SPECIAL REPAIR TO TRANSMITTER BUILDING UNDER GE(AF) TECH AREA AT AF STN AGRA

Amount

Demolition Brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified.

M&L brick work with sub class 'B' brick straight or curved on plan exc 6 metres radius with old size bricks built in cement mortar (1:4) complete all as specified and directed

Taking down cement plaster in cement or cement lime mortar of any description, on brick or stone walls, concrete surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc, and removal of debries out side MOD land complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces and finish the surface even and smooth without using extra cement complete all as specified and as directed.

M&L rendering 15 mm thick on other than fair faces of brick work or concrete surfaces , in cement and sand mortar 1:6 and finish the surface even and smooth without using extra cement complete all as specified

M&L for preparation of new plastered surfaces of Wall and applying two coats of weather proof exterior emulsion paint in normal pattern , over a coat of primer as per manufacturers instructions complete all as specified and as directed.

M&L for two coats of distemper oil emulsion over newely plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for providing & applying average 1mm thick of Birla/ JK wall care putty over prepared surface to achieve the surface even and smooth for painting, complete all as specified and as directed

M&L for rendering 10mm thick in CM (1:3) on ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for prepration of new plastered ceiling surfaces and applying three coat of white washing complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding and removing rubbish off the premises complete all as specified and as directed

M&L for glazed ceramic coloured tiles 300x450x 7mm thick as in dado with and including Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM (1:4), set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and as directed

Demolition of cement concrete ( unreinforced ) in ground floors and pavings not exceeding 15 cm thick above or below ground level complete all as specified and directed.

M&L for 40 mm thick PCC(1:2:4) type B0 using 12.5mm graded stone aggregate as in sub base of floor etc complete all as specified and directed.

M&L for 8-10 mm thick Vitrified ceramic tiles, light shade double charged (square/recangular) area of each tile exceeding 0.36 Sqm n exceeding 0.42 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed

M&L light shade colour vetrified ceramic tiles 10mm thick (square/rectangular ) polished, area of each tiles n.exc 0.06 sqm as in skirting /dado etc laid over and including 10 mm thick rendering / backing coat in CM 1:3, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards any thickness and in any position including cover fillets complete all as specified and as directed.

S&F 605mm x 605mm anodised aluminium snap grid frame work for false ceiling and 4 mm thick non asbestos fibre cement building board of approved make and Block / Sparkle / Floating / Prism / Diamond / Honey-comb / Puff / Stone-wall / Zig-zag / Leaf / Smoke / Strip Design ,fixed or laid/ inserted to Aluminium frame work with screws as per manufacturer's instructions complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550MPa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed..

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550MPa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed...

S&F mild steel works as in wind ties for roof incl securing bolts; posts and struts in fencing incl cutting tops to shape as directed , drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc) incl all necessary drilling, bolting or riveting etc and similar work conforming to Fe 410-0 or Fe 310-0 upto any height of bldg complete all as specified and directed.

S&F 2 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in roof, wall etc complete all as specified and directed.

S&F for aluminium anodized powder coated deco grills with 6 x 5 mm aluminium section having square gap of 50 mm thick with fixing rails of channels 12-15 mm complete all as specified and as directed

M&L for preparing new decorated wooden or wood based surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection, path / hardstanding / subbase etc complete all as specified and directed .

M&L Chequered cement concrete tiles with white cement and pigment of size 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry incl 15mm thick Screed bed or bedding layer of cement mortar 1:4 for laying tiles complete all as specified and directed.

Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutters from the frame) incl repairing of jambs in CM 1:4 complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specification and shown in drg in SSR Part -II 2020 complete all as specified and as directed

S&F factory made solid panel PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain cover PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading sheet and jointed together with solvent cement in frame at site as per specification and shown in drg in SSR Part -II 2020, including all necessary fittings complete all as specified and as directed

S&F for Pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and as directed

S&F 30 mm thick ,2nd class Hard wood (Sal), plain framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats ,incl all necessary fittings complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan (padestal pattern) with seat cover (excluding fixing bolts, flushing cistern and flush pipe) etc complete all as specified and as directed.

S&F flushing cistern 10Ltr capacity PVC valveless, syphonic action type, low level, dual flush, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in repair 15 mm dia bib tap cast copper alloy, fancy type chromium plated ,'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F for Wash basins, Vitreous China (flat back or angle back type) size 580X450mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe , complete all as specified and as directed.

S&F fancy type 15 mm dia Pillar taps/bib tap ,cast copper alloy ,with capstan heads chromium plated screwed down high pressure, with or without letterd HOT or COLD with long screwed shanks and fly nuts ,screwed for iron pipe and fixed complete all as specified and as directed.

