GE/CHM-28/2020-2021 SPECIAL REPAIR TO BLDG NO P-810 AND OTHER SANCTIONED WORK UNDER AGE B/R-III AT CHANDIMANDIR

Amount

Demolition of brick work, stone/ boulder masonry and built in cement mortar including all quoins arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles all as specified & directed by Engineer-in-charge.

Dismantling stone slab & tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar all as specified & directed by Engineer-in-charge.

Demolition of cement concrete unreinforced in ground floor or any floor level, terrazo flooring, kota stone, granite flooring, tiles flooring and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed by Engineer-in-charge.

Demolition of cement concrete unreinforced in ground floor or any floor level, terrazo flooring, kota stone, granite flooring, tiles flooring and pavings exceeding 15cm thickness ( above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as specified.

Demolition of reinforced cement concrete, reinforcement cut as required to facilitate, of any description as in parapet, roof wall, slab, chajjas, shelves and similar work in any position not otherwise specifically provided for, complete all as specified and directed.

Desilting the drains, removal of mud, removing the grass, vegetation, shrubs etc from drain and removing the excavated soil to a distance exc 250 metre and n.exc 500 metre and depositing where difrected at a level not exceeding 1.5 metre above the starting point omplete all as specified & directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc, laying of pipes, cables, poles, stay etc and getting out in hard and dense soil,l all as specified & directed by Engineer-in-Charge.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Excavating in post holes (or similar holes) in hard and dense soil, each not exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm, watering, and removing surplus soil to a distance n.exc 50 Mtr and making good surface complete all as specified & directed by Engineer-in-charge.

Material and labour for sand filling under floor or in foundation average thickness 40mm including watering and consolidationcomplete all as specified and directed.

Removal excavated soil to a distance exceeding 1000 m and upto distance of 1.5 km and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-Charge.

Material and labour for Hard core of broken stone or boulders of gauge of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

Material and labour for Ready Mix Concrete(low density thermal insulative concrete of density 1200 kg/Cum) grade, 1:2:4 Type B-1 obtained from plant approved with MES as in roofs, terraces, sunken and other locations as per site requirements complete all as specified and directed (reinforcement shall be measured and paid for separately) complete all as specified.

Material and labour for plain cement concrete 1:7:12 type F-2 using 40mm graded brick aggregate as in sunken floor filling and mass concrete, including demolition of old lime concrete and complete removal as required, complete all as specified & directed.

Material and labour for plain cement concrete 1:3:6, nominal mix, type C-2 ,using 40 mm graded stone aggregate as in foundation, filling and mass concrete, all as specified & directed.

Material and labour for plain cement concrete 1:4:8, nominal mix, type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete, all as specified & directed.

Material and labour for cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate as in surface channels and drains etc like including necessary forms/ moulds complete all as specified & directed by Engineer-in-charge.

Material and labour for plain cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in roof kerbs or mud stops rounded or chamfered on edges, complete all as specified & directed.

Material and labour for plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straigth or curved) complete all as specified & directed by Engineer-in-charge. - (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Material and labour for reinforced cement concrete 1:2:4, nominal mix, type B-1 using 20mm graded crushed stone aggregate as in Chajja and similar works, all as specified. Note : Reinforcement and form work shall be measured and paid separately

Supply only Integral waterproofing compound,ISI marked, all as specified. Make Pidiproof LW ( Dr Fixit) or equivalent as approved by GE.

Material and labour for brick work with sub class ‘B’ bricks of class designation 7.5 all as per IS-1077-1992 (minimum compressive strength of brick 75 kg / Sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:4 complete as in roof, parapet ,walls, manholes, drains as per site requirement all as specified & directed.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth complete all as specified & directed by Engineer-in-charge.

Supply and fixing solid PVC frame having profile 75mm x 50m , single rebate, made out of solid PVC foam with homogenous fine cellular structure having density 750, smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

Material and labour for form work to, chullah hoods, chajjas, troughs and similar items including edges and similar items including edges for fair finished surface of concrete flat complete all as specified and directed.

Supply and fixing glazed and gauged skelton shutter (Factory made) 35mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated, complete all as specified & directed.

Supply and fixing for 35mm thick second class hard wood factory made plain, framed, panelled shutters (Two panels), with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and Style as per IS:1003 (Part-1), kiln seasoned and chemically pressure treated all as specified & directed by Engineer-in-charge.

Taking down chowkhats or frames (without taking of shutters from the frames) area not exceeding 1.5 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down chowkhats or frames (without taking of shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1.00Sqm but not exceeding 2.00Sqm each complete all as specified & directed by Engineer-in-charge.

