SPECIAL REPAIR OF SURVEYED OFF CONDEMNED

Almirah Large with shelves Steel Overall size shall be 2050mm long, 900mm wide and 400mm high. All Steel shall be MS Square pipe of 18 Gauge. The head board shall be 800mm high and Foot board shall be 500mm high. The frame of head board and foot board shall be of 38mmx38mm MS square pipe.18mmx18mm MS square pipe shall be provided in the inner of head board frame/foot board frame as shown in drg.18mm thick both side decorative prelaminated particle board of walnut shade with PVC edging shall be screwed to MS strip arc welded to 18mm thick rectangular pipe with standard workmanship both in head board/foot board..25mmx65mm rectangular CR pipe shall be used to make the long rails and short rails of bed hard and welding shall be done for fixing long rails to the legs irrespective of what is shown on drg.One stiffener of size 25mmx25mm shall be welded between the two legs of headboard over 150mm from the ground level. The top of bed hard shall be of 12mm thick BWR ply of approved make fixed over the four equidistant stiffener of size 25mmx25mm SQ MS pipe in line with bottom of 25x65mm long rail section. PVC shoes shall be provided to legs of bed.All metal or iron work shall be treated with synthetic enamel black after doing two coats of metal primer.Rest all as per drg.

Almirah Med with shelves Steel Overall size shall be 1270mm high 765mm wide and 440mm deep. The base shall be made of two numbers mild steel sheet channel base welded to bottom of almirah and shall be 100mm high. Mild steel sheet shall be 1mm thick for channel base. The base channel shall be welded at 50mm from each end of 765mm length and shall be up to full width of 440mm of almirah. Top side, back bottom and front of almirah shall be of 1mm thick mild steel sheet. Three shelves equally spaced making four compartments shall be provided and shall be of 1mm thick mild steel sheet.Front shutters shall have two leaves.All joints and welding fixing shall be done according standard workmanship. HANDLE A steel chromium plated handle 100mm long shall be provided to the shutter. LOCKING DEVICE The locking device shall be three way locking device and shall also be provided with decorative key plate .Make of Lock Harrison or Godrej. FINISH All steel surfaces exposed to view when placed in position shall be painted with two coats of silver hammer paint over a coat of primer with spray machine after preparation of surfaces. A mark of MES shall also be provided on left top corner of front shutter of visible colour as directed by Engr In Charge. Rest all as per drgs.

Bed Hard 6 feet x 3 feet with ply top Overall size shall be 2050mm long 900mm wide and 400mm high. All Steel shall be MS Square pipe of 18 Gauge. The head board shall be 800mm high and Foot board shall be 500mm high. The frame of head board and foot board shall be of 38mmx38mm MS square pipe.18mmx18mm MS square pipe shall be provided in the inner of head board frame or foot board frame as shown in drg.18mm thick both side decorative prelaminated particle board of walnut shade with PVC edging shall be screwed to MS strip arc welded to 18mm thick rectangular pipe with standard workmanship both in head board or foot board. 25mmx65mm rectangular CR pipe shall be used to make the long rails and short rails of bed hard and welding shall be done for fixing long rails to the legs irrespective of what is shown on drg.One stiffener of size 25mmx25mm shall be welded between the two legs of headboard over 150mm from the ground level. The top of bed hard shall be of 12mm thick BWR ply of approved make fixed over the four equidistant stiffener of size 25mmx25mm SQ MS pipe in line with bottom of 25x65mm long rail section. PVC shoes shall be provided to legs of bed.All metal or iron work shall be treated with synthetic enamel black after doing two coats of metal primer.Rest all as per drg.

Book case steel large DIMENSION Over all size shall be of 840 mm long, 310 mm wide and 1675 mm high . DESCRIPTION All sheet shall be mild steel sheet 1 mm thick, back, sides, bottom, top and shelves.The book case shall be provided with four compartments of equal size. The shutters of each compartment shall open towards top and slide into the depth of the book case.Transparent glass 4mm thick shall be provided to front shutters. Two steel handles of 100 mm long shall be provided to each shutter of the compartment. The locking device shall be provided to each compartment with duplicate key and each shutter shall be provided with decorative key plate . FINISH All steel surfaces internally and externally shall be painted with two coats of silver hammer paint over a coat of primer with spray machine after preparation of surfaces. A mark of MES shall also be provided on top shutter of visible colour as directed by Engr-in -Charge.

