Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹2.2 Cr
EMD Value
₹4.4 L
Closing Date
25 Jan 2025, 5:30 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Engine Division, Koraput
HINDUSTAN AERONAUTICS LIMITED Engine Division, Koraput, Sunabeda- 763002
UP GRADATION OF EXISTING SEWAGE TREATMENT PLANT.
8061
W-08/24-25
Works
Mig Complex- Engine Divn-Koraput-Civil
₹0
₹4.4 L
25 Jan 2025
20 Jun 2024
20 Jun 2024
25 Jan 2025
ANNEXURE-A (CIVIL WORKS)
Earth work in surface excavation in all kind of soil not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge.
Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. etc. all complete as per direction of Engineer in charge.
Labour charges for filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and for all lifts etc. all complete as per direction of Engineer in Charge.
Earth disposal by Mechanical transport including loading, unloading and stacking upto 01 Km distance .The rates will be applicable to net quantities after deduction of prescribed percentage for voids mentioned in the specification. all complete as per direction of Engineer In Charge.
Supplying, carrying to site all approved materials diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete with Chlorpyriphos/ Lindane E.C. 20% with 1% concentration etc. all complete as per direction of Engineer in charge.
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete etc. all complete as per direction of Engineer in chrge.
Supplying, carrying to site all approved materials and providing and laying in position cement concrete of 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) excluding the cost of centering and shuttering - All work up to plinth level etc. all complete as per direction of Engineer in Charge.
Supplying, carrying to site all approved materials and providing and laying in position cement concrete of 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) excluding the cost of centering and shuttering - All work up to plinth level etc. all complete as per direction of Engineer in Charge.
Supplying carrying to site all approved materials extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials and making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth etc. all complete as per direction of Engineer in charge.
Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work of Concrete of M25 grade with minimum cement content of 330 kg /cum using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement etc. all complete as per direction of Engineer in charge.
Centering and shuttering including strutting, propping etc. and removal of form for the same etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials and placing in position steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more for R.C.C. work including straightening, cutting,bending, placing in position and binding etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and providing Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) etc. all complete as per direction of Engineer in charge.
Providing wood work with second class teak wood in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) etc. all complete as per direction of Engineer in charge.
Providing and fixing ISI marked 35mm thick flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked Stainless Steel butt hinges with necessary screws etc. all complete as per direction of Engineer in charge.
Providing and fixing ISI marked 30mm thick Pre-laminated flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and plywood face panels commercial type on both sides. The work includes provision of 1.0 mm thick high pressure decorative laminated sheet of plain /wood grain in gloss/matt/suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S including cost of adhesive of approved quality , fixing on both front and back face of the block board shutter etc. vision panels if any provided shall be paid extra for glass items, the work also includes ISI marked SS butt hinges with necessary screws etc. all complete as per direction of Engineer in charge.
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Cleosetory windows & other Frames/Chowkhat of size 65x 100mm comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made etc. all complete as per direction of Engineer in charge.
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately etc. all complete as per direction of Engineer in charge.
Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately) etc. all complete as per direction of Engineer in charge.
Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS-710 of approved brand boxes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer in charge.
Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.
Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in Charge.Wire mesh/ glazing of plain/ toughened / laminated / double glass unit with / without high performance coatings as per design requirement and conforming to IS : 3548 & IS : 16231 shall be paid separately etc. all complete as per direction of Engineer in charge.
Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.
Wire mesh / Glazing of plain / toughened / laminated/double glass unit with / without high performance coating as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately etc. all complete as per dierection of Engineer In charge.
Providing and fixing IS : 12817 marked stainless steel butt hinges of size-100x60x2.50 mm (heavy weight) with stainless steel screws etc. all complete as per direction of Engineer in charge.
Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. all complete as per direction of Engineer in charge.
Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-chargec.
Providing and fixing special quality bright finished 50mm brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. all complete as per direction of Engineer in charge.
Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and fixing in position brass antique finish tower bolts ( barrel type) with necessary screws etc. all complete as per direction of Engineer in charge.
Supplying, Providing and fixing in position chromium plated brass Heavy duty mortice door lock set with three keys for Home / office / Hotel of Satin white & chrome / satin black matt finish.The components of the mortice door lock set shall contains 1- 85x45 mm or nearer lock body ,2-mortice zinc door lock handles(Lever handle with rose & escutcheons), 1 piece of 60mm or nearer zinc thumb turn cylinder, 3 brass keys , along with a receptacle plate & screws for fittings,lock type- Key lock etc. all complete as per direction of Engineer in charge.
Supplying, Providing and fixing in position chromium plated approved quality Mortice door locks with keyless handle set ,material with brass chrome finish along with one brass baby latch etc. all complete as per direction of Engineer in charge.
Supplying , providing and fixing in position Digital lock ( smart door) with minimum 2 in 1 access for main doors with Pin access / RFID card access , mechanical key system. The lock to be facilitated with USB battery backup & auto locking, with necessary fittings etc. all complete as per direction of Engineer in charge.
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. all complete as per direction of Engineer in charge.
Providing and fixing in position bright finished 100mm size brass handles with screws etc. all complete as per direction of Engineer in charge.
Providing and fixing in position 300mm stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete etc all complete as per direction of Engineer in Charge.
Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately) etc. all complete as per direction of Engineer in charge.
Providing and fixing triple strip vertical type magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete etc. all complete as per direction of Engineer in charge.
Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron), aluminium work for doors, windows, ventilators, partitions, cupboards, cabinets and similar works with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) etc. all complete as per direction of Engineer in charge.
Providing and fixing 12.5 mm thick tapered edge gypsum moisture resistant board false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long,
the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting etc. all complete as per direction of Engineer in charge.
Providing and fixing with false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,
including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60,etc. all complete as per direction of Engineer in charge.
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) etc. all complete as per direction of Engineer in charge.
