ADDN/ ALTN TO STUDENT FACILITY IN OFFR MESS, PROVISION OF TOILET NEAR SIGNAL EXCHANGE AND SPECIAL REPAIR TO BLDG NO. 327 AT CME, PUNE

Amount

Dismantling wall and ceiling boards (fibre, pulp, insulation boards/ slabs/ blankets) any thickness, including cover fillets all as specified and directed

M&L for false ceiling of POP gypsum board of size 600mx600mmx12mm thick and frame made out of MSGI BPS grade, angle 24mmx24mmx0.43mm, T section 24mmx25mmx0.30mm and main runner T section 24mmx38mmx0.35mm complete with angle fixed to wall with rawl plug 100mm long of maximum 600mm c/c, hanging with 2.50 / 3.00mm dia GI wire suspenders fixed to ceiling with 80mm long rawl plug providing 1 No. per sqm complete including designer cornice at edge and anywhere else as required, and suitable provision for electric fittings and painting with two coats of OBD over one coat of primer after preparation of surfaces complete including dismantling of old ceiling of any description and any size any height etc complete all as per manufacture instruction and all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed.

Demolition of cement concrete (unreinforced ) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in subbase all as specified and directed.

M&L vitrified ceramic coloured tiles (dark shade) 10mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as spcd and directed.

All as per item No 06 above, on vertical surfaces such as skirting and including 10mm thick backing coat in cement mortar 1:3 complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm and n.exc 4 sqm complete all as specified and directed.

Taking down cement plaster any description from roof slab, stone wall, brick wall parapets including raking out joints, hacking for key and scrubbing down with water etc (for roof treatment) complete all as specified.

M&L rendering 15mm thick on stone masonry surfaces in CM 1:6 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying 3mm thick Birla wall care putty and two coats of oil bound distemper over one coat primer on walls complete all as specified and directed.

M&L preparing newly plastered surfaces of ceiling and applying 3mm thick Birla wall care putty and two coats of oil bound distemper over one coat primer on ceiling complete all as specified and directed.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses complete all as specified and directed.

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L 18-20mm thick Marble (of any type) and any shade (except white & black) in kitchen platform machine cut and mirror polish bedded over cement mortar screed 15mm thick 1:4 and jointed in grey cement slurry and pointed in white cement with admixture of pigment to match the shade of marble stone including grinding etc complete all as speficied and directed.

Rounding to edges of stone slabs, such as in steps, cooking platform, and other similar situation complete all as specified and directed.

S&F First class hard wood plain, solid, straight chowkats or frames in cup board, rough framed, rebated on the solid, rounded or chamfered put together with glue, pinned at joints all as specified and directed.

S&F 18/19mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face as in cup board shutters excluding external teak wood lipping, 6mm thick fixed with nails all as specified and directed.

Extra over rates of block board or veneered particle board for external teak wood 18/19mm lipping 6mm thick fixed with nails all as specified and directed.

M&L 18/19mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice lamination fixed with screws to timber frame including dismantling existing board complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) in 30mm complete all as specified and directed.

S&F ball catches with 8mm dia steel ball and brass body and skating plates for cup board shutters etc all as specified and directed.

M&L aluminium anodised barrel tower bolts, stove enamelled black, with bright bolt and fixed of size 75 mm complete all as specified and directed.

S&F 75 mm size hasp and staple, aluminium anodised, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws all as specified and directed.

S&F 75 mm size aluminium anodised pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F 12mm thick sheet glass, ordinary quality fixed in any position exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for grinding, polishing and rounding of edges of glass exc 4mm but n exc 8mm thick, any type and in any position etc complete all as spcd and directed

S&F stainless steel / Brass chromium plated brackets L shape/ C shape for fixing of glass corners/ glass for decorative purpose etc as directed by EIC

M&L for two coat of synthetic enamel paint over wooden surfaces including preparation of new surfaces over 10cm width or girth and filler coat with grey filler or liquid wood filler, transparant and bringing forward surfaces to smooth even and finish all as specified and directed by the Engineer-in-Charge.

