm thick bed of cement mortar (1:4) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing etc. complete with cost, conveyance, royalties of all materials complete in all respects as per direction of Engineer-in-Charge.

Ground Floor (Staircase,Lift & Ramp)

First Floor (Staircase & Lift)

Entrance Gate with Security Shed

Supplying, fitting and fixing vitrified tiles of premium grade having thickness 8mm to 10mm confirming to IS 13756 of size 600mm x 600mm Plain (Ivory) of approved make (JOHNSON / SOMANY/ KAJARIA/ RAK) in floors on 20mm thick bed of C.M. (1:4)(1cement:4course sand) and filling the joint with white cement mixed with pigment to match the shades of the tileincluding cost of all materials, labour, labour cess, T&P etc. required for the work complete in all respect as directed by the Engineer in charge.

Ground Floor

First Floor

Entrance Gate with Security Shed

Providing, fitting, fixing vitrified tiles of premium grade having thickness 8mm to 10mm confirming to IS 13756 of size 600mm x 600mm Plain (Ivory) of approved make (JOHNSON / SOMANY/ KAJARIA/ RAK) as directed by Engineer-in-charge in dados skirting and risers of steps on 12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing etc. complete with cost, conveyance, royalties of all materials all labour,labour cess complete in all respects as directed by the Engineer in charge.

Ground Floor

First Floor

Entrance Gate with Security Shed

Fixing of Kota tiles of minium thickness 16mm thick of premium grade of size above 0.10 Sqm. in floors over 20mm thick bed of cement mortar 1:4 (1cement:4course sand)and filling the joint with white cement mixed with pigments to match the shade of the tiles, including rubbing & polishing etc. complete including cost, conveyance, royalties of all materials, labour,labour cess with T&P complete in all respects as per direction of Engineer-in-Charge.

Ground Floor

First Floor

Supplying, fitting and fixing vetrified Industrial tiles in floors of premium grade having thickness 8mm to 10mm of size 300mm x 300mm confirming to IS 4457 with colour / printed series of approved make (JOHNSON /RAK / SOMANY/ KAJARIA or equivalent ) on 20mm thick bed of C.M. (1:4) including cost of all materials, labour, T&P etc. required for the work in all respect as directed by the Engineer in charge.

Ground Floor

Providing and fixing ISI marked 35 mm thick flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak three ply veneering with vertical grains or cross bands and face veneers on both faces of shutters of approved design including cost of all door fittings and fixtures etc. complete as directed by the Engineer in charge.

Ground Floor

First Floor

Entrance Gate with Security Shed

Supplying , fitting and fixing of openable UPVC doors with door frame of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures as directed by the Engineer in charge. (Make-FENESTA/ Koemmerling/ Saint Gobain/ Prominance)

Glaze Fire Door :- Providing and fixing of glazed fire door for 120 mins fire rating. Glazed door shall be tested as per IS/ISO 834-1,IS/ISO 3009-1, IS16947 for 120 mins fire rating.Door frames and partitions shall be single rebate frame profile of size 125 x 60mm made out of 1.60mm GI (120GSM).Door leaf shall be fully glazed with minimum 60 x 120mm profile step box section for taking glass elements. Door leaf shall be manufactured from 1.2mm GI (120GSM). Doors shall be 60mm thick and the internal construction of the door should be rigid reinforcement pads for stability of profile.For doors and partitions,beeding shall be minimum 1.2 mm GI with 25mm height, with screws 6 x 19mm.The infill material shall be resin bonded honycomb for rigidity.The glass shall be, ultra clear fire rated glass E120 minimum 8mm thick, for (E) 120 minutes integrity with light transmission of minimum 92% as per EN1363 and EN1364. Glass shall have a impact resistance of 1B1 as per EN 12600,Glazing kit to be provided along with steel beeding and ceramic tape.

Doorset shall include following hardware and accessories as a complete assembly.SS ball bearing hinges of SS-304 grade of size 100x75x3mm,Fire rated mortise dead lock, 55mm BS, 20mm sq. forend, including escutheion, with both side key cylinder, 1pairs Pull handle D type,22dia,CTC 300mm, back to back, with spindle, SS 304, SSS finish.Door closer with spring size of EN 2-4,as per EN1154 and CE marked.Doorset finished in desired colour of powder coating not less than 50microns including suitable anchors all inclusive for fixing of doorset.Rate shall include supply and installation of frame,shutter as a complete assembly including all hardware,& glass with tape.Manufacturer test certificates shall covers complete door set as a un-latched assembly with a valid test certificate not exceeding 5 years from the date of issue of report. (Make: Saint gobain/ SHAKTI HARMN).

Ground Floor

First Floor

Providing and fixing of 12mm thick cleartoughened glass framelessdoor with dorma premium fittings ,dorma premium(9111198)unilite package bts 75,ul pt 10 with cover UL PT 20 with cover UL us 10 Luckwith cover and pt 24 dorma premium (9137121) h type handle 450mm ,12mm clear toughened glass with cutout and hole, including the cost of all materials, hardware fittings, cost of all labour, conveyance,loading,t&p, etc,completeas per the direction of engineer in charge.

Ground Floor

Supplying , fitting and fixing of two track UPVC sliding window of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures as per direction of Engineer-in-charge. (Make-FENESTA/ Koemmerling/ Saint Gobain/ Prominance)

Ground Floor

First Floor

Terrace Floor

Entrance Gate with Security Shed

Supplying and fixing of Double skin Wall panelling made of aluminium anodised section framing conforming to standard aluminium section as horizontal and vertical members with atleast 600mm c/c and fixing of 9mm thick BWR ply with 4mm thick veneer pasting finished with melamine polished on both the faces complete as per direction of Engineer-in-charge.

First Floor

Supplying, fitting & fixing in all floors of M.S. grills, grill gates, M.S. gates, garage door, collapsible gates with top and bottom rails, steel windows, critical frames for windows, stair case and parapet railing made out of M.S Square bar/ flat including stair case hand railing with 40mm. dia G.I.pipe etc. including painting two coats over a coat of redoxide primer as per approved drawing and design with cost of all materials & labour, labour cess, T&P, sundries etc. complete in all respect as per specification & direction of the Engineer-in-Charge.

Ground Floor

First Floor

Terrace Floor

Entrance Gate with Security Shed

First Floor (Catway)

Priming one coat with wall cement primer (water bound) to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess T&P etc. complete as per the direction of the Engineer-in-charge. (Internal Surface) (Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge).

Ground Floor

First Floor

Terrace Floor

Entrance Gate with Security Shed

Priming one coat with wall cement primer (water bound) to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess T&P etc. complete as per the direction of the Engineer-in-charge. (External Surface) (Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge).

Ground Floor

First Floor

Terrace Floor

Compound wall

Entrance Gate with Security Shed

Wall painting two coats with Antifungal weather coat paint (1st quality) exterior grade of approved make & approved shade over a coat of primer to make an even finished surface in all floors and heights with all scaffolding and staging charges including cost, conveyance, cost of all labours, T & P, sundries etc. as required for the work complete in all respect as per the direction of the Engineer-in-Charge. (Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge).

Ground Floor

First Floor

Terrace Floor

Compound wall

Entrance Gate with Security Shed

Finishing plastered surfaces of walls with cement based wall putty (Water based) of approved make (JK White/ Birla white or equivalent make duly approved by Engineer-in-Charge) and finishing the surface smooth and even by sand papering to receive painting in walls, at all heights with staging wherever necessary with cost, conveyance, cost of all labour,labourcess, all T&P etc. required for the work complete in all respect as per the direction of the Engineer-in-charge.

Ground Floor

First Floor

Terrace Floor

Painting two coats with plastic emulsion paint with a approved quality primer to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess, T&P etc. complete as per the direction of the Engineer-in-charge. (Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge).

Ground Floor

First Floor

Terrace Floor

Entrance Gate with Security Shed

Painting two coat with approved synthetic enamel paint to new iron work over a coat of Red oxide primer including cost, conveyances, royalties, taxes of all materials and cost of all labour with T&P required for the work etc. complete as per specification & direction of Engineer in charge. (Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge)

Ground Floor

First Floor

Terrace Floor

Entrance Gate with Security Shed

Expansion joint Treatment

Supplying and fixing of Elastomeric Membrane of 200mm x 2mm size for expansion joint sealing from approved manuefacturer, fixing with epoxy adhesive of approved quality complete as per specification & direction of Engineer in charge.

Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @ 0.90mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc with cost, conveyance, cost of all labour,labour cess, T&P etc. required for the work complete in all respect as per direction of the Engineer-in-charge. (Make-JINDAL )

Ground Floor

First Floor

Texture paint : Providing and painting with Asian make concrete Texture paint of on the plastered surface of outer wall including scaffolding complete as per approved specification and direction of the Engineer-in-charge with cost of all materials. labour, T&P and Hire and running charges of machineries etc. all complete as per direction of the Engineer-in-charge.

Ground Floor

First Floor

Supplying , fitting and fixing of grid mineral fibre ceiling board having size 600 mm x 600 mm x 16mm of approved design and quality complete with frame and all fitting and fixtures as per direction of the Engineer-in-charge.

Ground Floor

First Floor

Supplying and fixing of Wall panelling made of aluminium anodised section framing conforming to standard aluminium section as horizontal and vertical members with atleast 600mm c/c and fixing of 9mm thick BWR ply with 4mm thick veneer pasting finished with melamine polishing complete.

Ground Floor

First Floor

Providing and fixing of UV Protected Multicell Polycarbonate panels with aluminium /MS structure with necessary fitting and fixtures and fasteners etc as per the shop drawing provided by approved agency) conforming to the detail technical specifications as below and as per approved colour and directions of Engineer-In-Charge including the cost of cost of all labours, materials, conveyance, loading and unloading, sundries and T&P etc all complete as per direction of the Engineer -in-charge. (Make- Sabic /Ultralite/DPI Daylight/Equivalent)

Ground Floor

Metal Cladding Works - Interlocking System with Perforation. Supply and fixing of Zinc Titanium cladding System as per EN 988 standards made with 1 mm thickness Zinc Titanium Alloy comprising of the following layers: Top Layer: Zinc titanium alloy as per EN988 standard Custom panels wall cladding system of thickness 1 mm. Custom Panels shall be of 300mm width as per approved drawings X up to 2400 mm length with CNC circular perforation as per standard in zinc titanium custom finish. Screen Cladding Zinc panels are rainscreen system with available pan width of panels of custom size as per apprioved drawings & manufacturer recommendation .Panels are attached to supports/substrates using stainless screws located under edges of the panels. Panels to have PVDF post coating after perforation of panels as per approved RAL shade PVDF coating finish having two coats accumulating to MINIMUN 30 microns total coating thickness. Coating will include a primer coat followed by a topcoat containing the color. Coating will have 70% PVDF & 30% Acrylic resin percentage. Total dry film thickness will be ranging between 1.2 to 2.2 DFT. Zinc Manufacturer should have direct registered office in India for more than 5 years and should have supplied Zinc roofing or Cladding to Government Projects in India. The Installation agency for Installation of Zinc cladding system shall be approved by the Manufacturer and should have completed Zinc Titanium cladding works for Government Projects. Approved Makes : VMZINC, SILESIA, IEQSA

Ground Floor

Second Layer : 25 mm X 50 mm Aluminium Box section installed at a spacing of 600 mm centre to centre on the plastered wall with suitable brackets /fasnteres. Zinc Interlocking panels shall be fixed over the alumnium box section substructure using stainless screws

Supply & fixing of 0.7 mm flashing in the same finish as the façade finish for Fascia, Top, bottom ,corners,etc as required for site detailing Maximum Girth of flashing upto 250 mm

Supply and Fixing of 0.80 mm thick Galvanized Stiffeners maximum girth of 250 mm.

Supply, Fabrication & Erection of MS structure using MS plate of 150 x150x10mm as base plate by means of anchor fastener of M10x100mm to be fixed with wall/beam from which MS SHS 50x50x2.6mm to be used as vertical and horinzontal section fixed on connecting support to hold the aluminium sub structuer for facade installation

RECEPTION BACK DROP :-Providing and fixing of 75-150 thick parttition with vinyl sheet / corian / sand stone /19 MM TH Onyx as a backdrop for the Reception. The structure shall be made of 19 mm th bwp ply members 55mmx 40mm and then over it 6mm bwp ply shall be fixed and then the corian shall be fixed to the partitions. The joints shall be finished with silicon adhesive to match withe the shade of the corian. as per the detail design and specifications and inclusive of all cost of labour, materials, T&P etc complete as per the directions of the EIC/Architect.

Ground Floor

CONSOLE / display unit :- Providing, fitting and fixing the console /display unit made of 19mm bwp ply and finished with 1mm thick texture / suede laminate , 12 mm th glass shelf whwever necessary and the exposed edges& wooden surface are to be finished with wooden lipping and finshed with automative paints/polish with melamine finish as per approved design and specifications including cost of all materials, labour, hardware if any etc. complete as per the detail design & directions of the EIC.

Ground Floor

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete as per the directions of the EIC.

First Floor

Fitting & fixing of G.C.I sheet in roof including fixing of ridges wind ties etc. complete but excluding cost of fitting including drilling holes in wind ties.

First Floor

STORAGE BELOW PANTRY PLATFORM (MODULAR): - Base Cabinets & Wall Cabinets :-Carcase is made up of bwp (Boiling Water Resistant) Plywood with Mini fix systems. Both side Laminated with all around PVC Edge Banding. Carcase Specification Details: 1. Plywood Thickness - 18 mm after both side off-White lamination & all around PVC Edge Banding. 2. Base & Wall Cabinet Height - 700 mm. 3. Wall Cabinet Depth - 350 mm (Including Shutter) 4. Base Cabinet Depth - 580 mm (Including Shutter) 5. PVC (Polyvinyl Chloride) Front Edge Banding Thickness – (2 x 22 mm). 6. Frame Thickness- 18 mm after both side lamination & all around PVC Edge Banding. Shutters & Others Wood Works :- Shutter is made up of bwp (Boiling Water Resistant) Plywood with both side Lamination & all around PVC Edge Banding. Shelf & Base and Back Details: 1. Plywood Thickness -18 mm after both side lamination & all around PVC Edge Banding. 2. Laminate Thickness – 1 mm 3. PVC (Polyvinyl Chloride) Edge Banding Thickness – (2 x 22 mm)

Hardwares :-All Kitchen Hardwares & Fittings are from HAFLE (SS 304) or as per company standards specified. Accessories :- All Kitchen Hardwares & Fittings are from HAFLE (SS 304) or as per company standards specified.▪ PVC Cutlery Tray- 1 Pc ▪ 4" Plain Wire Basket- 1 Pc ▪ Cup & Saucer Basket- 1 Pc ▪ Thali Basket - 1 Pc ▪ 8" Plain Basket- 4 Pc, ▪ Waste Bin Holder- 1 Pc ▪ Fixed Detergent Rack- 1 Pc ▪ Magic Corner- 1 Pc(Dores) ▪ Bottle Pullout- 1 Pc ▪ Cylinder Trolley- 1 Pc as per the detail design and approved by the EIC.

First Floor

OVER HEAD STORAGE :- Providing and fixing of over head storage cabinet of depth 450 mm with out drawer with 19mm th bwp & 6 mm th bwp ply wood at the back side and finished with 1.0 mmth texture / suede laminates,8mm th glass in shutter and finished the teak wood lipping with mat finish enamel paint or polish with mellamine to match the laminate shade , internal surface finished with 0.8 mm th laminate as per the detail design and approved by the EIC. ( Basic cost oftexture laminate is Rs60.91/- sft )

First Floor

SNACKS BAR COUNTER :- Providing & supplying of snacks bar counter with provision of flap door WITH storage made out of 19 mm th bwp ply & finished with glass , ss pipe, 6 mm th sold surface / granite where ever necessary . & inner surface finished with 0.8 mm th laminate & beading to be finished with automative paint or mellamine polish including all types of material, labour , hardware etc. as per the detail design & specifications approved by EIC . ( Basic cost oftexture laminate is Rs 60.91/- sft )

First Floor

Providing and laying grading conc. 25 mm (avg. thickness) cement concrete of required slope of mix 1:2:2 (1cement:2sand:2 graded stone aggregate of 10 mm nominal size) mixed with approved water proof compound as per manufacturer's specification on top of slab including cement slurry, all complete, including the cost of water proofing admixture, which should be approved by the Engineer-In-Charge prior to material procurement by the contractor.

First Floor

Waterproofing Treatment :- Terrcae Roof Top Surface: Providing and installing two component acrylic modified cementitious waterproofing coating with masterseal 551/Equivalent over roof slab after carrying out pond test on roof slab filling all defects, saturating the surface mixing the products and then application in 2 mm thickness (1.8kg/sqm coverage rate for 1mm thickness ) in suitable layers complete in all respect, all materials, tools,plant & labour complete in all respect.

First Floor

Dismantling brick or stone masonry in lime or cement mortar under 3m height including stacking the useful materials for re-use and removing the debris with in 50m lead including cost of all labour with T&P etc. complete as per the specification and direction of the Engineer-in-charge.

Dismantling G.C.I. or A.C. sheet roofing after carefully removing the bolts and nuts including stacking of he materials for reuse and removing the debris within 50m lead including cost of all labour with T&P etc. complete as per the specification and direction of the Engineer-in-charge.

Dismantling and removing doors, windows and ventilators including removal of frame, hinges, fastening and stacking the same for reuse and removing the debris within 50m lead including cost of all labour with T&P etc. complete as per the specification and direction of the Engineer-in-charge.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, laying in uniform layers with paver in subbase/ base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per Clause 406 of MoSRT&H Specifications for Road & Bridge works (4th Revision)

Pathway

Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision)

Pathway

Supplying and fixing of 80mm thick cement concrete interlocking paver block of M-40 grade of approved make,design,colour and size made by block making machine with proper compaction laid in required pattern etc. complete in all respect confirming to IRCSP63:2018 (as per SoR 2022, page : 233)

Pathway

Supply of 50mm thick pre-painted standing seam insulated roof system with an insulation core auto adhesively bonded to the external and internal faces during manufacturing providing strength and rigidity to the panels, having a nominal 1016mm effective cover width with 50mm crest at seeming location suitable for roof slope up to 1:20.The external and internal facers of the panel shall be lightly profiled with 1.5mm high continuous ribs with fixed widths providing micro-rib (MR) finish. Panel external and internal both facers shall be manufactured from 0.50mm (TCT) thk pre-painted galvalume steel material respectively with minimum 300 MPa yield strength coated with hot dip metallic Aluminium /Zinc alloy coating, Galvalume AZ150 as 150 gms/sq.mt total on both sides of Aluminium (55%) & Zinc (43.50 %) & Silicon (1.50%), conforms to IS 15695 or ASTM792M or AS1397 with a paint finish as silicon modified polyester (SMP).The insulation core shall be CFC, HFC and HCFC free polyurethane (PUR) insulation. Supplier to provide panel calculations to verify panels will withstand the design operational loads for wall indicated without detrimental effects as per BS EN 14509-2013 specifications. When tested to ASTM C518 panel to provide thermal transmittance (U) value of 0.44 W/m2K. When tested to ASTM D1621 and ASTM D1623, panel to provide compressive strength of 110 kPa and tensile strength of 100 kPa respectively. Panels shall be engineered to provide weathertight performance by using appropriate flashings along with non-skinning butyl sealant wherever applicable. Product to be certified to IGBC Green Pro Eco Label or GRIHA certification to demonstrate the sustainability of the product.