S&F soap dish tray embedded in wall , vitreous china white, approximate size 160x160x90 mm complete all as specified & directed.

S&F brass CP Stop valve/ Angle valve 15 mm fancy type with long shank and cup (concealed type) fixed complete all as specified and as directed.

S&F for PVC connection 15mm size with brass nuts of length 450mm complete all as specified & directed.

Taking up or down 15 mm bore steel tubing and connections, complete all as specified and as directed

Taking up or down 20 mm bore steel tubing and connections, complete all as specified and as directed by Engr-in-charge.

Supply and fix 15 mm bore galvanized steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line all as specified and as directed

Supply and fix 20 mm bore galvanized steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line all as specified and as directed

S&F Aluminium Partition wall of section as in frame size 63.5 X 38.1 x 1.0mm thick incl 5mm thick Glass / 12mm thick prelaminated particle board paneling including MS Channel ( Size of panel n.exc 1.5 Sqm each ) and all necessary fittings with and including taking out old partition wall frame including accessories complete all as specified and as directed

Dismantling PVC water tanks of capacity exc 500 ltrs but n.exc 1000 ltrs in any position and removing from site complete all as specified and as directed.

S&F tripple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I of 1000 ltrs capacity with & including 20mm dia PTMT float valve complete all as specified and directed.

S & F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc conforming Fe 410 -W (Gde-E- 250) quality-A complete all as specified and directed.

S&F for mild steel work as in posts or struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary bolting or riveting and spot welding etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L for 20 mm thick screed bed in cement mortar 1:4 complete mixed with water proofing compound @ 3% by weight of cement or as per manufacturers instructions over roof top surface finished even and smooth using extra cement and application of water proofing treatment using APP modified roof membrane over existing accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed. (a) Cleaning existing surface properly. (b) Applying primer @ 0.30 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (d) APP membrane shall be laid using butane torch by torch application with minimum 10cm side overlap and 15cm end lap.

M & L for prepararing new decorated surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of aluminium paint complete all as specified and directed.

M&L for Framed work in doors or gates of angle or other section with gusset plates, rails bracers etc complete, drillid for fixing of steel sheeting or other covering. Doors etc to be repaired for hanging or sliding with and including either hooks and hungs or steel hanging door fittings and hanging, also fastening and fixing complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section,embedded in concrete including taking out embedded portion and making good disturbed ground complete all as specified & directed.

M&L for Providing cement concrete type D-2, 1:4:8 ( using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified & directed.

M&L for mild steel work as in posts or struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary bolting or riveting and spot welding etc and similar work conforming to Fe-290 Gde E-165 complete all as specified & directed.

S&F Galvanised, 2 strand, steel barbed wire 2.24 mm dia, barbed with 2 mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc as directed (each line of wire to be measured)

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, n. exc 5cm long , diameter of neck 5 to 10mm complete all as specified & directed.

Supply only chain link fencing mild steel galvanised fencing any size and type (size of mesh and dia of wire as directed by Engg-in-charge) all as specified.

Fixing only chain link fencing including line wires, any mesh size and type to any type of standards , rails, straining bolts etc. including provision of binding wire complete all as specified.

S&F Mild steel round bars 10mm dia and over as in strengthning bars for chain link fencing conforming to Fe-290 Gde E-165 complete all as specified & directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth, not otherwise described and apply two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified & directed.

M&L for preparation of new steel surfaces of any description not exc 10 cm width or girth, not otherwise described and apply two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified & directed.

S&F in repair venetian blends in double layers roller type of approved colour including all items for fixing the same in windows complete all as specified and as directed.

M&L for 40 mm thick PCC(1:2:4) type B0 using 12.5mm graded stone aggregate as in sub base of floor etc complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-22mm thick over cement screed base laid and jointed with incl 15mm thick screed bed in CM 1:6 laid jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

Demolition of RCC of any description and in any position complete all as specified and as directed

M&L for M-25 design mix (using 20mm graded stone aggregates) as in RCC work Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified & directed.

M&L MS deformed or twisted bars 10mm dia & over , cut to length bent to shape required including cranking bending spirally for hooping columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips provided in RCC members complete all as specified and directed.

Use & waste of Form work to chajjas, throughs and similar items including edges, with fair finished flat surface complete all as specified

S&F MS butt hinges cold rolled medium weight of size 100mm complete all as specified and as directed.