S&F stainless steel / brass chromium plated designer liquor/champagne glass holder fixed to wall / ceiling, made up of SS 304 Gde (PB 82 rope twisted) pipes dia ranging 25mm to 40mm, SS bars 304 Gde (satin SS) dia ranging 6mm to 16mm, SS 304 Gde (Satin SS 84) flats and including necessary hangers and fiddle rails for glass shelf/ decorative design of polished SS/ brass chromium plated material and using necessary joints/ modular elbows and bends / flanges / brackets / 3 way corners / couple set / rings / spigot / studs / pipe bases / ballusters etc as per direction of EIC Note : Design will be provided by EIC

S&F aluminium colour powder coated anodised door and shutter single or double leaf glazed/pre laminated board exterior quality partly glazed/ pre laminated board exterior quality party glazed panels fabricated including aluminium anodised beading rubber and packing materials and shall be drilling in existing wall and thrust bolt suitable size complete comprising the following:- (a) Aluminium colour anidised door frame section 101.60x44.45x1.93 mm fixed as per spd (b) Aluminium colour anodised vertical section in shutter 85x44.45x2 mm as per spd. (c) Aluminium colour anodised Top & stile shutter section 95.25x44.45x2.00 mm as per spd. (d) Aluminium colour anodised handle 02 Nos in each shutter 200 mm long as spd. (e) Aluminium colour anodised middle lock rail/bottom rail section 150x44.2.65mm cat No.20002. Make-Jindal (f) Floor spring Make-Sandhu, (g) Six lever mortice lock brass Make : Godrej/Classic on in each door (h) 12 mm thick particlular board (pre laminated both face) exterior grade ISI Marked (j) Tinted glass/Plain glass(Colour) 5mm thick Make : Saint gobain/ modiguard (k) Floor spring , Make Sandu Note : If ground requirement for full glass or full Panel contractor should provide as per direction of Engr-in-Charge.

Excavating in trenches n exc 1.5m wide and not exc 1.5m in depth for foundation and getting out in soft/ loose soil all as specified and directed.

M&L cement concrete type D-2,1:4:8 (40mm graded stone aggt) as in foundation filling and mass concrete all as specified and directed.

M&L Damp proof course 40mm thick using cement concrete type B0 1:2:4 to horizontal or vertical surfaces including necessary formwork complete all as specified

Supply only integral water proofing compound all as specified and directed.

M&L for precast cement solid block masonry 1:3:6 type C-1 wall exceeding 10 cm in width and built in cement mortar 1:6 all as specified and directed.

M & L for moorum/red bajri filling in floors or pavings, fdns laid in layers not exc 15 cm thick spread levelled & rammed incl watering all as specified and directed.

M&L hardcore of guage exc 63 mm deposited ,spread and levelled in layers n.exc 15 cm thick watered and rammed to a true surface all as specified and directed.

Returning , filling in, includidng spreading , levelling , watering and well ramming in layers not exc 25 cm in hard/ dense soil complete all as specified and directed.

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M & L Rendering 10mm thick on fair face of brick or concrete surfaces in CM 1:6 finished even & smooth without using extra cement complete all as specified and directed.

M & L Rendering 15mm thick other than fair face of brick or concrete surface masonry in CM 1:4 finished surface even and fair without using extra cement complete all as specified and directed.

M & L Rendering 5mm thick in CM (1:3)on ceiling surface finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces and applying three coats of white wash on walls complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces and applying three coats of white wash on ceiling all as specified and directed.

M&L for preparation of surface of wall and applying two coat of cement based paint on wall all as specified and directed.

M&L 75mm thick cement concrete type C2,1:3:6 (40mm graded stone aggt) as in plinth protection finished even and smooth using extra cement including use and waste of formwork all as specified and directed.

M&L non skid ceramic tiles 400x400mm (Square/ rectangular) are of each tile area exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM(1:6) complete all as specified & as directed.

M & L RCC (Nominal Mix) type B1, 1:2:4 (20 mm graded stone aggregete) as in slab supported on walls complete all as specified and directed.