Magnesia board False Ceiling :- Supply and Installation of false ceiling 10 mm thick Tufbloc magnesium oxide HDFR boards of size 1200 x 2400 mm having Density-1000 kg/mt cube, with STC- 34 – 50, weight - 8.5 kg /sq mt, Fire Class - 1&P & Thermal Heat Resistance - 0.11792 W/mK Climate ( degree Centigrade , RH - 50,95 , Green VoC , RC% - Low & 30 Water resistant with wet expansion less than -0.02% from ambient to saturation, Moisture Movement - 0.02% from Anutone / Win Win / Magnum are to be fixed with head screw is fixed by using concealed ceiling system. The concealed ceiling system shall include GI Wall channel(WC 25) having thickness 0.45 mm, length 3600 mm, unequal flanges of 15 & 20 mm and web of 22 mm should be fixed along the perimeter of the wall with nylon sleeves and suitable fasteners at every 300 mm center. Then suspend Main channels(MC 45) having thickness 0.9 mm, length 3600 mm, equal flanges of 15 mm and web 45mm from the soffit at every 1200 mm centers with Suspender angle(SA 25) having thickness 0.45 mm, unequal flanges of 25 & 10 mm. GI Cross channel(CC 25) having thickness 0.45 mm, length 3600 mm, knurled web 35mm, depth of 25 mm and equal flanges 9.5 mm is fastened to the Main channel in the direction perpendicular to the Main Channel at every 600mm center. Now the jointing & finishing of the same will be done by using jointing kit consist of powder mixed with water and apply the same with flat flap on the boards joints to finish the surface of the boards so as to look flush. Apply synthetic poly fiber PF 5 x 50 accoustic wool of 50 kg density to be kept on the top of the ceiling by laying on the framework. Test certificate of the use products shall be submitted after procurement of materials. The rate shall be exclusive of trap door which shall be paid for separately. including all cost of materials , labour, overheads T & P etc., complete. (App make :- ANUTONE / GYPROC / USGBORAL /EQUIVALENT)

Stage area False Ceiling :- WOODEN FALSE CEILING WITH LAMINATE :- Providing and fixing of wooden false ceilling with 19 mm bwp PLY frame work and then fixing 6 mm th bwp ply to it over which is finished with 1 mm th SUEDE/TEXTURE laminate & fixed by means of stainless steel sturds & polished with mellamine including all the cost of material & labour , t& p etc complete and as per the direction of EIC / ARCHITECT . (App make FOR PLY :- AUSTIN / GREEN PANEL / GREEN PLY ECOTEC / EQUIVALENT & FOR LAMINATE - GREEN LAM / MERINO / CENTURY / EQUIVALENT )

VENEER WOODEN RAFTER FALSE CEILING :- Providing and fixing of wooden rafter false ceilling of size 50 x125 made outof with 19 mm bwp PLY frame work and then fixing 6 mm th bwp ply to it over which is finished with 4 mm th VENEER & fixed by means of stainless steel sturds & polished with mellamine including all the cost of material & labour , t& p etc complete and as per the direction of EIC / ARCHITECT . ( Basic cost of VENEER - Rs 250/ sft ) (App make FOR PLY :- AUSTIN / GREEN PANEL / GREEN PLY ECOTEC / EQUIVALENT & FOR VENEER - GREEN LAM / GREEN PANEL / CENTURY / EQUIVALENT)

WOODEN FALSE CEILING WITH VENEER :- Providing and fixing of wooden false ceilling with 19 mm bwp PLY frame work and then fixing 6 mm th bwp ply to it over which is finished with 4 mm th VENEER & fixed by means of stainless steel sturds & polished with mellamine including all the cost of material & labour , t& p etc complete and as per the direction of EIC / ARCHITECT . ( Basic cost of VENEER - Rs 250/sft ) (App make FOR PLY :- AUSTIN / GREEN PANEL / GREEN PLY ECOTEC / EQUIVALENT & FOR VENEER - GREEN LAM / GREEN PANEL / CENTURY / MERINO / EQUIVALENT)

WOODEN PANELING WITH VENEER :- Providing and fixing wooden panelling of thickness 75 mm - 400 mm suitably fixed to the walls with 19 mm thick bwP ply , finished with 4 mm thick VENEER complete with necessary Hardwood, skirting , mouldings & teak wood beading on the edge etc. as per the detail design including the cost of all materials, labour, overheads and T & P etc. complete. The exposed frame work & surface shall be polished with mellamine to match with the shade of the VENEER. ( Basic cost of VENEER - Rs 250/sft )

PANELING WITH WALL PAPER :- Providing and fixing Vinyl wall paper on finished surface with adiquate adhesive complete with necessary Hardwood,. as per the detail design including the cost of all materials, labour, overheads and T & P etc. complete. ( Basic cost of WALL PAPER - Rs 200/sft ) (App make :- MARSHAL / EXCEL/ H&H /equivalent )

WOODEN PANELING WITH LAMINATE :- Providing and fixing wooden panelling suitably fixed to the walls with 19 mm thick bwp ply , finished with 1 mm thick texture / suede laminate complete with necessary Hardwood, skirting , mouldings & teak wood beading on the edge etc. as per the detail design including the cost of all materials, labour, overheads and T & P etc. complete. The exposed frame work shall be finished with matt finsish enamel paints / polish with mellamine to match with the shade of the Laminates.

Acoustical Wall Panelling :- LOWER :- Supply & installation of wall paneling of high density fiberboard made out of pure pinewood particles , Fire Resistance - Pink in colour core with 5 test Fire Resistance BS 476 part 5 , BS 476 part 6 , BS 476 part 7 ISO 1182 ASTM E662 Smoke Density - Melamine laminated finish, perforated wooden grooved HDF slats L16-2 (2 mm grooves @ 8 mm centers),tongue-groove edge for a seamless look of linear dimension size 128 mm x 2440 mm x 16 mm thick having density 700 Kg /m3, weight -9 Kgs/m2 with back fleecs from soundtex Germany nonwoven acoustic to be pasted on slats surco is to be installed by using GI strut system. The technical parameters are as follows Core Variants - Fiberboard, Climate (OC RH) – 50, 70 Light reflectance – 75%,Green (RC %) – 25, Hygiene (VoC, Clean room) – Low, Class 1,Strength, Load capacity (Kg) - Anti sag, Ball-Impact. The concealed wall paneling system shall include GI Wall channel (WC25) having thickness 0.45mm, length 3600mm, unequal flanges of 15 & 20mm and web of 25mm should be fixed along the perimeter of the wall with nylon sleeves and suitable fasteners at every 300mm center.

Then fixed Main channels (MC45) having thickness 0.9mm, length 3600mm, equal flanges of 15mm and web 45mm from the side wall & fixed at every 1200mm centers with GI cross channel(CC25) having thickness 0.45mm, length 3600mm, knurled web 35mm, depth of 25mm and equal flanges 9.5mm is fastened to the Main channel in the direction perpendicular to the Main Channel at every 600mm center. The framework will maintain 50 / 75 mm gap from the walls. Now clad the wooden slats surco on the CC 18 with the help of center & edge clips to get better locking of slats. The tongue & groove are to be properly aligned to get flush look . Synth poly fiber PF 5 x 50 wool of 500 gsm to be filled between the horizontal & vertical studs as in filler with the help of wire / stick & adhesive. Test certificate of the use products shall be submitted after procurement of materials The rate shall be including all cost of materials , labour, overheads T & P etc., complete. excluding GST as per the detail design and specification approved by Engineer -in-charge /Architect . (App make :- ANUTONE / AEROCEIL/ ARMSTRONG / NISHABD/ EQUVALENT )

Providing & Fixing Techstyle® or equivalent honeycomb acoustic Wall Panelling / False Ceiling System in White/ Black colour comprises of 1200mm wide x 1200mm long x 28.5mm deep panels having cellular core made from modified glass matt, aesthetic surface is made from FR non woven fabric on glass matt & back surface having inorganic coating on glass matt & The panel shall have NRC value of 0.85 (ASTM C 423) & SAA Value of 0.89 (ASTM C423) including cost of all labour, materials, taxes, royalties, loading and unloading, conveyance, Over head charges, Contractor's profit etc. complete as per the direction of the Engineer-in-Charge. (Make - Haunter Douglas ,Armstrong,Everest / Ecotone)

CARPET TILE FLOORING :- Supplying and Fixing of broadloom carpet of ,100% Nylon Cut Pile , Digitally Printed , Pile Height 7 mm (± 1 mm),Total Height 11 mm (± 1 mm),Stitch / 10 cm 37-39 (± 2% ), Pile Weight Net less Than 800 GSM (± 5% ), Total Weight 1791 GSM (± 5% ), Secondry Backing PP Mesh, Gauge 1/8 Cut Pile, Latex Natural Rubber, Color fastness to LightTest Method: AATCC 16 (20 AFU) ≥ 4.0 at 80 Hours , Static Electricity Test Method: AATCC 134 Less than 3.5 KV, Hexapod test Method: ASTM D 5252 ≥ 4, Flammability (Radiant Panel),Anti Bacterial & Anti Microbial Test Method: ASTM E 648 ≥ 0.45 (Class I) , complete as per drawing , specifications of the architect. The carpet and Underlay (min 6 -8 mm) will be installed with standard SR 998/SR505/MAPAI Adhesives.The flooring to be installed as per the manufacture's specification and to be installed by its authorized agency or as Approved , with minimum 5 Years warrenty from Principal for any manufacturing defects . (App make :- WELSPUN / ROZETA/ CCIL /EQUIVALENT )

Providing and fixing of Wooden fire cum accoustic doors with 32db as per BS:476 Part- 20 & 22 & IS 3614 part-1 & part-2 for stability , integrity and thermal insulation. 03 Criteria Wooden door confirming to IS 277 with the following specification. Recommended fire door shall have doors tested earlier at CBRI for maximum rating of 2hrs tested with or without vision panel. Individual Test certificates should be available for glass used in vision lites confirming the required fire ratings. Any deviation in specification other than what is mentioned in the test certificates are not allowed. Approved manufacturer Navair International Pvt Ltd or equivalent subject to architect’s approval and manufacturer should be ISO & CE Certified & IGBC registered company. Rate should include supply and installation of door and hardware set as mentioned in the door and hardware schedule. Door leaf shall be 83mm thick (75 mm thick with commercial ply + 4mm thick veneer on both side ) fully flush door with or without vision lite. 83mm thick shutter, comprising of 140mm x 90mm hardwood internal timber frame work, with infill of fire resistant & accoustic wool insulation of 48 Kg/m3 density coated with VIPER FRS 881 LH coating on both sides for insulation. The coated insulation shall be sandwiched between HILUX / PAMTECH Non Combustible (Calcium Silicate) Board on both sides (edge to edge on internal Hard wood frame and cladded with 6mm thick commercial ply on both sides, with exposed teak wood beading. 20 x4mm fire & smoke intumescent seal shall be used for shutter & frame . The Frame shall be 140 x 90mm of Hard Wood (Red MIrandi) and coated with VIPER Fire reatrdent Primer.

The rebate shall be of 20mm x 79mm in Door Frame to accommodate the shutter in frame. In all doors, the pasting of the ply and 4mm thick veneer on both side should be done using automatic machine and should be free from any nails or perforations.

Following hardwares are to be provided in Fire cum Acoustic door:

Providing & fitting fixture of Frosted Film For Glass Brand: 3M 3M™ Scotchcal™ Crystal Film Series Material Type: With DIe Cut Shapes Cast Premium Calendered, White With Matt Finish, Thickness: With adhesive: 3.5-4.5 mils (0.09-0.11mm) Glue: Permanent, Pressure Sensitive Acrylic Glue, With Polycoated Craftpaper based Liner as per the approved shade and design Including all cost of labour , taxes T & P etc as per the detail design & specifications approved by EIC .

E.I. WORK Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked Make- Finolex/ Anchor/ Polycab/ HAVELLS/ RR KABLE/ KEI with 20 mm dia HMS FRLS PVC conduit ISI marked Make-AKG/ BEC/ Precision/ Norpak/ Anchor/ Kinjal 6A modular type ( flame retradant type) switch ISI marked Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) ( flame retradant type) Make-Schneider(Zencelo)/ legrand (Myrius) /Panasonic (vision) of suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. . All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. NB:All the electrical,Fire fighting,HVAC,ELV drawings, Technical Data Sheets & make will be approved by SE R& B Electrical circle & CE Building ,Odisha ,Bhubaneswar prior to execution of the work.

Group A

Group B

Group C

Supply and fixing of ISI marked modular type 2nos 6Amp socket with switch on suitable size of metal box and modular cover in front on surface or recess including all conection as per direction of E.I.C. All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. (Make :Legrand(Myrius)/-Schneider(Zencelo)//PANASONIC(VISION)

Supplying,fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket(modular type)(( flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge.. Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision) (For equipement power)All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.

Supplying,fixing of 6A Plug on the separate board with complete fitting by 01 no of 6A switch & socket(modular type)( ( flame retradant type)) with suitable size modular box & cover(anti bactorial & falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a period of 2 years against manufacturing defects against which ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.

Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/ Anchor/ Polycab/ HAVELLS/ RR KABLE/ KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/ BEC/ Precision/ Norpak/ Anchor/ Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 1.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor. In 20 mm dia non metallic heavy duty conduit (LDB to LSB/LIGHT CKT)(2X1.5+1X1.5)

Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/ Anchor/ Polycab/ HAVELLS/ RR KABLE/ KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/ BEC/ Precision/ Norpak/ Anchor/ Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 2.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit.(BDB to LSB/LIGHT CKT/5A PLUG/UPS POINT ) (2X2.5+1X1.5)

Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/ Anchor/ Polycab/ HAVELLS/ RR KABLE/ KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/ BEC/ Precision/ Norpak/ Anchor/ Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 4 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit .(PDB to PSB/ POWER POINT/AC POINT) (2X4+1X1.5)

Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/ Anchor/ Polycab/ HAVELLS/ RR KABLE/ KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/ BEC/ Precision/ Norpak/ Anchor/ Kinjal as required as per direction of Engg.-in-Charge. 4 nos single core 6 sq. mm copper wire for phase and neutral and 02 nos of single core 4 sq. mm copper wire for earth continuty conductor in 32 mm dia non metallic heavy duty conduit.(LFDB TO LBDB/Medical equipement) (4X6+2X4)

Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/ Anchor/ Polycab/ HAVELLS/ RR KABLE/ KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/ BEC/ Precision/ Norpak/ Anchor/ Kinjal as required as per direction of Engg.-in-Charge. 4 nos single core 10 sq. mm copper wire for phase and neutral and 02 nos of single core 6 sq. mm copper wire for earth continuty conductorin 32 mm dia non metallic heavy duty conduit .(LFDB TO FLOOR PANEL TO TPN BDB power) (4X10+2X6)

Supplying and fixing of following mentioned way, three pole/single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3,integrated door earthing system offering additional safety to the user,High quality polyurethane Gasket,the box and cover shall be fabricated to withstand IK09,the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface/recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make-LEGRAND-Ekinox3 DB/ Siemens-Betaguard/ Schneider- Acti 9/ABB ITUS as per direction of Engg.-in-Charge. The Distribution boards should be Replacement Warranty will be 3 years.

4 Way(8+(4x3)+(3x4)) Way TPN MCB DD 7 Segment DB Horizontal Type as per IEC 61439-3 with configuration of incomming I-8 modules,sub incommer-12 module & out going-12 modules,suitable for Flush mounting and Surface mounting with Copper Bus Bar for each phase, with neutral Bus bar, Earth Bar & Cable ties for cable management, prefitted masking sheet, IP43-IK09 with metal door Warranty on DB is 3 years

Supplying and fixing 40 Amps rating,C series,10KA breaking capacity, 2P, 415 volts, RCCB 30mA . Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB FB 200 in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge. . The RCCB should be Replacement Warranty will be 1 year

Supplying and fixing 63Amps 4P 415 volts MCB Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 in the existing MCB DB in the existing MCB DB complete with connections as per direction of Engg.-in-Charge..Warranty on MCB is 1 years.

Supplying and fixing 63 Amps rating,C series,10KA breaking capacity, 2P, 415 volts, RCCB 30mA . Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB FB 200 in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge. . The RCCB should be Replacement Warranty will be 1 year

Supplying and fixing 40Amps 4P 415 volts MCB Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 in the existing MCB DB in the existing MCB DB complete with connections as per direction of Engg.-in-Charge..Warranty on MCB is 1 years.

Supplying and fixing of Type (I +II) 3P+N SPD with Lightening impulse discharge current I imp(10/350) µs 7kA/POLE and 25kA total and maximum discharge current Imax(8/20) msec-50kA,with response time<25 nanosec in the incommer of Distribution board, Make-LEGRAND / Siemens/ Schneider/OBO/Dehn/ABB/ABB in the existing MCB DB with connections as per direction of Engg.-in-Charge.The SPD should have Replacement Warranty will be 1 years.

Supplying and fixing 40-63Amps 2P 240 volts AFDD(arc fault detection device) Make-ABB S ARC1 M/Equivalent model of Schneider/Legrand/Siemens ,10KA,C,IEC-62606 for arc fault in the existing MCB DB in the existing MCB DB complete with connections as per direction of Engg.-in-Charge.Warranty on MCB is 1 year

Supplying and fixing 6 amps to 32 amps rating, 240 volts, C series,10KA breaking capacity, single poles MCB of Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB200 the existing MCB DB complete with connections as per direction of Engg.-in-Charge. .Warranty on MCB is 1 year.

Fittings & Fixtures

Supply ,Installation ,testing and commisioning of suspended Round 50 W LED COB Downlight Dali Dimmable with Recessed mounted Led Luminare pressure die cast Aluminium housing with corrision Resistance powder coated using Nano technology with black powder coated and high transmitive PMMA diffuser having 115 mm Dia, with power consumption Maximum upto 50W having system lumen output of Minimum 5000 Lumen. LED chip life of 50,000 burning hours at L70 - Minimum tested for 10K hours for complaince of TM21 projection. The LED used shall have CCT of 3000K, CRI >80. Luminaire driver should be Isolated and multistage constant current APFC type. Driver should be BIS registered with Input voltage range of 150V to 270V ( nominal rated voltage – 240V) with minimum 6 KV surge protection, PF >0.95, THD <15%; IP 20;. Manufacturer need to submit Following Certificates - 1) LM79 Test report from In-House NABL accredited LAB; 2) LM80 Test certificate from the LED chip manufacturer; 3) Photobiological Safety test report as per IS 16108 : 2012/EN62471 from LED chip manufacturer;.MAKE:WIPRO/ BAJAJ/ LT/PHILIPS/PANASONIC/Crompton/Havells

Supplying an fixing of recess/surface mounted 2'x2' 40 W (595mmx595mmx70mm) square shaped dali dimmable LED with lumen efficacy not less than 120lm/W, CRI not less than 80, CCT of 5700-6500 degree K, THD less than 10%,internal surge protection of 3 KV, complete with Non integrated isolated electronic driver (protects the output /secondary side from any disturbance on the input / primary side ensuring safe operation)and all other accessories suitable for operation on140- 270 V, 50 Hz ,L70 @50,000 burning hrs (5 years warranty) as required as per direction of Engg.-in-Charge (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj) . The luminaire must be Replacement Warranty will be 5years.

