CERTAIN REPAIR TO TOILET BLOCK AT OTM ACCN UNDER AGE B/R I AT AMRITSAR CANTT UNDER GE ASR

Amount

Dismantling of roof brick tiles fixed in cement mortar in single layer complete all as specified and directed.

Demolition mud phuska in roofs any thickness including plastering and leeping complete all as specified.

Roughing the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L Cement concrete 1:2:4 type B-0 using 12.50mm graded crushed stone aggregate as in roof padding avg 50mm thick complete all as specified.

M&L for 10 mm thick cement plaster in CM (1:3) using WPC on RCC roof slab including cleaning of existing surface complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

Material and labour for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application over a tack coat of in dustrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified

M&L for Cement concrete tiles 20cmx20cmx20mm thick,machine pressed ; set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment, and cut and polished over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Demolition of cement concrete above ground floor and in any position complete all as specified and directed.

M&L plaster 15mm thick in cm 1:3 in sunken portion of slab with using waterproofing compound and providing 3mm thick superior Atactic Polyprophylene modified ploymeric membrane waterproofing treatment of weight not less that 3.6 Kg per sqm with properties of high penetration and the centre core consiting of 90 micron high molecular -High Density polyethylen (HMHDPE) film consiting of 5 layers. The superior multi polyplus is to be laid after preparing the surface by cleaning throughly to achieve a smooth surface over and including evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed.

M&L for PCC 1:5:10 type E2 using 40 mm stone agg filling fdn and mass concrete in sunken floor complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified.

Taking down cement plaster on brick, concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. Of any description complete all as specified and directed.

M&L for 15mm thick cement plastering in cm 1:6 on brick or concrete surfaces other than fair surface, finished the surfaces even and fair without using extra cement complete all as specified and directed.

M&L for 10mm thick cement plastering in CM 1:3 on ceiling surfaces other than fair surface, finished the surfaces even and fair without using extra cement complete all as specified.

M&L for 15mm thick cement plastering in cm 1:4 on brick or concrete surfaces other than fair surface, finished the surfaces even and fair without using extra cement complete all as specified.

M&L preparation of new plaster surface and applying two coats of Oil bound distemper of wall over a coat of chalk whiting primer on wall complete all as specified and directed by EIC.

M&L preparation of new plaster surface and applying two coat of white wash on wall complete all as specified and directed by EIC.

M&L preparation of new plaster surface and applying two coat of white wash on ceiling complete all as specified and directed by EIC.

M& L for one coat of white wash on old treated ceiling surfaces complete all as specified and directed.

M & L for preparation of old decorated wall surfaces and applying one coat of white wash complete all as specified.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats ) complete all as specified.

All as per Srl Item No 23 here-in-before but exc 1.50sqm but n.exc 4Sqm complete all as specified and directed.

S&F pressed steel frames 1.25mm thick for door size of frame 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges complete all as specified and directed.

S&F WPC frame of size 65x100(single rebated) as specified and directed(For toilet door).

S&F 30mm thick factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to e fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F 35 mm thick flush shutter, soild core construction, with block board core and plywood face panel commercial type on both sides complete all as specified and directed.

S&F mild steel work Fe 410-W(Gde-E- 250) quality-A Fe in framed work as in door frame, shutter or gates of angle iron or other section with gusset plates,rails,braces etc complete drilled for fixing of steel sheeting or orther covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening complete all as specified and directed

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

S&F aluminium anodised barel tower bolt of extrud sec 150mm long ISI marked complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extrud sec 200mm long ISI marked complete all as specified and directed.

S&F Extruded aluminium alloy handle fabricated type anodized of size 125 mm long ISI marked complete all as specified and directed.

S&F Extruded aluminium alloy handle fabricated type anodized of size 150 mm long ISIS marked complete all as specified and directed.

S&F 300mm long aluminium alloy,anodised , sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded sectionsor cast aluminium alloy complete all as specified and directed.

