ADDN/ATLN OF GATES AND ENTRANCE AND CERTAIN MINOR WORK UNDER GE KAMPTEE.

Amount

Demolition of brick / block masonry built in CM including all quoins, arches, pillars etc and clearing rubbish off the premises complete all as specified and as directed.

Demolition of reinforced cement concrete slabs etc in ground floor and paving n.exc 15 cm thick (below or above ground level) complete all as specified and as directed.

Dismantling structural steel work including , doors, gates but excluding framed truss etc complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.50m deep and getting out in Hard soil complete all as specified and as directed.

M & L for Cement concrete 1:4:8, type D2 as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter Complete all as specified and as directed.

M & L for flat and curved Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. Complete all as specified and as directed.

M & L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions. Rough finished Add for fairsurfaces of finished Square, Circular rectangular on plan or polygonal concrete Complete all as specified and as directed.

M & L for Mild steel bars 10mm dia and over, cut to length, bent to shape reqd, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

M & L for Mild steel bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binderscut to length, bent to shape reqd, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia Complete all as specified and as directed.

M&L for RCC M25 (Design Mix) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L for RCC M25 (Design Mix) as in Columns, pillars, piers, posts and struts complete all as specified and directed

M&L for RCC M25 (Design Mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for brickwork with fly ash bricks, old size, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed.

M&L for rendering 15mm thick in cement plaster in 1:6 fair, finished complete all as specified and as directed.

S&F 16 to 18 mm thick Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including one number SS clamps (grade -202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment complete all as specified and directed

M&L for Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed.

Dismantling floor, heart or wall tiling including cement mortar bedding (but not backing ), removing serviceable tiles to store and rubbish off the premises.

M&L for glazed Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over a layer of fine river sand, watering and consolidating complete. (Note: Sand will be measured paid for seperately under respective item supplied only).

Supply only river bed fine sand for screed bed for paving flooring

Returning, filling in, including spreding, levelling, watering and well ramming in layers n.exc 25cm all as directed.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed Complete all as specified and as directed.

M & L for Framed work for ornamental and intricate design such as Gate, grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for preparation New steel and iron surface not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

Surface excavation in soft /loose soil n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil

M & L for Formwork to soffits of suspended slabs such as Roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or Sloping) and simillar work complete all as specified and directed.

M&L for RCC M25 (Design Mix) using 20 mm graded stone aggregate as in chajja etc complete all as specified and as directed.

M & L for RCC M25 design mix, using 20 mm graded stone aggregate for Roofs, Slabs supported on walls, beams and columns in floors, landings, balconies,canopies, deck slabs and inshelves and the like work complete all as specified and directed.

M&L for PCC (1:2:4)) type B1 using 20 mm graded agg as in benching/padding /moulding on top of chajja junctions etc.complete all as specified and directed

M&L for Rendering 10 mm thick in CM 1:6 on fair faces of brick/concrete work surfaces to be finished even and smooth (without using extra lime or cement complete all as specified and directed..

Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed

M&L for preparing newly plastered surfaces and applying two coats oil bound distemper over a coat of 1mm thick putty over a coat of chlk whiting primer complete on wall as completed all as specified and directed

M&L for Rendering 15 mm thick in CM 1:4 on fair faces of brick/concrete work surfaces to be finished even and smooth (without using extra lime or cement complete all as specified and directed..

M & L for 5mm thick rendering on fair faces of brick work or concrete surfaces in CM ( 1:3 ) finished even and smooth (without using extra lime or cement) on Ceiling complete all as specified and as directed.

M&L for preparing surfaces of any description and applying three coat of white wash on ceiling etc complete all as speciifed and directed.

S&F powder coated aluminium frame for door, window,ventilator with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F powder coated aluminium ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing ,anodised aluminium snap beading, screws etc. complete all as specified

Supply and fix aluminium (powder coated ) three track sliding window comprising of one fly proof shutter and two glazed shutters with frames of size 92.0mm x 31.75mm x 1.30mm thick and shutter frames of size 40mm x 18mm x 1.55mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement complete all as per manufacturer's catalogue and specifications complete all as specified and directed. (Notes : (i) Glass filling in panels of windows and aluminium wire mesh/wire cloth shall be deemed to be included in the quoted rate for the item; (ii) Aluminium alloy wire cloth in panels of wire gauzed shutter shall be 0.45 mm nominal dia of wire and avg width of aperture 1.40 mm, fixed with aluminium wire staples; (iii) Glass filling in panels of glazed shutter shall be 5 mm thick tinted sheet glass of approved make and shade/tint complete all as specified and as directed.