M & L RCC (Nominal Mix) type B1, 1:2:4 (20 mm graded stone aggregete) as in lintel and roof beamcomplete all as specified and directed.

M & L for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with MS wire (annealed) not less than 0.9mm dia for securing with clips complete all as specified and directed.

-Ditto- all as per sl item No. 52 above, but 5mm dia and over upto and incl 10mm dia in stirrups spacers and binders.

M & L for form works to soffits of suspended slab etc. n. exc. 20cm thick flat fair finished surfaces complete all as specified and directed.

M & L for form works to edges of concrete flat exc. 5 n. exc. 10 cm in width and fair finished surfaces complete all as specified and directed.

M & L for form works to sides of roof beams and lintels etc flat fair finished surfaces complete all as specified and directed.

S&F bands straps, hold fast, wind tie & similar articles conforming to Fe-290 gde E-165 all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube etc all as specified and as directed.

S & F factory made solid PVC moulded door shutter, 30 mm thick with 4 raised panel design with 2 mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core complete all as specified and as directed.

Supply and fixing aluminium anodised butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified and directed.

S & F 125mm aluminium handles, cast type anodised all as specified and directed.

S & F 200 mm long Aluminium anodosied , barrel tower bolt of extruded section all as specified and directed.

Supply and fix 15 mm bore medium grade galvanised steel tubing with all fitting laid in trench complete all as specified and directed.

All as per item No. 63 above, but 20mm bore

Supply and fix 15mm bore bib taps, cast copper alloy chromium plated fancy type with capston head handle screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

Supply and fixing 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed.

Supply and fix 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches all as specified and directed.

All as per item No. 67 above, but 75 mm bore

Supply and fixing vitreous china wash basin, white, flat back, size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste coupling , waste pipe complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern) white (including fixing bolts, flushing cistern and flush pipe) including provision of flush pipe, plastic seat cover for pedestal pan and cp health faucet including two way angle cock complete all as specified and directed

Supply and fixing 10 ltr capacity UPVC valveless , syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S & F tubular CP towel rail 20 mm dia D type 60 cm long between flanges all as specified and directed.

M & L for SGSW drain pipes 150 mm bore grade 'A' laid in trenches and jointed in CM (1:1) all as specified and as directed.

M & L cement concrete(1:4:8) type D2 using 40mm graded mechanically crushed stone aggreget as in bed to 150mm bore drain pipe haunching against the sides of pipes after they are laid and tested thickness of bed shall be 100 mm complete all as specified and as directed.

M &L for precast RCC (1 : 2 :4) type B1 using 20mm graded mechanically crushed stone aggregate as in landing cover slab for manholes septic tank set in CM (1:6) complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends with oval accesse door with rubber ring joints fixed as required complete all as specified. (Make : Finolex, Diplast, Supreme)

S&F 110mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified. (Make : Finolex, Diplast, Supreme)

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement incl necessary PCC & form work as required complete all as specified. (Make : Finolex, Diplast, Supreme)

S&F 110mm dia PVC (SWR) bends with rubber ring joints fixed as required complete all as specified. (Make : Finolex, Diplast, Supreme)

S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed.

S&F mild steel works in window guard bar etc and similar articles conforming to Fe-290 Gde E-105 all as specified and directed.

M&L prepapration of new or previously untreated steel surfaces of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer comlplete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm all as specified and directed.

S & F 3 mm thick figured glass,pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane all as specified and directed.

S & F 15mm fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or with out lettered "hot or Cold" with long screwed shanks and fly nuts screrwed for iron pipe complete all as specified and directed.

S & F 500 ltr capacity rotational moulded polythene water storage tanks (clyndrical vertical with closed top) hoisted and fixed in position all as spd in SSR Part I. (Make:- Sintex, Diplast, Aquaplus)

S & F 20 mm bore stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe 20mm all as specified and directed.

S & F 20 mm bore ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipe 20mm all as specified and directed.

