REPAIR MAINT OF JOINERY SANITARY FITTINGS PLUMBING ROOF TREATMENT AND ALLIED WORKS UNDER ZONE II OUTSIDE FORT WILLIAM UNDER GE(FW) KOLKATA

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick below or above GL complete all as specified and directed.

Dismantling stone slabs and tiles, laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as a specified and as directed

Dismantling of Asbestos cement corrugated, semi-corrugated sheet in roof covering complete all as a specified and as directed

Dismantling of plain or corrugated steel sheeting any gauge or any thickness in roof covering including stacking serviceable materials of re-use and removing unserviceable materials complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions arches pillars etc but excluding ashlars facing,dressed stone work and precast concrete articles complete all as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key and scrubbing down with water complete All as specified and as directed.

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing tiles from site and rubbish off the premises complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area n.exc. 1.5 Sqm each all as directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n.exc.4.00 Sqm each wooden all as directed.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 Sqm each all as directed.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 Sqm each and re-fixing in the same opening after necessary repair like easing, etc complete all as specified and directed.

S&F for 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, moulded or chamfered, put together with glue, pinned at joints complete all as directed.

S&F 30mm flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick Factory made 2nd class hard wood glazed & skleton shutters, open rebated and prepared to received glass, gauge etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(a) complete all as specified and directed.

S&F Factory made 35mm thick with 2nd class hard wood, rail and style factory made plain framed panelled shutter(two panel) with lock, rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS:1003(Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F PVC solid door frame of size 50 x 47 mm made out of 5 mm thick prelaminated single side PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F 30 mm thick factory made both side prelaminated solid panel PVC door shutter consisting of frame made out of MS tube of 19 gauge thickness and size of 19mm X 19mm for stiles, top and bottom rails, treated with a coat of metal primer, MS frame covered with heat moulded prelaminated PVC 'C' channel for stiles and both side prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; stiles and rails feathered at edges, panelling of both side prelaminated PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in frame complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium doors frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium doors shutters, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips rubber neoprene packing, handles 2 Nos in each door, hinges, Mortice lock vertical type size 100 mm 4 levers of brass in each door, anodised aluminium snap beading screws etc as per manufactures instruction complete all as specified. (NOTE: Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle, mortise lock etc as described in item. Sheet glass shall be measured seperately)

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, anodised aluminum fittings such as suitable 150 mm long peg stays (01 No), hinges type B-21 100 mm long (02 Nos), suitable handle-01No each shutter etc as per manufactures instruction complete all as specified and directed. (NOTE: Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle etc as described in item. Sheet glass shall be measured seperately)

S&F in repair anodised aluminium grill (anodised transperent or dyed to required IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard design/pattern, with approved standard section and fixed to the existing window frame with chromium plated brass screws/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as per requirement and as specified and directed.

S&F 5.5 mm thick plain tinted sheet glass for Aluminium door/partition/ window complete all as specified and as directed.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

S&F in repair aluminium anodised door frame size 100mmX63mmX2mm thick and shutter size 50mmX45mmX2mm thick as in top rail & style and 100mmX45mmX2mm thick in bottom & lock rail including complete fittings and fixtures and mortice lock, 'D' type handles, hydraulic door closer and 5 mm thick glass complete all as specified and directed

S&F in repair aluminium, anodised partition with frame of size 63X38X2mm thick and fixing hold fast with snap beading, neoprene gasket etc complete all as specified and directed. (NOTE: Glass/boarding for partition shall be measured and paid seperately)

S&F anodised powder coated (minimum thickness of powder coating 50 micron) aluminium frame (size 92.36mm x 29.70mm x 1.50 mm thick channel size 30.10 mm) @ 1.22 kg/RM (three track) for doors, windows & ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified and directed.

Hacking out old broken glass (any thickness and size or quality) from wooden frames glazed with putty or fixed with beads complete all as specified and directed.

. - ditto - all asper item No. 28 here-in-before, but from metal frame.

S&F anodised powder coated (minimum thickness of powder coating 50 micron) aluminium window shutter (size 41mm x 20mm x 1.60 mm thick railing size 20 mm) @ 0.50 kg/RM for doors, windows & ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified and directed. (NOTE: Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, sheet glass, handle etc as described in item. Glass shall be measured and paid seperately)

S&F steel window with side hung shutter including necessary hinges with steel handle and steel peg stay complete with glazing bars devotailed or welded all as directed. (NOTE: Sheet glass will be measured and paid seperately)

S&F stainless steel wire cloth, 0.65mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

. - ditto - all as per item No. 29 here-in-before, but fixed in repair.