Supply and fixing factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

Material and labour for 150mm aluminum anodized barrel tower bolts (ISI Marked) of extruded section, complete all as specifie

Supply and fixing for aluminium, anodized barrel tower bolts (ISI Marked) of extruded section and fixed, 200mm long, dia of bolt not less than 10 mm,complete all as specified.

Supply and fixing Mild steel sliding door bolts (ISI Marked), 250mm long plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, all as specified & directed by Engineer-in-charge.

Supply and fixing 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified & directed by Engineer-in-charge.

Supply and fixing for 150mm size aluminium handle (ISI Marked), cast type, anodised complete all as specified & directed by Engineer-in-charge.

Supply and fixing for aluminium alloy wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, all as specified & directed by Engineer-in-charge.

Supply and fixing for framed work such as grills, gratings, etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings, frame work of water tanks and similar work confirming to Fe-290 grade E-165 complete all as specified & directed by Engineer-in-charge.

Supply and fixing for mild steel flats as in wind ties, plate washers and silmilar small articles confirming to Fe-290 Gde- E-165 complete all as specified & directed by Engineer-in-charge.

Material and labour for mild steel TMT bars 10mm dia & over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.

Material and labour for mild steel TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hoping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

Supply and fixing for Steel work in tubular trusses and tubular posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 t complete all as specified & directed by Engineer-in-charge.

Supply and fixing steel windows , ventilator fixed type with glazing bars, complete all as specified & directed.

Supply and fixing in repair factory made steel windows (Box type) with side hung shutters ,with glazing bars, dovetailed or welded including hinges, steel handles, steel peg stays etc complete all as specified & shown in drawings.

Supply and fixing in repair factory made steel windows (Box type) with side hung shutters ,without glazing bars, dovetailed or welded including hinges, steel handles, steel peg stays etc, complete all as specified & shown in drawings.

Supply and fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc complete all as specified & directed by Engineer-in-charge.

Material and labour 15mm to 18mm thick granite slab (of any type & shade as approved), width and length as ordered by Engr- in- Charge in one piece, best quality machine cut to be fixed steps, jambs, pillars, window-cills, cooking platforms and like and jointed with gray cement slurry and pointed in white cement mixed with marble dust (1:2) with admixture of pigment to match the shade of slab, rubbing and granite polishing,over screed bed 15mm thick in cement mortar 1:4including cutting / rounding of edges where requried complete all as specified and directed.

Material and labour for machine cut Kota Stone Slab flooring, 15 to 18mm thick, best quality (minimum size 58cm x 58cm) over and including cement screed bed 20mm thick in cement mortar 1:6, laid and jointed with grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab, complete all as specified and directed.

Material and labour for 25mm thick cement concrete type B-0, 1:2:4 (using 12.50mm graded crushed stone aggregate) as in sub base finishing even and fair to receive to top layer complete all as specified & directed.

Material and labour for glazed ceramic coloured tiles of size 350mmx250mmx7mm or 300mmx450mmx7mm thick on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick backing coat in CM (1:4) all as specified and directed by Engineer-in-charge.

Material and labour for non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, superior quality as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in CM (1:6) complete all as specified & directed by Engineer-in-charge.

Supply and fixing 60mm thick, factory made machine pressed precast concrete interlocking paver block, with grey cement and no pigment, any shape and size confirming to IS 15658-2006 of M-35 grade, joints filled with sand complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete all as specified and directed.

Material and labour for 15mm thick rendering cement plaster in cement and sand mortar 1:4 over brick or concrete surfaces finished fair and even complete all as specified and directed

Material and labour for 15mm thick rendering cement plaster in Cement and Sand mortar 1:6 over brick or concrete surfaces of wall , finished even and fair complete all as specified and directed

Material and labour for rendering 15mm thick plaster in cement mortar 1:3 mixed on brick wall or on concrete surfaces including dubbing coat if required on internal and external faces of parapet on roof top, RCC facia, RCC parapet wall, cornices, ceiling and finishing the surface even and smooth without using extra cement at height exceeding 6 metre but not exceeding 12 metre and applying 2 Coats cement base paint over a coat of white wash including taking down old plaster and removal of debris upto a distance of 1.50KM and providing necessary form work and scaffolding as per site requirement and carriage of all material all as specified and directed by Engineer-in-charge.

Material and labour for rendering 20mm thick plaster in two layers of 10mm each in cement mortar 1:4 mixed with WPC on fair faces of brick wall or on concrete surfaces or on roof and finishing the surface even and fair without using extra cement all as specified and directed by Engineer-in-charge. Note :- WPC will be measured & paid seperately as supply only).