M&L for anodised aluminium door shutters single/double leaf, side hung type, with top and lock rail of size 83X44.45X2mm thick, bottom rail 150X 44.45X2mm thick styles/meeting styles shall be of size 83X44.45X2mm thick including jointing cleats, rubber beading snap fit clips, aluminium screws etc, panels fitted with prelaminated particle board/glass including builders hardware ie aluminium tower bolt 150mm long 2 nos to each shutter , aluminium door handle 200mm long 2 nos to each shutter complete all as specified.(Prelaminated board and glass to be measured & paid separately).

S&F 12mm thick prelaminated particle board (both sides laminated) of interior grade, type-II of approved brand with lamination of approved shades complete fitted in door panels, partitions etc all as specified.

S&F plain sheet glass, ordinary quality 4.8mm thick in panels of aluminium doors/windows/partitions fixed with aluminium glazing clips & rubber beading exc 0.5 sqm each pane complete all as specified.

S&F 4 mm thick Figured glass and glazing with rubber beading and aluminium glazing bar in each panel but exc. 0.5 Sqm each complete all as specified and directed

S&F framed work such as grills ,guard bars with mild steel Square bars with ends of bars shouldered and/ or riveted and similar work confirming to FE 290 Gde-E-165 complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Supply, and fixing 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer in-charge

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as speicified and directed

S&F for 150mm long aluminum, anodized, barrel tower bolts of extruded section and fixed complete all as speicified and directed

S&F 250mm long Aluminum alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed all as directed by engr-in charge.

S&F for 150mm long aluminum handles, cast type, anodized complete all a specified and directed.

M&L for Anti -termite treatment under plinth protection, top surface of filled earth ,bottom and sides of excavation at rate of 5 Ltrs of emulsion per square meter of surface area complete all as specified and directed

M&L for ATT to treating the backfill in contact with foundation at the rate of 7.5 Ltrs of emulsion per square meter of vertical surface complete all as specified and directed by Engr-in-charge

M&L for Hard core of gauge not exc 63mm deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface of 100mm thick with broken/stone/boulers.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) type D2 using 40mm graded aggregate as in sub base complete all as specified and directed

M & L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate)complete all as specified and directed.

Material & labour Non - skid Ceramic coloured tiles 7 to8 mm thick jointed free squarere/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed over 15mm thick screed bed CM 1:6 all as specified and as directed.

Material & labour Non - skid Ceramic coloured tiles 7 to8 mm thick jointed free as in skiriting squarere/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed over 15mm thick rendering CM 1:4 all as specified and as directed.

M&L vitrified ceramic tiles 10 mm thick (square or rectangular) polished, light shed area of each tile not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in site or colored cement to match over 15mm cement screed bed in cement mortar 1:6 as specified and directed.

M&L vitrified ceramic tiles 10 mm thick (square or rectangular) polished, light shed area of each tile not exceeding 0.36 sqm in Skirting etc set and including rendering 10mm thick in cement mortar 1:4 complete all as specified and as direted.

M&L colored glazed ceramic tiles in vertical surface 300x 450x 6-7mm thick set and jointed in neat cement slurry and pointed in site or color cement to match including rendering 10mm thick in cement mortar 1:3 complete all as specified and as direted.

S&F steel water tubing 15mm bore, glavanized medium grade with and including provision of all fittings of ISI marked and concealed complete to walls and ceiling or laid in floors complete

S&F steel water tubing 20mm bore, glavanized medium grade with and including provision of all fittings of ISI marked and concealed complete to walls and ceiling or laid in floors complete

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top)of 1000 litres capacity hoisted and fixed in position and including dismantling water tank and removing from site complete all as specified and as directed.

S&F 20mm bore ball brass valves. high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed.

S&F 20mm dia gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed in floor/wall complete all as specified and as directed.

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and as directed.

S&F PVC (SWR) bends any radius of 75mm bore complete all as specified and as directed.

S&F PVC (SWR) bends any radius of 110 mm bore complete all as specified and as directed.

S&F PVC (SWR) junction double, (double T), equal or unequal of 75mm bore complete all as specified and as directed.

S&F PVC (SWR) junction double, (double T), equal or unequal of 110mm bore complete all as specified and as directed.

S&F PVC (SWR) vent cowl of 110mm bore complete all as specified and as directed.

S&F for PVC (SWR) vent cowl suitable for 75mm dia PVC pipe complete all as specified and as directed.

S&F 100 mm Cast iron nahani, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F PVC 100 mm gully, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F in repairs Vitrous china wash basin, size 555x410x205mm, wall hung Basin with full pedestal and fixing accessories complete all as specified and directed. Make Essco by Jaquar (Cat No-ECS-WHT-801, ECS-WHT- 301) or equivalent complete all a specified and directed.

S&F repairs Single lever basin Mixer without Popup waste with 450mm long Braided Hoses all as specified and directed. Make : Essco by Jaquar (Cat No:APR-101011NB) or equivalent complete all a specified and directed.

S&F s Angular Stop Cock with wall Flange Make : by Jaquar (ORP-10053PM) or equivalent complete all a specified and directed.

S & F 15 mm bore chromium plated bib taps with Wall Flange, cast copper alloy, Fancy type, screwed down, screwed for iron pipe or for brass ferrule Complete all as specified and directed.( CAT: ORP-10037PM Jaquar or requivalent)

S&F in repairs 2 way bib cock with wall fange all as specified and directed Make : Essco by Jaquar (Cat No:APR-101041) or equivalent complete all a specified and directed.

S&F in repairs Bowl for Coupled WC with PP normal close slim seat cover, Hinges, Fixing accessories and accessories Set, size 395X680X770mm, P/s Trap-180mm/ 220mm (Essco by Jaquar Cat No AIS-WHT-101751NSN/AIS-WHT-101751NSN) and cistern with cistern fittings (Essco by Jaquar Cat No - AIS-WHT-101201) Essco by Jaquar or equivalent complete all a specified and directed.

S&F Hand shower (health Faucet) (ABS body) with 8mm dia, 1.2 Meter long Flexible tube & wall Hook all as specified and directed Make : Essco by Jaquar (Cat No ALE-ESS-593) or equivalent complete all a specified and directed.

S&F Towel Rack 600mm long with lower Hangers, Stainless Steel fixed to walls with chromium plated (CP) brass screwsall as specified an directed. Make Essco by Jaquar (AEC-1181) or equivalent.

S&F Towel ring square fixed to walls with chromium plated (CP) brass screws Make Essco by Jaquar (AEC-1121) or equivalent.

S&F Glass Shelf 600mm long fixed to walls with chromium plated (CP) brass screws. Make Jaquar (ACN-CHR-1171N) or equivalent.

S&F Soap dish (polycarbide) fixed to walls with chromium plated (CP) brass screws Make Essco by Jaquar (AEC-1133) or equivalent.

S&F Toilet Paper holder fixed to walls with chromium plated (CP) brass screws Make Jaquar (AEC-1151) or equivalent.

M&L for vitreous china urinal, Half stall type, white (excluding flushing cirstern) complete providing and fixing plugs bedding urinal against wall , pointing around urinal back side,suitable Waste pipe for urinal, CP uniral spreader,connection, 15 mm CP push cock and grating etc complete all as specified and directed

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed

S&F in Repairs 32mm Waste fittings, brass,chromium plated for glazedw are sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed

M&L for PCC 1:4:8 type D2 as in concrete bed to drain pipes of 200mm bore including packing under and haunching against the sides of pipe after they are laid complete all as specified and directed

M&L for Reinforcement concrete pipes, class NP-2 laid and jointed complete with collars for 200 mm bore dia of pipe.

M&L for precast RCC (1:2:4) type B1 using 20mm graded stone aggregate as in cover slabs etc set in cement mortar (1:4) including use and waste of form work & placing on drains complete directed

M&L for PCC (1:2:4) type B1 using 20 mm graded agg as in coping etc inclduing necessary form work complete all as specified and directed

M&L for PCC (1:2:4)) type B1 using 20 mm graded agg as in benching etc complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends complete all as specified and directed

All as per item No. 97 above but and add or deduct for each 25mm girth or part thereof over or under 30 cm complete all as specified and directed

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching and forming branch channel 91/1 round or 3/4 section ) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as orginal formation complete all as specified and directed

M&L for provision of water proofing treatment by using APP torch on non woven polyster film reinforcement with 3 mm thick and weight not less than 3.50 kg/sq m over roof and vertical surfaces including preparation of surfaces and applying oil/water based bituminous primer coat @ 0.30 ltr per sqm on clean and dry surface and then providing APP membrane laid with 100 mm over lap on both sides all as per manufacturer's instructions including 15mm thick plaster in CM 1:3 and aluminium paint over membrane complete all as specified and directed.