S&F 3mm thick ordinary quality plain sheet glass glass and glazing in square n.exc. 0.5 Sqm in each pane complete all as specified and directed.

-ditto- but in metal frames with oil putty

S&F 3mm thick ordinary quality frosted sheet glass glass and glazing in square n.exc. 0.5 Sqm in each pane complete all as specified and directed.

-ditto- but frosted glass in metal frames with oil putty

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

- ditto - all as per item No. 39 here-in-before, but 200mm long all as directed complete all as specified and directed.

S&F 300mm aluminium, anodised sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as directed complete all as specified and directed.

- ditto - all as per item No. 41 here-in-before, but fixed in repair.

S&F 100mm butt hinges stainless steel medium weight complete all as specified and directed.

- ditto - all as per item No. 43 here-in-before, but 75mm.

S&F aluminium handle, cast type anodised 125mm size complete all as specified and directed.

- ditto - all as per item No. 45 here-in-before, but 150mm.

S&F 20mm dia fancy type chrominum plated drapery rod incl heavy duty decorative bracket and all fittings fixed on wall sample as approved by Engr-in-charge complete all as specified and directed. (Note: Quoted rate shall be deemed to be inclusive of the cost of brackets)

M&L in repair 19/20mm thick pre-laminated particle board as in cup board shutter double leaf one side decorative shade lamination and other side balancing white lamination. All edges properly sealed with 5mm thick 2nd class hardwood beading fixed with water resistant adhesive except rebate side which shall be of 25mm thick complete all as specified and directed.

S&F in repair aluminium (extruded section) body door closer, hydraulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000 in width and weight between 61Kg to 80 Kg and fixed complete all as specified and directed.

S&F in repair drawer knobs 40 mm dia of brass polished fixed with nut screw and washer complete all as specified and directed.

S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass, other part made of mild steel heavy duty complete all as specified and directed.

S&F in repair for 300mm brass ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repair 2mm thick fibre glass reinforced transluent corrugated or plain coloured/printed sheeting with two corugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

M&L for 18 to 20 mm thick black/coloured granite machine cut laid over 10mm thick screed bed in cement mortar 1:4 and jointed with grey or coloured cement to match with admixture of pigment to match the shade of granite including cutting polishing complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type 'C-2' (using 40mm graded crushed stone aggregate) as in sub base of concrete finished even and fair cement complete all as directed..

M&L for 75mm thick PCC (1:3:6) type 'C-2' (using 40mm graded crushed stone aggregate) as in floor, plinth protection etc, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type 'B-1' (using 20mm graded crushed stone aggregate) as in floor finished fair and even complete all as a specified and as directed

M&L mild steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS-1161:2014 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

S&F plates (plain or chequered) channels, square cut or notched (ordninary and counter sunk) forming holes, without any attachment all as specified rolled mild steel in stairs ( framed) including stringers, treades landing, balusters, hand rails etc including cleats, brackets etc complete all as specified and as direceted.

M & L for 6 mm thick asbestos cement, corrugated sheet in roof, wall fixed with L type or J type hook complete all as a specified and as directed

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

-ditto- but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter of roof.

M&L brick work with sub class'B' fly-ash bricks, straight or curved on plan exc 6m radius buit in cement mortar 1:6 complete all as a specified and as directed.

M&L for brick work with fly ash brick straight or cuved on plan to any radius in half bricks thick walls, built in 1:4 cement mortar complete all as directed.

M&L 15mm thick rendering on brick or concrete walls in cement mortar 1:6 finished evean smooth without using extra cement complete all as a specified and as directed

M&L 15 mm thick rendering on fair faces of brick work in cement mortar 1:4, finished even and fair complete all as a specified and as directed

M&L 5mm thick rendering on ceiling surfaces in cement mortar 1:3 , finishing even and smooth without using extra cement including necessary scaffolding complete all as a specified and as directed

M&L Non Skid joint free coloured tiles 8-9 mm thick, area of each tiles exc 0.11 sqm but n.exc 0.18sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl 15mm thick screed bedding in cement mortar 1:4 complete all as a specified and as directed

M&L Non Skid joint free coloured tiles 7-8mm thick area of each tiles exc 0.06Sqm but n. exc 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl 15mm thick screed bedding in cement mortar 1:4 complete all as a specified and as directed

M&L coloured glazed ceramic tiles in vertical surfaces 450X300X7-8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match, fixed over and incl 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M&L Vitrified ceramic coloured (light shade) tiles, 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade laid over and incl screed bed 20mm thick cement mortar 1:4 complete all as a specified and as directed

Removal of existing water proof treatment of any description from roof surface including cement plaster/screed bed carefully from the surfaces, roughening concrete surfaces and cleaning the roof surfaces by brushing, sweeping and scrubbing down with water and removal of debris complete all as specified and as directed.