Supply and fixing of DALI Controller wireless IoT System having BLE 5.2 AES 128 Bit encyption based 32 channel DALI controller and analog 2 channel (0-10V) output, operates on 100-277 VAC, 10- 30mA, 50Hz, DALI 2.0 protocol. Sensor input of 0-3V DC & 1mA. For analog dimming, It provides output voltage of 0- 10V DC +/- 0.2V and 15mA per channel. For DALI output, it provides 12-20V DC and 160mA max for 32 DALI devices. An auxillary power output of 3.3VDC and 30mA. 0 - 100% dimming, device to device range 45m. Controller must control individually control standard DALI or Tunable DALI Drivers independantly or combination of both. Operating temperature -20 to 50 deg celsius, surge protection 3kV. System shall support easy commissioning and configuration via Mobile Application along with user and site management features. Optional Cloud Application must be available for control and monitoring of the devices along with analytics reports. Mobile Application shall have features of individual & group control for on/off/dimming/ colour tuneing / Scene Control / Animation etc. Device must have security key for commissioning and replacement for future. MAKE: PANASONIC/PHILIPS/BAJAJ/Crompton/WIPRO/HAVELLS/LT

i-Sense BLE 5.2 AES 128 Bit encyption based wireless battery powered 5-button wall switch that controls ON/OFF, intensity and CCT of an individual or group of luminaires.Operates on 3V DC input voltage in an ambient temperature of 0 to 50 deg celsius and device to device range 45m. System shall support easy commissioning and configuration via Mobile Application along with user and site management features. Optional Cloud Application must be available for control and monitoring of the devices along with analytics reports. MAKE: PANASONIC/ PHILIPS/ BAJAJ/ Crompton/ WIPRO/HAVELLS/LT

SITC of 2W/mtr profile RGB LED light with extruded Aluminium housing material, 12/24V in complete as per direction Eng-in-charge.Make-Leksa/Canara/PANASONIC/ PHILIPS/ BAJAJ/ CROMPTON/ WIPRO/ HAVELLS/ LT

SITC of extruded black powder coated Aluminium housing 2W/ mtr step light with provision for LED strip with diffuser, provision for illuminated seat numbering on both sides, rubber grip, vertical screwing ,12/24V in complete as per direction Eng-in-charge.Make-Belight/Illumax/Equivalent

SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 20 watt and lumen output not less than 2200 lumen complete with electronic driver and all other accessories with diffuser having 2 years warranty i/c connection etc as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 2 years .

Supplying and fixing of Energy efficient surface /recess mounted square /round shape 18 W LED luminaire of dimension of consists of white powder coated , die-cast Alluminium housing with high quality frosted diffuser for glare-free uniform lighting distribution with wattage not more than 18 watt and lumen output of 1800 lumens, , CRI not less than 80,CCT of 6000 degree K,THD less than 10%, with electronic driver, internal surge protection of 3 KV , L70 B50: 50000 hrs and all other accessories suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj).The luminaire should be Replacement Warranty will be 2 years

Supplying, installation, of exhaust fan of heavy duty 300 mm sweep 1400 rpm 1700 cmh air delivery with louvers of exhaust fan in the existing wall, including fixing & conntection complete etc.as required and as per the direction of E.I.C..(Make-USHA / /Havells/ ALmonard/ Crompton/Orient/Bajaj

Supply, delivery, installation and testing of following Sweeps of High Speed Energy Efficient wall FAN 600 MM Air Delivery Wall Fan Motor Speed: 1440 RPM Power Consumption: 180 W Blade Sweep Size: 600 mm Number of Speed Settings: 1 Material: Metal..Dominarie wall Fan complete with Canopies & Capacitor etc. including supply of Sundry Materials, making connection from the suitable point outlet complete as required and as per the Direction of Engineer-In-ChargeMake-USHA /Havells/ ALmonard/ Crompton/Orient/Bajaj

LAND SCAPE LIGHT

Supply, installation, testing and comissioning of 4meter long decorative lighting pole with designer single arm bracket and supplied with 3000K ,50-60W LED Pendent Light of die cast aluminium body & clear acrylic diffuser having system lumen output >=120Lm/W protected with IP 65, SDCM≤3. Pole shall be made up of Mild Steel Body with decorative cast aluminium base of minimum 4000mm height and decorative bracket. Pole shall be coated with zinc rich primer & pure polyester powder coating of black with gold embellishment finish. Pole dia will be Ø88.9mm and having base Plate Ø230 x12mm thick with provision for founation bolt. Pole is Compatible for Ø70mm size for cable entry & exist. Junction Box service door is made up cast aluminium and the control gear tray only is prewired with 2.5sq mm cable, 6A SP MCB and 32A 4pole terminal connector for loop-in loop-out arrangement with all materials & labour as required as per the direction of Engineer-in- Charge. (Make: K -lite Pelican mini Orna Bishop Series Pole KP-12016+KL-24897/ Homdec HL-MSP305-PBKT165-1-2358/Equivalent model of RR Ispat/Bajaj/Valmont/Utkarsh/Vakrangee).

Supplying,laying of 3cx2.5 sq.mm copper flexible cable with insulated cover of reputed make,ISI marked with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials

Providing and fixing 6SWG dia GI wire on surface or in recess for loop earthing as required as per direction of Engg.-in-Charge.

Supplying and laying of one number PVC insulated armoured and PVC sheathed XLPE AL. conductor power cable of 1.1 KV grade POLYCAB/FINOLEX/HAVELLS/KEI/RR Kabel/Gloster of following size cables as per direction of Engg.-in-Charge.Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials

4 core x 4 sq mm (for small power/LIGHT TO POLE)

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge.

FAÇADE LIGHTING

Supply, installation, testing and commissioning of Colour Changing 64W RGBW surface mounted Narrow/Medium beam luminaire suitable for outdoor applications of Facade Lighting,Luminaires should be enabled with high power LEDs, should consists of anti-aging and anti-UV high optical efficiency temperature-resistant lenses, suitable for architectural lighting as per design requirement.Luminaire should have inbuilt DMX Chip and can be Controlled through DMX/Ethernet protocol using 8 bit DMX 512 Controller, Controller can achieve 16.7M colors. Luminaire should be complete with dedicated lens for each LED. DMX enabler circuit should be inside luminaire only.The luminaire should be complete with dedicated Lens for each LED and should have options for various beam angles, actual will depend on the design by the contractor and site requirement.Luminaire should be provided with suitable integral/separate non-integral power supply unit.Lumen maintenance of at least L70B50 @ 50000 BH (Ta-25°C).The luminaire should have Aluminium Die cast housing powder coated in Shiny Grey with minimum 3-4 mm thick : Toughened Glass.Ingress Protection ≥ IP 66, Impact resistance level ≥ IK 08. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +45°C, Operating Humidity : 10%-90% . THD should be less than 10%.Built in Surge protection : DM 4kV CM 6KV .Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements.Connectors should have IP67 male/female connectors for DMX through wiring.The LED Luminaires and drivers should be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.LM79 and LM80 reports must be submitted. Make of LED must be validated through LM-79 for each type of fitting. Color rendering index ≥ 80 and power factor of complete luminaire ≥ 0.90, at white colour.The luminaire manufacturer must be having registered office and having service set up (Toll free base number to be provided )in the state to provide after sales service within 5 years warranty period. Make : Colour Kinetics/Leksha lighting/LT/Canara Lighting/Havells/K-Lite

Supply, installation, testing & commissioning of 24W-30W RGBW LED SPOT LIGHT /Linear Wall Washer with following technical features: Aluminium Die-casting body with Surface anodic oxidation and UV stabilized toughened glass front cover, luminary should be linear shaped suitable for illumination of wall facade lighting, Tilt : asper site requirement, IK08 and IP-66 or greater ingress protection for outdoor application suitability,secondary optical lenses provided on each LED of fitting with suitable narrow beam angle, DMX compatibility with inbuilt decoder. Control Mode: DMX512, DMX Controller can achieve 16.7M colors, Rated Input Supply of LED: Highly reliable DC 24V constant voltage power supply which drives the RGBW LEDs High Power LED Power Consumption : 24W to 30W (approx.) per fixture however as per requirement wattage may be increased /decreased to meet the desired effect of Façade. Power Efficiency : >85%, Power factor : >0.9, Operating Frequency: 50 Hz, Operating temperature: -10 to +45 degree centigrade, Life Span : >50000 hours, Product test reports: LM79 & LEDs test report- LM80 shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. The luminaire manufacturer must be having registered office and having service set up (Toll free base number to be provided )in the state to provide immediate after sales service within 5 years warranty period. Make : Colour Kinetics/Leksha lighting/LT/Canara Lighting/Havells/K-Lite

Accessories -Supply,Laying,Connecting, Testing & Commissioning Jumper Cable - Luminaire to Luminaire

Power Supply - 100W , 24V DC , IP65, BIS

Power Supply - 350W , 24V DC , IP65, BIS

Supply, installation, testing and commissioning of PROGRAMMING & Controller capable of delivering light shows to installationswith up to 2048 unique light addresses. Software light show authoring software along with controller shouldadd new levels of sophistication and flexibility to lighting installations while eliminating the need forexpensive lighting boards and technical programming expertise. It should be compatible for programmingwith PC. There should be provision of MicroSD card. OS requirement for the controller is Windows 7/8/10 or latest version. Easy to use with factory preset shows, custom show-authoring capabilities, an intuitive LCD interface,removable SD card storage, and on board light addressing features, controller should enable to spend more time on the creative aspects of lighting design and less time on setup.Packaged with software should light show authoring software—software should give the flexibility to create and manage light shows using fully customizable effects, multi-track editing, timeline layering, and transition styles.The controller should have variety of features including 1024 DMX channels, Ethernet facility, dry contact port triggering and multi zone SD card memory.Control 12 DMX universes—controller should have 4 DMX output ports, each controlling a universe of 512 DMX channels. The luminaire manufacturer must be having registered office and having service set up (Toll free base number to be provided )in the state to provide immediate after sales service within 5 years warranty period. Make : Colour Kinetics/Leksha lighting/LT/Canara Lighting/Havells/K-Lite

DMX Slave/ Booster should have a suitable output 8 port DMX/RDM splitter with DMX/RDM pass-throughsupporting bi-directional communications for discovery, addressing and DMX control of Architectural lighting products.The unit should take the incoming DMX/RDM signal and split the signal into suitable separate output channels allowing for expanding the number of devices controlled from 32 to 6 X 32 or as per design / site requirement.The output terminals should electronically & optically isolated from the input & RDM-through port and share a common ground reference. All output ports should have an independent output driver to boost the DMX/RDM signal. Splitters should be capable to amplify the DMX signal & allowing the data link to be extended by max 70 m (230 ft). DMX/RDM Splitter/ Booster, Isolated DMX/RDM Input/Outputs Surface or DIN-rail mountable & AC adaptor included and it should be compatible with façade lighting products. Make : Colour Kinetics/Leksha lighting/LT/Canara Lighting/Havells/K-Lite

Supplying,fixing of perforated cable trays with horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 200mm(W) of MAKE- Profab/ OBO/ Neidax.The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge.

Supplying,fixing of perforated cable trays with horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 300mm(W) of MAKE- Profab/ OBO/ Neidax. The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge.

Supplying,fixing of perforated cable trays with horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 400mm(W) of MAKE- Profab/ OBO/ Neidax. The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge.

MAIN PANEL

S/I/T&Commissioning of CPRI tested LT indoor floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by siemens gray powder cote paint fallowed by 9 tank acid treatment is designed as G.A drawing as per direction of Engg.-in-Charge.Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.80X10MM Separate Aluminium Earth bus bar should be installed.Detailed GA drawing of the Panel, control wiring and power wiring drawing are to be submitted to SE Electrical Circle(R&B) and CE Bdgs O bbsr before execution of the work. All the feeders shall have ON/OFF/TRIP indication. In commer-1-01 number of 800A 4P MCCB with ROM 36kA with adjustable Micro processor Release with Ics=100% Icu. (make- -LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB formula)with shunt trip.with axulary for BMS ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula (FROM Transformer) Changeover-01 number of 630A 4P changeover switch ( Make-LEGRAND/ Siemens/ Schneider/ABB) Busbar- 04 numbers of 900Amps Aluminum busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing) Out going- 3 numbers of 250A 4P MCCB,,25Ka MCCB with TMR based release with adjustable overload ,Icu=100%Ics( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula) 5 numbers of 100A 4P MCCB, 25Ka MCCB with TMR based release with adjustable overload ,Icu=100%Ics( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula) 3 numbers of 125A 4P MCCB, 25Ka MCCB with TMR based release with adjustable overload ,Icu=100%Ics( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula) 4 numbers of 63A 4P MCCB, 25Ka MCCB with TMR based release with adjustable overload ,Icu=100%Ics( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula) Instrument- (i) 06 numbers phase indicating lamp with toggle switch & HRC fuse. (ii) Digital type multifunction meter for voltage,current,frequency,PF,THD indication with RS 485 COMPACTIVITY FOR bms data for all the incoming and outgoing feeders. 2 no. 3P+N 65kA type 1+2 SPD with 63A rating,10KA breaking capacity ,4P MCBMake-LEGRAND / Siemens/ Schneider/ABB/OBO/Dehn/ABB

HVAC PANEL :S/I/T&Commissioning of LT HVAC Outdoor DOUBLE DOOR panel made out by 2mm CRCA steel sheet duly derusted & painted by siemens gray powder coat paint fallowed by 9 tank acid treatment process . Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.40X10MM Separate Aluminium Earth bus bar should be installed. Detailed GA drawing of the Panel, control wiring and power wiring drawing are to be submitted before execution of the work. All the feeders shall have ON/OFF/TRIP indication. In commer-01 number of 250 A 4P Icu=100%Ics,25Ka with TMR based release with adjustable overload ,Icu=100%Ics( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula) Busbar- 04 numbers of 300AmpsAluminum busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing) Out going- 07 numbers of 40A 4P RCBO 300 MA ( Make-LEGRAND/ Siemens/ Schneider/ABB ) Out going- 02 number of 125A 4P MCCB 16Ka MCCB with TMR based release with adjustable overload ,Icu=100%Ics( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS) Instrument- (i) 03 numbers phase indicating lamp with toggle switch & HRC fuse. (ii) 1 set of digital type multifunction meter with CTs 250/5A 3 nos class 1 type(Make-KAPPA /AE) for voltage,current,frequency,PF,THD indication with RS 485 COMPACTIVITY FOR bms data. 1 no. 3P+N 40kA type 2 SPD with 63A rating,10KA breaking capacity ,4P MCBMake-LEGRAND / Siemens/ Schneider/ABB/OBO/Dehn/ABB

FLOOR LIGHT PANEL(2 Nos.) and UPS Outgoing panel(1 no.) : S/I/T&Commissioning of LT indoor floor mounted cubical type electrical main panel (for both light circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing.as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.. 20X10MM Separate Aluminium Earth bus bar should be installed. All the feeders shall have ON/OFF/TRIP indication. In commer- 01 no 100A 4P MCCB 16kA with TMR based release with adjustable overload ,Icu=100%Ics( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula) Busbar- 04 numbers of 150Amps Aluminum bus bar Electrolytic Aluminum busbar duly sleeved by color coded PVC sleeve & supported by suitable size DMC insulator. Out going- 04 nos 40A 4P MCB 10kA,C series Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB200 Instrument- (i) 03 numbers phase indicating lamp with toggle switch & HRC fuse. (ii) 01 set of 0-100Amps Ammeter with CTs 100/5A 3 nos class 1 type(Make-KAPPA /AE).(DIGITAL)(Sicure/L&T,CT-KAPPA or equievalant make & model) (iii) 01 set of 0-500 voltmeter .(DIGITAL)(Secure/L&T or equievalant make) 1 no. 3P+N 40kA type 2 SPD with 63A rating,10KA breaking capacity ,4P MCBMake-LEGRAND / Siemens/ Schneider/ABB/OBO/Dehn/ABB

FLOOR POWER PANEL : S/I/T&Commissioning of LT indoor floor mounted cubical type electrical main panel (for power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing.as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.. 20X10MM Separate Aluminium Earth bus bar should be installed. All the feeders shall have ON/OFF/TRIP indication. In commer- 01 no 125A 4P MCCB 16kA with TMR based release with adjustable overload ,Icu=100%Ics( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB FORMULA) Busbar- 04 numbers of 200Amps Aluminum bus bar Electrolytic duly sleeved by color coded PVC sleeve & supported by suitable size DMC insulator. Out going- 04 nos 63A 4P MCB 10kA,C series Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB200 Instrument- (i) 03 numbers phase indicating lamp with toggle switch & HRC fuse. (ii) 01 set of 0-200Amps Ammeter with CTs 100/5A 3 nos class 1 type(Make-KAPPA /AE).(DIGITAL)(Sicure/L&T,CT-KAPPA or equievalant make & model) (iii) 01 set of 0-500 voltmeter .(DIGITAL)(Secure/L&T or equievalant make) 1 no. 3P+N 40kA type 2 SPD with 63A rating,10KA breaking capacity ,4P MCBMake-LEGRAND / Siemens/ Schneider/ABB/OBO/Dehn/ABB

STAGE PANEL:S/I/T&Commissioning of LT indoor floor mounted cubical type electrica panelmade out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing.as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.. 20X10MM Separate Aluminium Earth bus bar should be installed. All the feeders shall have ON/OFF/TRIP indication. Incomer:125 A 4P MCCB (16 KA) with adjustable thermal setting Ics = 100% of Icu Bus bar: 4 nos. 200 A Aluminum Busbar duly sleeved Outgoing: 8 Nos 40A DP MCB. (10 KA) ,C series and 4 nos. 32A FP MCB , C series Instruments: 1 set.LED type phase indicating lamps with control fuses Complete duly factory wired as per SLD and panel should have proper earth by suitable rated Aluminium flat earthing studs as per specification mentioned below duly factory wired conforming to the relevant ISS as per the direction of Engineer-in-charge..MAKE OF MCCB- LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB FORMULA Make of MCBs- LEGRAND-DPX3/Siemens-Betaguard-Schneider-Acti-9/ABB SB200

SITC of LT indoor floor mounted cubical type lift panel made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder coated paint is designed as G.A drawing. (FOR LIFT)as per direction of Engg.-in-Charge. Warranty period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.Type 2 SPD(3P+N) 40ka with 63A 4P,C series, 10kA shall be installed in the incomer. 20X10MM Separate Aluminium Earth bus bar should be installed. 63amp panel board having 63A Amp 16KA 4P MCCB TMR based release with adjustable overload ,Icu=100%Ics as incommer, 100 amp electrolyte aL bus ba-1 Set, 63A Amp 4P RCCB 30mA- 1 No,25A Amp DP RCCB 30mA- 2 No,6-32A DP MCB 10ka, c series -2 No as Outgoing with ampere meter, voltmeter, toggler switch,three nos led indicator,Drum insulator,transparent isolation glass,danger Board and Rubber Mat as per the direction of site engineer in charge (make of mccb :-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB FORMULA) Make of MCB-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB200(Lift Panel)

40 KVA UPS

Supply ,installation ,testing & commissioning of 40KVA UPS SYSTEM WITH IGBT based inverter system, true online double conversion system, inbuilt isolation transformer & automatic phase sequence corrector of 3ph in put to 3 ph output,415V, with built in BMS with battery back up up to 30 minutes with MS Rack for battery Housing, DC cable 7 Mtr with SFU and links for installation (Battery required: 12V, 100AH, 40 No.s) protection for fault by OL,UV,EF,GF,OC,Ph. (Make:Numeric/APC/ Vertiv/) LOAD OF LIGHT , as per direction of Engg.-in-Charge. Warranty period of all accessories & component & system must be 2 years & complete test certificate must be submitted along with ups including component list & SLD.