S&F 150 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and as directed

S&F 100 mm long aluminium anodised handle fabricated type complete all as specified and as directed

S&F 150 mm long aluminium anodised handle fabricated type complete all as specified and as directed

S&F 300 mm long mild steel sliding door bolt clip and bolt type, stove enammelled black with bright bolt not less than 12mm dia with and including minimum 06 bolts and nuts, four on bolt plate and two on staple complete all as specified and as directed

Taking down carefully Aluminium/copper point wiring (Light/ Fan/Socket or power) complete incl fitting fixture such as switches, sockets, ceiling rose, brackets, holders, bulk head fitting etc and making good disturbed surface of wall / ceiling etc. to match with the existing surfaces complete all as specified and directed.

Taking down main switch/MCB DB/AC enclosure/Three phase enclosure by disconnecting the electric supply complete all as specified and as directed.

Taking down old XLPE cable of any size up to 50 Sqmm from wall/ceiling/truss/duct by disconnecting the electrical connection and descrewing the saddle clips/clamps and keeping aside to reuse the same after ceiling work complete all as specified and directed.

Laying only the XLPE insulated LT cable retrieved from taking down of size up to 50 sqmm on wall/ceiling/truss/duct with clamping on every meter by saddle clips/clamps of suitable size complete all as specified and directed.

Taking down old U/S sub main wiring 4 Sqmm/6 Sqmm/10 Sqmm aluminium/copper including batten/conduit and making good disturbed surface to match the existing surface complete all as specified & directed.

M&L for point wiring complete with stranded copper conductor 1.5 Sqmm size (Nominal area) PVC insulated unsheathed cable FRLS in and including concealed PVC conduit ISI marked medium grade not less than 20mm dia with all accessories such as TEE, bend,elbow,reducers,sockets and junction boxes etc, concealed sunk in pressed steel terminal boxes of reqd size of thickness 1.6 mm factory made and painted with stove enameled black paint and bituminous coat of external portion to prevent the rust with top cover 3mm thick plastic laminated sheet of required colour fixed with brass screws and cup washer including 1.5 sqmm stranded copper conductor PVC insulated cable of green colour as earth continuity connected to common earth dolly and all sunk/terminal boxes and each fitting/fixture, all cable ends will be terminated with suiable brass thimbles to prevent the heating of termination point complete One light/fan/exhaust fan point controlled by one way 5 Amp switch.with all accessories all as specified and directed: - Note : Conduiting on the wall shall be concealed but if it is not posible to conceal the conduit on the RCC roo/crossing of column/beam then it shall be fixed on surface as per the condition of site.

All as per Ser Item No 82 above but One 3 pin/5 pin socket out let 5 Amp on independent board with indipendent circuit from DB box.

All as per Ser Item No 82 above but OneOne 3 pin/5 pin socket out let 5 Amp same board

All as per srl item no. 82 above but for 3/5 pin socket outlet for 15 Amps on independent board with indipendent circuit drawn from DB box with 2.5 sqmm PVC insulated, unsheathed single core multistranded copper conductor cable 1100 volts grade including 2.50 sqmm PVC insulated unsheathed solid copper conductor cable as earth continuity conductor complete all as specified & directed.

S&F switch piano, flush type 5 Amp single pole one way complete all as specified & directed.

S&F switch piano, flush type 15 Amp complete all as specified & directed.

S&F socket out let, flush type 5 pin 5 Amp complete all as specified & directed.

S&F socket outlet multi purpose 3 pin 15 Amp and 3 pin 5 Amp, flush type complete all as specified & directed.

S&F ceiling rose surface bakelite ISI Marked three terminal complete all as specified & directed.

S&F lamp holder PVC/polycarbonate angular/batten type with back plate fancy type with three terminals isolated body all as specified.

S&F stepped type Electronic fan regulator flush mounted socket type complete all as specified and directed.

S&F in renewal of heavy duty exhaust fan steel body AC single phase 230 volts ,50 Hz of size 300mm sweep , 900 rpm with blades, frame and louvers fixing with cutting the existing wall of adequate size in round shape , making good the disturbed surface with cement mortor and grouting the louvers and nut bolts of exhaust fan complete all as spacified and directed.

Supply and Fixing in renewal of LED luminaire 600mmX600mm, 36 Watt, AC 230 V recessed type with high effeciency PMMA diffuser soft glare free light complete with driver, holders&LED lamp suitable for roof, ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and Fixing in renewal of the LED tube light fitting 1x20 Watt , AC decorative box type with driver , holder including LED tube light connecting up with three core flexible copper conductor of suitable size from ceiling rose to fittingand all as specified and directed.

S&F in renewal of LED light fitting mirror type with high output diffuser 2feet, 10 watt AC 230V decorative type with driver , holder and LED lamp including connecting up with driver three core flexible copper conductor of suitable size from ceiling rose to fittingand all as specified and directed.