Material and Labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. NOTE : MS guard bar 10mm square bars@ 10c/c fixed horizontally, 3mm thick clear glass sheet-3 Nos per leaf glazing with oil putty and stainless steel wire cloth, 036 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in each leaf. Note:- including taking down old steel/wooden window including hold fast PCC 1:2:4 type B0 (four Nos for each window)& around required plaster in CM 1:4 and match with existing finish complete all as specified and directed by Engineer- in-Charge. painting shall be meausered and paid seperately.

S&F figured glass pin head type, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty complete all as specified and directed.

S&F rotational moulded polytheylene triple layered white water storage tanks of capacity 500 Litres(cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia brass float valve with brass rod complete all as specified.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified.

Taking up and down GI pipe15mm bore including fittings, connection, including cleaning for refixing in any position complete all as specified and direced.

All as per Srl Item No 40 here-in-before but 20mm bore of pipe complete all as specified and directed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings incl taking down ISI marked complete all as specified.

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings incl taking down ISI marked complete all as specified.

S&F in repair bib taps 15mm dia chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed.

S&F in repair stop valves(Concealed cock) 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified.

S&F in repair stop valve/angel valves 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified.

S&F in repair CP shower rose 125 mm size with swivel joint fancy type including fixing to steel pipe or union complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc including lime concrete in lime mortor 1:3 usisng broken bricks 40mm graded coarse aggregate complete all as specified. Note:- Flush pipe and flushing cistern to be measured and paid separately.

S&F in repair PVC low level flushing cistern 10ltr capacity, with syphonic action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified and directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair Vitreous china wash basin,white flat back,size 630x450mm excluding taps but including brackets,32 mm waste pipe and 32mm PTMT waste coupling complete all as specified and directed by EIC.

S&F in repair Pillar taps 15mm bore, cast copper alloy but fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified & directed by EIC.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long embedded in the wall complete all as specified & directed by EIC.

S&F towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified & directed by EIC.

S&F aluminium anodised towel rail `D’ type 60 Cm long fixed to wall complete all as spd and directed by EIC.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required complete all as specified and directed.

S&F 110mm bore PVC (SWR) ISI marks pipes single socketed in any length with rubber ring joints fixed to wall or floor upto 12m height complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or floor upto 12m height complete all as specified and directed.

S&F PVC (SWR ) bends 75 mm bore any radius complete all as specified and directed.

S&F PVC (SWR ) vent cowl 110 mm bore complete all as specified and directed.

M&L PVC (SWR ) floor trap 110/75 mm plain with grating incl. jointing with solvent cement as per site requirement complete all as specified and directed.

S & F Stack clamps (110 mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

All as per Srl Item No 63 here-in-before but 75 mm complete all as specified and directed.

M&L for preparation of new painted wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of primer complete all as specified and directed by EIC.

M&L for preparation of new painted steel surface exc 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed by EIC.

Demolation of brick work built in cement mortar or cement lime mortar as cutting, opening of exsiting wall complete all as specified and direced.

M&L for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and directed.

M&L for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, in half brick thick walls and built in CM 1:4 complete all as specified and directed.

Demolition of Stone slabs and tiles of laid, beded and pointed of any mortar in any description or thickness in floors, aprons etc complete all as specifed an directed by EIC.

M&L Granite (of any type) work (table rubbed and polished) 20 mm thick in steps , jambs, pillars, window cills, cooking plateforms and like in cemnet mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 complete all as specified and directed.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level complete all as specified an directed.

M&L for 75mm thick cement cocnrete type C-1 (1:3:6) (20mm graded aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed by EIC.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 complete all as spcified and directed by EIC.

M&L for glazed ceramic coloured tiles in vertical surface of size 350x250x7mm/ 450x350x7mmmm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles complete all as speciifed and directed by EIC.

Material and Labour for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1 : 2 : 4) using 12.5mm graded crushed stone aggregate and reinforced with 10mm TMT bars with or without facia and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of Finishes to match with the existing surfaces in upto 12m height all as specified & directed. Note: - Cost of formwork and welded mesh, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

Demolition of cement concrete (Reinforcment) of any description all as specified & directed.

M&L for RCC in 1:2:4 type B-0(using 12.5 mm graded stone agg) as in chajjas facia, shelves, lintel etc and similar work complete all as specified and directed.

Form work to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs upto 12m height complete all as specified and directed.