Supplying of one number PVC insulated armoured and PVC sheathed XLPE property AL. conductor power cable of 1.1 KV grade Make- Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster of following size cables as per direction of Engg.-in-Charge.

3.5 core x 300 sq mm Aluminium armoured Cable.(FOR Main PANEL)

3.5 core x 240 sq mm Aluminium armoured Cable.(FOR DG incomer)

3.5 core x 185 sq mm Aluminium armoured Cable.(FOR HVAC / OTHER PANEL)

3.5 core x 50 sq mm Aluminium armoured Cable.(FOR FLOOR PANEL)

3.5 core 25 sqmm Aluminium armoured Cable (LIFT )

3 core 2.5 sqmm control copper armoured Cable (auditrioum light)

4 core 16 sqmm Aluminium armoured Cable External light)

5 core x 10 sq mm COOPER armoured Cable

Supplying and making end termination with brass double compression gland and aluminium lugs for following mentioned size cable.

3.5 core x 300 sq mm brass double compression gland and aluminium lugs

3.5 core x 240 sq mm brass double compression gland and aluminium lugs

3.5 core x 185 sq mm brass double compression gland and aluminium lugs

3.5 core x 50 sq mm brass double compression gland and aluminium lugs

3.5 core x 25 sq mm brass double compression gland and aluminium lugs

5 core x 10 sq mm brass double compression gland and aluminium lugs

4 core x 16 sq mm brass double compression gland and aluminium lugs

EARTHING

Supplying,installation,testing & commissioning Of Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc (WITH charcoal and salt) as required as per direction of Engg.-in-Charge.

Providing and fixing 25 mm X 5 mm GI strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supply and fixing of shock treatement charts duly laminated along with separate colour single line diagram laminated, to be fixed in Electrical control panel room.

Supply and fixing of first aid box with medicines complete with medicine with three years expiry date to be fixed in Electrical control panel room..

Supplying of following Materials.

Supply installation of 33kV 3mm thick Class-C Rubber Mat as per IS-15652 and complete as per direction of Eng-in-charge.(Size-10mx1m)

Danger Board.

Lightning Protection :- Supply of 8 mm Aluminum Round Conductor.Tested as per IEC 62561. as per direction of engineer in charge. Make-OBO/Dehn/ABB

Supply of Roof conductor holder for parapet- Polyamide Conductor holder:With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance.Tested as per IEC 62561. as per direction of engineer in charge. Make-OBO/Dehn/ABB

Supply of Polyamide roof cable holder for flat roof: DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance. Tested as per IEC 62561. Make-OBO/Dehn/ABB

Supply of Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Tested as per IEC 62561.(2nos/expansion piece). Make-OBO/Dehn/ABB

Supply of 1 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305. Tested for Electrical , mechanical and chemical as per IEC 62561. Tested for 100kA lightning current. Make-OBO/Dehn/ABB

Supply of Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 3 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. Tested as per IEC 62561. Make-OBO/Dehn/ABB

Supply for Providing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete and clamp tested upto 100KA lightning current . Make-OBO/Dehn/ABB

Supply for Providing of Stand for Fang Fix system 16 kg made up of frost resistant concrete. Make-OBO/Dehn/ABB

Supply of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by 30x3 mm GI strip as specified in drawing and directed by Engineer. Tested for 100kA lightning current. Make-OBO/Dehn/ABB

Supply of IP 66 Poly Propylene Junction Box. Installation at 1Mtr Height For Test Joint .Internal dimensions: 100x100x48 mm. Make-OBO/Dehn/ABB

Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized. Tested as per IEC 62561. Make-OBO/Dehn/ABB

Supply for Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. Tested for 100kA lightning current. Make-OBO/Dehn/ABB

Supply of flat conductor holder- Fit: FL 30, With mounting hole 6.2 x 22 mm, With 2 cylinder bolts M6 x 16 and over-piece from hot-dip galvanised steel, Bottom section from polyamide, black. Tested as per IEC 62561. Make-OBO/Dehn/ABB

Supply for Providing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric. Make-OBO/Dehn/ABB

Supply of UL Listed maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 17.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2. Make-OBO/Dehn/ABB

Supply of universal clamp made of SS to connect rod with flat conductor. Make-OBO/Dehn/ABB

Supply of Earth conductivity enhancing mineral compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested. Make-OBO/Dehn/ABB

Supply of The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system. Make-OBO/Dehn/ABB

Installation of The above arrangements including all accessories as per Direction of Engg. In charge.

SIGANGE LOGO

Supply, installation, Testing, Commissioning of LED Sign Board as per below specification of Box type Display Matter:- 1.SIRD AUDITORIUM (English Letter Red Color) Letter Height 24 Inch. 2.Odiya Letter Red Color Letter Height 18 Inch 3.Government of Odisha Logo (24X24 Inch) ACP Sheet:- Aluminum based cover panel sheet(ACP) Outdoor type 3 mm (Viva, Alomax, Imperia Décor, Citi Bond ) Supporting of English Letter. Plastics Sheet: - 3mm Plastics Sheet (Yalow, Red) Color & Rasing of 2.5 inch.(Gray) (Acast, Malasia Imprated) L.E.D :- 0.3 to 1.5 Watts (Yalow, Red) Color (Samsung, GE, Osaram, Philips, LG) Imported. Power Supply: - SMPS (Switch mode Power Supply), RPS (Regulate Power Supply).In put Voltage 160 to 230 A.C./ Out put Voltage 12/24 Voltas D.C. (Samsung, GE, Osaram, Philipes, LG) Importaed. Silicon Past: - Silicon Past past of the ACP sheet

Supply,Installation, Testing & Commissioning of of 15 Passenger lift gearless with Machine room Capacity,Elevator G+1 Floors (Shaft size should not be less than-1850mm(Left to right)x2500mm(Front to back)) (Min. Car size-1500mmx1600mm) with ACVVVF drive/Control for constant load of 1020 kg ARD >=1.25 MPS SS honeycomb interior ,2hr fire rated door with simplex operation without attendant car position indicators,battery operated alarm bell & emegency light,SS honeycomb finish door finished car interior, recess Granite flooring ,power operated centre opening automatic sliding SS honeycomb finish doors for car entrance & hoist way entrance etc .All SS materials shall be of grade SS-304 with thickness not less than 1.6mm. Machine beams,buffer support channels,facia plate including sills pit ladder metal screen in Elevator pit etc.as per specifiaction including cost of (i)Overload detection,(ii)Voice announcement,(iii) Intercom,(iv)Braille Buttons (v) flat cat 6 cable for CCTV with all Civil & Electrical works required for installation of Elevator in the existing lift well and machine room,scaffolding ,floor cutting including Fireman's switch complete in all respect.The Elevator should be suitable for physically handicapped person. (Make:OTIS/Mitsubishi/Johnson/Schindler)

HVAC WORK Inverter based VRV/ VRF System

Outdoor Units

Supply,Installation, Testing and Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling only, having all hermetically sealed inverter type Scroll/Twin rotary Compressor(s) microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. The unit shall deliver the rated capacity at AHRI Conditions and work even at 49°C ambient temperature without tripping. The unit shall be suitable to work on 380-415 V, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. MS/GI powder coated stand with vibration isolation pads. The ODU shall have low noise condenser fans with external static pressure of the outdoor unit shall be more then 75 Pa to avoid hot air recirculation, auto address setting, automatic refrigerant charging,auto check function for connection error and complete with indoor and outdoor units with individual controller and with fittings etc. .The Unit should have free phase technology so that unit can work in case of phase reversal also without tripping of units.COP at 100% load should greater than or equal to 4.Make: Mitshubishi/ TRANE/O-GENERAL/Diakin

SITC of AHU connecting kit with other accessories as per the direction of Engineer-in-charge.

Supply, Installation,Testing and Commissioning of following minimu capacity 4-way/ VRV Cassette Type Indoor ceiling mounted unit equipped with cord less remotes & refnets , synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, drain pan, drain pump, cassette grill, insulation, necessary supports, vibration isolation etc, suitable for operation on 230 V ± 10%, 50 Hz single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire. All indoor Units should have force shut option to connect with fire alarm adaptor, so that the unit automatically stops in case or fire. The cooling capacity of indoor unit will be at air inlet conditions of 27 degree C DBT and 19 degree C WBT. Make: Mitshubishi/ TRANE/O-GENERAL/Diakin

Supply, Installation,Testing and Commissioning of following minimu capacity Ductable Type Indoor ceiling mounted unit equipped with cord less remote & refnets, synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, drain pan, drain pump, cassette grill, insulation, necessary supports, vibration isolation etc, suitable for operation on 230 V ± 10%, 50 Hz single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire. All indoor Units should have force shut option to connect with fire alarm adaptor, so that the unit automatically stops in case or fire. The cooling capacity of indoor unit will be at air inlet conditions of 27 degree C DBT and 19 degree C WBT. Make: Mitshubishi/ TRANE/O-GENERAL/Diakin

36TR 12500 CFM 6RD, ESP-80MM, FM AHU

SITC of 12ft length x12ft width x 10ft height GI shed for AHU as per direction of Engineer-in-charge.

Supply,Installation,Testing & commissioning of centralised I-Touch Manager indoor units. This should be Touch screen type with necessary adaptors .Make: Mitshubishi/ TRANE/O-GENERAL/Diakin

Refrigerant Piping

Supply & Installation of interconnecting following sizes of refrigerant copper pipe work of following outer diameter, insulated with 25mm thick closed cell electrometric Nitrile rubber tubular insulation between each set of indoor & outdoor units . The pipe dia upto 25 shall be soft seamless & above 25mm dia shall be hard seamless . All piping inside the room shall be properly fixed/supported with suitable size of clamp/ M.S. hanger and all external piping shall run in GI. cable tray etc. as reqd. Make of insulation-K Flex/Armacell/Vidoflex/Eurobatex/Isoline Make of pipe-Rajco/Mandev

41.3 mm with 1.43 mm thick

34.9 mm with 1.21 mm thick

28.6 mm with 1.00 mm thick

22.2 mm with 0.8 mm thick

19.1 mm with 0.8 mm thick

12.7 mm with 0.8 mm thick

15.9 mm with 1.00 mm thick

9.5 mm with 0.8 mm thick

Supply & Installation of interconnecting following sizes of refrigerant copper pipe work of following outer diameter, insulated with 25mm thick closed cell electrometric Nitrile rubber tubular insulation between each set of indoor & outdoor units . All external piping(which are exposed to external environment such as terrace etc.) shall be provided with factory laminated GC Cloth & then shall run in perporated hot dip galvanized GI. cable tray with cover etc. as reqd. Make of insulation-K Flex/Armacell/Vidoflex/Eurobatex/Isoline Make of pipe-Rajco/Mandev

41.3 mm with 1.43 mm thick

19.1 mm with 0.8 mm thick

Drain Piping

Providing & fixing of PVC Pipe complete with fittings, supports as per specifications and duly insulated with 9 mm thickness Class O of closed cell nitrile rubber/XLPE as per direction of Engineer-in-charge & specifications enclosed as reqd.

50 mm dia

40 MM dia

32 mm dia

Control & Transmission Wiring

Providing & fixing control cum transmission wiring of 2 core x 1.0 sqmm shielded copper cable in suitable conduits between indoor and out door unit.

Gas Charging for the entire circuit(R410A)

Air Distribution

Supply, Manufacturing, fixing,testing and commisioning of GI ducting complete with supports,dampers etc.as per specifications. Make-TATA/SAIL/JINDAL

22 Gauge

24 Gauge

Insulation work

Supply,installation,testing and commissioning of duct thermal insulation of Following Capacities , Make of insulation-K Flex/ Armacell/ Vidoflex/ Eurobatex/ Isoline with 25mm thick Nitrile Rubber with factory laminated GC CLOTH to provide the sufficient mechanical protection. The fibre glasscloth shall be factory laminated. The adhesive shall be SR 98 or equivalent sourced from OEM of nitrile rubber insulation.

Supply ,& Fixing of Accoustic Insulation 15 mm thick of Armasound open cell nitrile rubber

Supply ,& Fixing of Flexible canvas connection

Supply, erection, testing & commissioning of Aluminium powder coated grills/diffuser with VCD having flange all around.Make-Glenstorm/Airflow/Systemaire

Supply, erection, testing & commissioning of Aluminium powder coated grills/diffuser without VCD having flange all around.Make-Glenstorm/Airflow/Systemaire

Supplying,fixing of hot dip galvanized GI perforated cable trays with cover having horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 450mm(W) of MAKE- Profab/OBO/Neidax.The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge.

SITC of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc., Make-systemair/ventech/Air master/Ruskin Titus

SITC of Fusible link mechanical fire damper complete with sleeve for fixing on retrun air opening.The damper shall be spring loaded and suitable for reset to original position.The damper also be provided with limit switch for transferring the signal to AHU starter panel/BMS for tripping the AHU in case of fire .The rate shall be inclusive of control wiring upto the Starter panel/DDC clopsing the opening surrounded by the sleeve with fire glass and fire sealant as per standards Fire Damper.Make-systemair/ventech/Air master/Ruskin Titus

VENTILATION FANS

Supply, Installation, Testing and Commissioning of Propellor Fan suitable for 1~, 230V, 50 Hz power supply. MAKE - SYSTEMAIR/GREENHECK/ELTA

Supply, Installation, Testing and Commissioning of Duct mounted Single skinned Circular Inline Centrifugal Fan for Toilet Ventilation with direct driven Backward-curved impellers.The Fan has external rotor motor suitable for 1~, 230V, 50 Hz power supply. MAKE - SYSTEMAIR/GREENHECK/ELTA

1000 CFM @ 15mm MMWG static pressure

Installation, Testing and Commissioning of pressurization Axial Fan. Direct driven fan shall be AMCA certified for both Air and Sound performance. The fan shall be equipped with mounting bracket, inlet guard & spring isolators for the installation of the fans. Fan casing to be made from either galvanized steel with a coating of Z275 or mild steel that is hot dipped galvanized to DIN EN ISO 1461. The propeller shall be both statically and dynamically balanced in accordance to AMCA Standard 204-05. Fan total efficiency should not be less than 70%, noise level should not be more than 80 dB(A) @ 3m distance when measured in hemispherical reverberant room conditions. Use of Sound attenutors to achieve the desired sound level is not acceptable. Motors shall be VFD Compatible, sqirrel cage, TEFC, IP55, single speed, continous duty, IE2 efficiency in accordance with IS 12615, suitable for 415+10% volts, 50 cycles, 3 phase AC supply. The cost is inclusive of Starter panel. MAKE - SYSTEMAIR/GREENHECK/ELTA

6000 CFM @ 25mm MMWG static pressure

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN Low-Light IR Fixed Lens Dome/Bullet Camera, 1/2.8" CMOS or better, 5MP (2592 x 1944) @ 25fps or better, triple stream at various resolution & Frame Rates, Min. Illumination required 0.007 lux (color), 0 Lux IR On, 2 IR LEDs, Smart IR with upto 50m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/8 - 1/30,000; Adavance Video Compression technology such as H.265, H.264 & MJPEG , Fixed Lens 2.8mm, Field of View FoV H:90°, V:62°, BLC, HLC, WDR, 3DNR, White Balance - Auto/Manual, Minimum Edge Intelligence Video Analytics : Video Motion Detection, Tampering, Loitering, Intrusion, & People Counting, 4 Privacy Mask, 8 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 2-Way Audio Full Duplex Line IN/Out, 256GB SD card support, Alarm: 1In/1out, PoE (802.3 af) and 12V DC, Max 5W, IP 66/67 & IK10 with Die Cast Aluminium Housing, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S/G/T compliant,, CE (EN 50130-4), FCC Part 15, EN 55032 & RoHS (EN63000)/NDA/STQC compliant. Make-Honeywell(Series 50), Pelco, Axis,Bosch

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN Low-Light IR motorized Lens Bullet Camera, 1/2.8" CMOS or better, 5MP (2592 x 1944) @ 25fps or better, triple stream at various resolution & Frame Rates, Min. Illumination required 0.007 lux (color), 0 Lux IR On, 4 IR LEDs Smart IR with upto 50m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/8 - 1/30,000; Adavance Video Compression technology such as H.265 & H.264 High Profile & MJPEG , Triple stream, Fixed Lens 2.8mm, BLC, HLC, 3DNR White Balance, Minimum Edge Intelligence Video Analytics : Video Motion Detection, Tampering, Loitering, Intrusion, & People Counting, 4 Privacy Mask, 8 Region Of Intreset, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, Dual channel Audio, Alarm: 1In/ 1out, 256GB SD card support, PoE (802.3 af) and 12V DC, Max 6W, IP 66, IK 10 vandal proof with Die Cast Aluminium Housing, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S/G/T compliant, CE (EN 50130-4), FCC Part 15, EN 55032 & RoHS (EN63000)/NDA /STQC compliant.Make-Honeywell(Series 50), Pelco, Axis,Bosch

Supply , Installation, testing , commissioning of 32 Channel NVR with 4 SATA; 384 Mbps incoming bandwidth, Up to 8 Megapixels Resolution Display and Recording, H.265 video compression technology with real time encoding, Full function CMS (Central monitoring software) supported, Two way audio supported, Dual streaming technology to encode recording stream and network stream separately, Supports remote monitoring on Mobile Client (Android, IOS), TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP, Time/ Date, Alarm, Motion Detection & Exact Search (accurate to second), Record Snapshot, FTP, Preset Calling, Email notification supported, Manual/ Alarm/ Motion Detection/ Continuous, CE, FCC, RoHS).STQC compliant Make-Honeywell series 50/Pelco/Axis/Bosch

Supply, Installation,Testing & Commisioning of Surveliance 10 TB HDDMake:- WD/Segate/Toshiba

SITC of 55" UHD IPS Commercial Digital Display for Small Size Discussion & Chambers: Brightness (440 nits or higher), Dynamic Contrast Ratio (Dynamic MCI (Hz)):1000000:1), 1000000:1, Static (Panel) Contrast Ratio-1200:1, Response Time (G to G)-8 ms, Refresh Rate.-60 Hz, Life span (hrs)-30,000, Speaker (Sound Output):10W + 10W, Speaker System: 2.0 ch, DVB-T2/C Broadcasting System, Commercial Smart UX, webOS version (webOS 6.0), BIS Certification with 3 years onsite warrenty. Make: LG/Samsung/Sony

SITC of 4 pair Cat6 23 awg U/UTP LSZH Cable in the existing surface/ recessed steel/ PVC conduit as required: The 4 pair Unshielded Twisted Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must,Insertion Loss of 32.8 db/100m at 250 MHz ,Cable should support operating temperature from -20° to +70°C Cable support Conductor Resistance ≤ 9.38 Ω/100m Max., Cable support Delay Skew: < 45 ns/100m, Operating Voltage: 72V , Impedance: 100 ± 15 Ω @100 MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance up to 700 MHz , RoHS Compliant. Make: Systimax, Legrand, Panduit.