M & L for point wiring any length using approved colour coding as per IS, with stranded copper conductor 1.5 sq. mm (nominal area), single core, PVC insulated and unsheathed stranded cable 1100 volts grade, (FR) ISI-694 marked in and including heavy duty, PVC conduit including all accessories etc, heavy duty ISI marked, with mild steel sunken boxes with earth dolly duly concealed in wall, painted with two coats of anti corrosive paint over a coat of red oxide primer, internally, covered with plastic laminated sheet suitable for switches, including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly, complete all as specified for the following :-

One light/ fan point controlled by one switch and regulator

Socket outlet, three pin, 5 Amps on independent board

Socket outlet, three pin, 5 Amps on the same board

All as per item no. 90 above, but with stranded copper conductor 2.5 Sq. mm (nominal area) including PVC insulated stranded copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

S & F modular switch one way and 6 Amps, 1 module, 230 volt complete all as specified and directed.

S & F modular switch one way and 16 Amps, 1 module, 230 volt complete all as specified and directed.

S & F modular socket outlet multipurpose having provision fo 3 pin, 6 Amps and 2 pin, 6 Amps, combines 2 module complete all as specified and directed.

S & F modular socket outlet multipurpose having provision fo 3 pin, 16 Amps and 3 pin, 6 Amps, combines 2 module complete all as specified and directed.

Supply & fix recess mounted LED downlighter elegantly designed die-cast AI heat shrink for efficeient heat dissipation and separate replaceable electronic driver of ceiling cutout dia 180mm, height 68mm of Cat part No : ENDURANEODLR25WLED840S OF HAVELLS all as directed by Engr-in-Charge

Supply & fix flexible LED strip of 5 mtr length used brightness SMD LED as the light source for indoor application only. It is highly suitable for cove-lighting, decorative, decorative lighting etc of Cat part No. FLEXISTRIP5MTRIP2024WLED830S of Havells all as directed by Engr-in-Charge

Supply & fix fusion pendant 1LS E27 D120 BLK of capacity 7.5W LED filament lamp of Cat part No. LHFXAGN1TN1K040 of Havells all as specified and directed by Engr-in-Charge

Supply & fix cylindro with the high power LED, cylindro offrs various luminous intensity levels from 1500-3500 lumens which is the perfect alternate to conventional HD lamps of capacity 15W of Cat part No. CYLINDROTSS15W839S24DWHT of Havells all as specified and directed by Engr-in-Charge

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated cable with stranded copper conductor of size 06 Sq. mm nominal area and drawing in PVC conduit inclduing PVC insulated 6 Sqmm (nominal area) stranded copper conductor earth wire complete. NOTE : Two runs of 6 sqmm cable, one run of 6 sqmm cable and one run PVC conduit will be measured as one unit

Supply & fix VTPN MCCB 125A, DB double door with provision for FP MCB/ isolator /RCCB etc as incommer and SP/TP MCBs as out going double door IP 54 protection complete prewired inclduing Bus bar etc suitable for operation on 415 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and as directed by Engineer-in-Charge. [Make : Indoasian/ Schneider/ Siemens ] for the 4 way TPN, 415 volts

Supply & fixing of MCB four pole rating capacity 40 to 63 Amps, 240 V breaking capacity 9KA C series all as specified and directed.

Supply & fixing of MCCB 125 Amps four pole, 415 volts, 50HZ, 36 KA all as specified and directed.

Supply & fixing of MCB single pole and neutral rating capacity 20 to 40 Amp, 240 V breaking capacity 9KA C series all as specified and directed.

Supply & fixing of MCB single pole rated capacity 5 to 32 A, 240 V breaking capacity 9KA C series all as specified and directed.

Supply & fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps all as specified and directed.

