PM/RMM/e-Tender/CIVIL/25-26/20 (Sl.No.02) Dated.21.01.2026

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm. V/P-1, I-2(a),(b) & (e)(1), PWD SOR (Building)

Labour for laying 150 mm to 200 mm boulder soling including rough dressing hand packing and ramming down small pieces in the interstics including rolling and preparing the bed to proper level and filling up all joints with sandy clay or earth.(Analysed)

Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In ground floor including roof.(b) above 150 mm. thick V/P-10, I-2 PWD S.O.R(bldg.)

Dismantling carefully wooden walling, flooring of ceiling and stacking dismantled materials as directed.V/P-13, I-17 PWD S.O.R(bldg.)

Dismantling carefully wood work in posts, postplates, rafters, partition etc., sorting and stacking serviciable materials at site and removing rubbish as directed.V/P-13, I-19 PWD S.O.R(bldg.)

Rubble masonry in cement (1:6) with hard dressed stones from approved quarries and clean, coarse and washed sand including carriage of all materials to site(a) In Road and Jhora Work. V/P-22, I-44 PWD S.O.R (bldg.)

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (b) River bazree. V/P-26, I-10(ii), 3rd Corrigenda, PWD SOR (Building)

Ordinary Cement concrete (mix 1:2:4 ) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. (b) River bazree V/P-24, I-4(b), Sl-27 3rd Corrigenda, PWD SOR (Building)

Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor - (b) River Bazree - 1:3:6 proportion.V/P-17,Sl No-45,3rd Corrigenda, PWD SOR (Building)10 (i)

Plum concrete work with 40 % cement concrete with 30 mm down graded stone metal and 60 % stone boulder of size 150 mm and above, placed in position as directed excluding shuttering if any. ii) (1:3:6) proportion. V/P-27 & I-34 PWD S.O.R(bldg.), 3rd corrigenda

Hire and labour charges for Shuttering with or without staging upto 4.0 m height using approved stout props with wooden planks/ply wood/steel sheet plate with required bracing for any kind of plain or reinforced concrete works in all sorts of minor structure including culvert, box culvert, crossdrain etc. The rate is inclusive of fitting, fixing and striking out after completion of work as per specification and direction. (b) Where staging is not required. V/P-332, I-18.05 PWD S.O.R (Roads)

Supplying Labours

Clearing compound premises of shurbs, plants, jungles etc.by cutting and removing as directed. V/p-268, I-19 PWD S.O.R (Bldg)

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation, basement and upto roof of ground floor / upto 4 m. Tor steel. (iii) Other than I) In Ground Floor. V/P-44, I-40 (a) & (b), 10th corrigenda, PWD SOR (Building)

Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) (i) In Roof:- b) With 0.63 mm thick sheet. V/P-81, I-9 PWD S.O.R(bldg.)

Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work).(i) In Roof:- a) With 0.5 mm thick sheet. V/P-83, I-14 PWD S.O.R(bldg.)

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, iron butt hinges and M.s clamps(i) Other Local Wood. V/p-114,I-1 (i)PWD S.O.R (Bldg)

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.(iv) 75mm. X 47mm. X 1.70mm. V/p-140, I-5, PWD S.O.R (Bldg)

i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting. (b) 250mm long. V/p-141, I-10, PWD S.O.R (Bldg)

Supplying 'Godrej' mortice lock chromium plated with keys 6 levers including fitting & fixing complete. V/p-143, I-16, PWD S.O.R (Bldg)

Plain and furnished timber planks in partition, shelves etc. fitted and fixed complete as per design( butt joints) in ground floor. (iii) 25mm thick planks V/p-179,I-17 (iii)(c)PWD S.O.R (Bldg)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface].(II) With 1:4 cement mortar. (a) 20 mm thick plaster. i) In superstructure, ground floor V/P-189, I-1.ii., PWD SOR (Building)

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. V/P-192, I-15PWD S.O.R (bldg.)

Labour for Chipping of concrete surface before taking up Plastering work. V/P-192, I-1, PWD S.O.R (bldg.)

White washing including cleaning and smoothening surface thoroughly.All floors :(b) Two coats (to be done on specific instruction).V/p-194,I-1 (b)PWD S.O.R (Bldg)

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor)(b) Two Coatsi) Water based interior grade Acrylic Primer.V/p-195,I-7 (b)PWD S.O.R (Bldg)

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC.In Ground Floor:(b) Two CoatsV/p-196,I-8 (b)PWD S.O.R (Bldg)

Protective and decorative acrylic exterior emulsion paint of approved qua;lity as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required.The rate includes cost of material, labour, scaffolding and all incidental charging but excluding the cost of primer. In ground floor (Two Coat) a) Normal acrylic emulsion V/p-197,I-17 (a) PWD S.O.R (Bldg)

Priming one coat on steel/metal surface V/p-200,I-1(a) PWD S.O.R (Bldg)

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothing surface by sand paper etc. V/p-200,I-1(b) PWD S.O.R (Bldg)

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white). V/P-200, I-2 PWD S.O.R (bldg.)