Providing and laying Double charge vitrified tile polished finish in floor of size of Tile 600x1200 mm(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. etc all complete as per direction of Engineer In charge.
Providing and laying 18 mm thick Italian Marble stone slab, Perlato, Rosso verona,Fire Red or Dark Emperadore machine cut, mirror polished, Italian marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
Providing and laying Nonskid / Matt finished Vitrified tiles in floor of size of Tile 600x1200 mm(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. etc all complete as per direction of Engineer In charge.
Chequerred precast cement concrete tiles Medium shade pigment using 50% white cement 50% Grey cement of 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). etc. all complete as per the direction of Engineer-in-charge
Supplying carrying to site all approved material and Rendering 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In-Charge.
Supplying, carrying to site all approved materials and plastering with 15 mm thick cement plaster on rough side of single or half brick wall of mix 1:4 (1 cement: 4 coarse sand) etc. all complete as per direction of Engineer in charge.
Supplying , carrying to site all approved materials and applying priming coats with one coat of primer with water thinnable cement primer on wall surface having VOC content less than 50 grams/litre approved brand and manufacture etc all complete as per direction of Engineer in charge.
Supplying , carrying to site all approved materials and Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete etc. all complete as per direction of Engineer in charge.
Supplying , carrying to site all approved materials and applying two or more coats of paint applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surface. Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. all complete as per direction of Engineer in charge.
Supplying , carrying to site all approved materials and applying two coats of wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying more coats wherever required to achieve even shade and colour etc. all complete as per diection of Engineer in charge.
Supplying carrying to site all approved materials and Painting two or more coats on steel surface on new work over an under coat of suitable shade with ordinary paint with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade with preparation of surface etc. all complete as per direction of engineer in charge.
Supplying carrying to site all approved materials and painting with two coats of aluminium paint on steel Surface on new surface. The work includes surface preparation etc. all complete as per direction of engineer in charge.
Supplying carrying to site all approved material, providing and fixing in position float glass panes 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm) etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials and Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints for internal and external work exposed on wall etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials and Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints on concealed work, including cutting chases and making good the walls etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials and providing, Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints for external work in trenches etc. all complete as per direction of Engineer in charge.
Supplying, providing and fixing in position CPVC Ball valves of different dia. as per requirement of the site etc. all complete as per direction of Engineer in charge.
(5) External reinforcement C channel at every 1 – meter of steel ith anticorrosive paint and it is tie with top external tie roads (If tank height is more than 1 meter) . (6) Internal roof supports should be of FRP/GRP 5mm thick hollow square section. (7) Air –vent dia 50/100 mm with mosquito proof mesh insect proof. (8) Aluminium body water level indicator with clear tube type and brass nozzle. (9) Internal FRP ladder with wall mounting arrangement inside. (10) External G.I ladder with complete fixing arrangement outside. (11) Complete Fixing of inlet/ outlet/overflow/ drain should be G.I flange type with 9” long Nipple etc. all complete as per direction of Engineer in charge.
Supplying,providing & fixing in position 15mm dia. CP brass wall mounted wash basin mixer with concealed body valve for mixer and wall flange,extended operating lever,complete with all accessories etc. all complete as per direction of Engineer in charge.
Providing and fixing 15mm dia. C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. etc. all complete as per specification and direction of Engineer-in-charge.
Providing and fixing 15mm dia. C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 etc. all complete as per specification and direction of Engineer-in-charge.
Supplying, carrying to site all approved materials and fixing in position 20mm dia. Stainless steel wall mount towel rail 600mm long etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and fixing in position Stainless steel wall mount towel rack 600mm long with out lower hanger nut with 3 nos hooks etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials ,providing and fixing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and fixing in position chrome finish bottle trap of 32mm of approved quality and make etc. etc. all complete as per direction of Engineer in charge.
Providing and fixing 15 mm nominal bore with 45 cm length unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colours etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and fixing in position 32mm dia half thread click clack waste coupling for wash basin/Bowl urinal etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and fixing in position soap dish holder polycarbonate with chrome finish etc. all complete as per direction of Engineer in charge.
Providing and fixing in position wall mounted liquid soap Dispenser with glass or polycarbonet bottle, the holder shall be of stainless steel SS 304 or brass chrome finished including all accessories as required etc. all complete as per direction of EIC
Supplying,providing & fixing in position Wall mounted multifold mini hand tissue paper dispenser with necessary fixtures etc. complete as per specification and direction of EIC.
Supplying, carrying to site all approved materials and fixing in position Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long etc. all complete as per direction of Engineer in charge.
Supplying ,providing & fixing in position 15mm CP brass single lever concealed bath and shower wall mixer with diverter, the concealed part shall be three way concealed high flow diverter mixer kit for bath and shower system with divertor knob,diverter assembly catridge sleeve. The upper part / exposed parts compatible with with the diverter shall be consisting of operating handle and plate,wall flange(with seals),button , chrome finished etc. all complete as per direction of Engineer in charge.
Supplying ,providing & fixing in position brass chrome finish easy clean over head rain shower of 15 to 20 mm inlet, 200mm dia ,for bath room with support extended arm, silver chrome finish ,fixed with necessary accessories etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials ,Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball, 25 mm nominal bore, 152mm long, weighing not less than 440 gms etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials ,Providing and fixing C.P brass extension nipple size 15mmx50mm of approved make and quality etc. all complete as per direction of Engineer in charge.
Supplying,Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS 5382, leaving 10 mm gap for thermal expansion , (i) single socketed pipes. Complete as per the direction of EIC
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. all complete as per direction of Engineer in charge. (i) 87.5 degree bend
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. all complete as per direction of Engineer in charge. Single tee without door.
Supplying carrying to site all approved materials and providing PVC (SWR) vent cowl etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials and providing 75mm dia outlet PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement etc. all complete as per direction of Engineer in charge.