M & L for Earthing complete with galvanized steel plate electrode 60cmx60cmx6mm surrounded by charchoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25 metre below ground level with top edge of the earth plate at depth of not less than 1.50 metre below ground level connected to galvanized iron or steel earth wire, 4mm dia (No. 8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron, earth wire protected by galvanized steel pipe 15 mm dia (Light grade) & connected to main switch or main control board all as shown in electrical plate No. 3 of SSR-2009 Part-I & including necessary excavation and earth work. The rate also include charcoal and salt in alternate layers, 20 mm dia pipe (Light grade) for watering, protection pipe, funnel, wire mesh, PCC chamber in cement concrete (1:3:6) type C-I, 40 mm thick RCC (1:2:4) type B-1 cover and CI frame etc. all as specified and directed.

S & F ceiling roses, surface bakelite suitable for 3 pin 230 volt 50 Hz AC supply complete all as speicified

S & F switch piano, flush type, single pole, one way and 6 Amps, 230 volt complete all as speicified

S & F socket outlet multipurpose having provision for for 3 pin, 6 Amps and 2 pin, 6 Amps, piano flush type complete all as speicified

S & F sub main wiring with approved colour coding as per IS with single core PVC insulated cable with stranded copper conductor of size 04 Sq. mm nominal area and drawing inbto PVC non metalic PVC conduit including PVC insulated 4 Sqmm (nominal area)stranded copper conductor earth wire complete. NOTE : Two runs of 4 sqmm cable, one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit.

Supply and fix surface wall mounted LED batten, extruded aluminium housing provided for effiecient heat dissipation with polycarbonate diffuser and integrated electronic driver for LED tube complete with retrofit LED energy saving recess/ surface mounted luminaries, high efficiency diffuser for soft glare fee ligth of cap[acity 20 watt suitable of oiperation on 230 volt 50 Hz AC supply complete all as specified and as directed by Engineer-in-charge. Make Cat Part No. ENDURALINEARNEOBS20WLED865SPCWH of Havells or equivalent model in Wipro/ HP/ Philips as approved by GE

Supply and fix security light LED fittings 25 watt pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP 65 protection and necessary fixing arrangements i.e. pipe mounting GI bracket bent in shape not exceeding 1.5 mtr in length made out of 40 mm dia GI pipe complete all as specified and directed by Engineer-in-charge. (Make : Havells item decription ENFURACITYLITEPLATSL25WLED757SASYOPC or same type in all respect of wipro/ Bajaj)

Supply and fix exhaust fan AC single phase 230/ 240 volts heavy duty of size 300 mm sweep, 1400 rpm, with louvers and all fixing arrangement such as plywood 18mm thick of suitable size all as specified and directed.

M & L for cement concrete 25 mm thick ,1:2:4 type B-1 (using 20mm graded stone aggregate) as in subbase, finishing even and fait using extra cement complete as specified and directed

M&L Non Skid ceramic colour tiles 7 to 8mm thick (squares /rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 15mm thick screed bed in cement mortar 1:6 Laid and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

M & L for coloured glazed ceramic tiles 350x250x7mm/ 450x350x7mm thick & boarder in vertical surfaces such as skirting , dado etc set & jointed in neat cement slurry & pointed in coloured cement to match fixed including over backing coat 15 mm thick in CM 1:4 all as specified and directed

M&L 20mm thick Granite (of any type) in steps, jamps, pillers, window cills, kitchen platform machine cut and mirror polish bedded over cement mortar sceed 15mm thick 1:6 and jointed in grey cement with admixture of pigment to match the shade of granoite stone including grinding etc complete all as specified and directed.

S & F Bib cock with wall flange complete as specified and directed Make Jaquar

S & F in Angular stop cock with wall flange of 15mm dia capastan head complete as specified and directed , Make Jaquar

S & F in repair Hand shower (Health Faucet) with 1 meter long PVC tube & wall hock, Make Jaquar

S & F in repair Soap dish holder complete as specified and directed by Engr-in-Charge. , Make Jaquar

S & F in repair Toilet paper roll holder with flap complete as specified and directed , Make Jaquar

S & F in repair Glass Shelf 600mm long complete as specified and directed , Make Jaquar

S & F in repair Single Towel Rail 600mm long complete as specified and directed, Make Jaquar

S & F in repair Towel Ring complete as specified and directed , Make Jaquar

S&F in repair viterious china wash basin, white, flat back, size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste coupling and waste pipe complete all as specified and directed. Make Jaquar

S&F in repair viterous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) including provision of flush pipe , plastic seat cover for pedestal pan complete all as specified and directed. Make Jaquar

S&F in repair 10 ltr capacity PVC valveless , syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackeet and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed. Make Jaquar

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete

Raking out joints /pointing to random rubble or polygonal rubble uncoursed or brought upto courses built in cement mortar complete all as specified

M&L raised pointing to random or polygonal rubble , uncoursed or brought upto courses in CM 1:4 complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as specified and directed.

