Providing GWSS Gurguri Majhgaon in GP Rupi Tehsil Nichar Distt Kinnaur HP

Amount

Excavation in foundations in all kinds of soil such as pick work ,jumper work, blasting hard or soft rock chiseling where blasting is prohibited or saturated soil , lift upto 1.50 mtr stacking the excavated soil not more than 3.00 mtr clear from the edge of the excavation and then returning the stacked soil in 15 cm layers when required into plinth sides of foundation consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth as directed with a lead of 20 mtrs. P/J Work .

Providing and laying cement concrete 1:3:6 (1 cment:3 sand: 6 graded stone agg. 40mm Nominal size) and curring complete excluding the cost of form work in foundation & plinth

Providing & Laying Cement Concrete 1:1/2:3 (1 Cement:1/2 Sand:3 Graded Stone aggregate 20mm nominal size) and curing complete excluding the cost of form work in foundation and plinth.

In foundation footing, bases of columns and like & mass concrete.

Walls (any thickness but not less then 0.10 mts.thickness ) attached pillaster, buttreses plinth & string course etc.from top of foundation level upto floor two level.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in:

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillaster buttresses, plinth and string courses and the like with in all leads and lifts.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Lloors etc. upto 200mm. In thickness with in all leads and lifts.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1cement:3 sand)

Providing and laying cement concrete 1:2:4 (1 cement: 2 sand: 4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in:- Suspended floors ,roofs,landing and shelves and their support, balconies ,beams, girders,bressumers and centileaver upto floor two level.

Providing tor steel reinforcement for RCC work i/c bending, binding and placing in position complete upto floor two level (tor steel)

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting, fixing in position and applying a priming coat of red lead paint. In gratings framed guard bars,ladders,railling,brackets and similar works.

Manufacturing and supplying of MS Wheel Valve Chamber of size 450x450x450mm made of 2.0mm MS Sheet fixed on top & all four sides with ISA 35x35x4mm frame as per drawing. Pieces of MS Flat 20x4mm, 0.10m long be fixed on all sides as hold fast. The operation of manufacturing shall including cutting of MS Sheet, Angle Section & welding of MS Sheets, Angle Section, Hinges, Handles 150mm long, 20x4mm flats, locking arrangement and applying a priming coat of steel primer after pretreatment of surface to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing of MS Sheet Manhole cover angle iron (65mmx65mm)frame of size 0.65x0.65 welded with MS sheet 16 gauge. Within all leads and lifts ( Waight of cover and frame not less then 35 kg)

Laying & Jointing in treanches GMS tube (MG) and tube fitting (earth work in trenches to be measured and paid seprately) as per the direction of the Engineer-in-Charge including all fittings complete.

65mm dia

50mm dia

Providing and fixing wheel valve (with hand wheel)

65mm dia

50mm dia

M/S MOHAN SINGH (BID ID -541792)

ABHISHEK KUMAR (BID ID -541745)