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials and Fixing Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink with drain board as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required of size 510x1040 mm bowl depth 250 mm etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and fixing Vitreous china extended wall mounting wash down water closet /wall hung EWC white/ ivory/ off white closed pattern including all necessary accessories like rag bolts/gel gasket etc. The work also includes provision of dual flush plate polished chrome finish, single piece slim concealed cistern wall/floor mounting full frame installation and S type drain pipe connection set for all wall hung EWC with flushing capacity of 6 litre/3 litre (Total capacity 9 litre) , cost shall be inclusive of providing and fixing of accessories i.e,wall plate for flushing cistern, UF soft close slim type seat cover and cistern fittings ,nuts,bolts, hinges and gaskets,SS rack bolt/anchor bolts/fastners for EWC hanging etc. all complete as per direction of Engineer in charge.
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 X 390 X 370 mm having pre & post flushing with water (250 ml & 500 ml consumption ), having water inlet from back side , including fixing to wall with suitable brackets all as per manufacturer specification and direction of Engineer-in-charge.
Supplying carrying to site all approved materials ,providing and fixing Granite stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) and finished smooth etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials ,providing and fixing Half pedestal wash basin of size-550x450mm or nearer excluding taps, waste pipes, chain and plug and porcelain stopper but including brackets etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing C.P brass 2 way bib cock with wall flange along with all necessary accessories complete incluring cutting, making good the walls , floors, slab wherever required etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing 100mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside for soil, waste and vent pipes as per IS-15905 etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials,providing and fixing M.S. holder-bat clamps for 100 mm dia pipe of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing 100mm dia bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing 100mm dia plain bend of required degree complete Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing 100mmx100mmx100mmx100mm dia double equal plain junction of required degree complete Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing 100mmx100mmx100mm dia single equal plain junction of required degree complete Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing 100mm terminal guard hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing 100mm dia. shielded coupling for hubless centrifugally cast (spun) iron pipe of SS 304 grade coupling with EPDM rubber gasket complete etc. all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and fixing in position self cleaning gravity filter unit for Rain water Harvesting system suitable for area upto 350 Sqm to cater the rainfall intensity of 75mm/hr with flow rate of 300-340 LPM. The filter should consist of SS 304 screen, 250 microns mesh with inlet size 110mm and outlet 90mm etc. including all necessary accessories required for fixing the unit with the wall surface and its connections etc. all complete as per direction of Engineer in charge.
Providing and laying non-pressure 150 mm dia. R.C.C. pipe NP2 class (light duty) with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. all complete as per direction of Engineer in charge.
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 etc. all complete as per direction of Engineer in charge.
Extra for depth for manhole of size-90x80 cm etc. all complete as per direction of Engineer in charge.
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 etc. all complete as per direction of Engineer in charge.
Extra for depth for manhole of size-120x90 cm etc. all complete as per direction of Engineer in charge.
Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain for pipes 100 to 250mm diameter etc. all complete as per direction of Engineer in charge.
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works and applying a priming coat of approved steel primer using structural steel etc. all complete as per direction of Engineer in charge.
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. all complete as per direction of Engineer in charge.
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and laying 40 mm thick with 20 mm nominal size stone aggregate Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with out floating coat. etc. all complete as per direction of Engineer in charge.
TOTAL(ANNEXURE-A): CIVIL WORKS
ANNEXURE-B (ELECTRICAL WORKS)
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C (Guest House)
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. (For Staircases,lift,VIP Room)
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C (For GH Corridor Lighting )
Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.
Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. Size : 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit/Floor raceways complete as required. Size : 2 Pair
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. Size : 1 run of cable
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.( For LAN, Telephone, TV)
iii) 32 mm
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
15/16 A switch
6 pin 15/16 A socket outlet
5/6 amps switch
6 pin 15/16 amp socket outlet
Bell Push
Telephone socket outlet
TV antenna socket outlet
Electronic Buzzer,230 V, 1 / 2 module
20 amps DP Switch 2 module with Indicator
Foot Lamp / Skirting Light, 230 V, 3 module
RJ45 LAN Socket Outlet, CAT 6
25 Amps AC Starter
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
Supplying and installation of 15 ltr capacity geyser including connection etc. as required.
Supplying and installation of 2 ton Split ACs with 5 star rating including, connection etc. as required.
Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.
1 or 2 Module (75 mm X 75 mm)
6 Module (200mmX75mm)
8 Module (125mmX125mm)
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 225 mm width X 50 mm depth X 1.6 mm thickness
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 225 mm width X 50 mm depth X 1.6 mm thickness
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 225 mm width X 50 mm depth X 1.6 mm thickness
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Cross member” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 225 mm width X 50 mm depth X 1.6 mm thickness
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 225 mm width X 50 mm depth X 1.6 mm thickness
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required.
Supplying and fixing PVC batten/ angle holder including connection etc. as required.
Supplying,installation,testing and commissioning of energy efficient 12-15 watt LED sleek downlighter , surface/recess mounted luminaire having efficient diffuser complete with electronic driver i/c connection suitable for operation on 230v,50 Hz supply etc complete as required.
Supplying,installation,testing and commissioning of energy efficient 18-20 watt LED sleek downlighter, surface/recess mounted luminaire having efficient diffuser complete with electronic driver i/c connection suitable for operation on 230v,50 Hz supply etc complete as required.
Supplying,installation,testing and commissioning of energy efficient surface mounted 6 watt LED downlighter having lumen output not less than 100 lumen/watt , surface/recess mounted luminaire having efficient diffuser complete with electronic driver i/c connection suitable for operation on 230v,50 Hz supply etc complete as required.
Supplying,installation,testing and commissioning of Energy efficient surface/recess mounted LED luminaire made up of Die cast Alluminium / CRCA steel of 600 X 600 mm (2" x 2") size with not less than 36 Watt and lumens output 100 lumens/watt with electronic driver and all other accessories suitable for operation on 230 V, 50 Hz supply as required.