M&L walling random rubble uncoursed , well bonded, bedded and solidly hearted built in CM 1:4 complete all as specified and directed

S & F in repair fancy latch lock for door with all accessories complete all as specified and directed

S & F in repair center hole basin mixer with popup waste system with 450 mm with all connecting accessories complete all as specified and directed by Engineer-in- charge complete as specified and directed , Make Jaquar

S & F in repair wall mixer with hand shower arrangement with connection legs wall flanges and wall bracket for hand shower complete all as specified, Make Jaquar

S&F in repairs loft water storage tank moulded polyethylene of capacity 750 Ltr hoisted and fixed in position including dismantling of existing PVC tank complete all as specified and directed.Make-Sintex

S & F in repair Bib cock 2 in one complete as specified and directed, Make Jaquar

Supply and fix in repair overhead showers 105mm dia complete as specified and directed , Make Jaquar

S&F in repair fancy type curtain rod powder coated 20mm dia (of approved colour and design) all as specified and directed

S & F cast iron floor trap with grating including jointing to waste pipe in run lead, dia of outlet 75mm fixed in repairs complete complete as specified and directed by Engr-in-Charge.

Dismantling CI/AC/PVC (SWR) pipes of any size and any description fixed to wall/laid in trenches including making good disturbed portion of wall floor etc.

S & F 110 mm dia PVC (SWR) bends any radius, provided with access door complete as specified and directed

S & F PVC (SWR) branch pieces, single (single 'Y') equal or unequal, 110 mm bore provided with access door complete as specified and directed

S & F PVC (SWR) junction single (single T) equal or unequal 110mm bore, provided with access door complete as specified and directed

S & F PVC (SWR) branch pieces, single (single Y) equal or unequal, 75 mm bore, provided with access door complete as specified and directed by Engr-in-Charge.

S & F PVC (SWR) junction single (single T) equal or unequal 75mm bore, provided with access door complete as specified and directed by Engr-in-Charge.

S & F 15mm dia steel water tubing medium grade galvanized with and including all fittings such as bend, tees , union etc and fixed complete to walls and ceilings or laid in floors including taking down existing U/s pipe complete all as specified and directed.

S & F 20mm dia steel water tubing medium grade galvanized with and including all fittings such as bend, tees , union etc and fixed complete to walls and ceilings or laid in floors including taking down existing U/s pipe complete all as specified and directed complete as specified and directed

S & F in repairs bathroom cabinet mirror of hard thermosetting plastic of size 400x500mm, fitted with superior quality distortion free 4mm thick mirror complete as specified and directed by Engr-in-Charge. .

M & L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but not exc 20 cm girth complete all as specified and directed complete as specified and directed by Engr-in-Charge.

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x38mm x 0.7mm cross tee of size 24mm x 28mm x 0.7 mm using porpose made members interlocking to each other and with 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction make of GI Grid work : Armstrong/Swastik/Techno Grid and Make E board Gypsum or equivalent approved .

M&L 5mm thick rendering on ceiling surface in CM 1:3 including taking down existing plaster complete all as specified and directed.

M&L 15mm thick cement plastering on stone masonry surfaces in CM (1:4) finishing surfaces even and fair without using extra cement over and including 10mm thick dubbing out on irregular face of wall in CM 1: 4 including taking down existing plastering of any description complete all as specified.

M&L Preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of exterior emulsion paint 100% acrylic (Apex) over a coat of primers with pressure pump & Mechanical Machine as per manufactured instruction complete all specified and directed.