M&L for brushing cement slurry @ 2.75 Kg/sqm over cleaned roof surface prior to application of concrete complete all as directed by Engineer - in - charge .

M&L for 25 mm thick Cement Concrete, Type B-0, 1:2:4 (using 12.50 mm graded Stone aggregate), as in roof padding, finished even and fair complete all as specified and directed.

M&L 10 mm thick screed bed in cement mortar 1:3 over roof mixed with water proofing compound as per manufacturer's instruction complete all as specified and directed. (NOTE: WPC will be measured and paid separately)

Supply only liquid water proofing compound all as specified and as directed.

M&L for water proofing treatment on existing cleaned RCC roof with the following specifications and manufacturer's instruction complete all as specified and directed :- (i) Preparing and cleaning of fully dried surfaces as per IS 3067-1966. (ii) Applying bitumen primer conforming to IS:3384-1968 over the cleaned base @ 0.50 litre per sqm. (iii) Providing a layer of 3 mm thick APP modified pre-fabricated five layer, weight not less than 3.6 kg/sqm, black finished reinforced with non-woven polyster matt membrane with butane torch application. Overlap shall be minimum 100 mm on the transverse direction and 75 mm on longitudinal direction. (iv) Applying two coats of bitumen based UV reflective paint with aluminium finish @ 0.10 litre per sqm over APP membrane. (v) Sealing of all angles & abutments upstands with extra care to ensure perfect bondage. Sealing of edges well into grooves & protect the seal with a polysulphide/polyurethane sealant.

M&L mild steel bands and straps support or stays holdfast and similar articles conforming complete all as specified and directed.

S&F in repair PVC solid wall lining consisting of 5 mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per manufacturer’s specification and instruction and as directed.

S&F in repair 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing.

S&F in repair false ceiling with 'E' board "Classic", reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium snap grid to support the boards/files with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides, fixed to ceiling with hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long and applying one coat of acrylic distemper over a coat of primer on exposed surfaces complete all as specified and as directed. (NOTE: Quoted rate shall be deemed to be inclusive of the cost of ceiling board)

S&F in repair 'E' board "Classic", reinforced, designer series, ceiling board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on existing snap grid system and applying one coat of acrylic distemper over a coat of primer on exposed surfaces complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tounge, anodised, with hard drawn steel spring, fixed in floor. 150mm overall length of cover plate complete all as a specified and as directed

S&F in repair Chromium plated brass Pillar tap (normal range), fancy type. with areator, fixed to wash hand basin, complete all as specified and directed. (Make : ESS ESS, Cat No: RO-101 / PRAYAG, Cat No: 6702 / Essco, Cat No: SQT-507KN / SOMANY, Model: ETHER)

S&F in repairs Chromium plated brass Pillar tap (premium range), fancy type. with areator, fixed to wash hand basin, complete all as specified and directed. (Make : JAQUAR, Cat No: ARI-39011 / CERA, Cat No: F1005101/ ASIAN PAINTS, Cat No: MYPC101 / HINDWARE, Cat No: F360001 / PRAYAG, Cat No: 8102 / PARRYWARE, Cat No: T3802A1)

S&F in repair swan neck pillar cock (normal range), 15mm dia chromium plated cast copper alloy with round spout left hand knob operating screwed for iron pipe etc complete all as directed (MAKE :Essco, Cat No : SQT-510KN / ESS ESS, Cat No: T-113 / PRAYAG, Cat No : 7214/ SOMANY, Model: ETHER)

S&F in repair swan neck pillar cock (premium range), 15mm dia chromium plated cast copper alloy with round spout, sink mounted type, screwed for iron pipe etc complete all as directed (MAKE :PARRYWARE, Cat No : G4803A1 / CERA, Cat No: F1003104 / PRAYAG, Cat No : 9014/ HINDWARE, Cat No: F280012 / ESS ESS, Cat No: PT-19 / JAQUAR, Cat No: SOL-6357)

S&F 15mm bore chromium plated central hole basin mixer (normal range) without popup waste system with 450mm long copper pipe and brass nut, complete all as specified and directed. (MAKE : Essco, Cat No: SQT-516KN / ESS ESS, Cat No : T-118 / PRAYAG, Cat No: 7250 / SOMANY, Model: ETHER)