Supply only liquid water proofing admixture of make-pidilite or equivalent complete all as specified and as directed.

M&L 75mm thick PCC 1:3:6 type C-2 as in plinth protection fixed even and smooth with out using extra cement complete all as specified and directed

Excavating over areas, n exc 1.5 m deep and getting out out in Hard soil.complete all as specified and directed

Excavating in post holes in hard /dense soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation of post holes complete all as directed.

M&L for roof trusses framed trussed pulins crance rails and fastening and heavey brackets framing ( Beam tee, angle, chall or flat sections indl distance pieces, cleats etc Fe-410W (Gde E 250) complete all as specified and directed

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as sepcified.

M&L for preparation New steel and iron surface not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for two coats of cement base paint over a coat of primer on newly plastered surfaces of walls including preparation of surfaces complete all as specified and directed

M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts. grade FRLSH PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit not less than 20 mm dia with all accessories and FRLSH PVC insulated 1.5 Sqmm multi standard sheathed copper wire for continues earth, including cutting and chasing of wall surface for laying PVC conduit and modular sunken box and connecting earth. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles. Note :Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following :- (a) One light /fan point controlled by one switch

All as per item No. 110 above but One 5 pin socket outlet 6 Amps on independent board

Supply and fixing modular switch piano single pole, one way 6 Amps 1 module, complete all as specified and directed.

Supply and fixing modular socket outlet 2/3 pin 6 Amps combined 2 module, complete all as specified and directed.

Supply and fixing modular step type, 2 module electronic fan regulator heavy duty 120watts 240 volts. , complete all as specified and directed.

Supply& fixing ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 3 module for mounting switch and sockets complete all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 8 module for mounting switch and sockets all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Supply and fixing LED luminaire 595 mm x 595 mm, 36 watt, 220 V AC, 6500 K recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting complete all as specified and directed.

Supply and fixing of wall mounting fan 400 mm sweep, 230 volts, AC, single phase complete with all fixing accessories all as per site requirement and as directed.

Supply & fix sheet metal enclosure MCB distribution board double door. Single pole & neutral 240 volts 6/8 way with 200 amp rated bus bar

Supply and fixing miniature circuit breaker (MCB) single pole of capacity 6-32 Amps rating 240V, 10KA 'C' curve and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing miniature circuit breaker (MCB) single pole and neutral of capacity 32 Amps rating 240V, 10KA 'C' curve and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

M&L for sub main wiring using two 2x 1.5 sqmm single core PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x1.5 Sqmm as earth continuity conductor connected to earth dolly complete all as specified and directed. (NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.)

Materials and labour as in replacement for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:- (i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep in soft/loose soil and getting out for taking down/laying pipe lines of any description and in any position / laying of cable trench, pole and stay foundation including forming sides and bottom surface to required level / gradients complete all as specified and directed.

Supply and fix Double wall corrugated High Density Polymer Ethyl(HDPE) pipe for laying of electric cable of size 50 mm outer diameter and 38 mm inner diameter with IS 14930 (part 2) 2001 and 6mm thickness laid in trenches(Including cutting of roads or any others hard surfaces and making good disturbed surfaces) , wall, poles including bends, sockets and other connected accessories complete all as specified and directed.

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including fixing of light on gates with stand and iron fittings, complete all as specified and directed

Supply and lay XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sqmm 2 Core, Complete all as specified and directed

Supply & fix sheet metal enclosure MCB distribution board double door. Single pole & neutral 240 volts 4 way with 200 amp rated bus bar complete all as specified and as directed.

Supply and fixing GALAKTIC SMART STRIP LIGHT - (RGB) 3000 K IP65 5 Mtr), High brightness IP65 LED strips with uniformity of light required for perfect outdoor application Complete all as specified and directed.

Supply and fixing Flexion AC LED strip Rope 144D Strip 3000 K IP65 50 Mtr (Warm White), High brightness IP65 LED strips with uniformity of light required for perfect outdoor application Complete all as specified and directed.

Supply and fixing BRILLANTE LINEAR WALL WASHER 6H 7 W 3000 K, Crafted from Aluminum Die Cast with Bi-Directional Beam. Its integrated LED ensures long-lasting and energy-efficient with IP65 Protected.