M&L Painting one coat of synthetic enamel paint on steel surface including preparation of old surface of any description, over 10 cm width or girth not otherwise described all as specified and directed by Engineer-in-Charge.

M&L for Preparing old Wood and Wood Based Surfaces of any description, over 100mm width or girth and applying one Coats of Synthetic Enamel Paint (First quality) complete all as specified and as directed.

M&L Preparation of newly plastered or unplastered surfaces on walls and applying two coats of oil bound distemper over a coat of primer inluding chalk complete all as specified and directed.

All as per item No 159 above, but two coats of white wash on ceiling complete all as specified and directed.

Taking down Chowkats or Frames, not exc. 1.50 Sqm Each with Shutters (without Taking Off Shutters from the Frames), complete all as specified and as directed.

Taking down shutters only of size exc 2.00 Sqm

S & F factory made plain framed paneled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as spd.

S & F 30mm thick flush shutter, solid core construction, with block board core and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S & F 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified.

M&L for Preparing New Wood and Wood Based Surfaces of any description, over 100mm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Coat of Pink Primer, complete all as specified and as directed.

S & F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified.

S & F 150mm long Aluminium handles, cast type anodised

S&F 300mm long Aluninium alloy, anodised , sliding door bolt with hasp , staple, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repair 150mm dia double legged door stopper of aluminium alloy with rubber complete all as specified and directed.

S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw.complete all as specified and directed.

S&F in repairs for 50 mm stainless steel Railing interlocking chain of dia 6 to 8 mm thick to steel pipe by hook arrangement as per approved by GE

M&L for complete scraping down of old decorative surface of walls with mecanical tool and steel wire brushes of smoke spots, moulds, moss efflorecent salts including filling of spots with POP/Birla putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer with pressure pump & Mechanical Machine all as specified and directed

M&L for complete removal of existing treatment with Mechanical tools from walls, filling the holes/cavities and platering the surface required, cleaning and preparation of the surfaces and applying two coats of exterior emulsion paint 100% acrylic (Apex) over a coat of primers with pressure pump & Mechanical Machine as per manufactured instruction complete all specified and directed.

M&L machine cut kota stone slab as in flooring /skirting 20-25 mm thick over and including 15mm thick (avg thickness) cement screed in CM 1:6 base, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl cutting , waste, rubbing and polishing (granite finish) etc complete all as specified and directed.

M&L machine cut kota stone slab as in flooring/skirting 20-25mm thick in riser of steps, skirting, dado and pillar inclu 15mm thick (avg thickness) rendering in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl cutting, waste, rubbing and polishing(granite finish) etc complete all as specified and directed.

S & F in repairs brackets powder coated of approved decorative type suitable for fixing curtain rods of 19/20mm dia pipe incl fixing screws, drilling etc as per sample approved by Engr-in-charge all as specified and as directed.

M&L 18/19mm thick Pre-laminated board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination , fixed with screw to timber frame including taking down existing board of any description complete all as specified and directed.

M&L cover fillet (lipping) of tempered hard board 40mm wide, 6mm thick and fixing with screw complete all as specified and directed.

S&F stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, fixing etc, and fixed in repair complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendents regulators, sockets etc revoming materials to store for seperately) and making good disturbed surface of walls, floors etc

Taking down ceiling fans any type/sweep 230 V AC and refixing after cleaning and making connection complete.

M&L for point wiring for light, fan with 1.5 sqmm PVC insulated (red phase and black for neutral) unsheathed, multi stranded coppe conductor 1100 volt grade FRLSH cable in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.5 sqmm green in colour PVC sheathed multistranded copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface/flush type and modular white cover plate with frame all as directed for one light/fan point controlled by on switch.

All as per item No 184 above, but for 5 pin 5 amps socket outlet on same board with other switches

All as per item No 184 above, but for 5 pin 5 amps socket outlet on independent board.