S&F in repair 15mm bore chromium plated single lever central hole basin mixer (premium range) without popup waste system with 450mm long copper pipe and brass nut, complete all as specified and directed. (MAKE : JAQUAR, Cat No: ARI-39001B / CERA, Cat No : F1005451 / ASIAN PAINT, Cat No: MYBM101 / HINDWARE, Cat No: F360011/ PRAYAG, Cat No: 8151 /PARRYWARE, Cat No: T3814A1)

S&F in repair Chromium plated brass Bib cock with wall flange (normal range), fancy type, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : Ess Ess, Cat No: RB-103 / PRAYAG, Cat No: 6706 / Essco, Cat No: SQT-512KN / / /SOMANY, Model: ETHER)

S&F in repair Chromium plated brass Bib cock with wall flange (premium range), fancy type, long body, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: ARI-39037/ CERA, Cat No: F1005151 / ASIAN PAINTS, Cat No: MYBC101 / PRAYAG, Cat No: 8108 / HINDWARE, Cat No: F390003 / PARRYWARE, Cat No: G1434A1)

S&F in repair 15mm bore chromium plated two way bib cock with flange (normal range), fancy type as directed. (Make : Essco, Cat No: SQT-512ANKN / Ess Ess, Cat No: T-105E / PRAYAG, Cat No: 7211 / SOMANY, Model: ETHER)

S&F in repair 15mm bore chromium plated two way bib cock with flange (premium range), fancy type complete all as specified and as directed. (Make : JAQUAR, Cat No: CON-041KN / CERA, Cat No: F1005161 / ASIAN PAINTS, Cat No: MYBC102 / PRAYAG, Cat No: 8111 / HINDWARE, Cat No: F390004 / PARRYWARE, Cat No: G1434A1)

S&F in repair, 15 mm bore fancy type stop valves, cast copper alloy, chromium plated (concealed type), screwed down, high pressure, with crutch or butterfly handle, incl concealed body, screwed both ends for iron pipe or for unions and, complete all as specified and directed. (MAKE :Essco, Cat No: SQT-514AN / Ess Ess, Cat No: T-332B / PRAYAG, Cat No :7218 / SOMANY, Model: ETHER)

S&F in repair Chromium plated brass Angular stop cock (normal range), fancy type, concealed type with wall flange fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make :Essco, Cat No: SQT-526KN / ESS ESS, Cat No: T-112A / PRAYAG, Cat No: 7210 / SOMANY, Model: ETHER)

S&F in repair angle valve (premium range), 15 mm bore, cast copper alloy, chromium plated fancy type, concealed type with wall flange fixed to iron pipe complete all as specified and directed. (Make : PARRYWARE, Cat No: G4807A1 / JAQUAR, Cat No: FUS-29053 / CERA, Cat No: F1015361 / ASIAN PAINTS, ALAC101 / HINDWARE, Cat No: F390005 / PRAYAG, Cat No: 9010)

S&F in repair chromium plated brass over head shower rose with arm (normal range), with 3 flow, fixed to 15mm bore of iron pipe complete all as specified and directed. (Make : Essco, Cat No: ALE-536A & EOS-542N / ESS ESS, Cat No: SA-101 & OH-202 / PRAYAG, Cat No: BS-73 / SOMANY, Model: ETHER)

S&F in repair chromium plated brass over head shower rose with arm (premiuml range), with 3 flow, fixed to 15mm bore of iron pipe complete all as specified and directed. (Make : CERA, Cat No: F7040103 (for arm) & F7020305 (for shower) / PARRYWARE, Cat No: T9802A1 (for arm) & T9986A1 (for shower)/ HINDWARE, Cat No: F160051)

S&F in repair Chromium plated brass Wall mixer, concealed type, with concealed body, with overhead shower arrangement fixed with 15 mm bore Iron pipe including taking down existing mixer complete all as specified and directed. (Make : JAQUAR, Cat No : FUS-29273UPR / PARRYWARE, Cat No: G4816A1 / CERA, Cat No: F1003401 / ASIAN PAINTS, Cat No: ALWM103 / PRAYAG, Cat No: 9375-N / HINDWARE, Cat No: F390020)

S&F in repair Chromium plated brass Wall mixer, concealed type incl concealed body, with both overhead and telephone shower arrangement, fixed with 15 mm bore Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No : FUS-29281/ PARRYWARE, Cat No: G4817A1 / CERA, Cat No: F1003403 / ASIAN PAINTS, Cat No: ALWM104 / PRAYAG, Cat No: 9380-N / HINDWARE, Cat No: F390022) NOTE: Telephone shower shall be measured and paid seperately.