S&F 10mm dia over TMT bar cut to length bent to shaps including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securingwith clips complete all as specified and directed.

M&L TMT bars 6 to 8mm dia and over cut to length bent to shape required including crancking spirally for hooking ends and binding with and including MS wire annealed n.less than 0.9mm dia complete all as specified.

S&F rotational moulded polytheylene triple layered white water storage tanks of capacity 1000 Litres(cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia brass float valve with brass rod complete all as specified.

Supply and fixing 5 mm thick PVC sheet as in back side of kitchen cabinet etc complete al as specified.

Supply and fixing18 mm thick PVC sheet shutter one side prelaim of any shade as in kitchen cabinet etc complete all as specified.

Supplying and fixing 40 mm long hinges self closing type hydrulic type complete all as specified.

Providing and fixing plain basket SS of size 470x485x200 mm of godrej (Product Code 5904) or equivalent to be fixed with drawer as per manufacturer instructions complete all as specified and directed.

Providing and fixing soft closing drawer channel 500mm long of godrej (Product Code 7087) or equivalent to be fixed with drawer as per manufacturer instructions complete all as specified and directed.

Supplying and fixing 75 mm long SS handle fixed to cupboard shutter complete all as specified.

S&F of Vitreous china wash down water closet pan( pedestal pattern), white complete all as specified and directed. Note:-Rate of supply for Flushing cistern, flush pipe, seat cover etc have been taken separately.

Supply only Plastic water closet seat,white/ivory,closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device (Toilet Seat Cover) complete all as specified and directed.

Supply and fixing Chromium plated Health faucet in repair with 1.5 metre long chain complete all as specified and directed.

S&F in repairs CP wall mixer with telephonic shower arrangement and telephonic shower suitable for 15mm dia bore pipe complete all as specified and directed.

S&F glass corner of 30cm radius made of 5.5mm thick sheet galss with CP guard rails fixed to walls with brackets complete all as specified and directed.

S&F CP brass towel ring of appropriate size not exceeding 45cm dia as approved by Engr-in-charge/GE complete all as specified and directed.

S&F in repairs PVC Mirror cabinet with shelves of best quality including fixing arrangements size 350x450mm complete all as specified and directed.

S&F centre hole mixer cast copper alloy chromium plated with capston head srewed down high pressure with lettered hot or cold with long screwed shanks fly nut screwed for iron pipe 15mm dia complete all as specified.

S&F in repair of One piece ceramic floor/wall mounted EWC with features like twin flush system, noisless soft close seat cover, anti-bacterial surface white with PVC(SWR) 'P' / 'S' trap 110/110mm bore complete all as specified and directed. Make: CERA/Kerovit/Jaquar

Supply & Fixing vitreous china urinal half stall type with CP spreader white incl CP waste coupling with grating and union fordischarge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed.

S&F Vitrous china urinal partition white of size 310x770mm and fixed to wall terminating about 40cm above floor line complete al as specified and directed.

Demolition of cement concrete above ground floor and in any position complete all as specified and directed.

M&L for 100 mm thick hard core of broken stone of gauge not exc 63 mm, deposited , spread and levelled , watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type B-2 (using 40 mm graded stone aggregate) in Path complete all as specified and directed.

M&L for 25mm thick sand filling under floors or tiles/stone complete all as specified and directed

M&L for providing precast cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) fixed in CM 1:4 in kerb stone etc complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade with grey cement and pigment complete all as specified and direcated.

S&F powder coated aluminium frame for doors ,windows, ventilators with one or more rebates including joining cleats for fixing complete all as specified and directed by Engineer-In-Charge. (Min. thickness of powder coating 50 micron)

S&F powder coated aluminium glazed shutter(for doors) Al-section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading complete all as specified and directed. ( Min. thickness of powder coating 50 micron)

S&F Aluminium powder coated (of any colour) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. (Min. thickness of powder coating 50 micron)

ESS KAY BUILDER

GEE EMM ASSOCIATES

MAAN ENTERPRISES

Harai Sharan Govt Contractor

B.J.CONSTRUCTION CO

M/S SHRI RAM BUILDERS

M/s. M Company