Supply and fix thermoplastic cable entry junction boxes of size 250 x 220 x 135 mm and IP-65 protection level with metric knock out fixed on poles with MS clamps, nuts, bolts and washers including MCB SPN, 6-32 amps, 'C' series, breaking capacity 10 KA, 'C' curve 240 volts, 50Hz including necessary incoming and outgoing electric connection with suitable size of copper lugs etc., separate (detachable) gland plate, bakelite connector 4 way 20 amp, dust and vermin proof, front door opening with hinges and locking arrangement, complete all as specified and as directed.

Material and labour for PCC Type C2 ,1:3:6 by using ( 40 mm aggregatestone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets andrailings upto 60 cm in height, copings, complete all as specified and directed.

Supply and fix Steel tubular swaged poles complete with cast iron base plate, final taper plug, bolts, nuts and screws as specified type 410 SP-31 (9 metres long) complete all as specified and directed.

Supply and fix in repair LED street light luminaries of capacity 60 watts with pressure die cast aluminium housing heat resistance toughened glass, IP 66 protection complete with direcer, including twin twisted copper flexible wire of size 0.75 Sqmmm for connection for street light fitting to OH line or junction box, fixing acessories and including suitable Bracket made out of 40mm dia GI light grade pipe, 1.20m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FO clamps 50 x 6mm to be tightened with suitable size of bolts, nuts and washers and inclduing painted with two coat of aluminium paint over a coat of red oxide primer, competed all as specified and directed. Make Cat No. LSRT01S060XC of Jaquar or equv.in Philips, CG, Luker

Supply and laying in trenches or fixing in walls / poles or drawing through pipe XLPE insulated, screened,PVC bedded, galvanised steel strip or wire armoured,electric power cables ( heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 16 sq mm,4 core including testing after laid and jointed all as specified and as directed Note :- Excavation and earth work, cable protection shall be measured and paid separetely.

Supply and installation , commissioning & Testing wall mounted air cooled split units indoor/outdoor complete with cordless remote control unit electric drive single phase of capacity 2 Ton and with in built air ioniser and Plasma filter for better indoor air quality of capacity 2 TR complete with all accessories including making all arrange ment for fixing indoor & outdoor units , making necessary hole with bracket in wall to pass tubing and cables and grounting bolt in wall , connecting suction & discharge of copper tubing and cables , copper tubing including cutting brazing, flaring and testing of size 1x4”x22SWG in required length as per site including insulating piping & Gas Charging complete all as specified & directed

Supply and installation, commissioning & Testing wiondow type AC 2 Ton complete with cordless remote control unit electric driver single phase of capacity 2 Ton and with in built air ioniser and Plasma filter for better indoor air quality of capacity 2 TR complete with all accessories including AVC stand fixed in wall & Gas Charing complete all as specified and directed. Make - LG/Voltus/Blue star

M&L for sub main wiring surface type with 2 runs of 6 Sq.mm for phase, neural and 4 Sq.mm for earth continuity PVC insulated unsheathed cable FR grade with copper conductor single core multi stranded 1100V grade confirming to IS-694 drawn through and including 20mm dia concealed stove enamelled steel conduit (Heavy grade as per IS-9537, Part-III) including conduit including steel conduit accessories not less than 20mm dia including conduit accessories junction boxes etc., complete all as specified and directed. Note:- 2 Runs of 6 Sqmm + 1 Run of 4 Sqmm cable, 1 Run of steel conduit shall be measured as 1 RM.

Supply and fix MCB SPN 63 Amp 10 KA "C" curve complete all as specified and directed.

S&F single pole and neutral encloser with a two pin and earth plug and socket complete with one single pole 20 Amp 10 KA, C series MCB 240 volt complete all as specified and directed.

S&F MCB Isolator TPN 100 Amp, 415 volt complete all as specified and directed.

S&F factory made, sheet metal distribution boards, TP & N 4 ways duouble door protection class IP-42 suitable of mounting MCB / MCCB complete all as specified and directed.

NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs. 19,758.36]

DEESHA CONSTRUCTIONS

Asha Enterprises

M/s ABHIMAN HEGDE

M/s Jagdish Staioners and General Stores

M/s M.G. Hargunani

S R BUILDERS

M/s B S Jain

Bidder Name

M/s ABHIMAN HEGDE

SHIV SHANKAR MISHRA

DEESHA CONSTRUCTIONS

M/s B S Jain

Asha Enterprises

M/s Jagdish Staioners and General Stores

M/s M.G. Hargunani

S R BUILDERS