S&F in repair fancy type chromium plated telephonic hand shower (ABS Body), multiflow type with flexible tube and hook screwed for iron pipe including frame complete all as specified and directed. (Make : JAQUAR, Cat No: HSH-1939 / CERA, Cat No: F7030103AB / ASIAN PAINTS, Cat No: HS-104 / HINDWARE, Cat No: F160050 / PRAYAG, Cat No: BHS-90 /PARRYWARE, Cat No: T9819A1 )

S&F chromium plated brass jet spray with one metre PVC tube complete all as specified and directed . (Make : Essco, Cat No ALE-547/PRAYAG, Cat No: BEA-17 / JAINKO, Cat No: JSJ-1)

S&F in repair chromium plated Hand shower (health faucet), ABS body (normal range) with 1.0 metre long flexible tube in chrome finish with wall hook complete all as specified and directed. (MAKE : Essco, Cat No : ALE-ESS-583/ ESS ESS, Cat No : C-232Y /PRAYAG, Cat No: BEA-100 / SOMANY, Model: ETHER)

S&F in repair chromium plated Hand shower (health faucet), ABS body (premium range) with 1.2 metre long flexible tube in chrome finish with wall hook complete all as specified and directed. (MAKE : JAQUAR, Cat No: PRS-031/ CERA, Cat No: F8030401AB / ASIAN PAINTS, Cat No: C-232N / HINDWARE, Cat No: F160013 / PARRYWARE, Cat No: E8352A1)

S&F in repair Chromium plated brass Towel ring (premiuml range) complete all as specified and directed. (Make : Essco, Cat No: AEC-1121 / PRAYAG, Cat No: BA-02 / ESS ESS, Cat No: AC-702 / SOMANY, Model: ETHER)

S&F in repairs, Tubular towel rail (normal range), 20mm dia, 600 mm long between flanges incl brass chromium plated, complete all as specified and directed. (MAKE : Essco, Cat No : AEC-1111 / PRAYAG, CaT No: BA-40 / ESS ESS, Cat No : AC-701 / SOMANY, Model: ETHER)

S&F in repair 6 mm thick bevelled edge mirror of size as required fixed on 5 mm thick plywood or acrylic sheet board backing, fixed with chromium plated screws and cup washer complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick in kitchen with plug washers, waste coupling, PVC waste pipe and fixing cantilever brackets connecting union to pipe, overall size of sink 914 mm x 460 mm and bowl size 405 mm x 354 mm x 203 mm complete complete all as specified and directed. (MAKE : CERA, Cat No: B4512201 /PRAYAG, Cat No. 1339D / PARRYWARE, Cat No: C855099 or equivalent model in NIRALI / ANJALI / JAYNA) (NOTE: Waste coupling and Waste pipe shall be measured and paid seperately)

S&F in repair 32 mm bore PVC corrugated waste pipe, 800 mm long for wash hand basins, sinks etc complete all as specified and directed. (Make: PRAYAG, Cat No: 327 or equivalent make as spproved by GE)

S&F in repair 32 mm bore PVC collapsible waste pipe, 800 mm long complete all as specified and directed. (Make: PRAYAG, Cat No: 3272 or equivalent make as spproved by GE)

S&F in repair strainer for kitchen sinks, round, complete all as specified and directed. (Make: PRAYAG, Cat No: SA-03 or equivalent item as approved by GE)

S&F in repair chromium plated brass waste coupling, 32 mm size, full threaded complete all as specified and directed. (Make: PRAYAG, Cat No: BEA-11 / ESS ESS, Cat No: C-230C / ESSCO, Cat No: ALE-544NT)

S&F in repair 32mm CP Waste coupling (half threaded) complete all as specified and directed. (MAKE : PRAYAG, Cat No: BEA-10 / ESS ESS, Cat No: C-230H / ESSCO, Cat No: ALE-543HT)

S&F in repair 32mm Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and directed. (Make: PRAYAG, Cat No: 103 or equivalent model in JEXON / POLYTUF / SHAKTI)

S&F in repair Stainless steel kitchen rack of size 31" x 24" x 10" fixed in wall with screws and washer including taking down existing rack complete all as specified and directed. (MAKE : PRAYAG, Cat No : P-340 or equivalent model in SUYOG / BLUE STAR / ANUPAM INDUSTRIES)

S&F in repair CP grating 100mm size fixed with white cemnt complete all as directed. (Make : PRAYAG, Cat No : FT-62 or equivalent make as approved by GE)

S&F in repair acrylic bathroom cabinet box with mirror of size 622 mm X 422 mm size complete all as specified and directed. (MAKE: PRAYAG, Cat No: 555 or equivalent model in POLYTUF / JEXON / SHAKTI / NILKAMAL )

S&F corner glass shelf 300 mm with brass brackets, as in repair complete all as specified and directed. (Make: PRAYAG, Cat No: BEA-44 / JAQUAR, Cat No: ACN-1173 / PARRYWARE, Cat No: T6010A1 / CERA, Cat No: F5005102)

S&F in repairs Low density polythelene pipe connection, comprising of 15 mm dia 450 mm long having PTMT union at each end complete all as specified and directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 / ESS ESS, Cat No: B2CH118 or equivalent model in SHAKTI / JEXON)

S&F in repair 15mm bore heavy duty PVC connector pipe of length 600mm with PTMT coupling at both ends, screwed down for pipe as directed. (MAKE : PRAYAG, Cat No. 324 / POLYTUF, Cat No. 4004-D / SHAKTI, Cat No: SB 1324-D)

S&F CP bottle trap with internal portion 32mm size with 190mm long wall connection pipe complete all as specified and directed (Make: Essco, Cat No: ALE-773AL190X125 / ESS ESS, Cat No: C-231C / PRAYAG, cat No: BEA-26 / SOMANY, Model: ETHER)

S&F in repair coloured (any) PVC seat cover for EWC of any description with hinging device complete all as specified and directed.

-ditto- but white seat cover for EWC

S&F in repair White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type with Inlet, Ball Valve, Float, flush pipe and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed including taking down/out unserviceable Flushing Cistern and connected items complete all as specified and directed. (MAKE : PARRYWARE, Model : Slim line Economy / HINDWARE, Model : Sleek Plus / CERA, Model : Corona / PRAYAG, Model: SMART or equivalent model in COMMANDER )

Repair only to PVC flushing cistern incl cleaning and replacement of washer and syphonage of suitable size if required complete all as specified and directed.

Repair only to vitreous china flushing cistern in coupled/one piece closet incl cleaning and replacement of washer and syphonage of suitable size if required complete all as specified and directed.

S&F in repairs vitreous china (coloured) wash down water closet pan (pedestal pattern) with 'P' or 'S' trap front or back inlet, fixing bolts (except flushing cistern and flush pipe) incl plastic water closet seat cover (white) and mild steel chromium plated or aluminium hinging device complete all as specified and directed. (Make : Parryware, Model : Elite / JAQUAR, Model: Continental / CERA, Model: Conventional / HINDWARE, Model: SLICK)

S&F in repair vitreous china floor mounted one piece closet (Pedestal pattern), white including vitreous china valveless syphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, PVC soft close seat cover and connecting fittings complete all as specified and directed. (Make : CERA, Model: CHAMP / PARRYWARE, Model: Entice / HINDWARE, Model: FLORA / ASIAN PAINTS, Model: IMMERSE )

S&F vitreous china floor mounted coupled closet (Pedestal pattern) white including low level vitreous china valveless syphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, PVC white soft close seat cover and connecting fittings complete all as specified and directed. (Make :CERA, Model : CLAIR DELUXE / PARRYWARE, Model: CASCADE NXT / JAQUAR, Model: FONTE / HINDWARE, Model: CONSTELLATION PREMIUM)

S&F in repair vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including making good to floor, complete all as specified and directed. (MAKE : CERA, Cat No: S3010109 / HINDWARE, Cat No. 20042 /ASIAN PAINTS, Cat No: WM-32-X / PARRYWARE, Cat No: C0126)

S&F in repair Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and directed. (Make of WHB : PARRYWARE, Model: FLAIR / HINDWARE, Model: MARIO / JAQUAR, Model: CONTINENTAL / CERA, Model: CLAIR) (NOTE: Waste coupling and Waste pipe shall be measured and paid seperately)

S&F in repair tubes 15mm bore medium grade galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

-ditto all as per item No 133 here-in-before but 20 mm bore

-ditto all as per item No 133 here-in-before but 25 mm bore

Taking down and re-fixing old steel tubing 15mm bore and connection in new or old position(wall, ceiling, floor etc.) complete all as specified and directed.

-ditto all as per item No 136 here-in-before but 20 mm bore

-ditto all as per item No 136 here-in-before but 25 mm bore

Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing unsv tank complete all as specified and directed.

- ditto - all as per item No 139 here-in-before but 2000 ltrs capacity.

- ditto - all as per item No 139 here-in-before but 500 ltrs capacity.

S&F in repair 20 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-152 or equivalent model in JEXON / POLYTUF / SHAKTI)

All as per Item No. 142 here-in-before but 25 mm bore Ball brass valves. (MAKE : PRAYAG, Cat No. B-153 or equivalent model in JEXON / POLYTUF / SHAKTI)

S&F in repair PVC tank cover for 500 Ltrs PVC Tank complete all as specified and directed.

S&F in repair PVC tank cover for 1000 Ltrs PVC Tank complete all as specified and directed.

S&F in repair PVC tank cover for 2000 Ltrs PVC Tank complete all as specified and directed.

Disconnecting existing water storage Tank of capacity exceeding 1000 litres but not exceeding 2000 liters for cleaning of water tank, removing of mud, sludge etc and flushing with chlorine water including supply and fixing of any damaged accessories for water Tank and writting MES No, Unit Name (With capital letter, not exceeding 15cm height and not exceeding 10ms each tank ) and re-connecting and refixing all connections complete all as specified and directed.

Disconnecting existing water storage Tank of capacity exceeding 500 litres but not exceeding 1000 liters for cleaning of water tank, removing of mud, sludge etc and flushing with chlorine water including supply and fixing of any damaged accessories for water Tank and writting MES No, Unit Name (With capital letter, not exceeding 15cm height and not exceeding 10ms each tank ) and re-connecting and refixing all connections complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, 100 mm bore, jointed in cement mortar and taking out of trenches, complete all as specified and directed.

S&F Cast iron (sand cast) soil, waste and vent pipes 100 mm bore of any length with or without ears with cement joints all as specified laid in trenches or in floors complete all as specified and directed.

-ditto- but pipes fixed on walls

S&F CI bends for 100mm pipe (any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed.

S&F CI bends of 100mm dia with ducks foot or heel rest (ISI Marked) complete all as specified and directed.

S&F CI branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parellel branches, for 100mm dia pipe complete all as specified and directed.

S&F 100mm bore cast iron cowls complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

M&L for taking down plants/vegetaion from wall upto roof level by means of cutting holes into brick wall and making good the surfaces of dismantling portion n.exc 150Sqcm superficial area and n.exc on brick deep by PCC 1:3:6 type C1 (using 20 mm graded stone aggregates) and plastering in cement mortar (1:4) of disturb portion and applying two coats of cement based paint over a coat of primer to match the existing surfaces height upto 4th floor incl necessary scaffolding etc complete all as specified and directed.

-ditto- all as per item No 161 but for height 5th to 8th floor.

-ditto- all as per item No 161 but for height exc 8th floor.

Preparing new surface of wood or wood based material of any description and in any position not otherwise described n.exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of wood primer complete all as directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, treating ends of posts, back of chowkhats etc, with tar or coal tar black paint, area tarred exc 0.1 sqm but n. exc 0.5 sqm each complete all as specified and directed.

-ditto- but treating small articles such as holdfasts, ends of posts, back of chowkhats, etc, area n exc 0.1 sqm each

M&L for applying one coat of acrylic distemper, finished with rollers to old decorated surfaces of wall including preparation surfaces (by brooming down steel wire brushing scrapping down smoke soot, moulds, moss, effoloresent, salts trading oil and greasy spots etc) complete all as specified and directed.

M&L for applying one coat of acrylic distemper, finished with rollers to old decorated surfaces of ceiling including preparation surfaces complete all as specified and as directed.

M&L for complete removal of existing treatment of wall surfaces and applying two coats of acrylic distemper, finished with rollers over a coat of alkali resistant primer applied over 1.0 mm thick wall putty complete all as specified and directed.

M&L for applying one coat of synthetic enamal paint on old treated wooden surfaces of any description over 10cm width or girth including cleaning and preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for applying one coat of synthetic enamal paint on old treated steel surfaces of any description over 10cm width or girth including cleaning and preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for applying one or more coat of French polish on old treated wooden surfaces of any description over 10cm width or girth including cleaning and preparation of surfaces complete all as directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and applying two coats of plastic/acrylic emulsion paint, finished with rollers over a coat of suitable primer applied over 1.0 mm thick wall putty complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint with brush over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of old decorated wall surfaces and applying one coat of cement base paint with brush complete all as specified and directed.

M&L for preparation of new surfaces of walls and soffit of chajja, roof slab etc., by cleaning, brooming, rubbing and scrapping as required using broom, emery paper, putty blade/scraper as applicable to make the surface free from protrutions, loose particles, dust etc including necessary safety & protective measures such as safety belt, headgear etc, finishing the surface with 2 mm thick exterior wall putty (in two layers) for smooth finish and finishing with two coats of weather proof exterior emulsion paint over a coat of suitable exterior primer of approved make using airless spray technology capable of operating single spray gun with hose of adequate length and necessary scaffolding for upto 4 storey building height complete all as specified and directed.

M&L for preparation of old treated/painted surfaces of walls and soffit of chajja, roof slab etc., by cleaning, brooming, rubbing and scrapping as required using broom, emery paper, putty blade/scraper as applicable to make the surface free from loose paint, algae formation, dust etc including necessary safety & protective measures such as safety belt, headgear etc including filling cracks upto 5mm with and including suitable elastomeric crackfill paste and applying one coat of weather proof exterior emulsion paint of approved make using airless spray technology capable of operating single spray gun with hose of adequate length and necessary scaffolding for upto 4 storey building height complete all as specified and directed.

M&L for complete removal of existing treatment on old painted surfaces of walls and soffit of chajja, roof slab etc. by using high pressure jet washer including cleaning the surface by scrapping as required using emery paper, putty blade/scraper as applicable for removing loose paint, corrosion, algae formation etc., to make the surface clean and free from dust, for upto 4 storey height including necessary scaffolding, safety and protective measures complete all as specified and directed.

M&L for complete removal of existing treatment on old painted surfaces of walls and soffit of chajja, roof slab etc. by scrapping and removing treated surfaces with mechanical wall sander (having vacuum mechanism for suction) having minimum 1500 RPM, sanding pad of 80 grit size having 7"- 9" dia (as required) including cleaning, watering to make the surface clean and free from dust, for upto 4 storey building height including necessary scaffolding, safety and protective measures complete all as specified and directed.

M&L for applying 2mm thick wall care putty (in two layers) on old cleaned surfaces of walls, soffits of chajja, roof slab etc, for smooth finish and finishing with two coats of weather proof exterior emulsion paint over a coat of suitable exterior primer of approved make using airless spray technology capable of operating single spray gun with hose of adequate length for upto 4 storey building height including necessary scaffolding, safety and protective measures complete all as specified and directed.

M&L Preparing new Surfaces of wall and applying Three coats of white wash complete all as specified and as directed.

M&L for repair to steel window including welding, binding of steel section, repair to hinges, fixing of stay and handles etc n.exc 1.5 sqm complete all as specified and directed.

Ditto as per item No. 182 above but area exc 1.5sqm but n.exc 4.00sqm complete all as specified and directed.

S&F in repair 2 lever brass lock, cupboard grade 1, 50mm size complete all as specified and directed.

S&F in repair 6 lever brass type Mortice lock vertical type size 100mm complete all as specified and directed.

S&F in repair Block boards 18 to 19 mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work (as in cup board) incl taking down old board complete all as specified and as directed.

M&L in repairs 0.9mm thick decorative laminate type-1 of surface finish colour and pattern as approved fixed with approved adhesive as per manufacturer's instruction complete all as specified and directed.

M&L for small repairs of hinges of doors and windows, adjusting sliding door bolts, tower bolts, repair of handles, mortice locks etc and similar works complete all as specified and directed.

S&F in repair RCPC (Reinforced Cement Polymer Concrete) grating slab of size 900 mm x 600 mm x 100 mm thick, of Capacity 3 MT fixed in proper position complete as directed by Engr-in -Charge.

S&F in repair RCPC (Reinforced Cement Polymer Concrete) grating slab of size 600 mm x 450 mm x 100 mm thick, of Capacity 3 MT fixed in proper position complete as directed by Engr-in -Charge.

Removing of RCPC drain cover, any size or thickness from existing position, keeping aside and re-laying in position after completion of drain work complete all as specified and directed.

Taking out of interlocking paver block, any shape or size and removing from site complete all as specified and directed.

Supply and laying machine pressed precast concrete interlocking paver block with grey cement and pigmnent of any shape and size as approved by GE conforming to IS 15658-2006 of 60 mm thickness, M-35 grade including taking out existing unserviceable paver blocks complete all as specified and directed. (NOTE: Sand for cushioning level will be measured and paid seperately)

M&L Sand filling under floors under paver block, thickness not exc 50 mm including consolidation complete all as specified and as directed

MS AP CONSTRUTION AND CO

MS HORIZEN

JOY-EN-JOY

BASU AND CO

PRABIR TRADERS

UNIVERSAL TRADING CENTRE