Book shelf open large All as shown on drawing. Overall size shall be 915mm long 305mm wide and 1905 mm high sides and back shall be covered with 1 mm thick mild steel sheet. Slotted angle 25mm x 25mm x 3mm shall be provided at front and back as shown on drawing. 3mm thick corners of 75mm x 75mm shall be fixed at front and back to the top and bottom of shelves. seven sheves including top and bottom shall provided equall to make six compartments. all steel and iron surfaces shall be painted with two coats of enamel aint over a coat of primer after preparation of steel surfaces as directed by Engr in charge. welding shall be done as per the trade practice and as directed by the Engineer in charge.

Charpoy IP with hard top Overall size shall be 1980mm long, 900mm wide and 440mm high. Two long rails and two short rails shall be of 25mmx65mmx16 gauge MS rectangular pipe .The legs shall be of size 32mmx32mmx16 gauge welded to long and short rails as shown on drg.Two stiffeners of size 25mmx25mmx16 gauge shall be provided in equidistant between two opposite long rails. Six number cleat of size 25mmx60mmx6mm shall be welded with frame to support ply. Two stiffeners joining legs of size 25mmx25mmx16 gauge shall be provided at 150mm from ground level .12mm thick commercial plywood shall be provided for top as shown on drg with proper nut and bolt .one nut and bolt shall also be provided at centre of each stiffeners for fixing the plywood irrespective of what is shown on drg..PVC hard rubber shoes shall be fixed at bottom of each leg. All steel surfaces shall be painted with synthetic enamel black in color before applying a coat of primer. Rest all as per drg

Chair CB without Arms Steel Overall size shall be 535mm wide 560mm deep and 900mm high. Seat shall be 455mm high from floor. Conduit pipe used for frame shall be 20mm dia steel tubing having wall thickness 1.6mm Welding of frame where required shall be as directed by GE or BSO and in running welding grinded to give smooth surface.The seat and back frame of the chair shall be made up of quality sheesham wood in natural polish with polythene cane in godrej pattern confirming to IS 5378 94 Type I of durable qualty .The wooden seat frame shall be further supported by steel strips measuring 19mm x 3mm at the front and the rear and each strip shall be welded to ERW frame. Cane shall be 2mm wide and 0.4mm thick Gola type weighing not less than 6 gms 10 RM. Bottom of legs shall have hard rubber shoes. The seat and back shall be fixed by providing suitable nut bolts and washer. Painting shall be done with spray machine after preparation of wooden surfaces. All iron surfaces exposed to direct view Shall be painted with two coats of enamel grey paint over a coat of primer after preparation of steel surfaces

Chair Computer The Base pedestal assembly of chair computer shall be of dia 700mm and 1060mm high .The pedestal assembly shall be provided with injection molded in black 30% glass filled nylon. A 10.5mm dia forged bright Zinc plated MS Castor Pin is of press fitted into each prong for holding the castors. The seat and back of the chair computer shall be made of 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping allround.The back rest shall be adjustable and consist of drop lift mechanism and shall be adjusted in the insert .It shall be scratch and weather resistant. Rest all as per drg.and as per sample approved by BSO or GE

Chair Dinning Chair Dining with Seat cushioned shall be made to the shape size and design as shown on drg as specified in particular specification and shall be manufactured in accordance with relevant IS. All wood work shall be of kiln seasoned and chemically pressure treated Ist class hard wood Teakwood. Seat shall be 75mm thick of polyurethane foam density of 32 KgCu.m covered with fabric of acrylic or polyester or polypropylene and upholstered with good quality leatherised of make Sleep well Kurl on Coir foam as approved by GE. Plywood for seat shall be 12mm thick melamine faced prelaminated particle board bonded with phenol formaldehyde as per IS 3087 1985 exterior grade BWR type and shall be ISI marking on the edges. Exposed edges of board shall be covered with 4mm thick teak wood edging and shall be fixed as specified and directed. Toes Nylon buffers shall be of best quality as approved by GE and shall be provided under each leg and fixed with 25mm long steel screws of suitable size. Finishes All wooden surfaces exposed to view except under sides of frame and bottom of legs shall be French polished. All other items or fittings shall be as shown on drawing and provided as per relevant IS and trade engineering norms or pattern.

Chair Writing The frame of the chair shall be of MS tubular frame powder coated ,cantilever type of size 25mmx10mm in section. Back form shall be designed with contoured lumber support for extra comfort.120mm thick hot pressed plywood upholstered with superior quality fabric and moulded polyurethane foam with PVC lipping alround shall be provided at seat and back.PU arms shall be of superior quality and reinforced with MS insert.It shall be scratch and wheather resistant..Steel portion of chair shall be painted with two coats of synthetic enamel paint of black colour over a coat of primer.Rest all specifications are as per drg and directed by Engr-In-Charge