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) i) Standard Quality V/p-201, I-4 PWD S.O.R (Bldg)

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall) (ii) 4 mm thick V/p-205, I-1 PWD S.O.R (Bldg)

Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (A) For Exposed Work. (a) (ii) 15 mm dia. medium quality. V/p-2, I-1 PWD S.O.R (Sanitary & Plumbing)

Supplying, fitting and fixing shower of approved brand and make. (a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model -Tropical / Sumthing Special of ESSCO or similar brand). V/p-3, I-3 PWD S.O.R (Sanitary & Plumbing)

Supplying, fitting and fixing shower of approved brand and make.(f) Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook(Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar).V/p-4, I-3 PWD S.O.R (Sanitary & Plumbing)

Supplying, fitting and fixing bib cock or stop cock. (a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand).V/p-6, I-7 PWD S.O.R (Sanitary & Plumbing)

Supplying, fitting and fixing bib cock or stop cock.(b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar. V/p-6, I-7 PWD S.O.R (Sanitary & Plumbing)

Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets. (i) 450 mm X 300 mm size. V/p-41, I-41 PWD S.O.R (Sanitary & Plumbing)

Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets. (a) Sink only. (i) 530 mm X 430 mm x 180 mm. V/p-42, I-6, PWD S.O.R (Sanitary & Plumbing)

Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.(ii) 450 mm long. V/p-43, I-9, PWD S.O.R (Sanitary & Plumbing)

Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.(iii) 900 mm long. V/p-43, I-10, PWD S.O.R (Sanitary & Plumbing)

Supplying fitting and fixing pillar cock of approved make. Pillar cock 15mm (Equivalent to Code No. 507 and Model Tropical/Sumthing special of ESSCO or similar brand V/p-45,I-19(a)(i) PWD S.O.R ( Sanitary and Plumbing)

Supply of galvanised iron socket with I.S.I. mark. (i) 15 mm dia

Supply of galvanised iron socket with I.S.I. mark. (ii) 20 mm dia.

Supply of galvanised iron socket with I.S.I. mark. iii) 25 mm dia.

Supply of galvanised iron socket with I.S.I. mark. (v) 40 mm dia.

Supply of galvanised iron socket with I.S.I. mark. (vi) 50 mm dia.

Supply of G.I. reducing socket with I.S.I. mark. (i) 20 mm

Supply of G.I. reducing socket with I.S.I. mark. (ii) 25 mm

Supply of G.I. reducing socket with I.S.I. mark. (iv) 40 mm

Supply of G.I. reducing socket with I.S.I. mark. (v) 50 mm

Supply of G.I. bend. (i) 15 mm

Supply of G.I. bend. (ii) 20 mm

Supply of G.I. bend. (iii) 25 mm

Supply of G.I. bend. (v) 40 mm

Supply of G.I. bend. (vi) 50 mm

Supply of G.I. plain equal elbow of approved brand and make. (i) 15 mm

Supply of G.I. plain equal elbow of approved brand and make. (ii) 20 mm

Supply of G.I. plain equal elbow of approved brand and make. (iii) 25 mm

Supply of G.I. plain equal elbow of approved brand and make. (v) 40 mm

Supply of G.I. plain equal elbow of approved brand and make. (vi) 50 mm

Supply of G.I. plain tee of approved brand and make (i) 15 mm

Supply of G.I. plain tee of approved brand and make (ii) 20 mm

Supply of G.I. plain tee of approved brand and make (iii) 25 mm

Supply of G.I. plain tee of approved brand and make (v) 40 mm

Supply of G.I. plain tee of approved brand and make (vi) 50 mm

Supply of G.I. nipple standard 50 mm long. (i) 15 mm

Supply of G.I. nipple standard 50 mm long. (ii) 20 mm

Supply of G.I. nipple standard 50 mm long. (iii) 25 mm

Supply of G.I. nipple standard 50 mm long. (v) 40 mm

Supply of G.I. nipple standard 50 mm long. vi) 50 mm

Supply of long screw (150 mm long) of TATA make with sockets (TATA make) and jamnut.(i) 15 mm

Supply of long screw (150 mm long) of TATA make with sockets (TATA make) and jamnut.(ii) 20 mm

Supply of long screw (150 mm long) of TATA make with sockets (TATA make) and jamnut.(iii) 25 mm

Supply of long screw (150 mm long) of TATA make with sockets (TATA make) and jamnut.(v) 40 mm

Supply of long screw (150 mm long) of TATA make with sockets (TATA make) and jamnut.(vi) 50 mm

Supply of G.I. union. (i) 15 mm

Supply of G.I. union. (ii) 20 mm

Supply of G.I. union. (iii) 25 mm

Supply of G.I. union. (v) 40 mm

Supply of G.I. union. (vi) 50 mm

Supply of G.I. short piece of TATA make (Above 50mm & upto150 mm long) (i) 15 mm

Supply of G.I. short piece of TATA make (Above 50mm & upto150 mm long) (ii) 20 mm

Supply of G.I. short piece of TATA make (Above 50mm & upto150 mm long) (iii) 25 mm

Supply of G.I. short piece of TATA make (Above 50mm & upto150 mm long) (v) 40 mm

Supply of G.I. short piece of TATA make (Above 50mm & upto150 mm long) (vi) 50 mm

Non schedule Item (Rate should be analysed from present market rates of different element in the item against documentary evidence with 5% overhead charge 10% contractors profit & 1% BOCWW Cess towards BOCWW Act 1996. In that case contractual rate will not be applicable

Items covering based on P.W. D ., S.O.R ( Bldg w.e.f 01.11.2017 (15th corrigenda 07.09.2022) & Roads & Bridges w.e.f 30.08.2018 (10th corrigenda 24.08.2022) and S&P w.e.f. 01.11.2017 (7th corrigenda dtd. 22.01.2020)

Add BOCW cess @1% on the rate of all above items

Please Enable Macros to View BoQ information