Supplying,installation,testing and commissioning of 600 mm long Sleek LED 10 watt mirror light batten fitting with extruded polycarbonate housing, High optically efficient diffuser, above wash basin complete with all accessories etc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
Supplying,installation,testing and commissioning of wall mount decorative LED light fitting having nickel/SS mounting base with acrylic diffuser (white) i/c one number 9 watt LED bulb suitable for 230 volts, 50 Hz AC supply as required.
Supplying, installation of 300 mm sweep 1400 RPM heavy duty exhaust fan with metal louver shutter of suitable size in the existing opening suitable for 230 V 50 Hz AC supply connection, testing, commissioning etc. as reqd.
Supply, Installation, Testing and Commissioning of 400 mm sweep, ISI mark wall fan with all accessories suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2 + 4 way, Double door
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)
6 way (4 + 18), Double door
8 way (4 + 24), Double door
Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Single pole(5-32 amp)
Double pole (32 A )
63 amp TPN
100 A, FP MCCB , 30 kA thermo magnetic release type MCCB with spreader link & ROH
Outdoor LT feeder pillar : Supplying, installation, testing & commissioning of cubical type Outdoor type LT feeder pillar suitable for 415V, 3 Phase, 4 Wire 50 Hz AC supply system of suitable size fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having 400 A capacity extensible type four strip aluminium bus bars of high conductivity, DMC / SMC bus bar supports bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, entire panel shall have a common GI earth bar 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of aluminium bus bars and control wiring with 2.5 sq. mm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c providing and fixing of following switchgear and components complete as required.
Incomer-1 i) 250 A, FP, 36 kA, MCCB thermo magnetic release type with spreader link & ROH - 01 No. ii)1 set of 300/5 A ratio CTs ,Cl:-1,10VA iii)1 Setof LED type indicating lamps(RYB) with 6 Amps FP MCBs for Instrument Protection iv)Multi Function Meter -1 no Incomer-2 i) 250A, FP, 36 kA, MCCB thermo magnetic release type with spreader link & ROH - 01 No. ii)1 set of 300/5 A ratio CTs ,Cl:-1,10VA iii)1 Setof LED type indicating lamps(RYB) with 6 Amps FP MCBs for Instrument Protection iv)Multi Function Meter -1 no Outgoing i) 125A, FP, 36 kA MCCB,thermo magnetic release type with spreader link & ROH -03 No. ii) 200 A, FP, 36 kA MCCB,thermo magnetic release type with spreader link & ROH - 02 Nos iii) 100A, FP, 25 kA MCCB,thermo magnetic release typewith spreader link & ROH - 01 Nos iii) 63A, FP, 25 kA MCCB,thermo magnetic release typewith spreader link & ROH - 02 Nos
Street Light Feeder Pillar
Supplying, installation, testing & commissioning of cubical type LT Outdoor feeder pillar suitable for 415V, 3 Phase, 4 Wire, 50 Hz AC supply system of suitable size fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having 100 A capacity extensible type four strip aluminium bus bars of high conductivity, DMC / SMC bus bar supports, bottom base channel of MS section not less than 75 mmx 50 mm x 5 mm thick, entire panel shall have a common GI earth bar 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of aluminium bus bars and control wiring with 2.5 sq. mm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c providing and fixing of following switchgear and components complete as required.
Incomer i) 63 A, FP, 25 kA MCCB with spreader link & ROH - 01 Nos iii) 1 Set of LED type indicating lamps(RYB) with 6 Amps FP MCBs for Instrument Protection Outgoing i) 32 A , FP , 16 kA MCCB- 4 nos ii) 32 amp power contactor - 1 no iii) Astronomical timer switch - 1 no iv) 100/5 amp,15 VA CT-1 set
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and eatering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.
Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
Providing and fixing 6 SWG dia GI wire on surface or in recess for looping earthing along with the existing surface / recess conduit / submain / cable as reqd.
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting / sweating and soldering etc as required.
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.
Supplying & Erection of hot dipped galvanized 6 mtr height octagonal pole made out of 3 mm thick sheet having 60-70 mm top in approved design with 200 mm x 200 mm x 12mm GI base plate with 1 mtr long (approx) single sided GI bracket , 600 mm long 'J' type GI foundation bolts with RCC foundation (size:450 mmx450mmx1200mm depth ) (1:2:4 with 8 & 12 mm reinforcement) neat plastering outside the foundation with integral control gear having bakelite sheet complete with DIN rail, 6 Amp SP 'C' type MCB , cable entry pipe of 63 mm HDPE pipe in foundation etc. (Design & drawing to be approved by Engineer-in-Charge)
Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 4.5 metre and upto 6.5 metre
Supplying and fixing of 32 mm dia X 2.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.
Providing & fixing of LED type wattage not less than 45 / 50 watt street light luminaire operated on 240 volt, single phase made in all aluminium housing with epoxy primer & baked on ultra durable powder coat, heat resistant toughened glass cover, (IP-65) environment protection, complete with driver circuit on the existing pole including making connections using copper lugs etc. complete as required.
Supplying, installation,testing and commissioning of energy efficient LED flood light luminaries having wattage not more than 100 watt and lumen output not less than 110 lumen/watt, made of aluminium die cast housing with IP66 protection complete with electronic driver and all other accessories suitable for operation on 230v,50 Hz supply etc complete as required.
Supplying and laying of following size PVC insulated and PVC sheathed copper conductor multicore round flexible power cable of 1.1 kV grade etc. as required. 3 x 1.5 sq. mm
Supplying of following size PVC insulated and PVC sheathed / XLPE aluminium conductor armoured power cable of 1.1 kV grade etc. as required. Size : 3.5 x 185 sqmm
Supplying of following size PVC insulated and PVC sheathed / XLPE Aluminium conductor armoured power cable of 1.1 kV grade etc. as required. Size : 4 x 4 sq.mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL/HDPE pipe as required.