SITC of Cat6 I/O with Dual Face plate: The Outlet shall meet or exceed requirement as per ANSI/TIA 568C.2,ISO/IEC 11801, & EN50173. The information outlet NEXT, PSNEXT, FEXT, ELFEXT, PSELFEXT and return loss should be verified for CAT6 @ 250Mhz & CAT6A @ 500Mhz. The information outlet connector shall be of gold/nickel, thickness of gold > 0.8 μm. The connectors shall be compatible as per IEEE 802.3af standard for POE application. The PVC material of Face plate should complie ABS /UL94-V-O certified. Make: Systimax, Legrand, Panduit

SITC of Cat6 I/O with Single Face plate: The Outlet shall meet or exceed requirement as per ANSI/TIA 568C.2,ISO/IEC 11801, & EN50173. The information outlet NEXT, PSNEXT, FEXT, ELFEXT, PSELFEXT and return loss should be verified for CAT6 @ 250Mhz & CAT6A @ 500Mhz. The information outlet connector shall be of gold/nickel, thickness of gold > 0.8 μm. The connectors shall be compatible as per IEEE 802.3af standard for POE application. The PVC material of Face plate should complie ABS /UL94-V-O certified. Make: Systimax, Legrand, Panduit

SITC of Cat 6, 24-port loaded, 1U Modular Jack Panel Should accommodate Cat6 with Rear Cable Management and Front removable Tooless Information outlet. Should have easy clip management with labels and clear label covers, Made with of Dicast Aluminium Alloy Material and Non Corrosive with Cat6 toolless RJ45 x 24 ports with color code front panel with patch cord locking. Make: Systimax, Legrand, Panduit

SITC of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. Make: Systimax, Legrand, Panduit(1 mtr length)

SITC of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. Make: Systimax, Legrand, Panduit(2 mtr length)

SITC of 6 core Single mode OS2 Unitube Armoured Optical fiber cable through existing conduit: The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. Outdoor Corrugated Steel tape Central loose tube. ( Standard Approved: ISO 11801 2nd edition/ EN 50173-1:2002 / IEC 60794-1/IEC 60793-2-50 class B1.3 / EN 60793-2-50: class B1.3 / ITU Recommendation G.652.D - the oder ITU designations A, B and C are also fulfilled / OS1/ISO/IEC 24702:2006, cat. OS2; also OS1 requirements are fulfilled/IEEE 802.3 - 2002 incl. 802.3ae ) Jacket. Make: Systimax, Legrand, Panduit

SITC of Rack mount Draw Type Loaded 6 port LIU available in Standard 19” ,Dimensions (mm) : 430 X 220 X 1U , Cold Rolled Steel as Raw Material , Consist of Top Cover and Bottom Panel , Easy to Assemble and Dissemble , Three Types of Input Holes Cable Entry Through Water Proof Cable Clamp , 12 Duplex SC or LC Adapter Interface , Splice 24 Fibers at Most with 1 Tray ,Adaptor, SM, Duplex SC, PC Type ,Pigtail, Support the TIA/EIA Telecommunication Wiring Standards. Compact Design , Telcordia GR-326-Core . Make: Systimax, Legrand, Panduit

SITC of OFC Patch Cor, SM (OS2), Duplex LC-SC, LC-LC PC Type, 3M, LSZH Fiber Optic Single Mode OS2 Patch Cords are offered in LSZH Jackets with Corning Fiber,Insertion Loss : <= 0.2 db, Max 0.3db/MTRJ: Max 0.5db Return Loss : PC>= 45db, UPC>=50db, APC>=60db. Make: Systimax, Legrand, Panduit

SITC of 1G-LX/LH SFP transceiver module,SMF, 1310nm, 9/125 um Single mode Fiber Type up to 20 KM. Make: Cisco, Digisol, Netgear

SITC of 24 Port Layer 2 PoE+ Switch having 24 x 10/100/1000 Mbps Ethernet PoE+ ports with 4 x 1/10Gig SFP+ ports ,1 x RJ45 port console port ,Switching Capacity 128 Gbps , Throughput 96 Mpps ,MAC Address 16k , Switch should support IEEE 802.3af (15.4W) & IEEE 802.3at (30W). Total PoE power: 370W or above , Switch should support DHCP server/relay/client, DHCP snooping/option82 , Switch should support Console, Telnet, SSH v1/2, HTTP, HTTPS, SNMP v1/v2/v3, RMON , TFTP, FTP, SFTP, NTP, ZTP, SPAN, RSPAN,Switch should support support ICMPv6, DHCPv6, ACLv6 ,IPV6 Telnet ,Temperature 0°C -50°C ,Power Supply AC: 100-240V. Make: Digisol, Cisco, HP

SITC of 9U/500D Wall Mount Rack with Accessories: The rack size should be 600W x 500D, Front frame integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 including Power Distribution Unit (06/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Lengt), 1 cooling Fan(230V AC - 90 CFM, dB 42), 2nos 1U Metal Cable manager with Plastic cable loops and H/W screw. Make:Valrack, Rittal, Legrand

SITC of 24U 600/650D UL Listed Floor mount Rack with Front perforated door with 3 point lock, Rear mesh door with Cam lock and 3inch Castor Wheel included with 2 no 6/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Length, 4nos 1U Metal Cable manager with Plastic cable loops, 2nos CFM FAN set, 1no Monitor Tray - Ventilation - 495W - 375D and H/W screw920sets). Make:Valrack, Rittal, Legrand

Supplying and fixing of following sizes of heavy class PVC FRLS conduit ISI marked along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required as per direction of Engg.-in-Charge .Make-AKG/BEC/Precision/Norpak

Supply and installation of Dual band 802.11ax WiFi6 Dual Band Access Point. Complying PoE+ for power, with inbuilt on premise virtual controller as well cloud based controlling and administration of WiFi systems All hardware should supplied with necessary mounting brackets and IN power cord with 3 years of comprehensive onsite warranty. Make: Cisco/Digisol/Netgear

AV SYSTEM

LCR Speakers: SITC of 3-Way Cinema Screen Speaker System with Tranducers LF: 3 inch or more with AES power rating of 1500W or more, HF: 12" or more with AES power rating of 60W or more, co-axial mid-high frequencr driver with 80° x 35° or better pattern control horn with AES power rating of 120W or more. Frequency Resposne of 50Hz to 20KHz or better. Sensitivity of 100dB @ 1W/1m or more. Maximum SPL for LF 130dB contineous @ 1m or more, for HF/MF 115dB contineous @1m or more. Make: Pulz/ L-Acoustic/Martin Audio/Bose/QSC

X-Over: SITC of Active Cinema 4 in 7 out speaker crossover system with balanced inputs and outputs; 24dB/octave filters or better, screen compensation and constant directivity compensation; sub sonic filters or better, one touch fall back emergency operation for centre channel failure, locking system for accidental change of parameters. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

Surround for Stall and Balcony: SITC of Cinema Surround Speaker with high power 12" or more full range driver. Frequency Response 70Hz to 18KHz or better. AES Power Rating of 220W or more. Sensitivity of 98dB @1W/1m or more. Contineous Maximum SPL of 121dB or more. Nominal Inpedance 8 ohm or better. Dispersion 85 degree or more. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

Cinema Processor: SITC of Cinema audio processor with touchscreen front panel interface for easy control. Easily integrates with multichannel Amplifier. Web user interface for remote configuration and control. Atmos designer compatibility for setup and precise system calibration. Internal crossovers to enhance audio quality. High resolution multi-rate EQ. Audio processing features: surround 7.1 and 5.1 playback, TrueHD Audio, supported sample rates of 44.1 KHz, 48KHz and 96 KHz at 16, 20 and 24 bit or better. Alternative content surround processing. Make: Dolby/QSC/ Marantz

AV Receiver: SITC of AVR system with 9.4 channels or more. Minimum 6 HDMI inputs plus eARC. 8k and Dolby Atmos. 110W per channel or more. Minimum number of powered channels 9. Amplifier Topology Class AB. Multichannel Surround Technologies DTS HD Master, DTS:X, DTS Neural:X, DTS Virtual:X, Dolby TrueHD, Dolby Atmos, Dolby Atmos Height virtualization, Dolby Atmos Music, Dolby Surround. Max number of processing (preamp) channels 11.4 or better. Should have Ethernet Ports, Wi-Fi, Bluetooth. Make: Marantz/Denon/Dolby/Yamaha

Amplifier: SITC of Four-Channel Class AB 2000W Amplifier. Frequency Response of 20Hz to 20KHz or better. SNR of 108dB or more. Slew rate > 10 V/us or better. Cooling Air flow from front to rear. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

Amplifier: SITC of Three-Channel Class AB 3500W Amplifier. Frequency Response of 20Hz to 20KHz or better. SNR of 108dB or more. Slew rate > 10 V/us or better. Cooling Air flow from front to rear. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

SITC OF 6 CHANNEL POWER AMPLIFIERS: each amplifier should deliver minimum power 200 watts per channel @ 8 ohms, 300 watts per channel @ 4 ohms. Frequency Response should be 30Hz to 20KHz +- 0.2 dB. Damping Factor greater than and equal to 100 and minimum signal to noise ratio of 95dB. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

LEFT & RIGHT LINE ARRAY CLUSTER: SITC of the cluster should provide a minimum horizontal disperssion angel 0f 100 degrees and a vertical angel of 70 degrees and be capabale of delivering a SPL of 105dB contineous Pink Noise at a distance of 65-ft with a minimum frequency response of 65Hz to 19KHz which is identical on both sides of the cluster. The cluster should be composed of minimum 8 nos of 8" Line Array Elements each having power handling of 250 watts AES, Sensitivity of 97dB @ 1 Watt 1 Meter or higher. The speakers should be course texture. The enclouser should be made up of European Brich Plywood. All metal parts should be powder coated or stainless steel. The complete unit should be black in colour. The rate is inclusive of chain, pulley ,flying stack system for Line Array spekaers, array frames/ Hanging/ Mounting arrangement for Suspension of upto 8 array modules offered above, Shall offer multiple rigging points for achieving desired pitch settings and other accessories for the speakers. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

SITC OF SUB-WOOFER: front of the stage subwoofer with minimum of 18” subwoofer drivers. With power handling capacity of 2000W (4000W peak). Frequency response of 35Hz to 200Hz or better. Sensitivity of 98dB @ 1W/1m. Continuous maximum SPL of 130dB. The rate is inclusive of brackets and other accessories as per the direction of Eng-in-charge. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

SITC of Inwall Sub-woofer for Side Wall at Back Side: four long throw 10” woofers in a column shaped. Power rating of minimum 1000W AES. Frquency Response of 40Hz to 400Hz or better. Sensitivity of 97dB @1W/1m. Continuous maximum SPL of 125dB.The rate is inclusive of brackets and other accessories as per the direction of Eng-in-charge. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

SITC OF STAGE MONITOR SPEAKERS: The speaker should be coaxial and provide a disperssion angel of 60 degress conical and be capable of delivering a SPL of 105dB contineous Pink Noise at a distance of 15ft with frequency response of 55 Hz to 20KHz. The speaker should be composed of minimum 12" driver each having power handling of 250 watts AES, Sensitivity of 98dB @ 1 Watt 1 Meter or higher. The speakers should be course texture. The enclouser should be made up of European Brich Plywood. All metal parts should be powder coated or stainless steel. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

FOH: SITC of 2-Way passive loudspeaker consists of 1" or more HF Driver and 12" or more LH Driver. Frequency Response of 70Hz to 20KHz or better. AES Power Rating of 400W or more. Sensitivity of 95db @1W/1m or more. Contineous Maximum SPL of 120dB or more. Nominal Impedance 8 ohm or better. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

SITC of MS upport Wall Mounting Accessory for above FOH speaker.

Operator Speaker: SITC of 2-Way passive loudspeaker consists of 1" or more HF Driver and 10" or more LH Driver. Frequency Response of 65Hz to 20KHz or better. AES Power Rating of 150W or more. Sensitivity of 95db @1W/1m or more. Contineous Maximum SPL of 115dB or more. Nominal Impedance 8 ohm or better. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

SITC OF Green Room SPEAKERS: The speaker should be coaxial and provide a disperssion angel of 90 degress conical and be capable of delivering a SPL of 112dB with frequency response of 70 Hz to 20KHz. The speaker should be composed of minimum 8" driver each having power handling of 120 watts AES, Sensitivity of 93dB @ 1 Watt 1 Meter or higher. Make: Pulz/ L-Acoustic/ Martin Audio/Bose/QSC

SITC of Transmitter for HDMI, RS 232, and IR Signal extension up-to 40m.Should support video signals HDR10+, Dolby Vision, Deep Color and 4096x2160 @60 4:4:4 resolution.Should support audio signals Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS-ES, DTS HD High Res, DTS-HD Master Audio & LPCM up to 8 channels.Should support HDCP 2.3 content protection. Should have 1x HDMI Input, 1x RJ45 output, 1x RS-232 & 1xIR. Should pass EDID and CEC. Should comply to CE, IC, FCC. Make: Crestron/Extron/AMX

SITC of Receiver for HDMI, RS 232, and IR Signal extension up-to 40m. Should support video signals HDR10+, Dolby Vision, Deep Color and 4096x2160 @60 4:4:4 resolution. Should support audio signals Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS-ES, DTS HD High Res, DTS-HD Master Audio & LPCM up to 8 channels. Should support HDCP 2.3 content protection. Should have 1x HDMI Output, 1x RJ45 input, 1x RS-232 & 1xIR. Should pass EDID and CEC. Should comply to CE, IC, FCC. Make: Crestron/Extron/AMX

Switcher: SITC of 8x8 matrix HDMI AV Switcher. Should have eight HDMI® inputs, eight HDMI outputs and 2x Balanced/unbalanced stereo line-level audio output. Should support video signals HDR10+, Dolby Vision, Deep Color and 4096x2160 @60 4:4:4 resolution. Should support audio signals Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS-ES, DTS HD High Res, DTS-HD Master Audio & LPCM up to 8 channels. Should support HDCP 2.3 content protection. Should have ethernet port supporting 1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, Web browser setup. Should support EDID management & third-party device control over CEC. Should support security features and protocols, Active Directory® credential management, 802.1X authentication, TLS, SSH, and HTTPS. Should have minimum1x USB port for firmware, configuration management and to power a USB powered device upto 5 V 500 mA power. Should be controllable over RS-232/ethernet Should comply to CE, IC, RoHS, FCC. Make: Crestron/Extron/AMX

SITC of digital directional antenna with Impedance:50 Ohm; Connector: BNC; Pick-up pattern: directional;Frequency range: 470 - 1075 MHz or better;Antenna gain: 5 dBi or better; Bidder Shall Submitted OEM Authorizationalong with technical bid Make: Sennheiser/Clock Audio/Rode

SITC of super-cardioid pre-polarized condenser instrument microphone with frequency response of 40 Hz- 20,000 Hz or better and sensitivity of 3 mV/P at 1 kHz or better , Maximum SPL of 139 dB at 1 kHz. Nominal impedance of 50 Ohm or better, with a min. terminating impedance of 1 kOhm or better. Make: Sennheiser/Clock Audio/Rode

SITC of pre-polarized condenser gooseneck microphone with overall length of 450mm or better, with XLR3M-type connector, shall offer radio frequency interference (RFI) shielding against intermodulation from wireless equipment or devices, cardioid microphone capsule with uniform 120° angle of acceptance (-3dB) or better, frequency response of 50 Hz to 20,000 Hz or better and sound input levels handling capability of minimum 130 dBspl or better, nominal equivalent noise level of 26 Dba or better and output shall be low impedance balanced (<100 ohms) with current consumption shall be 3 mA or better. Table stand with Microphone modes Toggle on / off, Push to mute, Push to talk, permanent on for connecting and operating XLR gooseneck microphones with XLR-3F microphone input and an XLR-3M microphone output operating on 48 V phantom power and current consumption of 3.7 mA or better. Make: Sennheiser/Clock Audio/Rode

SITC of dynamic cardioid vocal microphone with frequency response of 40 Hz – 16,000 Hz or better and the sensitivity of 2.7 mV/Pa at 1 kHz or better, nominal impedance of 350 Ohm or better, with a min. terminating impedance of 1 k Ohm. Make: Sennheiser/Clock Audio/Rode

SITC of cardiod pre-polarised condenser microphone with Frequency response of 20 - 20,000 Hz, Sensitivity of 7 mV/Pa;2.3 mV/Pa / 0.7 mV/Pa(with pre-attenuation) or better, Sound pressure level at 1 kHz of 137/147/157 dB SPL(depending on pre-attenuation)Nominal impedance 100 ohm Min. terminating impedance 1 k ohm or better Make: Sennheiser/Clock Audio/Rode

SITC of microphone set consisting of steel drum case; 1 nos dynamic cardioid microphone with an integral stand mount, fitted with a hum compensating coil for low frequency instruments with frequency response of 20 Hz – 16,000 Hz or better and the sensitivity (free field, no load) of 0.25 mV/Pa at 1 kHz or better and 0.9 mV/Pa at 50 Hz or better, nominal impedance of 350 Ω or better, with a min. terminating impedance of 1 kΩ; 4 nos dynamic cardioid instrument microphone for drums and percussion as well as brass and woodwind instruments featuring an integral stand mount and hum compensating coil with frequency response of 40 Hz – 18,000 Hz or better and the sensitivity (free field, no load) of 1.8 mV/ Pa at 1 kHz or better. nominal impedance of 350 Ω or better, with a min. terminating impedance of 1 kΩ or better; 2 nos super-cardioid pre-polarized condenser instrument microphone with frequency response of 40 Hz- 20,000 Hz or better and sensitivity of 3 mV/P at 1 kHz or better, Maximum SPL of 139 dB at 1 kHz or better. Nominal impedance of 50 Ohm or better, with a min. terminating impedance of 1 kOhm or better. Make: Sennheiser/Clock Audio/Rode

SITC of 48 Input Channels Digital Mixer with 32 Local Mic Inputs (XLR), 2 ¼” Stereo Inputs (TRS), 1 3.5mm Stereo Input, 36 Total Busses, 12 Stereo Mix (Aux or Group) + Main, AES Digital Output, I/O Port for Option Card (including 3rd party protocols –Dante/Waves), 7" colour touchscreen, 32+1 Faders with 6 Layers for 192 assignable Channel Strips, 32 Backlit LCD Channel Strip displays, SQ-Drive for stereo and multitrack recording/playback direct to USB drive, USB transfer of Scenes, Libraries, Shows, 32x32 channel USB streaming to/from Mac/PC. Make: Yamaha/ Allen & Health/ Behringer

SITC of Snake Cable: Supply and Laying of 8 pair Analog Audio Snake Cable, 24. AWG stranded (7x32) TC conductor, Polyolefin insulation, individually shielded, number or color-coded PVC jackets and shields bonded to strip simultaneously over all shield and 24 AWG TC drain wire. Make: Krystals/ Kramer/ Belden

SITC of Speaker Cable: Supplying and Laying of 2.5 Sq.mm 2 core speaker cable. Make: Krystals/ Kramer/ Belden

SITC of Speaker Cable: Supplying and Laying of 4.0 Sq.mm 2 core speaker cable Make: Krystals/ Kramer/ Belden

SITC of Speaker Cable: Supplying and Laying of 6.0 Sq.mm 2 core speaker cable Make: Krystals/ Kramer/ Belden

SITC of Microphone Cable: Supplying and Laying of of 20 AWG 2 core microphone cable Make: Krystals/ Kramer/ Belden

Supplying and Laying of UTP 4 pair 23 AWG Cat 6A LSZH Cable in the existing surface/recessed steel/PVC conduit as required conforming to the following standards likeANSI TIA/TIA 568.2-D, ISO/IEC 11801. CABLE dia 7.6 mm with bending radius-4x cable diameter, pulling force is 11.5kg, operates at frequencyof 500Mhz with necessary acessories as per the direction of Engineer-in-charge.Make-Systimax/Legrand/Panduit.

SITC of Connectors: SITC of required adequate AV connectors: XLR male, XLR female, RJ45, 3.5mm Stereo Connector, 6.35 mm mono connector, BNC. Make: Neutrik/ MX/ Krystals/ Belden/ Legrand

SITC of Stage Box: SITC of 8 XLR stage box. Make: Custom

SITC of Digital Podium with Built-in highly sensitive Interactive Panel with adjustable Motorized tilt. Display Size 21 inch or higher. Resolution 1920 x 1080 Full HD or better. Brightness 350 cd/m² (typ) or higher. Connectivity (Minimum) USB x 1, HDMIx 1, DVI x 1, VGA x 1 or better. Battry Free EM Pen. Processor: Intel Core i5 (10th Gen or better processor), RAM 8 GB, Storage 500 GB SSD or better. Controller: Ports on front Panel of Controller (Minimum): VGA,HDMI,USB3.0x2,Audio IN or more. Full HD Visualizer: Camera Sensor 1/4"CMOS Sensor F=2.8, Effective Pixels Min. 8 Mega Pixel or better, Frame Rate Min. 30fps or better, Two Type LED system Top LED & Side LED strip. Make: Globus/Infonics/AHA/UNIE Podium Delta plus(Peoplelink)

SITC of 20K Lumens LCD Projector, Resolution 1920 x 1200 pixels, Light source Laser diode. Contrast Ratio 3,000,000:1. HDMI 19-pin x 2 (Compatible with HDCP 2.3, Deep Color, 4K/60p signal input6), CEC supported. RJ-45. Power Supply AC 100–240 V, 50/60 Hz. The cost is inclusive of mounting arrangement for the projector. Make: Panasonic/Barco/Chirstie

SITC of 42U 800/1000D UL Listed Floor mount Rack with Front perforated door with 3 point lock, Rear mesh door with Cam lock and 3inch Castor Wheel included with 2 no 6/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Length, 4nos 1U Metal Cable manager with Plastic cable loops, 2nos CFM FAN set, 1no Monitor Tray - Ventilation - 495W - 375D and H/W screw920sets). Make:Valrack, Rittal, Legrand

FIRE FIGHTING WORKS

Supplying, installation, testing and commissioning of Electric Motor Driven Pressurization Terrace Pump having discharge of 900 LPM at 35 Mtr head complete with Pump Set, Electric Motor suitable for operation on 415 V ,3 ph, 50 c/s AC supply , Base Frame.Make-Wilo/KSB/Kirloskar/Grundfoss

Supply & Laying ofAl armoured XLPE power cable of 1.1 KV grade of following size on Cable

3C X 16 sqmm xlpe Armoued cable

Cable laying Laying & fixing of one no. PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on Cable Tray as required.

Upto 35 Sqmm

End Termination

3C X 16 sqmm

PIPE & VALVES ETC.

Supply,Installation,Testing & Commissioning of 'C' Class heavy duty MS pipe (as per IS 1239 upto 150 mm NB and IS 3589 for above 150 mm 6mm thick) with flanges and fitting such as bends, tees, reducers, rubber insertions and galvanized nuts and bolts of following size on surface along wall / shaft with MS bracket, suspended from ceiling/ beam with suspenders duly painted with two coats of primer and finished with enamel paint of approved colour laid through pipe or in trench after wrapping with hassen cloth after applying coal tar primer as required as per direction of Engineer-in- charge.MAKE:JINDAL/TATA/SAIL

Providing, fixing, testing and commissioning of following size manually operated hand lever type cast iron double flanged slim seal wafer type Butterfly valves with EPDM iron disc as per IS-13095 having pressure ratting PN -1.60 including fixing the same with supply of required jointing materials like rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure etc. all complete as per specification & direction of E.I.C.Make-Zoloto/AUDCO/Leader

Providing, fitting & fixing of following size cast iron double flanged type dual plate Non return Valve as per IS- 5312 (Part 1): 2004 with ISI mark of pressure ratting PN-1.60 including fixing the same with supply of required jointing materials like flanges, rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure etc. all complete as per specification & direction of Engineer-in-charge. Make-Zoloto/AUDCO/Leader

Supply,Installation,Testing & Commissioning of orifice plate made of 6mm thick stainless steel with orifice of required size in between flane and landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 Kg/ sq cm complete as required.

Supply,Installation,Testing & Commissioning of Pressure gauge of 0-16 Kgf/sq.cm. range with cut-off bronze ball valves of suitable size with all accessories as per direction of Engineer-in-charge.MAKE: H.GURU/G.GURU

Supply,Installation,Testing & Commissioning of Pressure Switch with cut-off bronze ball valves with integral strainer & flare nut (mixed ends) of suitable size with all accessories as per direction of Engineer-in-charge.MAKE: DANFOSS/INDFOSS make

Supply,Installation,Testing & Commissioning of 100 MM stainless steel strainer fabricated out of 1.6 mm thick stainless steel sheet Y Stainer with 3 mm dia hloes with stainless steel flange as required. Make-Zoloto/AUDCO/Leader

Supply,Installation,Testing & Commissioning of Air vessel made of 250mm dia, 8mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia Gun metal wheel valve, with required accessories, pressure gauge and painting with synthetic enamel paint as required.

WET RISER CUM RING SYSTEM

Supply,Installation,Testing & Commissioning of Stainless steel Hydrant Valve / Landing valve, of 63 mm NB size, type-A, single headed , oblique type, as per IS :5290/93 and as per direction of Engineer-in-charge.Make-Minimax/Newage/Fireshield/Safex

Supply,Installation,Testing & Commissioning of SS short branch pipe with 63 mm male inlet and 19 mm outlet nozzle, as per IS:903 and as per direction of Engineer-in-charge.Make-Minimax/Newage/Fireshield/Safex

Supply,Installation,Testing & Commissioning of 63 mm NB and 15meter long RRL Fire Hose fitted with 63mm intstantaneous stainless steel male & female SS coupling, complete by GI wire binding for Internal Hydrant as per direction of Engineer-in-charge.Make-Minimax/Newage/Fireshield/Safex

Providing supply & fixing of MS Hose Box for of suitable size(750X600X250mm) to accomodate 2 nos. of 15/ 1 no of 30 mtr long fire hose and a branch pipe, wall mounted type as per direction of Engineer-in-charge.Make-Minimax/Newage/Fireshield/Safex

Supply,Installation,Testing & Commissioning of Swinging pattern wall fixing first aid hose reel made from MS sheet and waterways and moving parts with rubber hose of 20 mm dia. and 30 mtrs. long with ABS(Plastic) shut-off nozzle as per IS: 444/IS: 12585 Type-I., complete with all accessories as per direction of Engineer-in-charge.Make-Minimax/Newage/Fireshield/Safex

Providing, fitting and fixing of C.I. 25 MM single air relief valve with stop cock confirming to IS:14845/2000 with ISI mark for water works purpose including fixing the same with hydrant riser including testing & commissioning the system etc. all complete as per approved specification & direction of Engineer-in-charge.

Providing, fitting & fixing of 4-Way GM fire brigade connection consisting of 63 mm dia instantaneous type male couplings with built-in check valves, 150mm dia flanged outlet complete with bolts, nuts and rubber insertions confirming to IS:904 with ISI mark including testing & commissioning the system etc. all complete as per apporoved specification & direction of EIC. Make-Zoloto/Audco/Leader

EXTINGUISHER SYSTEM

Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S cylindrical body, squeeze lever dischange valve fitted with pressure indicating gauge internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS : 2878 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.Make- Safex/ Fireshield/Kanex/ Ceasefire .4.5 kg capacity

Providing and fixing ABC type fire extinguishers consisting of welded M.S cylindrical body, squeeze lever dischange valve fitted with pressure indicating gauge internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.Make- Safex/ Fireshield/Kanex/ Ceasefire.6 kg capacity

Supplying and installing at approved location approved make fire buckets at 24 gauge galvanized stseel sheet, standard 9 liters capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letter "FIRE" in black and gold. Cost shall be inclusive of Providing MS stand duly painted over a coat of primer (one stand shall be suitable for hanging 5 buckets.

AUTOMATIC FIRE DETECTION & ALARM SYSTEM

Supplying, installing, testing and commissioning of photo electric adressable multi sense smoke detector with inbuilt isolator module/isolator base ,base, junction box and other accessories. Make-Morley IAS/ Siemens/ Bosch/ Edward/ NOTIFIER /GST/ Schneider

SITC of Response Indicator..Make-Morley IAS/Siemens/Bosch/Edward/NOTIFIER/GST/Schneider

Supplying, installation, testing and commissioning of Intelligent Reflective Beam Detector with 4 pieces Reflectors, Capable used as Conventional detector, Fire and Fault signal relays available, 24VDC required, Detection Range 8-100 Meters (Certified by LPCB): GREEN / AMBER / RED Make-Morley IAS/Siemens/Bosch/Edward/NOTIFIER/GST/Schneider

Supply, Installation,Testing & Commisioning of 2 loop Microprocessor based Addresable fire alarm control panel , fully networkable with each loop capable of taking 99 devices, 8 line x 40 character alpha- numeric liquid crystal display .The panel shall be soft addressable type . The panel shall be able to give pin point location of all fire/fault conditions. Further, the panel must be able to automatically switch off respective control switches when ever any alarm is triggered. The panel shall have integral SMF lead acid batteries with sealed cells of 24 V capable of running for a minimum of 8 hours with integral battery charger complete as required and as per specification. The fire alarm panel shall be suitable for software integration with BMS & PA system. Make-Morley IAS/Siemens/Bosch/Edward/NOTIFIER/GST/Schneider

Supplying, installation, testing & commissioning of Addressable Single Output Module,Single Output Module, provides dry contact (Loop powered) or active output (24VDC required, cable monitored) (Certified by LPCB)) indicates system status: GREEN / AMBER / RED.Make-Morley IAS/Siemens/Bosch/Edward/NOTIFIER/GST/Schneider

Supplying, installing, testing and commissioning of Addressable Manual Call Point with back box.Make-Morley IAS/Siemens/Bosch/Edward/NOTIFIER/GST/Schneider

Supplying, installing, testing and commissioning of Analogue Addressable Loop powered Sounder with strobe light.MakeMorley IAS/Siemens/Bosch/Edward/NOTIFIER/GST/Schneider

Supplying, installing, testing and commissioning of 2C x 1.5 mm², armoured, single stand, outer sheathed, FRLS, PVC insulated copper conductor cable confirming to specified IS standards .Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI

SIGNAGES:-Providing and installing in position the following type of sign boards made out of 3mm thick flexyle photoluminescent based glow in dark sheeting with luminous properties enclosed in a weather proof Uvstabilized film with UV screen printing by imported links pasted over3 mm thick cast acrylic from front side with 6 mm thick acrylic, -20 to+80 deg C, Suitablefor indoor use, greenish yellow, glow visible upto 4-6 hr in total darkness.Make-Prolite/Bajaj

PANEL SUPPRESSION SYSTEM

Supply , Installattion,Testing and Comissioning of 5LB Clean Agent System Complete with all Necessary Clean Agent FK-5-1512 /novec 1230 (UL listed )gas with PESO approved cvlinder fitting support and accessories,connected with CE,PI Mark & PESO approved DLP valve,End of line Adaptor and pressure switch Cylinder will be Helium Leak Tested to 10-7 mbar I/S for leakage proof Make:SUPREMEX/FIREBOY/AMEREX

Supply & Laying of Linear pneumatic heat Detection Tube with all necessary fittings & supports. (Make: SUPREMEX / FIREBOY / AMREX)

Supply, installation, testing and commissioning of Health Monitoring Panel with Audio Visual Alarm. The Panel Should have Provision for integration with Fire Alarm/ SCADA/ BMS System. (Make: SUPREMEX / FIREBOY / AMREX).

STAGE LIGHT

SITC of 150W High Quality LED Parcan Light complete with, Lamp source 3200K CCT Colour temperature, CRI & TLCI Values above 95, COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided), DmX 512 dimming with 3 channel control, Beam Angle of 11˚ / 25˚ / 35˚, Total Power Consumption of 160W, High quality output replacing 1000W Halogen Par, Flicker Free 100% for Tv & Film Cameras 11.7KHz Refresh Rate, Linear Dimming 0 ~ 100%, Fuse and Internal safety protections, Strobe option Adjustable 1~25 times/Sec Variable, Fixture provided with Yoke of Manual Adjustment, 5 Pin XLR for DmX , Black powder coated body. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014, LM79 Certificates from NABL Accredited laboratory. Brand embossed impact on the light body for genuine product. Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of 300W LED Profile Spot 19 Degree Light complete with, 3200K CCT Colour Temperature COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) , CRI & TLCI above 95, Strobe option Adjustable 1 ~ 25 times / Sec 4 Kinds of dimming curves, Black finish housing, Manual Focus with 4 Beam shaping cutters, Efficient and well-designed Lamp reflector, Efficient Copper tube based Heat Sink for Heat Dissipation, Sleek and Unique Designed Light weight body, Fixture provided with Yoke of Manual Adjustment DmX 512 dimming with 1 or 3 Channel modes IP20 protection having Lux @ 3 Mtr above 11412 suitable to illuminate the key presenter or talent on stage. illuminate the key presenter or talent on stage. RDM Control options with latest technology (RDM ID to be specified), LM79 Certificates from NABL Accredited laboratory, Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014. Brand embossed impact on the light body for genuine product. Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of 400W LED Blinder Light 30 Degree complete with 3200K CCT 4x100W Chip On Board LED Lamp source COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided), DmX 512 dimming with 8 Channel modes CRI & TLCI Value > 95, Strobe option Adjustable 1 ~ 25 times / Sec VariableBeam Angle 30 Degree, Total Power Consumption of 410W, 11.7KHz Refresh Rate, In built preset’s for effects, Fuse and Internal safety protections, Active Cooling with Low Noise Fan 5 Pin XLR for DmX, High quality well designed inbuilt reflector, Flicker Free 100% for Tv & Film Cameras, Black finish housing, IP20 protection, Having Strobe option and smooth dimming illuminate Stage with uniform light intensity levels. RDM Control options with latest technology (RDM ID to be specified), LM79 Certificates from NABL Accredited laboratory. Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012. CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of 54 x 3W LED Par Light RGBW, Beam Angle 25° complete with LED source from Lumi led / Seoul / Nichia or reputed make (LM80 to be provided) , RGBW 3W Lamp source x 54 Pcs, DmX 512 dimming with 8 Channel, High Bright Red, Green, Blue, White LED’s Source, Unlimited Colour, Mixing through DmX, 0 ~ 100% Linear dimming, In built presets for different colours, Strobe Mode 20 times/Sec, Data DmX through 5 Pin XLR’s, 65dB ~ 130dB Sound sensing capacity, Having Sound Control & Master Slave Auto Run Mode, Illuminate the Indoor stage with unlimited colour effects, Rigidly built pressure die-casted Aluminium body. RDM Control options with latest technology (RDM ID to be specified), Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012. CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014. LM79 Certificates from NABL Accredited laboratory. Brand embossed impact on the light body for genuine product Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of 54x3W LED 3200K Par Light Beam Angle 25° complete with 3200K 3W Lamp source x 54 Pcs, LED source from Lumi led / Seoul / Nichia or reputed make (LM80 to be provided), Having CRI TLCI Values above 95, Flicker Free for high FPS , Smooth fade in and Fade out, High precision steady colour, No heat, DmX 512 dimming with 2 Channel, 0 ~ 100%, Powder coated Black finish housing, Rigidly built pressure die-casted Aluminium body, LED Easy view display Data DmX through 3 / 5 Pin XLR’s, 65dB ~ 130dB Sound sensing capacity, Power In and Out Connections, Total Power Consumption of 180W, Sound Active Mode Control IP20 protection. RDM Control options with latest technology (RDM ID to be specified), LM79 Certificates from NABL Accredited laboratory, Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012, CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014, Brand embossed impact on the light body for genuine product Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of 200W LED Fresnel Light having, COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided), 3200K colour temperature High quality uniquely designed Fresnel Lens, CRI,TLCI and R9 value above 95, LED COB Based Source, No Multiple Shadows – Single Source illumination, Total Power Consumption of 210W, Linear dimming 0 ~ 100% Adjustment, Flicker Free for High FPS, Power AC100-240V, 50Hz, Working Temperature - +40° ~ -30°, Active Cooling with Low Noise Fan, DmX & RDM Control options with latest technology Fixture provided with Yoke of Manual Adjustment, Manual and DMX control Option mode through 5pin/3pin xlr, Black powder coated fabricated housing with normal yoke. RDM Control options with latest technology (RDM ID to be specified) LM79 Certificates from NABL Accredited laboratory Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012, CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014, Brand embossed impact on the light body for genuine product, Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of 175W LED Projector Spot Light complete with CCT Tuneable Lamp source LED source from Lumi led / Seoul / Nichia or reputed make (LM80 to be provided) Having CRI TLCI Values above 95 High precision steady colour No heat, DmX 512 dimming with 6 Channel Beam Angle 15°/ 25° / 45° 0 ~ 100% Smooth dimming, Powder coated Black finish housing Rigidly built pressure die-casted Aluminium body LED Easy view display Flicker Free for high FPS Smooth fade in and Fade out Data DmX through 5 Pin XLR’s Total Power Consumption of 175W Sound Active Mode Control IP20 protection. 65dB ~ 130dB Sound sensing capacity Power In and Out Connections RDM Control options with latest technology (RDM ID to be specified) LM79 Certificates from NABL Accredited laboratory, Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012, CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014, Brand embossed impact on the light body for genuine product Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Moving Head Beam effect light 12R Base, High bright long throw beam with linear zoom range, Zoom range from o to 3.8 Degree, Lamp Source: Yodn 280W 12R Arc Lamp , Total Power Consumption of 450W, Electrical: AC 100-240V, 50/60Hz 16 Channel DmX Control, Color System:1 color wheel+14pcs, Prism：8prism+48prism with rotation effect, 16 Bit Dimmer Control, Gobos System: 16+1pcs gobos, Double chip Stroboscopic (0.5 ~ 9 times /SEC), Pan Angle 540°, Tilt Angle 270° IP20 rated product. Electrical: AC 100-240V, 50/60Hz Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Aluminium O Type clamp made up of high grade aluminium having thickness not less than 5mm suitable for round tubes of dimension varying from 40 to 55mm outer diameter, provided with fixture mounting 25mm M8 bolt and wing nut, minimum 100KGs of safe working load, 40mm bolt and wing nut for pipe locking. Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Light Fixture dual safety Chain made up of GI wire rope Bundled and twisted together Having load bearing capacity above 200 Kgs Sleeve on the rope. Carabiner Clip Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS Base plate Threaded rod, Black powder coated finish All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems. Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Fixed stage Lighting bar/winch of 15Mtr length constructed with an dual construction light bar with an Mild Steel 40NB 48 OD black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar. It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS angle which is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fasteners of 10mm which can take an total load of 400KG each fastener. Made out of 48mm Outer Dai, 40 Nominal Bore Material for the light bar shall be of Mild Steel Pipe. Dual Barrel Arrangement Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Dual Construction and an additional End Caps on the Pipe end shall be there Light bar Length shall be of customized type as per site condition. Upper pipe of dual construction is used to anchor the bar lower pipe is effectively used to hang the light fixtures Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Fixed stage side Ladder as per the design, Size of 600mm x 3000mm, Manual movable Made out of 40NB 48 OD Mild steel pipe dual barrel Dual Barrel Arrangement Dual Construction Powder coated with Matt black Texture Single Construction with Cross connecting pipes Cross connecting Pipes at every 600mm Ladder can be moved along the track or adjusted as required, Spud & Trolley, Pivoted or Fixed Suspenders as per site conditions Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Fixed FOH Lighting bar/winch of 16Mtr length constructed with an dual construction light bar with an Mild Steel 40NB 48 OD black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar. It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS angle which is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fasteners of 10mm which can take an total load of 400KG each fastener. Made out of 48mm Outer Dai, 40 Nominal Bore Material for the light bar shall be of Mild Steel Pipe. Dual Barrel Arrangement Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Dual Construction and an additional End Caps on the Pipe end shall be there Light bar Length shall be of customized type as per site condition. Upper pipe of dual construction is used to anchor the bar lower pipe is effectively used to hang the light fixtures Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of2mm thick CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt texture finish Power Distribution Electrical panel having a Incomer of 100A.4P MCCB,16kA adjustable thermal and fixed magnetic type with Ics=100%Icu. Floor mount / rack mount / wall mount. Miniature circuit brakers of 36 nos. single poles shall be fixed of different ratings from 6/10/16/25A as per the lighting fixtures. Wiring inside the module for power, control protection and instrument etc. shall be done with use of 1100 V confirming to IS 694 and IS 8130 All welding slag grounded off and welding pits wiped smooth with plumber metal. Power panels shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component does not attain temperature more than 40 degree Celsius. Fabricated panel shall be supported with ms angles of size 25mm x 25mm with an 1.8mm thickness sheet to hold the structure. Neutral separation made, Voltmeter, Ammeter display for reading visualization Individual MCB control for 36 outgoing circuits RYB Phase indicators internally wired using IS certified wires and cables.Terminal for both incoming and outgoing cable shall be suitable for 1100 volts grade, aluminium/copper conductor PVC insulated and sheathed, armoured cable and shall be suitable for connections. Provided with ivory connectors for the internal terminations and external outgoing connecting points Custom built as per specification and project requirement.Make of mccb:Legrand Dpx3/ABB Formula/Schneider CVS/Siemens 3VA/ABB Formula Make of MCB: Legrand Dx3/ABB sb200/Schneider Acti 9/Siemens Betaguard /ABB SB200

SITC of High quality power junction box 4 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ) Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating Temp Mouldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall / floor fixing. Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of High quality power junction box 2 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ) Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating Temp Mouldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of High quality Dimming In junction box 1 way made up of MS Sheet metal fabricated housing, High temperature resistant insulator material. All metal housing offers best overall RF protection & electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Male socket. Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of High quality Dimming Out junction box 1 way made up of MS Sheet metal fabricated housing High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding, Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Female socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of DmX Loop Junction Box having 1 No. of DmX 5 Pin XLR, Female Socket & 1 No. DmX XLR Male Socket fitted on to a sheet metal fabricated compact Junction box powder coated with matt black texture finish paint. High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding. Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Internal earthing copper bare conductor of size 14 SWG for power network related to work coming under our scope and Installation hardware’s such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work. Make: Leksa Lighting /Canara Lighting/ETC/ADJ

SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x150 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dissipation provided with lid. Make: Leksa Lighting /Canara Lighting/ETC/ADJ

SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 75 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dissipation provided with lid. Make: Leksa Lighting /Canara Lighting/ETC/ADJ

SITC of DmX Male Female Connectors 5 Pin having rubber sheath protection for Cross connecting DmX wiring connections Make: Leksa Lighting /Canara Lighting/ETC/ADJ

SITC of DmX Male Termination Connector 5 Pin soldered with required capacity of resistor for signal defaming Make: Leksa Lighting /Canara Lighting/ETC/ADJ

SITC DmX Touch Screen based controller having 7” Multi touch screen option 2 DmX Outlets 5 Pin XLR’s, 512 Channels each, Optically isolated outputs, 4 Smooth Encoders for control operation of attributes, Backlit keys, 12 Fader Stacks, 600+ Playbacks, 350+ Group saving, 350+ Presets, User defined shape effects, Macro saving options, External Midi timecode options, Internal clock, Shortcut user interfaces, Master fader, Blackout Key under Master fader, Numerical keypad for the light command entry inbuilt embedded within controller, USB interface, Scene saving options, Show saves and load save features, custom built user interface library for fixture files. Make: Leksa Lighting /Canara Lighting/ETC/ADJ

SITC of FRLS Copper unarmoured Flexible cable IS694 having 3 Core each of 1.5 Sq mm size.

SITC of 5 Core DmX Cable with Sheathed housing on the cable, well designed insulation, low noise suitable to transmit DmX signal.

STAGE DRAPERY

SITC of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS Base plate Threaded rod, Black powder coated finish All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems.Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of C Profile MS Hot rolled strips 3mm thick with Extra U bend used either to create basic supports Customized 40 x 50mmm, All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Makes easier to suspend all the stage machinery Duly powder coated Matt black texture finish paint Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Cable Connecting Circuit Boxes for the termination of cables from Electrical panel to the grid level point made out of MS Sheet metal fabricated housing duly powder coated with matt black texture finish paint, fitted with required channels and ivory connectors, necessary glands etc. Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of FRLS Copper unarmoured Flexible cable IS694 having 7 Core each of 1.5 Sq mm size.Make-Polycab/KEI/Finolex/RR Kabel/Gloster/Havells

SITC of FRLS Copper unarmoured Flexible cable IS694 having 4 Core each of 4 Sq mm size. Make-Polycab/KEI/Finolex/RR Kabel/Gloster/Havells

SITC of High quality Velvet fabric fire retardant treated as per approved colour and make with a gathering of 100% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Main Curtain) Size: 21Mtr x 6 Mtr. Make-Response Nexgen/Pro-acoustics

SITC of Glazed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 50% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Rear Curtain) Size: 20Mtr x 6Mtr. Make-Response Nexgen/Pro-acoustics

SITC of Glazed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 50% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Frills) Size: 16Mtr x 1.2Mtr. Make-Response Nexgen/Pro-acoustics

SITC of High quality Velvet fabric fire retardant treated as per approved colour and make with a gathering of 100% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Main Valance) Size: 20Mtr x 1.5Mtr. Make-Response Nexgen/Pro-acoustics

SITC of Glazed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 0% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing. (For Wing) 6Mtr x 1.5Mtr Make-Response Nexgen/Pro-acoustics

SITC of On Stage Fixed Frill Bar 16Mtrs Length Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, supported to hang the frill, connected with MS Flat duly powder coated with matt black texture finish paint. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of On Stage Fixed Valance Bar 20 Mtr Length Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, supported to hang the Main Valance of the stage system duly powder coated with matt black texture finish paint. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Fixed Wing Structure designed as per site condition for a height approx 6Mtr x 1.5Mtr made up of MS Square tube of 25mm or higher size rested on pivotable trolley on a track for the rotation of the wing. Adjustable floor locking screw jacks with rubber grips. Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp and 360° Rotatable. Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Motorized DMX operated Main Curtain 21 Mtrs straight, Centre parting as per design. This mechanism shall be provided with 01 Nos. of 1 HP /1.5HP, 1440 RPM, 90 B5 frame, 3Ph. 415VAC Motor with Brake for Motor System to lift a load which should be synchronized with Motor Control centre Panel. Winch shall have 3 phase motor with an RPM of 1440, KW (HP): 0.74(1)/1.1(1.5), Frame: 90S, EFF:75.0%, MTG : B5, AMP :2.7Y, Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG:62052Z, IP:55, AMB:50 degree. The outer surface temperature is limited. It shall have a Worm Reduction Gearbox with GMRV-90 80:1, 90B5, Single Reduction 7.5:1 to 100:1 and the size shall be 90. It shall have a drive unit base frame to fix the gear box which contains one shaft Made up of I Track for complete length Curtain holding trollies with ball bearings for smoother noiseless movement consisting of 4-wheeler master trolley and 2-wheeler trolley placed uniformly at specific interval of200mm /250 mm throughout the track Overlap of 0.5~0.9 Mtrs. Motor Cable termination box Trollies are uniformly distributed along the track at every 200/250mm with a master trolley. Open and close limit controller. Drive unit with suitable capacity of motor unit, Wire Rope shall be of GI Wire ropes Min 3mm Dai Undergone through various chemical treatment to keep them rust free, Black texture finish paint. All metal parts are powder coated Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Motorized DMX operated Rear Curtain 20 Mtrs straight, Centre parting as per design. This mechanism shall be provided with 01 Nos. of 1 HP /1.5HP, 1440 RPM, 90 B5 frame, 3Ph. 415VAC Motor with Brake for Motor System to lift a load which should be synchronized with Motor Control centre Panel. Winch shall have 3 phase motor with an RPM of 1440, KW (HP): 0.74(1)/1.1(1.5), Frame: 90S, EFF:75.0%, MTG : B5, AMP :2.7Y, Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG:62052Z, IP:55, AMB:50 degree. The outer surface temperature is limited. It shall have a Worm Reduction Gearbox with GMRV-90 80:1, 90B5, Single Reduction 7.5:1 to 100:1 and the size shall be 90. It shall have a drive unit base frame to fix the gear box which contains one shaft Made up of I Track for complete length Curtain holding trollies with ball bearings for smoother noiseless movement consisting of 4-wheeler master trolley and 2-wheeler trolley placed uniformly at specific interval of200mm /250 mm throughout the track Overlap of 0.5~0.9 Mtrs. Motor Cable termination box Trollies are uniformly distributed along the track at every 200/250mm with a master trolley. Open and close limit controller. Drive unit with suitable capacity of motor unit, Wire Rope shall be of GI Wire ropes Min 3mm Dai Undergone through various chemical treatment to keep them rust free, Black texture finish paint. All metal parts are powder coated Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Fixed Cyclorama arrangement of 13 Mtrs straight as per design made up of I Track for complete length with Trollies uniformly distributed along the track at every 200/250mm. All metal parts are powder coated with black texture finish paint. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Make- Leksa Lighting/Canara Lighting/ETC/ADJ

SITC of Perforated plastic cyclorama screen with perforation on 1side with gathering of 0% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies. Size:13Mtr x 6Mtr Make- Leksa Lighting/Canara Lighting/ETC/ADJ

D.G. SET(320 KVA DG SET)

Supply, Transportation, erection, testing and commissioning of 3 Phase, 415V, 50Hz, water cooled multi cylinder diesel generator set with alternator of 320KVA ( Make -Kirloskar / Jakson/Mahindra) out put contineous rating directly coupled Engine and Alternator with guard and mounted on a common base plate of Robust construction and complete with AMF panel having IP-52 protection, Acoustic Enclosure as per CPCB IV+ norms , sound absorbing material, to restrict sound level up to 75 dB up to 1 mtr distance and as per CPCB IV+ norms etc as per following specifications mentioned below. Warrentee period must be 2 years. ALTERNATOR:The alternator of the output rating shall be 3 Phase, 415V, 50Hz, Ac , 0.8 P.F. lagging at 1500 RPM. The alternator is self excited, self regulated, and shall confirm to IS: 13364 of 1992 with regulation of +5% from no load to full load. degree of protections shall be IP21. ENGINE: Diesel Engine start, developing suitable BHP output at 1500 RPM with mechanical / electronic governing so as to enable the alternator to give 320KVA continuous output at 0.8 P.F. lagging at NTP conditions. The diesel engine shall be capable of providing 10% O/L for 1 Hr for every 11 Hrs of continuous running at full load. The engine with 1st filling of oil and Diesel etc. 01. Exhaust pipe of required size and length with insulation or clading. 02. Diesel tank suitable for 8 to 10 Hours running capacity. 03. Residential Silencer. 04. SMF Batteries with leads as per the Manufacturer standards.

AMF PANEL: Cubical, Compartmentalized, AMF Panel Baord with all Power & Control Contractors, Switches, Meters and other accessories, Internal Wiring, connection, inter-connection etc. for Trouble Free smooth function for 320KVA DG Set complete with Battery Charger & leads as required. BASE PLATE: Common Base Plate of required size for mounting of Engine Alternator Set fabricated from MS Channerl and vibration damping arrangement with cushy foor mounting including paintng etc. as required. FOUNDATION: Suitable size Cement Concrete (1:2:4) foundation duly plastered and finished with neat coat Cement as required along with smoke exhaust system piping including base frame of structure & lightening protection system. , control cable of 15mtr 2.5sqmm 6core , civil foundation work. (The Manufacturing of DG set shall not in any case be more than six months old from the date of award of work)

P.H. WORK Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor pvc pipes confirming to ASTM-D- 1785/89 (Sch-80) and pipe fittings of the following nominal borewith clamps including making good the wall, ceiling and floor, testing all complete as per specification and direction of the Engineer-in-charge.

Ground floor

25 mm CPVC(sdr-13.5) pipes (Oriplast/Supreme)

32 mm CPVC sdr-13.5 pipes (Oriplast/Supreme)

First floor

25 mm CPVC(sdr-13.5) pipes (Oriplast/Supreme)

32 mm CPVC sdr-13.5 pipes (Oriplast/Supreme)

Second floor

40 mm PVC SCH-80 pipes

50 mm PVC SCH-80 pipes

supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking G.I. Pipes and fittings/ P.V.C. pipes and fittings etc. all complete as per P.H. specification and direction of Engineer-in-charge.

Ground Floor :- 250 mm thick wall

Supplying all materials, labour, T&P and cutting hole in R.C.C floors, roofs, etc upto 19 cm thick for passing G.I. Pipes / P.V.C pipes and fittings etc and repairing the holes after insertion of pipes etc with cement concrete (1:2:4 ) including finishing complete so as to make it leak proof as per direction of the Engineer-in-charge.

Ground Floor :- 250 mm thick wall

Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking G.I./P.V.C. pipes and making good the damages as per direction of the E.I.C.

Ground Floor

First Floor

Supplying all materials, labour T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all joiniting materials complete as per specification and direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and fixing standard sized two way Bib cock of Hindware/Jaquar/Parryware of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Er-in-charge. 15mm dia CP Two way bib cock with Flange

Supplying all materials, labour, T&P and fixing standard sized Bib cock of Hindware/Jaquar/Parryware of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Er-in-charge.15mm dia. nominal bore Long body Bib Cock

Supplying all materials, labour, T&P and fixing standard sized Bib cock of Hindware/Jaquar/Parryware of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Er-in-charge.15mm dia. nominal bore Short body Bib Cock

Supplying all materials, labour, T&P and fixing standard sized 15mm dia angular Stop cock of Hindware/Jaquar/Parryware of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Er-in-charge. 15mm dia CP angle stop cock with wall flange

Supplying all materials, labour, T&P and fixing standard sized pillar cock of Hindware/Jaquar/Parryware of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. 15mm dia brass pillar cock

Fixing of 25mm dia Brass / Gun meta ball Valve confirming to IS : 781-1995 of approved make as per specification complete as per direction of Er-in-charge.32mm dia brass or gun metal full way valve

Fixing of 32mm dia Brass / Gun meta ball Valve confirming to IS : 781-1995 of approved make as per specification complete as per direction of Er-in-charge.32mm dia brass or gun metal full way valve

Fixing of 40mm dia Brass / Gun meta ball Valve confirming to IS : 781-1995 of of approved make as per specification complete as per direction of Er-in-charge.40mm dia brass or gun metal full way valve

15mm dia PVC connection pipe 450 mm long

15mm dia CP Extention Nipple

Providing and fixing circular type stainless steel jalli (grating) with hole for floor /nahani trap etc complete as per specification and direction of the Engineer in charge.

Supplying all materials, labour, T&P and fixing Health Faucet of Hindware/Jaquar/Parryware complete with Chromium plated brass brackets fixed to wooden plugs with Chromium plated brass screws as per specification and direction of the Engineer-In-Charge.