Roughening surface of old concrete floor by picking, seeping clean and washing down with water to remove dust etc and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm complete all as specified and directed.

Taking down cement plaster from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete all as specified and directed and removing rubbish etc. at the places out side the premises complete all as specified and directed.

Supply and fixing for GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste, fixed in repairs in patches n exc 5 sq. m each, including taking down old and jointing new to old as required all as specified and directed.

Material and labour for preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

Material and labour for three coats of white wash on plastered or unplastered ceiling surfaces including preparation of new surfaces complete all as specified and directed

Supply and fixing for 3mm thick, sheet glass ordinary quality and glazing with oil putty or beading in squares not exceeding 0.50 sqm in each panes complete all as specified & directed by Engineer-in-charge.

Supply and fixing 4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

Hacking out old broken glasses (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified & directed by Engineer-in-charge.

Material and labour for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

Material and labour for preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

Cutting and screwing existing steel water tubing 15/20/25 mm bore for addition /alteration required for connections to water coolers etc complete all as specified and directed.

Supply and fixing bib taps, 15mm bore, long body, fancy type with wall flange, chromium plated, ,cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repair, all as specified and directed.

Supply and fixing for mild steel galvanised iron water tubing 15mm bore with screwed & socket joints, medium grade, with and including all fittings, such as sockets, Bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Supply and fixing for mild steel galvanised iron water tubing 20mm bore with screwed & socket joints, medium grade, with and including all fittings, such as sockets, Bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store of 15 mm bore complete all as directed by Engineer-in-charge.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store of 20mm bore complete all as directed by Engineer-in-charge.

Dismantling water tanks of capacity exceeding 500 litres n exc 1000 litres and removing to store complete, all as specified and directed.

Supply and fixing in repair 1000ltrs capacity rotational moulded polythene water storage tanks ,white coloured, double layered (Cylinderically vertical with closed top) hoisted and fixed in postion including fixing arrangement for inlet, outlet, over flow and vent pipe of standard size complete including dismantling of existing water tanks and removing from site all as specified in SSR Part-I and all as directed by Engineer-in-charge.

Supply and fixing in repair, stop valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 20mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

Supply and fixing , stop valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions complete all as specified & directed by Engineer-in-charge.

Supply and fixing in repair, angular stop valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions complete all as specified & directed by Engineer-in-charge.

Supply and fixing for Stop valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) , screwed down ,high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Supply and fixing ball valves high pressure of PTMT with epoxy coated Aluminium rod &high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) for 20mm bore pipe, fixed as in repairs complete all as specified and directed.

Supply and fixing towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms), complete all as specified and directed.

Supply and fixing for PVC connections 450mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

Supply and fixing for PVC connections 600mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers, water coolers etc complete all as specified & directed by Engineer-in-charge.

Supply and fixing PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, complete all as specified and directed

Supply and fixing 110mm bore PVC (SWR) bends any radius, complete all as specified and directed

Material and labour for cast iron nahani trap 100mm dia with grating including jointing to waste pipe with run led jointed and seting in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Supply and fixing for 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia, as in repairs complete all as specified & directed by Engineer-in-charge.

Supply and fixing in repair for vitreous china wash hand basin white, flat back of size 550 x 400 mm white including waste fittings, brass chromium plated coupling, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

Material and labour for Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with Cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of PCC (1:2:4), type B-I using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc and making good to floors to match existing, in repair, all as specified. Make: Cat Part No. 2071 of 'Cera' or equivalent makes mentioned in Appx 'C'

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar in and including demoliton of 80mm thick mud phuska as in roof of any thickness incl plastering and leeping etc (wheher full thickness removed or only a part therof) with and including removal of any existing treatment and removal of all debries / surplus material and soil etc to a distance of 1.5 Km complete all as specified & directed.

Material and labour for cement concrte tiles 250 x 250 x 22mm thick, machine pressed, set jointed and pointed with grey cement over roof over and including 15mm thick screed in cement mortar 1:4 complete all as specified and directed.