Upto 35 sq. mm
Above 95 sq. mm and upto 185 sq. mm
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.
63 mm dia (OD-63 mm & ID-51 mm nominal)
120 mm dia (OD-120 mm & ID-103 mm nominal)
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated & PVC sheathed / XLPE aluminium conductor cable of 1.1KV grade as reqd. Size : 3½ X 185 sq. mm (57mm)
Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.
TOTAL(ANNEXURE-B) ELECTRICAL WORKS
TOTAL (ANNEXURE-A+ ANNEXURE-B)
I / We hereby quote percentage above (+) or below (-) the Estimated cost
Sub Total Works Amount
ADD GST @ 18% (( IGST18%) or (CGST @ 9% +SGST@ 9%)), Whichever is applicable
ADD CESS @ 1%
GRAND TOTAL
Note : (i) : It is a percentage rate tender. Hence the tenderers are required to quote rates on percentage basis i.e. above or below the estimated cost put to tender. (ii) The quoted rates in the bill of quantities are inclusive of all types of taxes, duties levies, fees and charges etc., imposed by Central/ State Govt. and local bodies Compensation Cess, Labour Cess, Custom Duty, royalties and other levies. It shall also include all other costs including loading, un-loading, insurance, transportation, testing and Certification expenses except GST . GST at the prevailing percentage is added in the BOQ at the end.
GOODS AND SERVICE TAX (GST)
Bidder should indicate GSTIN No. (Copy of GST registration to be enclosed) and PAN No. (copy of PAN to be enclosed).
Tender will be considered/ accepted, if & only if the vendor has a valid GST Registration No
Central Tax/ State Tax/ Integrated Tax/ Union Territory tax to be quoted as per GST Law
Bidders to ensure correct applicability of Central Tax/ State Tax/ Integrated Tax/ Union Territory tax based on the Inter / Intra state movement Supply of goods and provision services or both
Bidder shall mention the SAC Code/HSN Code for goods and services in accordance with GST law in their Bid and subsequently in their tax invoice. HAL, Koraput Division shall not be responsible for any error in SAC Code/HSN Code for goods and/or services specified by supplier/contractor
The Tax Invoice for supply of Goods & Services should be raised as per the provision of GST Act & Rules and must compulsorily mention the following
a. HAL, Korpaut Division GST registration number as 21AAACH3641R1ZJ
b. Name & address of supplier / Vendor/ Contractors
c. GSTIN of Supplier / vendors / Contractors
d. Consecutive Serial Number & date of issue
e. Description of goods or services
f. Total value of supply
g. Taxable value of supply
h. Tax Rate – Central Tax & State Tax or Integrated Tax, Cess
i. Amount of Tax charged
j. Place of supply
k. Address of delivery if different from place of supply
l. Signature of authorized signatory
Reimbursement of GST to the vendor is contingent upon complying with the following condition by the service provider
i. Uploading the (invoices raised on HAL, KoraputDivision ) onward GST Return (GSTR-1) in GSTN Network portal within the statutory time period
ii. Discharging the GST tax liability to the Government.
iii. Submission of Tax Invoice to HAL, Korpaut Division.
iv. Submission of proof of payment of GST to HAL, Korpaut Division.
v. Receipt of goods / services by HAL Koraput Division.
vi. Availment of Input Tax Credit by HAL, Korpaut Division .
In case GST credit is delayed/ denied to HAL, Korpaut Division, due to non/delayed receipt of goods and/or services and/or tax invoice or expiry of timeline prescribed in GST Law for availing such ITC, or any other reason not attributable to HAL, Korpaut Division, GST amount shall be recoverable from Vendor along with interest & penalty levied/ leviable on HAL, Korpaut Division, as the case may be
In case vendor delays declaring such invoice in his return and GST credit availed by HAL, Korpaut Division is denied or reversed subsequently as per GST law, GST amount paid by HAL, Korpaut Division towards such ITC reversal as per GST law shall be recoverable from vendor/contractor along with interest & penalty levied/ leviable on HAL, Korpaut Division.
In case of discrepancy in the data uploaded by supplier in the GSTN portal or in case of any incomplete work/service, then HAL, Korpaut Division will not be able to avail the tax credit and will notify the supplier of the same. Supplier has to rectify the data discrepancy in the GSTN portal or issue credit note (details to be uploaded in GSTN portal).
For any such delay in availing of tax credit for reasons attributable to vendor (as mentioned above), interest as per the GST Act & Rules, along with penalty, if any will be deducted for the delayed period i.e. from the month of receipt till the month tax credit is availed, from the running bills.
Penalty amount so determined along with GST if applicable thereon shall be recovered from the contractor.
Any reduction in rate of Tax on any supply of goods or services or the benefit of input tax credit shall be passed on to the recipient by way of commensurate reduction in prices. Bidders have to submit declaration in their bid that they have complied with ‘Anti-profiteering clause’ under GST law.
The bidder’s quoted rates/ price should be after considering the Input Credit under GST law at their end, since GST on output (GST amount charged in Invoice) will be paid by HAL.
In case any changes in taxes and duties as per Gov. Notification (including GST), the same shall be applicable from time to time.
Quarters will be allotted to the awarded agency subject to availability & recommendation from the E-I-C/ O-I-C for which rents as applicable will be recovered from the running bills of the agency.
LIST OF WORK IN PROGRESS FOR THE WORK
Line No.