Taking down ceiling fan and refixing the same of any type and size painting of ceiling fans with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust and regreasing, oiling and safety clips complete with all fitting connecting up fan with three core flexible copper conductor of suitable size from ceiling rose to fan and all as specified and directed. etc. removing materials deposit to store for keeping in safe custody till refixing.

S&F in renewal of sheet metal enclosures with socket plug top and MCB single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20Amp MCB ,240 volts complete all as specified and as directed by the Engineer in charge

S&F in replacement of sub main wiring drawing in and including concealed PVC conduit not less than 25mm dia medium grade with PVC cable 04 Sqmm nominal area 2 run single core PVC insulated unsheathed cable with stranded copper conductor incl 04 Sqmm size PVC cable stranded copper conducter as earth continuity wire and connected to earth dolly with proper crimping of thimbles bottle type and all as specified and directed.

S&F in replacement of sub main wiring drawing in and including concealed PVC conduit not less than 25mm dia medium grade with PVC cable 06 Sqmm nominal area 2 run single core PVC insulated unsheathed cable with stranded copper conductor incl 06 Sqmm size PVC cable stranded copper conducter as earth continuity wire and connected to earth dolly with proper crimping of thimbles bottle type and all as specified and directed.

S&F in replacement of sub main wiring drawing in and including concealed PVC conduit not less than 25mm dia medium grade with PVC cable 10 Sqmm nominal area 2 run single core PVC insulated unsheathed cable with stranded copper conductor incl 10 Sqmm size PVC cable stranded copper conducter as earth continuity wire and connected to earth dolly with proper crimping of thimbles bottle type and all as specified and directed.

M&L for earthing in renewal of complete with galvanised steel plate electrode 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron wire of size 4 mm by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl excavation and earth work and disposal of surplus soil incl 40 mm GI tubing light grade and necessary fitting for protection of copper strip incl laying of charcoal dust and common salt, PCC (1:2:4) type B-1 using 20mm graded stone aggregate earth pit with 40x40x6mm MS angle iron frame, RCC cover 40mm thick (1:2:4) type B-0 using 12.5mm graded stone aggregate reinforced with 6 mm dia round bar @ 75mm C/C both ways with MS handle 12mm dia, plastering 15mm thick CM (1:6) internally and upto 150mm below ground level externally, PGI funnel with 20mm dia GI pipe for watering and wire mesh complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test incl testing complete all as specified an directed. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

S&F in renewal of VTPN DB,4 way Vertical type, 440V, 3 phase with rated busbar 250 Amps, double door type , IP-54 protection and mechanical strength IK 09 ,isolated neutral busbar suitable for accomodate MCCB 3/4 pole 415 volts rating upto 250 Amp as a incomer and MCBs as out going , grouted in walls complete all as specified and directed.

S&F in renewal of MCB DB of sheet metal enclosure double door type, single pole and neutral 12 way with 200 Amp rated bus bar 240V and grouted in walls with PCC 1:2:4 type B1 using 20mm graded stone aggregate complete all as specified and directed.

S&F in renewal of MCB DB of sheet metal enclosure double door type, single pole and neutral 8 way with 200 Amp rated bus bar 240V and grouted in walls with PCC 1:2:4 type B1 using 20mm graded stone aggregate complete all as specified and directed.

S&F in renewal of MCB DB of sheet metal enclosure double door type, single pole and neutral 4way with 200 Amp rated bus bar 240V and grouted in walls with PCC 1:2:4 type B1 using 20mm graded stone aggregate complete all as specified and directed.

S & Fixing in renewal of MCCB DPX 160 thermal magnetic of 63 Amps 3 pole 16 KA, 415 Volts 50 Hz complete including connecting all incoming and outgoing connection by means of suitable size of lugs/thimbles all as specified and directed.

S & Fixing in renewal of MCB SP 6 to 32 Amps, 240V 'C' Series 10 KA. complete all as specified and directed.

S & Fixing in renewal of MCB DP 40 to 63 Amp 240 Volts 'C' series 10 KA. complete all as specified and directed.

Supply and fix in renewal of LED street light 45 W IP 66, New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Device including GI bracket made by 40mm GI pipe light grade bent to shape of length up to 1.5 mtrs and with clamps ,nut bolts grouting on wall and complete all as specified and directed.

M/S SINGH ELECTRIC CO (BID ID -3206098)

J P CONTRACTORS AND SUPPLIERS (BID ID -3201837)

aman construction & general suppliers (BID ID -3198443)

Balaji Associate (BID ID -3202259)

sumesh furniture (BID ID -3202351)

GIRENDRA SINGH AND CO (BID ID -3202116)