Water proofing treatment to SUNKEN PORTION and adjoining walls of kitech. WC, Bath & Toilet etc. : 15 mm plaster in cement mortar (1:3) after roughning and cleaning the surface mixed with WP compound as per manufacturer's instructions shall be provided on sunken portion while the concrete is green :- (a) Apply cement slurry to the surface @ 0.488 kg / Sq. m of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.253 kg/Sq. m and the surface will be allowed to air cure for 4 hours. (b) Apply another layer of cement slurry @ 0.242 kg/Sq. m of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.126 Kg/Sq. m and the surface will be allowed to air cure for 4 hours. (c) Curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Paste one layer of 3mm thick APP membranne with bitumen by torch application to the treated sunken surface. (e) Joints/Traps/WC/soil pipes shall be properly sealed with approved sealing compound of make mentioned as specified in Appx 'B'. (f) Testing of all traps & Joints shall be done after sealing & before filling of sunken slab

Cutting openings, through brick walls in round shape , for 300mm dia exhaust fan and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required including finishing and making good matching the disturbed surface and removing surplus unserviceable bricks, hard-core, etc..from site and rubbish not exc. 50m complete all as specified & directed by Engineer-in-charge.

Supply and fixing metallic body exhaust fan 300mm sweep, 240 volt, 50 Hz, with louvers heavy duty, 900 RPM, single phase including making connection with suitable size three core cable from celing rose to fan complete all as specified and directed. MAKE : Havell's Cat Part No Turboforce FHEHDSPDB129 and equivalent in BAJAJ/Crompton/Khaitan

Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete

Material and labour for point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase &neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly including new cast iron sunken boxes duly painted with two coat of anticorrosive paint over a coat of red oxide primer on surface in touch with wall and synthetic enamel paint over a coat of red oxide on other side covered with 3mm thick plastic laminated sheet, comprising of One light /bell/buzzer/ fan point controlled by one switch or one fan point controlled by one switch &fan regulator in and including rigid non metallic PVC heavy duty CONCEALED CONDUIT complete as directed Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account.

All as per serial item 98 herein before but for socket outlet 3 pin 6 Amps on same board complete all as specified and directed

All as per serial item 98 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 98 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Supply & Fixing for MCB ,SP , 240 volt, 40Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engineer-in-charge. Make :-Havells Cat Part DHMGCSPF040. or equivalent makes mentioned in Appx 'C'.

Taking down existing Ceiling fan or exhaust fan carefully , kept safely and refixing the same , all as specified.

Supply and fixing MCB SPN 240 volt 63Amps 10 KA, 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engineer-in-charge. Make :- Havells Cat No. DHMGCSNF063 or equivalent makes mentioned in Appx 'C'.

Supply & Fixing for MCB ,SP , 240 volt, 63Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engineer-in-charge. Make :-Haells Cat DHMGCSPF063 or equivalent makes mentioned in Appx 'C'.

Supply and fixing sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 10Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 10 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through and including PVC concealed conduit 32mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good, after taking out old unserviceable sub main wiring complete all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 10 sqmm and one single core of 10 sqmm cable along with PVC conduit shall be considered as 1 running metre.

Supply and fixing sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 6 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 6 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through and including PVC concealed conduit 20mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good, after taking out old unserviceable sub main wiring complete all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 6 sqmm and one single core of 6 sqmm cable along with PVC conduit shall be considered as 1 running metre.

Supply & Fixing for MCB ,SPN , 240 volt, 40Amps 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engineer-in-charge. Make :-Havells Cat NoDHMGCSNF040 or equivalent makes mentioned in Appx 'C'.

Supply and installation of desert cooler with outer body made out of PGI (Plain Gaivanised iron) sheet not less than 1.20mm thickness for fixed part, thickness of PGI sheet for shutter not less than 0.80mm thick alongwith three Nos for three side cellulose / honey comb colling pads, front grill made of PGI sheet with minimum weight 2.80Kgs, overall outer size not less than 66cm x 66cm x 99cm (height), electric driven copper wounded fan motor and submersible pump for required flow of water (single phase) having nominal airflow capacity 4000 cum per hour including provn of stand frame made out of 40x40x5mm thick MS angle iron of size required at site along with welding and two coat of synthetic enamel black paint over a coat of red oxide complete all as specified and as directed. Make of motor and submersible pump : Khaitan /Bajaj /Crompton

Supply and fixing for sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 2.5 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 2.5 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC in and including concealed conduit 20mm size(minimum size) including cutting chases in walls for PVC concealed conduit and making good to match with existing surface complete all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 2.5 sqmm and one single core of 2.5 sqmm cable shall be considered as 1 running metre. (ii) Color code shall be Red for phase, black for neutral and green for earth

Supply and fixing switch piano, flush type, 15 amps, 230 volts, single pole, one way (ISI marked) and shuttered socket out let, 3 Pin, 16 Amp, 230 volts piano flush type and mounted on and independent sunken box and provision of 3mm thick plastic laminated sheet, , complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces to match the original and nothing extra shall be paid on this account.

Supply and installed voltage stabilizer automatic digital display type, single phase naturally air cooled indoor type & designed for input variation between 170V to 250 Volt with output voltage stabilized at 230 Volt + 2.5% ocapacity 3.0 KVA complete all as specified and directed.

Supply only Indoor decorative extruded aluminium anodised housing /CRCA sheet steel coated housing (suitably coated to improve resistance against corrosion) LED batten type luminaire (LED batten shall be prewired box type) retrofit solution with and including replaceable retrofit cool day warm white LED tube rod with well designed aluminium heat sink /aluminium housing for excellent heat dissipation; 4 feet (appx) size, high efficiency electronic driver, system wattage not more than 20 watt (lumen output not less than 2000 lumen), power factor more than 0.9, with surge protection device minimum 2KV, colour temperature not less than 5700K, LED driver with constant output voltage and current at input voltage of 140 Volt to 285 Volt AC at 50 Hz, CRI more than 80, glarefree, 0 UV radiation light fitting with wall mounting arrangement and making connections with PVC insulated copper conductor 3 core cable of 0.5 sqmm all as specified including taking down old u/s tube light fitting complete all as specified and directed.

Supply, Installation, testing and commissioning of water cooler partially stainless steel body, electric driven, single phase having storage capacity of 60 litre and nominal cooling capacity of 120 litres per hour complete all as specified & directed by Engineer-in-charge. (Make :- Voltas, Usha, Blue Star as approved by GE.)

Supply, Installation, testing and commissioning of water cooler partially stainless steel body, electric driven, single phase having storage capacity of 40 litre and nominal cooling capacity of 80 litres per hour complete all as specified & directed by Engineer-in-charge. (Make :- Voltas, Usha, Blue Star as approved by GE.)

Supply and fixing MCCB, 100 Amps, four pole,3 phase ,25 KA, 415 volt with adjustable thermal and maganetic release complete all as specified and directed by Engineer-in- Charge. (Make:- Cat ParNo IHLASDCF0100 of Havell's or equivalent makes mentioned in Appx 'C' as approved by GE).

Supply and fixing for VTPN distribution board double door flush mounting with provisions for MCCBs incomer upto 100to 125Amps & outgoing 4 way having IP 54 protection complete all as directed by Engineer-in-charge.(Make :- Havells Cat part No:-DHDPTVODRW04 or equivalent makes mentioned in Appx 'C').

Disconnecting and taking down carefully copper/aluminium sub main wiring complete, including existing batten/surface conduit etc., removing materials and making good disturbed surfaces of wall, floors, etc. complete all as specified.

Supply and fixing sheet metal enclosure DB's 240 Volts, IP-43, suitable for mounting MCB's, SPN, 12 way double door with 200 Amps rated copper bus bar and blank plate as required complete all as directed by Engineer-in-charge.(Make :- Havells Cat Part No. DHDPSHODRW12 or equivalent makes mentioned in Appx 'B').

Supply & Fixing for MCB ,SPN , 240 volt,06- 32Amps 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engineer-in-charge. Make :-Havells Cat No DHMGCSNF06-032 or equivalent makes mentioned in Appx 'C'.

Supply & Fixing for switch piano, flush type, 5 amps, 230 volts, single pole, one way (ISI marked) complete all as directed by Engineer-in-charge

Supply & Fixing for switch piano, flush type, 15 amps, 230 volts, single pole, one way (ISI marked) complete all as directed by Engineer-in-charge

Supply & Fixing for sockets outlet multipurpose 2 in 1 pin, 5 and 15 Amps flush type ISI marked all as specified and directed by Engineer-in-charge

Supply & Fixing for sockets outlet multipurpose 2 in 1, 5 Amps flush type all as specified and directed by Engineer-in-charge

Supply & Fixing for ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

Supply and fixing blanking plate one module complete all as specified and directed

Supply and fixing for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting including 9 watt LED lamp complete all as specified and directed.

Material & labour for earthing complete with galvanized steel earth plate electrode size 600x600x6.0mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanized earth lead 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized including Gl protection pipe light grade 15mm bore connected to main earth wire on pole light grade 15mm bore connected to main earth wire on pole or control board or main switch and Gl pipe medium grade 20mm bore for watering funnel with wire mesh CI cover with frame, PCC chamber pit with PCC 1:2:4 type B-1 20 mm graded stone aggregate excavation and earth work all as shown in electrical plate No 3 of MES Schedule part I of 2009 connected to earthing test point indicated including testing on completion all specified and directed. Note : The unit rate including for protection pipe and Gl earth wire 4.00 mm dia from top to earth plate up to 7.5 meter

M.P. Builders

M/s Krishan Aggarwal

Vasudeva Trading Co.

VRIDHI ENTERPRISES