NAME OF THE CONTRACTOR
HINDUSTAN AERONAUTICS LIMITED KORAPUT DIVISION CENTRAL CONTRACT CELL
Name of the Work
Line No
Name of the Contractor
Check list and acceptance for submission of documents with tender
Constitution and Legal Status of Bidder
Submission of cost of Tender documents by way of DD/BC drawn in favour of HAL, Engine Division, Koraput, payable at SBI, Sunabeda (Scanned image of the same in jpg format only to be uploaded)
Submission of EMD Amount by way of DD/BC drawn in favour of HAL, Engine Division, Koraput, payable at SBI, Sunabeda (Scanned image of the same in jpg format only to be uploaded)
Submission of Banker’s Solvency certificate for an amount as mentioned in tender issued by any nationalized bank issued within a period of 12 months from the final date of submission of tender
Submission of Work order copies for having executed similar works in Govt./ Railways/PSUs/Reputed firms
Submission of Performance / Completion certificates from Govt./Railways/PSUs/Reputed Private Firms (supported with TDS certificate if from Reputed Private firms) in the last 7 years.
For Two works value
For Three works value
Submission of Contractor’s Registration Certificate with Govt./Quasi Govt./PSUs /Reputed Company
Submission of Income Tax Return for last 3 financial years.
Submission of Average Annual financial turnover during the last 5 years
Balance sheet for the last 5 years
Plant and Machinery details of work
Proposed work completion Schedule in the form of Bar Chart
Work in Hand in the required format
Bank Balance Statement for the last three months
Overdraft facilities available with the agencies
Submission of Copy of PF Registration
Submission of Copy of Labour License
Submission of Copy of PAN Card
Acceptance of “General Condition of Contract and Instruction to tenderers” and “Notice Inviting Tender” along
NEFT/RTGS Format Duly filled in (Original to be submitted in the office)
GST REGISTRATION NO:
Submission of Copy of ESI Registration
HINDUSTAN AERONAUTICS LIMITED KORAPUT DIVISION CENTRAL CONTRACT CELL
Name of the Work
Line No
Name of the Contractor
Check list and acceptance for submission of documents with tender
Constitution and Legal Status of Bidder
Submission of cost of Tender documents by way of DD/BC drawn in favour of HAL, Engine Division, Koraput, payable at SBI, Sunabeda (Scanned image of the same in jpg format only to be uploaded)
Submission of EMD Amount by way of DD/BC drawn in favour of HAL, Engine Division, Koraput, payable at SBI, Sunabeda (Scanned image of the same in jpg format only to be uploaded)
Submission of Banker’s Solvency certificate for an amount as mentioned in tender issued by any nationalized bank issued within a period of 12 months from the final date of submission of tender
Submission of Work order copies for having executed similar works in Govt./ Railways/PSUs/Reputed firms
Submission of Performance / Completion certificates from Govt./Railways/PSUs/Reputed Private Firms (supported with TDS certificate if from Reputed Private firms) in the last 7 years.
For Two works value
For Three works value
Submission of Contractor’s Registration Certificate with Govt./Quasi Govt./PSUs /Reputed Company
Submission of Income Tax Return for last 3 financial years.
Submission of Average Annual financial turnover during the last 5 years
Balance sheet for the last 5 years
Plant and Machinery details of work
Proposed work completion Schedule in the form of Bar Chart
Work in Hand in the required format
Bank Balance Statement for the last three months
Overdraft facilities available with the agencies
Submission of Copy of PF Registration
Submission of Copy of Labour License
Submission of Copy of PAN Card
Acceptance of “General Condition of Contract and Instruction to tenderers” and “Notice Inviting Tender” along
NEFT/RTGS Format Duly filled in (Original to be submitted in the office)
GST REGISTRATION NO:
Submission of Copy of ESI Registration
LIST OF WORK IN PROGRESS FOR THE WORK
Line No.
NAME OF THE CONTRACTOR
SCHEDULE-A
HINDUSTAN AERONAUTICS LIMITED
KORAPUT DIVISION
CENTRAL CONTRACT CELL
COMMERCIAL BID
BILL OF QUANTITIES FOR THE WORK OF :- "UPGRADATION OF EXSTING SEWAGE TREATMENT PLANT."
LINE NO : KPTCC/W/390
NAME OF THE AGENCY :
Annexure-A
Manufacturing, supplying & carrying to site all approved materials and fixing in position the distribution arms for rotary distributor system of the existing bio-filter of dia 29.00 mtr. (approx.) DISTRIBUTION ARMS : The work consists of manufacture of Two (2) No’s of fabricated distribution arms, each side of 14.35 mtr. (length) x 0.4 mtr. (width) x 0.3 mtr. (depth) closed Stainless Steel box (Grade S.S 304 of 5mm minimum thickness). The underside of the each arm shall have openings to uniformly distribute the flow of effluents over the bio-filter bed. The distribution arm spreader shall be provided to evenly disperse the flow from each opening. ARM SUPPORTS: The arms shall be supported from the mast by high tension steel tie-rods of required dia. as per design. The fixing of the high tension steel tie-rods with the distribution arms, end attachments shall be made proper with turnbuckles, nuts & bolts etc. The work also includes all necessary activities like dismantling of the existing distribution arms and other structures attached with the existing bio-filter unit & its disposal to the earmarked location, erection & commissioning of the new structures, site fabrications etc. to make the unit fully functional in all respects etc. all complete as per specification and direction of Engineer-in-charge. Manufacturers : Techno Aquatech Pvt Ltd/ Enviro Dyne Systems / Hydro Doc
Design, Engineering, Manufacture, Testing & Supply of Clarifier Mechanisms suitable for existing RCC clarifier tank of 22.0 mtr. dia x 3.5 M Side Wall Depth for primary & secondary clarifiers as per following specifications High Rate Solids Contact Clarifiers (HRSCC)- Major Assemblies are Mentioned as below: − Full Length Bridge/Truss Assembly With Chequered Plate & two layers of high build epoxy coating with primer − Scrapper Drive Assembly & Recirculation Drive Assembly-(MSEP). − Scraper Mechanism - (MSEP) − Impeller and shaft - (MSEP) − Feedwell and Feedwell Cone - (MSEP ) − Detention Zone – (FRP Sheet With MSEP Cage Structure) − Collection Pipe as per site requirement including necessary fittings - (MSEP) − Inlet pipe and Sampling pipe as per site requirement including necessary fittings - (MSEP) − Motor – 415v±10%, 50hz,±5%, 3 Phase, IP-55, Class ‘F’ Insulation, IE2. − Worm Gear Box as per design requirement − All Wetted & Non Wetted Hardware like Nut & Bolts, fasteners etc. In MS Galvanized. The work also includes all necessary activities like dismantling of the existing clarifier unit (complete structure) and its disposal to the earmarked location, erection & commissioning of the complete clarifier unit, site fabrications etc. to make the unit fully functional in all respects. Manufacturers : Techno Aqua Tech Pvt Ltd/ Ion Exchange / Thermax / VA Tech etc. all complete as per specification and direction of Engineer-in-charge.