15mm dia CP Health Faucet of Jaquar 1.01mtr long,

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer-In-Charge.

In Building

110mm diameter U-PVC SWR pipes

110mm U-PVC door Tee

110mm U-PVC offset

110mm U-PVC door bend

110mm U-PVC plain shoe bend

110mm U-PVC vent cowl

110mm P-trap

110mm U-PVC plain bend

100mm S/S coupling with EPMD

Supplying all materials,labour T&P and cutting holels through existing brick or laterite masonry wall for taking H.C.I pipes and fittings including making good the damages etc. all complete as per P.H.Specification and direction of the Engineer-In-Charge.

250mm to 375mm thick wall

Supplying all materials, labour T&P and and fixing 12.50 liters/10 liters capacity low level flushing cistern of Hindware/Jaquar/Parryware with a pair of cast iron or M.S. brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle,unions and couplings for connection with inlet, outlet and overflow pipes, 32mm dia CP long flush bend, 15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connceting the inlet pipe with suupply main etc all complete as per the specification and direction of the Engineer-in-charge.

10 Liters capacity PVC cistern with 32mm dia flush bend.

Supplying all materials, labour, T&P and fixing vitreous china water closet, squatting pan (Indian type W.C pan/Orissa pattern squatting pan) of Hindware/Jaquar/Parryware duly embedded in cement concrete (1:4:8) using 4cm size hard granite metal including fixing a pair of vitreous china 250mm x 130mm x30mm footrest, fixing 100mm dia HCI 'p' or 's' trap (with/without 50mm dia horn) for water colset squatting pan including jointing the trap with pan in cement mortar (1:1) cutting the floor and mending good the damages etc all complete as per specification and direction of the Engineer-In-Charge.

Orissa Pan

Supplying all materials, labour, T&P and fixing the following vitreous china Wash Down Water Closet (Wall hung European type W.C. pan) of Hindware/Jaquar/Parryware with integral 'p' or 's' trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing etc all complete as per specification and direction of the Engineer-In-Charge.

Wall hung EWC with 'p' / S trap plain

Supplying & fixing of Matrix Set-1 (WB 46X36 with one pair mounting brackets, EWC & cistern complete with fittings & seat cover, one no hinged rail 76 cm and 4 nos of grab rail 60cm complete with all as per specification & direction of the Engineer in charge.

Supplying all materials, labour T&P and fixing wash basins of Hindware/Jaquar/Parryware with hole for pillar taps with cast iron or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, etc all complete as per specification and direction of the Engineer-In-Charge.

wall hung Wash Basin

Countersunk Wash Basin

Supplying all materials, labour T&P and fixing counter sunk Wash Basin Size - 545mmx545x180mm, Cat.No. FLS-WHT-29601 with all fittings as per direction of the engineer-in -charge.

Supplying all materials, labour, T&P and fixing Flat back large pattern urinal of Hindware/Jaquar/Parryware the following sizes including connecting the urinal with 32mm dia pvc waste pipe 910mm long by means of white lead mixed with chopped hemp, fixing 32mm dia CP dome waste, 15mm dia CP spreader including cutting holes in walls land making good the damages with supply of wooden plugs, screws and cement etc all complete as per specification and direction of the Engineer in charge.

Supply and fixing all materials, labour, T & P and providing urinal partition with italian collection (pastel)- size- 75x16.5x36.5 cm Cat no-61005 etc all complete as per direction of the Engineer-In-Charge.(Make-Merino)

Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm thick A.C.sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of the Engineer-in-charge.

B.E.mirro

Supplying all materials, labour, T&P and fixing standard size glass-shelf of Hindware/Jaquar/Parryware with CP brass brackets and guard rails complete fixed to wooden plugs with CP screws as per specification and direction of the Engineer-in-charge.

glass shelf

Supplying all materials,labour, T&P and fixing standard sized CP towel rail 24" of Hindware/Jaquar/Parryware complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer-In-Charge

25mmx600mm long CP towel rail

Supplying all materials, labour, T&P and fixing standard sized Chromium Plated brass towel ring complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and fixing standard sized Chromium Plated soap case of Hindware/Jaquar/Parryware complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge

CP soap holder

Supplying all materials, labour, T&P and fixing standard sized Robe Hook of Hindware/Jaquar/Parryware complete with all as per specification and direction of the Engineer in charge.

Supplying all materials, labour, T&P and fixing standard sized Soap Dispensor of Hindware/Jaquar/Parryware complete with all as per specification and direction of the Engineer in charge. Soap dispense with Glass Bottle.

Providing and fixing Salem Stainless steel A ISI (18/8) kitchen sink as per IS : 13983 with C.I. Brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required. a) Kitchen Sink with drain board Nirali make size 510 X 1040 mm bowl depth 178 mm.

Supply all materials, labour, T&P and providing fitting & fixing (Aqua guard) pure Chill 80 PSS UV of size 750x570x1350 mm height with water storage capacity 120 liters along with 2 nos of fancets 1 for cold water and 1 for normal water including a flow of 1.5 ltr per minute etc. all complete as per approved drawing, specification and direction of the EIC.

15.5l Aquaguard

Fixing Rotational moulded Poly Propelene double layer cylindrical vertical water storage tanks confirming to IS 12701-1996 including cutting holes through the tank and fixing mild steel tubes and fitting and providing extra sockets and jam nuts, fixing ball valve etc,including hosting upto a height of 5 mtr above ground level and placing the tank to the required postion etc all complete as per specification and direction of the Er-in-charge.

5000 ltr capacity Double layer cylindrical vertical water storage tanks

Supplying all materials, labour, T&P Providing, fitting & fixing of toilet Cubicle Fresh color restroom cubicles systems made out of the material and specification as detailed below: (Cubicle) (1000mm) (W)*1300mm (D)x2100mm (H) Door size:1925mm (H)x600mm (W), Divider size:1945mm (H), overall height of cubicle:2100mm (including bottom Gap of 100mm), Accessories> Satndard-Merino/Greenlam make, stainless steel-304 grade accessories), SS 'U'channel, SS "F" channel, SS coat hook, SS privacy thumb turn c/w occupancy indicator, SS door knob, SS hinges with cover, SS shoe box leg 12mm-316 garde, Rubber lining for groove, SS screws 304 G & PVC wall plugs, SS top rail (Special note: warpage critcria is 3.0mmx1000mm for MRS panels as per EN standard-438) etc. all complete as per direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and providing ceramic tiles in floors, treads and landing on 20mm thick bed of cement mortar 1:4 (1 cement:4 sand) joined with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing complete as per direction of the Engineer in charge. ( tile 600cmx600cm kajaria- Fogparla or equivalent makel to be pre-approved by the Engineer in charge)

GROUND floor

Supplying all materials, labour, T&P and fixing provide glazed tiles in dados skirting on 12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing complete as per direction of the Engineer in charge. tile 600x300cm size kajaria-Duren marfil or equivalent make to be pre-approved by the Engineer in charge)

GROUND floor

Supplying of filling sand in foundation and over areas including watering, ramming, consolidating and dressing, labours, tools, taxes etc. all complete as per the specification and direction of E.I.C.

Ground floor

SEPTIC TANK

UG TANK

Providing and laying plain cement concrete 1:3:6 (1 cement:3 sand: 6 stone agregate 40mm nominal size) as levelling course in foundation and plinth etc. including tempering, curring, shuttering etc. complete all depth and height.

Ground floor

SEPTIC TANK

UG TANK

Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard granite chips including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Ground floor

SEPTIC TANK

Supplying all materials, labour, T&P and providing Pidifin 2K including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Ground floor

Factory made single leaf solid WPC (wood polymer ) composite door shutter of 25mm thick compacted with wood grain finish structural foam paner of 29mm thickness and a density of 20kg/cu.mtr shall be used as core material for fitting the metal fittings such as tower blits,aldrops, handles etc shall be provided. A structural adhesive compatible with (EPS) foam shall be used for bending the core material ,The material and process for manufacturing the door shutters shall confrom to RV-TIFAC composites design centres standards and specification and the door shutters conforming to relevant I.S. specification . The finish of door shutter will be plain colour white /lvory/beige/light grey/mahogany/Teak wood or any other colour using high quality pigmments. Three heavy whight mild steel butt hinges type-I (ISI marked) size 100mm are to be fitted on one side of shutter.

Ground floor

Factory made solid WPC door frame of size 95mmx55mm fabricated .The door frame consist of four segments which are provided with plug-in-socket arrangement in-situ in the mould. The segments are plugged in and are joined together by means of screw . The WPC frame shall be provided with the material and process for manufacturing the door frames shall conform to relavent I.S Specification. the finish of door frame will be plain colour white /lvory/Beige/light grey/Golden brown/mahogany/Teak wood /sand stone/Champagne/pastel blue of any other colour using high quality pigments complete in all respect as per specification and direction of the engineer in charge.

Ground floor

Supplying all materials, labour, T & P and constructing Gully trap chamber of the following inside size with 8 cm thick R.C.C. precast cover slab in CC (1:2:4) mix using 12mm size h.g. chips, foundation concrete (1:4:8) using 40mm size h.g. metal on bed aound trap , Fly Ash brickwork in CM (1:6) in P&F and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mm x100mm size gully trap, 150mm x150mm C.I gratig etc. all complete as per aproved drawing, specification and direction of Engineer-in-charge.

250mmx250mm with RCC cover

Supplying all materials, labour, T & P and constructing Inspection chamber of the following inside size with CC (1:3:6) mix using 40mm size h.g. metal on bed, Ist class Fly Ash brickwork in CM (1:6) , moulding and shaping the channel inside and benching with CC (1:2:4) using 12mm size h.g. chips, 12mm thick cement plastering (1:3) finished with punning to inside , cement flush pointing (1:3) to outside , R.C.C. cover slab in (1:2:4) using 12mm size h.g. chips with RCC man hole cover , earth work in excavation in all kinds of soil and refilling the cavity around the chamber including watering ,curing, conveyance of all materials to worksite , payment of royality , taxes etc. all complete as per aproved drawing , specification and direction of Engineer-in-charge.

Inside size 760mm x760mm x450mm

Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized PVC pipes conforming to IS: 4985/2000 of the following outside dia for class-3(0.60mpa) including jointing with supply of approved solvent cement by non-heat application method/as per manufacturer’s specification, providing and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the Type C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per PH specification and direction of the Engineer-in-charge.

110mm dia u-pvc pipe alround concrete

160mm dia u-pvc pipe alround concrete

Supplying all materials, labour, T&P and constructing Man hole chamber of the following size with cement concrete (1:3:6) using 40 mm size HG metal on bed , !st class Fly Ash Brick work in CM (1:6) moulding and shaping the channel inside and benching with CC (1:2:4) mix using 12 mm size H.G chips, 12 mm thick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside ,RCC cover slab in (1:2:4) mix using 12 mm size H.G chips with RCC man hole cover , earth work in all kinds of soil and refilling the cavity around the camber including watering, curing, conveyance of all materials to worksite payment of royalty, taxes etc. all completed as per approved drawing, specification and direction of Engineer-in-charge.

Inside size 900mmx900mmx900mm

addl depth of 0.30m upto 4.50m depth

Supplying all materials, labour, T&P and constructing soakway pit of the following size with precast RCC rings joined loose, gravel backing in the rear of well steining, precast RCC cover slab in cement concrete (1:2:4) using 12mm size hg chips fitted with iron lifting handles including cutting hole in the rings for inlet pipe,earthwork in open well excavation in all kinds of soil and refilling of cavity around the pit & painting the iron works, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer-In-Charge

RCC rings soakway pit 1.8m dia x 2.6m deep

Rain water harvesting

Supplying all materials, labour, T&P and constructing Man hole chamber of the following size with cement concrete (1:3:6) using 40 mm size HG metal on bed , !st class Fly Ash Brick work in CM (1:6) moulding and shaping the channel inside and benching with CC (1:2:4) mix using 12 mm size H.G chips, 12 mm thick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside ,RCC cover slab in (1:2:4) mix using 12 mm size H.G chips with RCC man hole cover , earth work in all kinds of soil and refilling the cavity around the camber including watering, curing, conveyance of all materials to worksite payment of royalty, taxes etc. all completed as per approved drawing, specification and direction of Engineer-in-charge.

Inside size 900mmx900mmx900mm

Supplying all materials, labour, T&P and constructing soakway pit of the following size with precast RCC rings joined loose, gravel backing in the rear of well steining, precast RCC cover slab in cement concrete (1:2:4) using 12mm size hg chips fitted with iron lifting handles including cutting hole in the rings for inlet pipe,earthwork in open well excavation in all kinds of soil and refilling of cavity around the pit & painting the iron works, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer-In-Charge

RCC rings soakway pit 1.8m dia x 2.6m deep

Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized PVC pipes conforming to IS: 4985/2000 of the following outside dia for class-3(0.60mpa) including jointing with supply of approved solvent cement by non-heat application method/as per manufacturer’s specification, providing and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the Type C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per PH specification and direction of the Engineer-in-charge.

110mm diameter U-PVC SWR pipes

110mm dia u-pvc pipe alround concrete

BOREWELL

Construction of 1 No production wells including scientific source finding through consolidated and unconsolidated rock with down the hammer drilling rig or combination rig with PVC pipe and installation of submersible pump set with all acessories

Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories, tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (G.I/ P.V.C/ M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well), 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore only

Drilling of 200mm dia bore

00 mtr to 30mtr

30 mtr to 45mtr

Drilling of 150mm dia bore

45 mtr to above

Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity from ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and slotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials.

Lowering of 200mm dia P.V.C casing pipes

00 mtr to 30mtr

30 mtr to 45mtr

Supplying polyvinyl chloride pipes as per ASTM-D-1785-89 having threads in accordance with DIN 2999 part-1/DIN-42225 part-II specification length of pipe (laying length) will be 3 mtrs. The pipes shall be supplied with both external and threaded with free socket. The pipe having external thread at one end i.e female and or belled end. The female end having internal thread is to be belled in order to accept the male end while jointing pipes with a bore threading shall be provided with a greave at the roof of the male thread accomodate flexible PVC/Rubber 'O' ring to make the joint water tight colour of the pipe shall be blue. The name of the manufacture along with batch No class of pipe shall be stranded legibly of each pipe length.

200mm dia PVC (sch-80) pipe

Supplying all materials, labour, T&P and providing and providing sanitary sealing by cement concrete grouting of annular space around GI/PVC/MS housing pipe upto 5m below ground level (as per drawing) to plug the bore hole excluding cost of cement all complete as per direction of the Engineer in charge. Minimum one metre of casing pipe to be inserted in the bore into the rock at the bottom to ensure sanitary sealing (excluding cost of cement which will be supplied directly by the department)

Cleaning and developing the tube well with supply of compressor worked till clear and adequate discharge is obtained from the tube well including supply and use of all necessary equipment and labour as per direction of the Engineer in charge

By DTH Rig

Supplying all materials, labour, T&P and providing, fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase/1 phase line voltage ranging from 320 volt to 450 volt conforming to IS: 8034/89 with following specifications with suitable control panel, jointing with GI/PVC/HDPE pipes, electrification, testing, commissioning, trial running, conveyance of all materials to worksite, payment of taxes etc all complete as per specification and direction of the Engineer in charge (Texmo/Crompton Greaves/Kirloskar make)

1 H.P. Single phase/ three phase 3 stage head renge of 20 to 35 mtr with discharge capasity 145 to 110 L.P.M With outlet dia 25 mm (keeping 100% standby)

DOL Control panel

40mm dia steel short piece

Well cap

50mm size CI bracket

2.50sqmm flat cable

20mm dia rigid UPVC pipes

Steel rope with cover

Labour charges for lowering including transportation

Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor HDPE pipes and pipe fittings conforming to IS: 4984/2000 (10kgf/sqcm) of the following nominal bore with clamps and jointing by Fusion welding method including testing, making good the wall, ceiling and floor all complete as per specification and direction of the Engineer in charge

32mm HDPE pipes (Finolex/Supreme make)

Earthwork in excavation in all types of soil for site leveling, foundation, pits, trenches and other civil works up to and including 1.5 metre lift and stacking the soil upto a lead of 100 metre and including dewatering, removing slush, shoring and strutting (as required), complete as per specification and as directed by the Engineer-In-Charge.

SEPTIC TANK

UG TANK

Filling at all depth with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 15 cm in depth : consolidating each deposited layer by ramming and watering complete (lead upto 100m) as directed by the Engineer-In-charge.

SEPTIC TANK

UG TANK

Providing, lifting, hoisting and laying Reinforced cement concrete of M-250 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position.

SEPTIC TANK

a) Base

b) Wall/Beam

c) Slab

UG TANK

a) Base

b) Wall/Beam

c) Slab

Supplying, straightening, cutting, bending, placing in position and binding reinforcement steel work in RCC/reinforced brick works as per drawing and specification including preparation of respective bar bending schedule and binding (Binding wire to be used as per the IS code) etc. all complete as per direction of Engineer-In-Charge.Cold Twisted bars, Thermo-Mechanically-treated bars.

SEPTIC TANK

UG TANK

First class Fly Ash Brick masonry using F.A. bricks of size 25 cm. x 12 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix( 1:6) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar after immersing the bricks for 6 (Six) hours in water before use in Foundation & Plinth including splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as directed by the Engineer-in-Charge.

SEPTIC TANK

12mm cement plaster on internal smooth side of RCC/brick surfaces with cement mortar of mix 1:4 (1 cement : 4 fine sand) including neat cement punning & necessary scaffolding, curing etc. all complete at all floors and all heights.

SEPTIC TANK

Providing 16mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) with OPC 53 grade cement finished smooth to inside smooth surface of brick masonry walls after racking out the joints including watering and curing, rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge.

SEPTIC TANK

Supplying all materials, labour, T&P and providing , fitting & fixing 100mm x100mm x100 mm SW Tee in wall including filling the recess with cement concrete (1:3:6) with 12mm size h.g chips all complete including watering, curing, conveyance of all materials to worksite, payment of royalty all complete as per specification and direction of the Engineer in charge.

SEPTIC TANK

Supplying all materials ,labour, T&P and making MS STEP IRON IN 20MM diameter MS steel bars & fixing into walls of man hole/septic tank duly embedded in cement concrete (1:3:6) complete as per specification and direction of the Engineer in charge.

SEPTIC TANK

Supplying all materials, labour, T&P and providing Pidifin 2K including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

UG TANK

Supplying all materials, labour, T&P and providing cement punning including watering, curring and conveyance of all materials to site.

UG TANK

Supplying and fitting and fixing stainless steel 34 grade in said rail using 5mm dia 2mm thick circular pipe and balustrade 32mm x 32mm x 2mm below including welding welding with stainless steel elect rod and fixing with necessary accessories ete. complete as per direction of the Engineer-in-charge.

UG TANK

Providing fitting & fixing RCPC cover etc complete as per direction of Engineer -in-charge.

UG TANK

Please Enable Macros to View BoQ information