All as per item No 184 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuity for 6 pin 15 amps socket outlet flush type on independent board

S&F Modular socket 6A 2/3 pin combined 2 module

S&F ceiling rose on PVC square blocks, 3 phase PVC/polycarbonate isolated body

S&F angle/batten lamp holder on PVC square blocks, PVC/polycarbonate type with back plate suitable for batten fitting

S&F modular fan regulator electronic rotary stepped increase type 2 module 120W

S&F modular sockets 6A/16A, 2/3 pin combined 2 module

S&F modular switches 2 way 16 amp, 1 moduel

Supply and fixing on two PVC square blocks surface and wall mounted LED batten 20 watt(LED tube light fitting ) extruded aluminium housing provided for efficeint heat dissipation wth plycarbonatge diffuser & integrated electronic driver incl taking down old UNSV one.

Supply and fixing on two PVC square blocks surface and wall monted LED batten 10 watt(LED mirror tube light fitting) extruded aluminium housing provided for efficient heat dissipation with plycarbonate diffuser & integrated electronic diriver incl taking down old UNSV one.

Supply and fixing decorative CITY 3 wall light fixture made up of polycarbonate suitable for 10 watt LED lamp

S&F building security light luminaire LED type fitting 45Watt pressure die cast housing with individual LEDs suitable for 230 volts 50 Hz single phase AC supply IP 65 protection including suitable size GI bracket, medium grade not less than 1m in length bent to shape and fixing on wall with MS clamps and brackets incl taking down old unserviceable light fitting of any type.

M & L Taking down existing LED fitting any type, including cleaning for refixing and refix the same or all as specified and as directed by Engineer-in-charge.

S&F in replacement by flushing to walls MCB distribution board SPN 240 volts 8 way double door with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc

All as per item No 199 above, but SPN 240 volts 4 way double door

S&F in replacement MCB SPN 32 amps 230 volt 10 KA, type B

S&F in replacement MCB SPN 63 amps 230 volt 10 KA, type B

S&F in replacement MCB SP 6 to 32 amps 230 volt 10KA type B

M&L for sub main wiring with two run of 6.0 sqmm single core multi stranded PVC insulated and unsheathed copper conductor of grade 1100 volt FRLSH cable (red for phase and black for neutral) & 6 sqmm copper conductor cable PVC unsheathed green coloured for earthing in and including P[VC casing caping with complete accessories duly connected with earth dolly complete all as specified and as directed

All as per item No 204 above but of size 4 sqmm

Supply and fixing in replacement calling bell ding dong AC 230 volts, single pole

S&F in replacement bell push, flush type, 5 Amp

Supply and fixing LED lamp 10 watts 230V pin type 230 V 50 Hz as directed.

Supply and installed water heater storage type electric (Geyser) of 25 Ltr capacity closed and vertical type suitable for AC single phase 240 volt 50 Hz complete with feroglass technology heating element incoloy glass coated with digital thermostat 7 cutout heavy duty anode rod PUF insulation 5 star rating (rating year 2017) digital LED indicator of warranty period 5 years incl taking down old geyser and deposite the same to AGE E/M Store yard all as directed by Engr-in-Charge.

S&F Exhaust fan 200mm sweep,1400 RPM, metal body with self opening louvers of 230V 50 Hz incl all mounting accessories and connections using three core flexible copper conductor cable complete making all necessary arrangement for mounting on walls/window by cutting/opening/drilling/ of wall/Existing window Exhaust fan and finishing the distrubed surface matching with existing colours complete incl taking down old one and depositing to MES store yard of AGE E/M (CME) all as directed by Engr-in-Charge

S & F three track sliding window with two or more shutter with 4 mm thick plane glass or Toughen glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make including taking down existing old window with frame of any description complete all as specified and directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & vertical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & bottom 20844

S&F aluminium anodised louvered ventilator with 4 mm thick pin headed glass and 100 mm wide glass strips, white framed and fixed with aluminium anodised frames etc including taking down existing old ventilator with frame of any description complete all as sspecified and directed. (a) SP 20048 (b) Glazing clips 19352

Mukund Engineers and Contractors

M/S JAYCONSTRUCTION CO

GGS Infra