Supplying, carrying to site all approved materials as per good Engineering practice, designing, Shop Testing including erection & commissioning of Sludge Transfer Pumps Non Clog Self Priming Centrifugal pumps of capacity 27.4 m3/hr at 25 Mtrs of head (3.7KW) along with all necessary accessories i.e, pipe fittings, elbow, flanges, valves etc for Kirloskar Model SP -3L+M or equivalent make, along with Suction Discharge Valves & required MS Piping as per IS 1239. Manufacturer : Kirloskar, Grundfos, Mather & Platt,ITT.
Supplying, carrying to site all approved materials as per the good Engineering practice, designing, shop testing including erection & commissioning of Treated Effluent Feed Pumps, Horizontal Centrifugal Back pullout Pumps of Capacity 150.0 m3/hr at 15 to 20 Mtr head ( 9.3 KW ) along with Suction Strainer, Suction, Discharge Control Valves, NRV and Associated Suction & Discharge piping as per site requirement. The work also includes following Instruments for Feed Pumps: Pressure Gauges ( 6” Dial, 0-10 Kg/cm2 Range, SS Internals Bottom Entry) with Isolation Valves at the Discharge of Each Pump . Make of the Pumps : Kirloskar / Grundfos / Mather & Platt. Make of Butterfly Valves :Tyco/ Fouress/ BDK/ Intervalve/ Del-valve Make of Pressure Gauges : AN Instruments/ WIKA/ General Instruments/Waree
Supply, Erection, Testing & Commissioning of Online Turbidity Analyzer of Range 0 - 100 NTU along with accessories, Sampling provision, Canopy & Supports etc for Monitoring the Turbidity levels at the Outlet of Tertiary Treatment Plant Make: Turbidity Analyzers – FM / E & H / ABB/ Thermo Fischer
Supply, Erection, Testing & Commissioning of PH Analyzer along with accessories, Sample provision, Canopy, Supports etc for Monitoring the pH at the outlet of tertiary Treatment. Make: PH Analyzers – FM / E & H / ABB/ Thermo Fischer
OPEN CHANNEL ULTRA SONIC FLOW TRANSMITTER Supply, Erection & Commissioning of Open Channel Ultra sonic Flow Transmitter along with necessary accessories, Mounting arrangement etc Flow Range : 50 to 1000 m3/hr along rain protection guard. The Ultrasonic Flow Transmitter consist of Ultrasonic Level Monitoring Transmitter & Integrated Flow Meter along with necessary accessories & Mounting arrangements. Approved Make : Forbes Marshall/ E & H/Emerson
Labour charges for dismantling RCC work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 mtrs. lead etc. all complete as per specifications and directions of Engineer-in-charge.
Supplying, providing and laying in position 1:1.5:3 (1 cement : 1.5 coarse sand derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level etc. all complete as per specifications and directions of Engineer-in-charge.
Providing, mixing and applying bonding coat of approved adhesive made up of SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement / Sqm of surface area mixed with specified proportion of approved polymer on chipped portion of RCC as per specifications and directions of Engineer-in-Charge complete in all respects.
Providing, mixing and applying 75mm thick reinforced cement concrete in Grade M 25 with cement content not less than 330 kg per cum, SBR polymer (of approved make @ minimum 2% by wt. of cement used) for modified plain/reinforced cement concrete for structural members having minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness.) as per specifications and directions of Engineer-in-Charge. Rates shall be for finished surface area of concrete and shall include the cost of labour, concrete and appropriate approved Super-Plasticiser for rendering concrete as flowable and SBR polymer but shall exclude cost of reinforcement, bond coat, Shear Keys, centering and shuttering, strutting, propping etc (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument)
Providing, mixing and applying SBR polymer (of approved make) of 12mm average thickness modified cement mortar in proportion of 1:4 (1 cement : 4 graded coarse sand with polymer minimum 2% by weight of cement used) as per specifications and directions of Engineer-in-Charge. Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
Supplying carrying to site all approved materials providing & fixing in position Mild Steel reinforcement bars (TMT bars) conforming to IS 432, cut to length, bent to shape required including cranking, bending spirally for hooping and binding with mild steel wire (annealed) not less than 0.9 m dia for securing with clips. The rate to includes cost of binding wire, cement cover blocks, all cuts and wastes which will not be measured. Only laid weight will be measured including authorized lapse etc. all complete as per specifications and directions of Engineer-in-charge.
Sub total for Annexure-A
Annexure-B
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. (63 mm dia (OD-63 mm & ID-51 mm nominal)
Supplying of following size PVC insulated and PVC sheathed / XLPE Aluminium conductor armoured power cable of 1.1 kV grade etc. as required, Size 4 X 4 Sq mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Size 4 X 4 Sq mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL/ HDPE pipe as required. Size 4 X 4 Sq mm
Sub total of Annexure-B
Sub Total Works Amount
ADD GST @ 18% (( IGST18%) or (CGST @ 9% +SGST@ 9%)), Whichever is applicable
ADD CESS @ 1%
GRAND TOTAL
Note:- The Design of the structures shall be based on good engineering practices and the testing of effluent parameters etc. shall confirm with the compliance requirements of state pollution control board. (a) The design of the sewage treatment plant shall be based on the following design parameters for treatment of effluent. Capacity of the existing sewage treatment plant-2.75 MGD, Flow rate-520m³/hr. (b) Treated water quality parameters:- TSS<25.0 PPM, Turbidity<25.0 NTU
GOODS AND SERVICE TAX (GST)
Bidder should indicate GSTIN No. (Copy of GST registration to be enclosed) and PAN No. (copy of PAN to be enclosed).
Tender will be considered/ accepted, if & only if the vendor has a valid GST Registration No
Central Tax/ State Tax/ Integrated Tax/ Union Territory tax to be quoted as per GST Law
Bidders to ensure correct applicability of Central Tax/ State Tax/ Integrated Tax/ Union Territory tax based on the Inter / Intra state movement Supply of goods and provision services or both
Bidder shall mention the SAC Code/HSN Code for goods and services in accordance with GST law in their Bid and subsequently in their tax invoice. HAL, Koraput Division shall not be responsible for any error in SAC Code/HSN Code for goods and/or services specified by supplier/contractor
The Tax Invoice for supply of Goods & Services should be raised as per the provision of GST Act & Rules and must compulsorily mention the following
a. HAL, Korpaut Division GST registration number as 21AAACH3641R1ZJ
b. Name & address of supplier / Vendor/ Contractors
c. GSTIN of Supplier / vendors / Contractors
d. Consecutive Serial Number & date of issue
e. Description of goods or services
f. Total value of supply
g. Taxable value of supply
h. Tax Rate – Central Tax & State Tax or Integrated Tax, Cess
i. Amount of Tax charged
j. Place of supply
k. Address of delivery if different from place of supply
l. Signature of authorized signatory
Reimbursement of GST to the vendor is contingent upon complying with the following condition by the service provider
i. Uploading the (invoices raised on HAL, KoraputDivision ) onward GST Return (GSTR-1) in GSTN Network portal within the statutory time period
ii. Discharging the GST tax liability to the Government.
iii. Submission of Tax Invoice to HAL, Korpaut Division.
iv. Submission of proof of payment of GST to HAL, Korpaut Division.
v. Receipt of goods / services by HAL Koraput Division.
vi. Availment of Input Tax Credit by HAL, Korpaut Division .
In case GST credit is delayed/ denied to HAL, Korpaut Division, due to non/delayed receipt of goods and/or services and/or tax invoice or expiry of timeline prescribed in GST Law for availing such ITC, or any other reason not attributable to HAL, Korpaut Division, GST amount shall be recoverable from Vendor along with interest & penalty levied/ leviable on HAL, Korpaut Division, as the case may be
In case vendor delays declaring such invoice in his return and GST credit availed by HAL, Korpaut Division is denied or reversed subsequently as per GST law, GST amount paid by HAL, Korpaut Division towards such ITC reversal as per GST law shall be recoverable from vendor/contractor along with interest & penalty levied/ leviable on HAL, Korpaut Division.
In case of discrepancy in the data uploaded by supplier in the GSTN portal or in case of any incomplete work/service, then HAL, Korpaut Division will not be able to avail the tax credit and will notify the supplier of the same. Supplier has to rectify the data discrepancy in the GSTN portal or issue credit note (details to be uploaded in GSTN portal).
For any such delay in availing of tax credit for reasons attributable to vendor (as mentioned above), interest as per the GST Act & Rules, along with penalty, if any will be deducted for the delayed period i.e. from the month of receipt till the month tax credit is availed, from the running bills.
Penalty amount so determined along with GST if applicable thereon shall be recovered from the contractor.
Any reduction in rate of Tax on any supply of goods or services or the benefit of input tax credit shall be passed on to the recipient by way of commensurate reduction in prices. Bidders have to submit declaration in their bid that they have complied with ‘Anti-profiteering clause’ under GST law.
The bidder’s quoted rates/ price should be after considering the Input Credit under GST law at their end, since GST on output (GST amount charged in Invoice) will be paid by HAL.
In case any changes in taxes and duties as per Gov. Notification (including GST), the same shall be applicable from time to time.
Quarters will be allotted to the awarded agency subject to availability & recommendation from the E-I-C/ O-I-C for which rents as applicable will be recovered from the running bills of the agency.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
raw.json
RAW_JSON
3.AM.pdf
TENDER_DOCUMENT • 5.21 MB
1.NIT08.pdf
TENDER_DOCUMENT • 1.60 MB
2.NEWGCC2023.pdf
TENDER_DOCUMENT • 2.92 MB
25.SOW384.pdf
TENDER_DOCUMENT • 0.07 MB
26-1.CBID384.xlsm
TENDER_DOCUMENT • 0.07 MB
21-2.WIP390.xls
TENDER_DOCUMENT • 0.03 MB
UNDERTAKING.pdf
TENDER_DOCUMENT • 0.04 MB
22-1.CL384.xls
TENDER_DOCUMENT • 0.06 MB
4-1.BOQ384.pdf
TENDER_DOCUMENT • 0.25 MB
UNPRICED390.pdf
TENDER_DOCUMENT • 0.12 MB
22-2.CL390.xls
TENDER_DOCUMENT • 0.06 MB
15.EPS.pdf
TENDER_DOCUMENT • 0.02 MB
15.EPS_2.pdf
TENDER_DOCUMENT • 0.02 MB
14.UNDERTAKING.pdf
TENDER_DOCUMENT • 0.01 MB
21-1.WIP384.xls
TENDER_DOCUMENT • 0.03 MB
PBO390.xlsm
TENDER_DOCUMENT • 0.05 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .