Supply and Installation of furniture in Non-BSL area of Wet Labs L-1 and L-3 at NCDC, 22, Sham Nath Marg, Delhi - 110054

NBCC (INDIA) LTD

(A Govt. of India Enterprises)

OFFICE OF THE SBG (DOP)

PROJECT: UPGARADATION OF NCDC

WORK: Supply and Installation of furniture in Non-BSL area of Wet Labs L-1 & L-3 at NCDC, 22,

Sham Nath Marg, Delhi - 110054

SUMMARY OF COST

TENDER AMOUNT (Rs.)

DSR NON-DSR/ MR TOTAL AMOUNT (Rs.)

(Inclusive of GST/ Taxes, Cess etc.)

Digitally signed by MAHABIR

Furniture Estimate for Wet Lab-1, NCDC , New Delhi

Providing in place of main table with overall size of table 2100 x 2250 x 750mm. The main table shall be 2100 x 1050 x 750mm. The side unit shall be 1200 x 500 x 750mm.

The table is made of 25 mm thick MDF – one side pre- laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap

within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-

14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with

0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-

12823:1990, edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade

confirming to IS- 12823:1990, edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board confirming to IS-

1 Main table 14587:1998 with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Each 1 1 1 1 1 5 99,850.00 4,99,250.00

Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock

for security. This must be greenguard certified.

Providing and placing High Back Chairs, The cushioned seat is made of Injetion moulded Plastic outer & inner. Plastic inner is upholstered with pure leather and moulded High

resilliance (HR) polyurathene foam of density 45±2 kg/mcube, and hardness load 16±2 kgf as per IS:7888 for 25% compression. Seat size should be:- 47.6cm (W) X 49.2cm

(D). The cushioned back is made of PU foam with insitu moulded MS E.R.W. Round tube of size 1.9±0.03cm X 0.16 ±0.0128cm. It is upholstered with pure leather. Back Size

shall be:- 47.5cm (W) X 77cm (D). The armrest top is moulded from poyurathene (PU) upholstered in pure leather and mounted on to a drop lift adjustable type tubular

armrest support made of 3.81± 0.03cm X 0.2±0.01cm thick M.S.E.R.W. tube having chrome plated finish. The armrest height adjustable upto 6.5 ± 0.5cm in 5 steps. The

adjustable tilting mechanism is designed with the following features:- 360 Degree revolving type, front pivot for tilt with feet resting on ground and continuos lumbure

support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back

tilting ratio of 1:2, The mechanism housind is made up of HPDC aluminium black powder coated. Seat depth mechanism is integrated in seat through a sliding mechanism.

Back frame is connected to the up/dn mechanism housed in plastic T spine. it can be adjusted in the range of 7.42 ± 0.5cm for the comfortable back support to suit individual

2 HOD Room Main Chair need. The pneumatic height adjustment stroke of 10.0 ± 0.3cm. The pedestal is high pressure Die- Cast polished aluminium and fitted with 5nos. twin wheel castors. The Each 1 1 1 1 1 5 34,950.00 1,74,750.00

pedestal is 65.0±0.5cm. 5 Nos. twin wheel castors are injection moulded in plastic having 6.0±0.1cm. wheel diameter and assembled to pedestal. the work shall be carried out

as per the instructions and guidance recieved from engineer incharge. This must be Bifma and Greenguard certified.

Providing and Placing in position Visitors. The cushioned seats shall be made of injection moulded plastic outer and inner. Plastic inner shall be upholstered with pure leather

and moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x

3 Visitor Chair 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with Each 3 3 3 3 3 15 12,950.00 1,94,250.00

pure leather. Back size shall be 47.5 cm W x 77 cm D. The tubular frame shall be cantilever type and made of Ø2.54±0.03 cm x 0.2±0.016 cm thick SS 202 tube. The back shall

be connected to the frame through chrome plated high pressure die cast connector piece.

Providing and Placing in place of 3 seater sofa. The overall dimensions shall be 2110 x 935 x 890mm. Understructure is made up of combination of plywood & pinewood

members. Plywood is 12±1mm thk. [moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 22x64mm, 34x64mm & 16x35mm without having

major knots & defects on the surface. Zigzag spring of dia. 3.8mm is mounted on the seat structure using plastic spring mounting clip for support & additional cushioning

purpose. Non woven fabric is stapled on the seat structure frame above the spring asly. to avoid direct contact between the metal springs and the seat foam. Powder coated

MS support pipe is fitted with the wooden seat frame to give additional strength to the structure. Seat is made of PU foam with density 28 kg/m3 with a top layer of supersoft

PU foam with density 32kg/m3. Recron sheet of 200GSM is wrapped & glued above this seat top foam. Seat front bottom is glued with the PU foam with density 28 kg/m3. :

Seat upholstery is made in polyester fabric, having pockets to insert the seat foam. The fabric has a special coating which gives it a leather like feel. Plastic legs with the

M8 stud are fitted at the bottom surface of both the armrests and on front of the seat.

Supplying and placing Centre Table. It shall be of Dimensions 1100mm x 600mm x 460mm with 10 mm tampered glass top. It shall also have 8mm thick tampered bottom

5 Center Table glass for storage option. It shall have Chrome plated understructure. It must have Passed 48 hours salt spray test. athe Glass is attached to the understructure via UV disc. It Each 8 8 8 8 8 40 19,500.00 7,80,000.00

Load bearing capacity shall be 30Kg UDL.

Supplying and placing in position Conference table of the following specifications. 6 Seater Boat Convex size shall be 2100 Width mm x 1200 Depth mm x 750 Height mm .

Top shall be 32 mm thick base material shall be 18 plus 12 mm MDF board . Post - laminated work - surface with 0.6 mm laminate on top and bottom surface plus 2 mm

thick PVC edge banding shall be on straight top side edge and especially designed chamfered T - beading fixed at bottom side edge for sleek look . The veil and cross member

shall be 18 mm thick base material shall be 16 mm plain particle board post laminated with 0.6 mm top laminate on either side plus 2 mm thick and 0.8 mm thick PVC edge

banding . The legs shall be made from 1.6 mm matt silver anodized aluminium extrusion .Legs assembeled together with a plastic glide holder at bottom and 5 mm thick MS

powder coated sheet at top . Also there shall be accessflap and switch mounting tray made from matt anodized aluminium extrusion .

Digitally signed by MAHABIR

The seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade UV Resistance. The Powder coated (DFT50+ microns) weled tubular

frame is made from 2.22 + 0.03 cm x 0.16+/- 0.0128cm and 3.5+/- 0.03 cmx1.5+/-0.03 cm x 0.16 +/- 0.0128 cm M.S.E.R.W tube.The powder coated weled beam M.S. Structure is made from

5.08+/-0.03cm x0.16x +/- 0.0128 cm.The Shoes are made of high impact strenght polypropylene polymer compond with indoor grad UV Resistance and pressed fitted with tubularfram. The

Armrest made of high impact strenght polypropylenne polymer compound with indoor grad UV resistance and assembly over the tubular frame. The "L" Shape Desket is made of 1.8+/- 0.05cm

thk . pre - laminated Perticleboard with 0.2+/- 0.05 cm thk injection polypropylene polymer all around Front & Back ( outher Dimension - 31.5+/-(W)x 47.0+/- 0.1 cm (D)) An Upholstry cover be

retro fitted on seat and back . the seat cover is made fromhigh abrasion resistance with fabric with foam laminated and 2.5cm PU Foam insert. the back cover is made from HIgh Abrasion

Resistance fabric with foam lamination and 0.1 cm PU foam .

SIZE : (W)57.5cm*(D)67.8cm*(H)84.5cm*(seat H) 45.0 cm

Seat Size 52.5cm(W)*53.2 cm(D)

Back Size 51.6 cm(W)*40.5 cm (H)

Providingin place of main table with overall size of table 1800 x 2100 x 750mm. The main worktop shall be 1800 x 900 x 750mm and Side unit shall be 1200 x 500 x 750mm.

The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap

within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-

14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with

0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-

12823:1990, edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade

confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board confirming to IS-

14587:1998 with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides.

Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

This must be greenguard certified.

Providingin place of main table with overall size of table 1500 x 750 x 750mm. The main worktop shall be 1650 x 750 x 750mm and Side unit shall be 900 x 500 x 750mm.

The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap

within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-

14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with

0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-

12823:1990, edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade

confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board confirming to IS-

14587:1998 with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides.

Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

This must be UL greenguard certified.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity

yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression.

The armrest has an up=Down adjustment of 8.5 ± 0.5cm which is provided in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is

made up of plastic injection moulded nylon with textured top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point

control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad

with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the

pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions recieved from

Engineer Incharge. This shall come along a headrest from same family. It shall be SCS IAQ certified for Indoor Air Quality.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity

yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression.

The armrest has an up=Down adjustment of 8.5 ± 0.5cm which is provided in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is

made up of plastic injection moulded nylon with textured top. It shall have Front pivot synchro mechanism with following features. 360 degree revolving type, Single point

control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad

with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted through two projecting knobs provided on the rear side of the

pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions recieved from

Engineer Incharge. It shall be SCS IAQ certified for Indoor Air Quality.

Body panels are made of 18 mm thick ISI marked Commercial plywood (Moisture Resistant grade plywood) faced with 1.0 mm thick laminate on both sides, All

the exposed edges are edge banded with 2 mm thick PVC edge banding. Openable Doors/Sliding Doors shall be made of 18 mm thick ISI marked Commercial

plywood (Moisture Resistant grade plywood) faced with 1.0 mm thick laminate on both sides all the exposed edges are edge banded with 2 mm thick PVC edge

Side panel are made of 18 mm thick ISI marked Commercial plywood (Moisture Resistant grade plywood) faced with 1.0 mm thick laminate on both sides, all

12 Storages the exposed edges are edge banded with 2 mm thick PVC edge banding, 5 nos. Drawer/shelf components shall be made of 25mm thick ISI marked Commercial Each 0 -

plywood (Moisture Resistant grade plywood) faced with 1.0 mm thick laminate on both sides. All the exposed edges are edge banded with 2 mm thick PVC

edge banding. Body back and drawer bottom are made of mm 18 thick ISI marked Commercial plywood (Moisture Resistant grade plywood) faced with 1.0

mm thick laminate on both sides. Hardware: The high-quality hardware like Roller slides, SS Hinges, Mini fix, SS Handles, 3-way locks, wooden dowels, screw,

shall be used of Hettich, EBCO make or equivalent or as approved by engineer in charge/employer. Commercial plywood and Laminate Make: Century/Action

Tesa/Green Ply or equivalent/or as approved by engineer in-charge/employer), Wooden Wardrobe as approved by engineer in-charge/employer.

Digitally signed by MAHABIR

Providing and placing of Steel Almirah overall size: 916mm(W)x486mm(D)x1980mm(H) with welded construction. Almirah shall be made of CRCA ‘D’ grade high yield

strength, CRCA sheets conforming to grade as per CRI of IS 513 (part-1):2016, It should have 4 Nos. shelves with thickness of 0.6 mm, Back thickness of 1.0 mm, Door

thickness of 0.6 mm (high yield strength) and stiffener shall be provided in door up to full height, Width of stiffener: 115 mm, Stiffener sheet thickness: 0.8 mm and all other

components shall have thickness of 0.6 mm. The Steel Almirah should have a Mazak handle and Three-way locking mechanism with Shooting Bolts. It should have a height

wise adjustable shelf mounting which shall have a Uniformly distributed load (UDL) for shelves: 80 Kg. Almirah also have a M10 Screw type Leveller with Hex plastic base,

Number of hinges (for each door): 03 Nos. Hinges sheet thickness: 2 mm,Pedestal height (± 5 mm): 125 mm, The finishing shall include Epoxy powder coated with thickness of

50 microns (+/- 10%).Powder coating: Conforming to IS: 13871. . The product should be complete and as per sample approved & as per direction of Engineer-in-

charge/employer.

Supply Installation of linier workstation size 1200mmWX600mmDx1200-1250mmH Providing and placing of modular partitions system coated aluminum trims and

supported on Legs for better air circulation and helps in keeping floor clean. Panels Construction - Each panel consists of Vertical extrusions 2Nos and Horizontal extrusions

made of 1.2mm thick aluminum with duly powder coated at every division of tile/block. Each panel have Bottom frame fabricated for 52.4mm panel comprises of L-channels

made of 2mm thick CRCA steel (IS: 513), formed plates of 3mm thick HR steel (IS: 2062) & ERW steel tube of size 35x15x1.6mm thick in oval cross section (IS: 7138) welded

together. The complete bottom frame shall be powder coated with an average of 50-60 microns thickness of epoxy powder coating. The Bottom Frame is bolted with the

Upright verticals. Each Panel is provided with 2 Nos Legs of height 120mm are fixed at the bottom frame of the panel. Legs are fabricated by CO2 welded MS Tube of section

38mm x 25mm (IS: 7138 ERW Tube, 38mm x 25mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5mm HR) over which an M8 Leveller is fitted which

allows for adjustment of the height by 50mm. It will be coated with 45-50micron thickness of epoxy powder coating. Each Panel consists of 2Nos Intermediate blocks. In a

52.4mm Thick panel intermediate block shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm decorative laminate on both sides.

Particle board framing shall be used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks will be

located in the middle bands of the panels made out of a composite construction of MDF and paper honeycomb. Each Panel consist of TOP TILES/SPLIT TILES. These tiles shall

be slide in to the panels from top before fixing the top horizontal. These tiles shall be supported from top & bottom side with clips made from PP co polymer fitted in

horizontal extrusion. In case of split tiles it shall be offered in Fabric magnetic tiles, Whiteboard tiles. Each Panel consists a BOTTOM TILE. These bottom tiles shall be press

fitted on to the assembly frame of the panel with the help of snap on clips made of nylon-66 and support clips made from Polypropylene(PP). All partitions and side panels

have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring.

Tile Finishes :

a FABRIC MAGNETIC TILES: Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with

• FABRIC TACK TILES: Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with Polyurethane foam in the tile for tackability. The

fabric shall be upholstered with adhesives.

• WHITE BOARD TILES : White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.8 mm thick white glossy high pressure

laminate on outer side & 0.8 mm backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging. Aluminium Trims : The top trims

and end trims for 52.4 mm shall be made from aluminum extrusion. All kinds of extrusions for 52.4mm shall have average wall thickness of 1.2 mm & having finish of powder

coating. Top trim in 52.4mm thick panel shall be press fitted on the horizontal extrusion, it shall be slide fitted with the help of top trim connector made from PP copolymer

End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513.Wire Management - Wires

shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Wires runs through

the system from Bottom tile and extended to the top at various locations by the help of 2 nos. vertical Cable Ducts in each panels.

Cable duct shall be made from 0.8 mm thick M.S. CRCA Grade D as per IS: 513 - 1994. It is constructed with two parts, one is body & another is cover. It holds the cables &

gives aesthetic appearance by covering all cables entry, which are moving upward to the panels. Size of Cable duct is 107mm W X 154 mm H X 21 mm D. Legs - System shall

also have 120 mm high powder coated welded metal legs to give the system an elevated look. Single side legs are fabricated by CO2 welded MS Tube of section 38 mm x 25

mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35mm x 22mm x 5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted.

End/Intermediate separator : partitions of 22.8mm thick including powder coated aluminum trims and supported on Legs for better air circulation and helps in keeping floor

clean. The 22.8 mm panels are only to be used as Separator/End panels to provide additional privacy. These panels have various finishes and no cable management ability.

Panel Construction : The 22.8mm End/Separator panels shall be made of horizontal and vertical uprights. These uprights and horizontals shall be made of aluminum extrusion

having material AL96063-T6 & have average wall thickness of 1.2mm & powder coated with epoxy-polyester powder. The Blocks for the End/Separator panels shall be of

16mm to 18mm thickness in the selected finish. The top most block in the panel shall be the top block of the panel. It shall be available in fabric, laminate, whiteboard, fabric

metal, tackable and clear glass finishes. The 2Nos blocks in the intermediate bands shall be available in fabric or laminate finish and the lowermost block in the panel shall be

the bottom block which shall be in fabric, metal or laminate finish. Tiles : Tile Finishes in End/Separator Partitions to be provided as per the site and layout approval. Finishes

Computer Facility Workstations in these panels shall be

1200 x 600 • LAMINATE FINISH BLOCKS:

Laminate finish blocks shall be made from 18mm thick particle board, cladded with 1mm thick laminate of approved shade.

• FABRIC FINISH BLOCKS:

These shall be made from 18mm thick Pre-Laminated Particle Board upholstered with 1mm thick approved shade of fabric using adhesives.

• WHITEBOARD BLOCKS:

These shall be made of 16mm thick particle board laminated with 0.8mm thick white glossy high pressure laminate on both sides and having all its edges with minimum 0.6

mm thick PVC edging.

• GLASS BLOCKS:

These shall be made of 4mm thick toughened plain glass having diamond polish edge finish.

• FABRIC TACKABLE BLOCKS:

These shall be made from 18mm thick Pre-Laminated Board battens which hold 3mm MDF in between. 6mm thick Polyurethane foam shall be pasted on 3mm thick MDF and

this assembly shall be upholstered with approved shade of fabric on both sides using adhesive.

• METAL FINISH BLOCKS:

Metal finish blocks shall be made from two components of 0.8mm thick M.S. CRCA Grade D as per IS: 513 powder coated with epoxy polyester finish. Aluminum Trims : The

top trims and end trims for 22.8mm partition shall be made from aluminum extrusion having material AL96063-T6. Top trim in 22.8mm thick panel shall be slide fitted with

the help of top trim connector made from PP copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from

2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick panel shall slide with the help of end trim connector made from nylon-66.Workstation Worktop as

per the approved shape and site requirement made out of 25mm thick pre laminated particle board. All the open edges of work surface shall be provided with machine

pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of

wires. These cut outs shall be provided with ABS covers. Work surfaces are fitted to the panels by work surface brackets. Brackets are made of 2.0mm thick CRCA grade D

steel as per IS : 513-19. Brackets are slide in between end trim and vertical extrusions. computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA

steel as per IS : 513I made of 0.9mm thick powder coated with sliding channels and other fixtures/fittings. It should also have a sliding system for accomodating mouse. CPU

Trolley of Size - 345mm(W) x 226(D) x 180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-

lockable twin wheel castors are injection moulded in Black Nylon. Mobile Pedestal having 3 Drawers Unit having flat metal front and top with Central locking. The Drawer

Unit consists of 2Box and 1File Drawers. The Overall size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit : Welded

Assembled of 0.8 thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, 1.2mm thick CRCA Top Stiffener & Bottom stiffener.

Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in

shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism. Top Panel : 0.8mm thick Metal Straight Edge Top.

Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50

microns (+/-10). Work station as approved by engineer in-charge/employer

Digitally signed by MAHABIR

These shall be made from 18mm thick Pre-Laminated Board battens which hold 3mm MDF in between. 6mm thick Polyurethane foam shall be pasted on 3mm thick MDF and

this assembly shall be upholstered with approved shade of fabric on both sides using adhesive.

• METAL FINISH BLOCKS:

Sr. No. Name of Items Metal finish blocks shall be made from two components of 0.8mm thick M.S. CRCA Item Grade D as per IS: 513 powder coated with epoxy polyester finish. Aluminum Trims : The

Description Unit GF 1st 2nd 3rd 4th Total Qty Rate (Rs.) Amount (Rs. ) Reference Image

top trims and end trims for 22.8mm partition shall be made from aluminum extrusion having material AL96063-T6. Top trim in 22.8mm thick panel shall be slide fitted with

the help of top trim connector made from PP copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from

2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick panel shall slide with the help of end trim connector made from nylon-66.Workstation Worktop as

per the approved shape and site requirement made out of 25mm thick pre laminated particle board. All the open edges of work surface shall be provided with machine

pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of

wires. These cut outs shall be provided with ABS covers. Work surfaces are fitted to the panels by work surface brackets. Brackets are made of 2.0mm thick CRCA grade D

steel as per IS : 513-19. Brackets are slide in between end trim and vertical extrusions. computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA

steel as per IS : 513I made of 0.9mm thick powder coated with sliding channels and other fixtures/fittings. It should also have a sliding system for accomodating mouse. CPU

Trolley of Size - 345mm(W) x 226(D) x 180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-

lockable twin wheel castors are injection moulded in Black Nylon. Mobile Pedestal having 3 Drawers Unit having flat metal front and top with Central locking. The Drawer

Unit consists of 2Box and 1File Drawers. The Overall size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit : Welded

Assembled of 0.8 thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, 1.2mm thick CRCA Top Stiffener & Bottom stiffener.

Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in

shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism. Top Panel : 0.8mm thick Metal Straight Edge Top.

Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50

microns (+/-10). Work station as approved by engineer in-charge/employer

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch knitted

polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back

are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back,

without need for complex manual adjusments. The cantilevered seat offers impact cushioning while seating and synchronises with the back movement during posture

changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the back spine structure

involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt limiter feature which is inbuilt in saet base and the

tension is user weight dependent. The adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide.

The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors. The

pedestal is 66cm pitch centre diameter and 76cm with castors. The overall dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-

53.8cm). This must be UL Greenguard certified and AIOTA certified for ergonomic health.

Providing and Placng in place of canteen table. Th overall dimensions of the tbale shall be 1350 x 600 x 750mm. Tablr top shall be made from 25mm thick MDF OSR board

with PU coating on top side. Legs are made by welding the combination of MS ERW round tube of dimater 63.5mm x 2mm thick. Flamges of 1.6mm thick CRCA and 1.2mm

thick. Insde platew are made from HR 5mm thick sheet. Assembly is epoxy polyester powder coated. Table top folds upside at offset center pivot provided on support bracket

which is Aluminium alloy pressure die cast part coated with epoxy olyester powder caoted min. 40 microns. Table top connected with spring loaded mechanism with pull

handle made of snadwich tubes of MS ERW 1.2mm thick and 1.6mm thick tubes. Coated with epoxy polyester powder coated min. 40 microns. Legs are provided with casters

of 65mm diameter loackable type for ease of movement and can be locked when required at any position. This must be greenguard certified.

The seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade UV Resistance. The Powder coated (DFT50+

microns) weled tubular frame is made from 2.22 + 0.03 cm x 0.16+/- 0.0128cm and 3.5+/- 0.03 cmx1.5+/-0.03 cm x 0.16 +/- 0.0128 cm M.S.E.R.W tube.The powder coated

weled beam M.S. Structure is made from 5.08+/-0.03cm x0.16x +/- 0.0128 cm.The Shoes are made of high impact strenght polypropylene polymer compond with indoor

grad UV Resistance and pressed fitted with tubularfram. The Armrest made of high impact strenght polypropylenne polymer compound with indoor grad UV resistance and

assembly over the tubular frame. The "L" Shape Desket is made of 1.8+/- 0.05cm thk . pre - laminated Perticleboard with 0.2+/- 0.05 cm thk injection polypropylene polymer

all around Front & Back ( outher Dimension - 31.5+/-(W)x 47.0+/- 0.1 cm (D)) An Upholstry cover be retro fitted on seat and back . the seat cover is made fromhigh abrasion

resistance with fabric with foam laminated and 2.5cm PU Foam insert. the back cover is made from HIgh Abrasion Resistance fabric with foam lamination and 0.1 cm PU

Seat Size 52.5cm(W)*53.2 cm(D)

Back Size 51.6 cm(W)*40.5 cm (H) The product must be UL greenguard gold certified.

Supply and installation of stool as per technical specification. STOOL: Overall Sizes Diagonal Leg Diameter 538 mm, minimum height 470mm - maximum height :655mm ±2%

tolerance, Top base shall be made of Stainless steel 304grade sheet with spin section of thickness 1.2 mm & should be non-corrosive. It should have a diameter of 305mm,

seat base is made of MS ring and rectangular tube. EN8 Screw having diameter of 22mm should be used for height adjustment of the seat base. The hub should be made of

MS ERW tube having diameter of 38mm and thickness 2.0mm. The Hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.

The under structure should consist of 4 legs made up of MS ERW tube of diameter 25.4 mm and 1.6mm thick. The press formed pipe leg should give a round & clean look. All

the legs should be provided with 4 nos. of Nylon-6 bush. All metal components should be pre-treated with zinc phosphating in 9 tank process and then powder coated with

anti-microbial epoxy polyester powder coating to fulfil the requirements for bacterial protection against at least 2 commonly found bacteria in Hospital environment [Gram

positive and Gram Negative]. Safe working load must be 135 kg or above. Stools approved by engineer in-charge/employer.

Digitally signed by MAHABIR

Supply and installation of stool as per technical specification. The seat shall be made up of 1.2±0.1cm thick flat plywood measured as per QA method described

in OCP-QLTA-P14-18 and with moulded Polyurethane foam and are upholstered with replaceable synthetic leather covers. The dimensions of Seat shall be

Diameter 40.0 cm

and Adjustments are 360° Revolving type. The back foam shall be designed with contoured Lumbar support for extra comfort. The upholstery shall be available

in synthetic leather. The dimensions of Back shall be 45.0 cm (W) covered with polyurethane foam. The HR polyurethane Foam shall be moulded with density =

45 +/-2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The manual height adjustment shall be very easy to operate with a help of a

knob. It should be easily locked at the most comfortable position. The five-prong pedestal shall be fabricated from 0.2 ± 0.02 cm thick HR sheet (IS : DD 1079/ Each 40 40 40 40 40 200 6,950.00 13,90,000.00

HR ), Powder coated ( DFT 40-60 microns ) and shall be fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The

pedestal shall be 55.0±0.5cm pitch-circle diameter (65.0±1.0cm with castors). Circular-foot-ring ofDia 52.0±0.2cm shall be made up of 01.9±0.2 x

0.12±0.0096cm thk MS ERW Tube for foot support in High-base stool. The twin wheel castors shall be injection moulded in Black Nylon. Overall dimensions shall

be Width- 65.0cm, Depth- 65.0 cm, Seat Height- 45.0 to 56.5cm. Stool as approved by engineer in-charge/employer.

Supplying and placing in position Office table of the following specifications. Table size shall be 1200 Width mm x 600 Depth mm x 750 Height mm . Table top shall be 25

PA Cabin/Security Staff table 1200 mm thick Prelamnated MDF Board with 2 mm thick PVC edge with 35 KGS , shelf shall be 12.5 KGS drawer shall be 506 KGS. The table top shall be 18 mm prelam particle

x 600 board , 3 mm prelam MDF board. Metal parts shall be BM Slide For Keyboard plus castor mounting table plus locking bracket plus angle clit . Hardware shall be Screw , KD

fitting , Wooden Dowel , PVC ibserts. Construction shall be KD fitting , Wooden dowel & Angle Clit.

Supplying and placing in position Main desk of the following specifications. Main Desk size shall be 1350 Width x 750 Depth x 750 Height.The Top shall be in white cedar and

26 Seminar Table black and shall be 25 mm Prelamnated MDF Board with 2 mm thick PVC lipping.The side panels shall be 18 mm thick Prelaminated MDF Board with 2mm thick PVC. The Each 3 3 3 3 3 15 22,950.00 3,44,250.00

Modesty panel shall be 18 mm thick prelaminated MDF Board. The Modesty panel shall be in a combination of black & white cedar.

The seat and back to be made up of high-density self-skin 25-30mm thick PU Foam reinforced with 1.2 mm thick MSperforatedsheetinsert.ThePUFoamhavingdensityof680+/-

10Kg/m3with hardness of 55 +/-5. Seat Size :52.0 cm (W) X 46.5 cm (D). Back Size: 52.0 cm (W) X 51.5 cm (H). Floor to seat height (front) minimum: 410mm, Overall length

(minimum): 1680mm, Cross Beam made up of black powder coated MS ERW square tube of size 6.0+/- 0.05cm X 6.0+/- 0.05cm X0.4+/-0.016 cm thick fitted with

polypropylene end caps. Thickness of the seat support and lumber support (minimum): 23mm, Legs & Armrest made up of powder coated High pressure Aluminium Die cast

Powder coated with minimum 70 microns. Number of armrests: 04 Nos. Thickness of material of Arms 1.8 mm, Thickness of material of Legs 2.0 mm, Legs are fitted with

soft grip PVC level adjusting shoes. Main frame finish with Powder coated of minimum 50-70microns, 3-seaterwaitingchairasapprovedbyengineerin-charge/employer.

C-FRAME ASSEMBLY:- All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard

Specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994.

The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops

Its superior strength combined with aesthetically appealing end caps should give maximum flexibility and modularity while making a layout.

C-frame should be constructed from a rectangular pipe with a cross section of 60 mm x 30 mm and should be 2 mm thick and should be without a vertical front leg to give a

clean look. This should provide more knee space or leg space and should facilitate uninterrupted lateral movement of the under-bench units within the bench run.

The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring

The tubular enclosed type construction should discourage dust accumulation and unwanted development of bacteria & fungus

Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems.

The structure should heave a removable back panel to provide access for maintenance throughout the length of table

The C-frame should also have skirting at back bottom side. The C-frame should be suitable for sitting and standing nominal heights of 750mm & 900 mm respectively.

The nominal table depths should be 770 mm and 920 mm for wall side and 1540 mm, 1840mm for Island tables.

The Corner Units should fit well with 770mm & 920 mm table depths. All frame-work is to be pre-treated with superior pure epoxy powder coated finish.

Under Bench Module for C-Frame

Completely made of 1.2 mm(+/-0.1mm) CRCA sheets. The shutter & drawer front should be of sandwich construction. Foam sheet filled in shutter gaps is not allowed. The

sound suppressor plastic bumpers to be used to minimize banging noise while closing the shutter. The entire module should be made up of GI panels and are bolted for high

corrosion resistance. Welding of modules is not acceptable. The shutters should be mounted to the modules by hinges which are openable to 95 degree & self- closing on

return. Lockable roller bearing must be used so that the drawer will not fall. The telescopic drawer slides which should be very sturdy & able to take load of 35(+/-5) kg. All

modules must have lock and dual key. The lock ring should be plastic.

Detailed specifications and thickness of CRCA sheet items in each module: - Cabinet end panels; min. 1.2 mm thick CRCA sheet - Cabinet rear panel and top panel; min. 1.2

mm thick GI sheet - Cabinet base skid; 1.0 mm thick CRCA sheet - Cabinet drawers; 1.2 mm thick CRCA sheet - Cabinet shutters & drawer front panels; double skin const, min

1.2 mm thick CRCA sheet - Cabinet main frame structure and drawer slide rails, 1.6 mm thick GI Sheet - Each cabinet shall have self-standing type base skid plinth in CRCA

ELECTRICAL Raceway.

Single Sided CRCA Electrical Raceway, Max L-2mtr , H-125mm x D-85 mm Top/ Wall Mounted with 3 Nos. 6 Module Cut-outs

Single sided Electrical Raceway is made up of 0.8mm thick CRCA MS Sheet

The complete CRCA material of cabinet should be pre-treated (degreased, Zinc phosphate) and epoxy powder coated for netter corrosion resistance.

The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours

LAB furniture Storage It should have high temperature withstanding capacity with excellent electrical insulation properties.

Understructure The rear portion of above accessories which is in contact with live metal should be made from thermos set material which will not melt on heating.

Switches & Sockets

Set of 5A - 1no. & 15A - 1no., Switches & Sockets with Face Plate (ANCHOR ROMS/

NORISYS) without wiring.

These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. They impart excellent electrical insulation properties i.e., do not melt on

heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures.

Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings

-Supply and Installation of Laboratory Workbenches, Regent shelf, Storage units, Sink Unit, Corner unit, including granite worktops and other supporting

structures/hardware’s based on the specified Make List. - Supply & Installation of all utility service outlets and accessory fittings, electrical receptacles, switch, socket, wire

electrical raceway etc. plumbing and electrical switches & fittings identified on drawings as mounted on the laboratory furniture or as per engineer in-charge/client direction.

-Supply & Installation of all laboratory sinks, bottle traps, drain troughs etc.

-Supply & Installation of service structures where specified and setting in place reagent

shelves of the type shown in the drawings.

-Removal of debris, dirt and rubbish accumulated as a result of installation/commissioning of the laboratory furniture and accessories and leaving the premises broom clean

List of approve makes: - Steel: TATA Steel, JINDAL Steel/Equivalent or better or As approved by engineer in-charge/employer.

Digitally signed by MAHABIR

Powder Coating Kansai Nerolac, Berger Paints, Asian Paints/ Equivalent or better or As approved by engineer in-charge/employer. SINGH

Water Faucets and Gas Valves: As approved by engineer in-charge/employer.

Switches and Sockets, Data and LAN points: As approved by engineer in-charge.

1.2 mm thick CRCA sheet - Cabinet main frame structure and drawer slide rails, 1.6 mm thick GI Sheet - Each cabinet shall have self-standing type base skid plinth in CRCA

ELECTRICAL Raceway.

Single Sided CRCA Electrical Raceway, Max L-2mtr , H-125mm x D-85 mm Top/ Wall Mounted with 3 Nos. 6 Module Cut-outs

Sr. No. Name of Items Single sided Electrical Raceway is made up of 0.8mm thick CRCA MS Sheet

Item Description Unit GF 1st 2nd 3rd 4th Total Qty Rate (Rs.) Amount (Rs. ) Reference Image

The complete CRCA material of cabinet should be pre-treated (degreased, Zinc phosphate) and epoxy powder coated for netter corrosion resistance.

The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours

LAB furniture Storage It should have high temperature withstanding capacity with excellent electrical insulation properties.

Understructure The rear portion of above accessories which is in contact with live metal should be made from thermos set material which will not melt on heating.

Switches & Sockets

Set of 5A - 1no. & 15A - 1no., Switches & Sockets with Face Plate (ANCHOR ROMS/

NORISYS) without wiring.

These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. They impart excellent electrical insulation properties i.e., do not melt on

heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures.

Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings

-Supply and Installation of Laboratory Workbenches, Regent shelf, Storage units, Sink Unit, Corner unit, including granite worktops and other supporting

structures/hardware’s based on the specified Make List. - Supply & Installation of all utility service outlets and accessory fittings, electrical receptacles, switch, socket, wire

electrical raceway etc. plumbing and electrical switches & fittings identified on drawings as mounted on the laboratory furniture or as per engineer in-charge/client direction.

-Supply & Installation of all laboratory sinks, bottle traps, drain troughs etc.

-Supply & Installation of service structures where specified and setting in place reagent

shelves of the type shown in the drawings.

-Removal of debris, dirt and rubbish accumulated as a result of installation/commissioning of the laboratory furniture and accessories and leaving the premises broom clean

List of approve makes: - Steel: TATA Steel, JINDAL Steel/Equivalent or better or As approved by engineer in-charge/employer.

Powder Coating Kansai Nerolac, Berger Paints, Asian Paints/ Equivalent or better or As approved by engineer in-charge/employer.

Water Faucets and Gas Valves: As approved by engineer in-charge/employer.

Switches and Sockets, Data and LAN points: As approved by engineer in-charge.

The floor mounted cabinet with sink cut out are made up of 1.2 mmm thick CRCA MS sheet. The complete MS material of cabinet is epoxy powder coated with thickness of

32 Sink Cabinet 50-60 microns. The shutters are powder coated. The shutters are fixed with auto closing doors hinges. The drawer trays are mounted on telescopic slides. Multipurpose locks Each 5 5 5 5 5 25 10,557.00 2,63,925.00

are used wherever required.

Providing and fixing leg space with a provision of Slim drawer of 150mm ht. drawer front is made up of 1.2 mm thick CRCA MS Sheet. The complete MS material of drawer s

epoxy powder coted with 50microns. The drawers trays are mounted on telescopic slides.

Reagent shelves with complete modularity design consists of horizontal 2 stage storage shelves. The end vertical support and horizontal shelves are made up of 0.8mm thick

34 Reagent Shelf CRCA MS sheet. The horizontal shelf have a provision for fixing the service panel to it. The service panels carry electrial switches and socket cutouts.The carcass is of 1.2mm Each 6 6 6 6 6 30 7,485.00 2,24,550.00

thick 30mm x 30mm heavy duty MS square tubes. The structure of the unit is epoxy powder coated with powder coating thickness of 50 microns.

It should be makeup of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. PP Bottle-traps should be offered with PP Sinks Standard

3-way Tap to be be provided with the Sink Unit, which should have 2 fixed Bib Cocks & One Swan Neck Swivel Cock made in Brass and heavy duty knobs. 360' Swing Goose

Neck Spout with Brass Head Work.

37 Granite Top GRANITE:- It should be 18 +/-1mm thick, jet black granite with edges having chamfer of 4 x 4 mm on top side. The overhang on the storage cabinet should be 25 mm at the Sqmt 45 45 45 45 45 225 8,450.00 19,01,250.00

front side and 30 mm at the sides.

1. Racks are required to store samples/kits in walk-in deep freezer (-20oC to -40oC) and walk-in refrigerator (+2oC to +8oC).

2. The racks should be easy to assemble, adjust or configure.

3. The individual racks should have wheels to facilitate easy mobility and lowest shelf should be approximately 6-8 inches above the ground.

4. There should be gap of approximately 1 – 3 feet between two shelves.

5. Topmost shelf should be at least 2 – 3 feet from the roof.

6. The racks should be made from lightweight, non-corrosive, rust proof and extremely durable metallic material (composite).

7. The racks should be easy to clean with routinely used cleaning solutions.

8. The racks should be resistant to scratching, peeling and corrosion.

9. The racks should withstand temperatures as cold as -35ºC and warm environments up to +50ºC.

10. The racks should have warranty for a period of five years.

Size specifications:

No. of shelves in each rack – 4 (Four) to 6 (Six)

No. of racks required – Approximately 6 (Six) (Exact number will be decided at the time of installation as per number of racks fitted to the room)

Length – Approximately 3 feet to 6 feet

Width – Approximately 2 feet

Height – Approximately 5 feet to 7 feet

Digitally signed by MAHABIR

4 shelf Shoe rack should made up of SS 304 ,Height of shoe rack: 1200 mm (±10 mm), Width of shoe rack: 950 mm (±10 mm), Depth of shoe rack: 380 mm (±10

mm), Frame sizes: 25 mm X 25 mm X 1.2 mm(thick), Distance between each shelves ±10 mm: 300 mm, Ground clearance: 100 mm (±10mm), Thickness of

Side/Back/Top sheet Covering material: 1.0 mm thick Stainless steel (SS-304 grade), Shelves thickness/size: 0.8 mm thick Stainless steel sheet of 304 grade,

Welding: Frame pipes and sheet work to be welded with MIG welding and buffed/grind neatly, Should have a dust tray to collect the dust , shoe rack to keep

24 pair of shoes (max 4 tier). Shoe Rack (24 Pairs) as approved by engineer in-charge/employer

Supply and Installation of 4 Door Personal Locker Unit (Base) with size of 450mm(W)x480mm(D)x1900mm(H) (± 5 % ) Stiffened pedestal height shall be 75 mm,

Number of compartments shall be 4. Stack ability shall have add - on units that can be stacked width wise to form bank of locker shaving common side panel.

Non-welded hinges with removable hinge pins should be provided. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement and

duplicate key should be provided. Material shall be CRCA Sheet. sheet thickness of body, back, shelves, pedestal and door must be 0.8mm thick. Construction

shall be Rigid Knockdown construction; the uniformly distributed load capacity of shelves shall be 40 Kg minimum. Finish shall be epoxy polyester powder

coated with 50-60microns thickness. Handle/Label holder shall be Electroplated Mild Steel handle/label. Ventilation shall be attractive punched pattern for

ventilation. Or As approved by engineering-charge/employer.

Digitally signed by MAHABIR

Furniture Estimate for Wet Lab-3, NCDC , New Delhi

Providing in place of main table with overall size of table 2100 x 2250 x 750mm. The main table shall be 2100 x 1050 x 750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm

thick MDF – one side pre- laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface

for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is

HOD CABIN, Main Table : 2100(W) made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin

X 900(D) X 750(H) board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2

1 Side Unit : 1200(W) X 500(D) X grade and approved shade confirming to IS- 12823:1990, edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board confirming to IS- Each 1 1 1 1 1 1 6 98,950.00 593700.00

750(H), Pedestal : 400(W) X 14587:1998 with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is

450(D) X 600(H) 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security. This must be greenguard certified.

Supply and Installation of Three-Seater Sofa • SEAT FOAM: The seat is made of PU foam with Density 28± 2 kg/cu. meter having an additional top layer of super soft PU foam in Density 32 ± 2 kg/cu.

upholstered with fabric or leatherette. Seat Cushion Thickness ±3 (mm): 150mm

• 2) BACK FOAM: The back is made of PU foam with Density 28 ± 2 kg/cu. meter with two additional top layers of super soft foam of density 32±2 kg/cu. meter, upholstered with fabric or leatherette.

3 SEATER SOFA IN HOD CABIN & Backrest Cushion Thickness ±3 (mm): 175mm

2 WAITING AREA • 3) UNDERSTRUCTRE: Under structure is made up of 1.2±0.1 cm. thick hot-pressed plywood (moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & Each 1 2 2 2 2 2 11 38950.00 428450.00

Size : 1980(W) X 900(D) X 850(H) surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over under structure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over under

structure for cushioning purpose.

• 4) LEG ASSEMBLY: It is a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic end cap. (W) 2060mm (D) 905mm(H) 855 mm seat (H) 450 mm, Sofa Leg Height ±2(mm): 150

mm, Sofa Leg Width / Diameter ±2 (mm): 40 mm, Arm Height ±5 (mm): 710mm, Arm Width ±5 (mm): 120mm, Sofa: as approved by Engineer In-Charge/employer.

Supply and Installation of Two-Seater Sofa SEAT FOAM: The seat is made of PU foam with Density 28± 2 kg/cu. meter having an additional top layer of super soft PU foam in Density 32 ± 2 kg/cu.

upholstered with fabric or leatherette. Seat Cushion Thickness ±3 (mm): 150mm

• 2) BACK FOAM: The back is made of PU foam with Density 28 ± 2 kg/cu. meter with two additional top layers of super soft foam of density 32±2 kg/cu. meter, upholstered with fabric or leatherette

Backrest Cushion Thickness ±3 (mm): 175mm

2 SEATER SOFA IN WAITING AREA

3 • 3) UNDERSTRUCTRE: Under structure is made up of 1.2±0.1 cm. thick hot pressed plywood (moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & Each 1 0 0 0 0 0 1 31950.00 31950.00

surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over under structure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over under

structure for cushioning purpose.

• 4) LEG ASSEMBLY: It is a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic end cap. (W) 1460mm (D) 905mm(H) 855 mm seat (H) 450 mm, Sofa Leg Height ±2(mm): 150

mm, Sofa Leg Width / Diameter ±2 (mm): 40 mm, Arm Height ±5 (mm): 710mm, Arm Width ±5 (mm): 120mm, Sofa: as approved by Engineer In Charge/employer.

SIDE TABLE IN HOD CABIN &

Supplying and placing Centre Table. It shall be of Dimensions 1100mm x 600mm x 460mm with 10 mm tampered glass top. It shall also have 8mm thick tampered bottom glass for storage option. It shall

have Chrome plated understructure. It must have Passed 48 hours salt spray test. athe Glass is attached to the understructure via UV disc. It Load bearing capacity shall be 30Kg UDL.

Supply and Installation of discussion table with size: 1800 mmLx1200mmWX750mmH, Work Top-Made of Work top shall be made up of 32 mm thick E-1 grade (Environmentally Friendly) pre-laminated

MDF board conforming to as per IS 14587: 1998, Grade II corresponding to IS 12406:2003 with 1.0 mm thick laminate E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven

dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992), all the edges of worktop shall be provided with machine pressed 1.5-2 mm thick PVC edge

banding tape pressed at 200o C with hot melt glue on special machines. Access panels provided with soft closing hinges.

MEETING TABLE, Size : 1800(W) X Under structure-The Under-structure consists of mixture of 25mm thick E-1 grade (Environmental Friendly) pre-laminated MDF board conforming to as per IS 14587: 1998, Grade II corresponding to IS

900(W) X 750(H) 12406:2003 with 1.0 mm thick laminate E1 grade laminate. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down

construction. Wire management: a Wire tray in with integrated power box made with a combination of 0.8 mm thick CRCA sheet and 0.8 mm thick CRCA switch plate, auto flip up electric box with

dimension: 300mm x 158mm x 70 mm shall be provided at table top with includes unit: 2 Universal Power Socket, 2 USB Fast Charger (Type A + Type C) and 2 HDMI. Meeting table as approved by

engineer in-charge/employer.

Providingin place of main table with overall size of table 1500 x 750 x 750mm. The main worktop shall be 1650 x 750 x 750mm and Side unit shall be 900 x 500 x 750mm. The table is made of 25 mm

SENIOR SCIENTIST CABIN, Main thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for

Table : 1500(W) X 750(D) X 750(H) wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25

Side Unit : 900(W) X 450(D) X mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2

750(H) grade and approved shade confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

Pedestal : 400(W) X 450(D) X approved shade confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998

600(H) with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers

have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security. This must be UL greenguard certified.

Body panels are made of 18 mm thick ISI marked Commercial plywood (Moisture Resistant grade plywood) faced with 1.0 mm thick laminate on both sides, All the exposed edges are edge banded with

2 mm thick PVC edge banding. Openable Doors/Sliding Doors shall be made of 18 mm thick ISI marked Commercial plywood (Moisture Resistant grade plywood) faced with 1.0 mm thick laminate on

both sides all the exposed edges are edge banded with 2 mm thick PVC edge banding.

Side panel are made of 18 mm thick ISI marked Commercial plywood (Moisture Resistant grade plywood) faced with 1.0 mm thick laminate on both sides, all the exposed edges are edge banded with 2

7 Prelmainted MDF STORAGE mm thick PVC edge banding, 5 nos. Drawer/shelf components shall be made of 25mm thick ISI marked Commercial plywood (Moisture Resistant grade plywood) faced with 1.0 mm thick laminate on

both sides. All the exposed edges are edge banded with 2 mm thick PVC edge banding. Body back and drawer bottom are made of mm 18 thick ISI marked Commercial plywood (Moisture Resistant

grade plywood) faced with 1.0 mm thick laminate on both sides. Hardware: The high-quality hardware like Roller slides, SS Hinges, Mini fix, SS Handles, 3-way locks, wooden dowels, screw, shall be used

of Hettich, EBCO make or equivalent or as approved by engineer in charge/employer. Commercial plywood and Laminate Make: Century/Action Tesa/Green Ply or equivalent/or as approved by

engineer in-charge/employer), Wooden Wardrobe as approved by engineer in-charge/employer.

Digitally signed by MAHABIR

Providing and placing of Steel Almirah overall size: 916mm(W)x486mm(D)x1980mm(H) with welded construction. Almirah shall be made of CRCA ‘D’ grade high yield strength, CRCA sheets conforming

to grade as per CRI of IS 513 (part-1):2016, It should have 4 Nos. shelves with thickness of 0.6 mm, Back thickness of 1.0 mm, Door thickness of 0.6 mm (high yield strength) and stiffener shall be

provided in door up to full height, Width of stiffener: 115 mm, Stiffener sheet thickness: 0.8 mm and all other components shall have thickness of 0.6 mm. The Steel Almirah should have a Mazak

8 ALMIRAH handle and Three-way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly distributed load (UDL) for shelves: 80 Kg. Almirah also Each 0 0 2 2 2 2 8 24950.00 199600.00

have a M10 Screw type Leveller with Hex plastic base, Number of hinges (for each door): 03 Nos. Hinges sheet thickness: 2 mm,Pedestal height (± 5 mm): 125 mm, The finishing shall include Epoxy

powder coated with thickness of 50 microns (+/- 10%).Powder coating: Conforming to IS: 13871. . The product should be complete and as per sample approved & as per direction of Engineer-in-

charge/employer.

MAIN TABLE of size 1200W x 600D x 750H MM with top made of with top made of 25mm thick Pre-laminated MDF board and balancing laminate on unexposed face. The Gable end is

P.A./SECURITY STAFF made up of 25mm thk. pre-laminated MDF board. The understructure is made of 18mm thick prelaminated MDF board with all exposed edges sealed with 2mm PVC edge banding tape and

CABIN/SAMPLE all unexposed edges sealed with 0.6mm edge banding tape pressed at 200o C with hot melt glue on special machines. Table has a provision for wire manager caps at top. Providing & Fixing

COLLECTION/RECEPTION,/TEACHI mobile pedestal size- 400(L)x450(D)x685(H)mm with 2 drawer & 1 filling. The drawer unit is made of 18mm thick prelaminated MDFe board with all exposed edges sealed with 2mm Each 3 4 4 4 4 4 23 18950.00 435850.00

NG/ LAB DEMONSTRATION HALL thick PVC edge banding tape and unexposed edges sealed with 0.6mm PVC banding tape pressed at 200o C with hot melt glue on special machines. The inner drawer is made of 0.6mm

TABLE Size: 1200(W) X 600(D) X CRCA steel duly powder coated & has proper locking

750(H) arrangement with drawer sliding on nylon rollers channels. The drawer unit with 4 nos. nylon castors.

All, Hardware ( Handles, Slides ,Hinges ) Hettich Make.

The seat and back to be made up of high-density self-skin 25-30mm thick PU Foam reinforced with 1.2 mm thick MSperforatedsheetinsert.ThePUFoamhavingdensityof680+/-10Kg/m3with hardness of

55 +/-5. Seat Size :52.0 cm (W) X 46.5 cm (D). Back Size: 52.0 cm (W) X 51.5 cm (H). Floor to seat height (front) minimum: 410mm, Overall length (minimum): 1680mm, Cross Beam made up of black

powder coated MS ERW square tube of size 6.0+/- 0.05cm X 6.0+/- 0.05cm X0.4+/-0.016 cm thick fitted with polypropylene end caps. Thickness of the seat support and lumber support (minimum):

23mm, Legs & Armrest made up of powder coated High pressure Aluminium Die cast Powder coated with minimum 70 microns. Number of armrests: 04 Nos. Thickness of material of Arms 1.8 mm,

Thickness of material of Legs 2.0 mm, Legs are fitted with soft grip PVC level adjusting shoes. Main frame finish with Powder coated of minimum 50-70microns, 3-

seaterwaitingchairasapprovedbyengineerin-charge/employer.

Worktop shall be made out of 25mm thick Exterior Grade Pre-Laminated particle board. All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with

OFFICERS CUBICLES, 60mm Panel hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Worksurfaces

1200H, Main Table : 1500(W) X are fitted to the panels by worksurface brackets, wooden legs & wooden modesty. Brackets are made of 2.0mm thick CRCA grade D steel as per IS : 513. Brackets are slide in between end trim and

750(D) X 750(H) vertical extrusions..Panel: Frame work shall consist of main spine and return spine of aluminium extruded section of minimum thickness of 1.2 mm. The thinkness of main & return Panel is 55-60 mm .

11 Side Unit : 1050(W) X 450(D) X The panel will be hollow inside to accommodate wiring for electrical/data and outer frame of panel should be made of extruded aluminium, cladding with 3mm thick MDF both sides of the panel to Each 0 0 2 2 2 2 8 38950.00 311600.00

750(H) create the hollow for the wire management. On the MDF 0.5-0.6 mm fabric / Steel CR 0.5.06 mm EPC/ EPF Foam 3-4 mm for pin up as an option based on the requirement and as per approved by

Pedestal : 400(W) X 450(D) X Engineer-In-Charge.For the glass panel different aluminium profile (Top and bottom of the frame) with 60-70 mm thick which should accommodate the glass of thickness 4-6 mm.Finishes of panel:

600(H) Above the top fabric pinup & Glass writable board with raceway in main spine (return table) & fabric pinup (Main table) & balance fabric finish for ailse side & return panel, below the top should be

metal with MDF tile with one raceway at skirting level and etc whichever required.

Supply Installation of linier workstation size 1500mmWX600mmD x1200-1250mmH Providing and placing of modular partitions system coated aluminium trims and supported on Legs for better air

circulation and helps in keeping floor clean. Panels Construction - Each panel consists of Vertical extrusions 2Nos and Horizontal extrusions made of 1.2mm thick aluminium with duly powder coated at

every division of tile/block. Each panel have Bottom frame fabricated for 52.4mm panel comprises of L-channels made of 2mm thick CRCA steel (IS: 513), formed plates of 3mm thick HR steel (IS: 2062)

& ERW steel tube of size 35x15x1.6mm thick in oval cross section (IS: 7138) welded together. The complete bottom frame shall be powder coated with an average of 50-60 microns thickness of epoxy

powder coating. The Bottom Frame is bolted with the Upright verticals. Each Panel is provided with 2Nos Legs of height 120mm are fixed at the bottom frame of the panel. Legs are fabricated by CO2

welded MS Tube of section 38mm x 25mm (IS: 7138 ERW Tube, 38mm x 25mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5mm HR) over which an M8 Leveller is fitted which

allows for adjustment of the height by 50mm. It will be coated with 45-50micron thickness of epoxy powder coating. Each Panel consists of 2Nos Intermediate blocks. In a 52.4mm Thick panel

intermediate block shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm decorative laminate on both sides. Particle board framing shall be used on outer

boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks will be located in the middle bands of the panels made out of a composite

construction of MDF and paper honeycomb. Each Panel consist of TOP TILES/SPLIT TILES. These tiles shall be slide in to the panels from top before fixing the top horizontal. These tiles shall be

supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. In case of split tiles it shall be offered in Fabric magnetic tiles, Whiteboard tiles. Each Panel

consists a BOTTOM TILE. These bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap-on clips made of nylon-66 and support clips made from Polypropylene (PP).

All partitions and side panels have levelling screws for adjustment in case of uneven floor to take care of +/- 40 mm of uneven flooring. Tile Finishes:

a FABRIC MAGNETIC TILES: Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with adhesives.

• FABRIC TACK TILES: Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with Polyurethane foam in the tile for tackablity. The fabric shall be upholstered

with adhesives.

• WHITE BOARD TILES : White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm

backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging. Aluminium Trims: The top trims and end trims for 52.4 mm shall be made from aluminium

extrusion. All kinds of extrusions for 52.4mm shall have average wall thickness of 1.2 mm & having finish of powder coating.

Top trim in 52.4mm thick panel shall be press fitted on the horizontal extrusion, it shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade.

End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513.Wire Management - Wires shall be taken into the

system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Wires runs through the system from Bottom tile and extended to

the top at various locations by the help of 2 nos. vertical Cable Ducts in each panels.

Cable duct shall be made from 0.8 mm thick M.S. CRCA Grade D as per IS: 513 - 1994. It is constructed with two parts; one is body & another is cover. It holds the cables & gives aesthetic appearance by

covering all cables entry, which are moving upward to the panels. Size of Cable duct is 107mm W X 154 mm H X 21 mm D. Telephone and Electric fitting materials for each work station:- Plate and

frame 8M & 2M, 16 Amp switch 1M, 6A-3Pin socket, 6/16A Socket, Blanking plate 1M, RJ-45 CAT 6UTP, RJ-11 Telephone and wire 3x2.5 mm Square, Makes for copper wire: Havelles/Polycab/RR Cable

or as approved by engineer in-charge/employer, Make for Modular switches and Sockets outlet: Legrand-Myrius or anti-bacterial/ABB (Tvisha)/ Panasonic/Schneider-Livia/Philips-sleek or as approved

LINEAR WORKSTATIONS IN DIV.

by engineer in-charge/employer, All electric/telephone fitting with materials shall be carried out by the supplier for each work station as per client requirement. Legs - System shall also have 120 mm

STAFF, 60mm Panel 1200H, Main

12 high powder coated welded metal legs to give the system an elevated look. Single side legs are fabricated by CO2 welded MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x Each 0 0 8 8 8 8 32 28950.00 926400.00

Table : 1350(W) X 600(D) X 750(H)

16bg) with the base plate of the MS plate of 35mm x 22mm x 5mm (IS: 2062, 5 mm HR) over which an M8 Leveller is fitted. End/Intermediate separator: partitions of 22.8mm thick including powder

Pedestal : 400(W) X 450(D) X

coated aluminium trims and supported on Legs for better air circulation and helps in keeping floor clean. The 22.8 mm panels are only to be used as Separator/End panels to provide additional privacy.

These panels have various finishes and no cable management ability. Panel Construction: The 22.8mm End/Separator panels shall be made of horizontal and vertical uprights. These uprights and

horizontals shall be made of aluminium extrusion having material AL96063-T6 & have average wall thickness of 1.2mm & powder coated with epoxy-polyester powder. The Blocks for the End/Separator

panels shall be of 16mm to 18mm thickness in the selected finish. The top most block in the panel shall be the top block of the panel. It shall be available in fabric, laminate, whiteboard, fabric metal,

trackable and clear glass finishes. The 2Nos blocks in the intermediate bands shall be available in fabric or laminate finish and the lowermost block in the panel shall be the bottom block which shall be

in fabric, metal or laminate finish. Tiles : Tile Finishes in End/Separator Partitions to be provided as per the site and layout approval. Finishes in these panels shall be

• LAMINATE FINISH BLOCKS:

Laminate finish blocks shall be made from 18mm thick MDF board, cladded with 1mm thick laminate of approved shade.

• FABRIC FINISH BLOCKS:

These shall be made from 18mm thick Pre-Laminated MDF Board upholstered with 1mm thick approved shade of fabric using adhesives.

• WHITEBOARD BLOCKS:

These shall be made of 16mm thick MDF board laminated with 0.6mm thick white glossy high pressure laminate on both sides and having all its edges with minimum 0.5 mm thick PVC edging.

• GLASS BLOCKS:

These shall be made of 4mm thick toughened plain glass having diamond polish edge finish.

• FABRIC TACKABLE BLOCKS:

These shall be made from 18mm thick Pre-Laminated MDF Board battens which hold 3mm MDF in between. 6mm thick Polyurethane foam shall be pasted on 3mm thick MDF and this assembly shall be

upholstered with approved shade of fabric on both sides using adhesive.

• METAL FINISH BLOCKS:

Metal finish blocks shall be made from two components of 0.8mm thick M.S. CRCA Grade D as per IS: 513 powder coated with epoxy polyester finish. AluminiumTrims : The top trims and end trims for

22.8mm partition shall be made from aluminium extrusion having material AL96063-T6. Top trim in 22.8mm thick panel shall be slide fitted with the help of top trim connector made from PP

copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick

panel shall slide with the help of end trim connector made from nylon-66. Work station Worktop as per the approved shape and site requirement made out of 25mm thick prelaminated MDF board.

All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm

as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Worksurfaces are fitted to the panels by worksurface brackets. Brackets are made of 2.0mm thick CRCA

grade D steel as per IS : 513-19. Brackets are slide in between end trim and vertical extrusions. computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA steel as per IS : 513I

made of 0.9mm thick powder coated with sliding channels and other fixtures/fittings. It should also have a sliding system for accommodating mouse. CPU Trolley of Size - 345mm(W) x 226(D) x

180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-lockable twin wheel castors are injection moulded in Black Nylon.

Digitally signed by MAHABIR

panels shall be of 16mm to 18mm thickness in the selected finish. The top most block in the panel shall be the top block of the panel. It shall be available in fabric, laminate, whiteboard, fabric metal,

trackable and clear glass finishes. The 2Nos blocks in the intermediate bands shall be available in fabric or laminate finish and the lowermost block in the panel shall be the bottom block which shall be

in fabric, metal or laminate finish. Tiles : Tile Finishes in End/Separator Partitions to be provided as per the site and layout approval. Finishes in these panels shall be

Sr. no. Name of Items Laminate finish blocks shall be made from 18mm thick MDF board, cladded with 1mm thickItem Description

laminate of approved shade. UNIT G.F 1st 2nd 3rd 4th 5th Rate (Rs.) Amount (Rs.) Reference Image

• FABRIC FINISH BLOCKS:

These shall be made from 18mm thick Pre-Laminated MDF Board upholstered with 1mm thick approved shade of fabric using adhesives.

• WHITEBOARD BLOCKS:

These shall be made of 16mm thick MDF board laminated with 0.6mm thick white glossy high pressure laminate on both sides and having all its edges with minimum 0.5 mm thick PVC edging.

• GLASS BLOCKS:

These shall be made of 4mm thick toughened plain glass having diamond polish edge finish.

• FABRIC TACKABLE BLOCKS:

These shall be made from 18mm thick Pre-Laminated MDF Board battens which hold 3mm MDF in between. 6mm thick Polyurethane foam shall be pasted on 3mm thick MDF and this assembly shall be

upholstered with approved shade of fabric on both sides using adhesive.

• METAL FINISH BLOCKS:

Metal finish blocks shall be made from two components of 0.8mm thick M.S. CRCA Grade D as per IS: 513 powder coated with epoxy polyester finish. AluminiumTrims : The top trims and end trims for

22.8mm partition shall be made from aluminium extrusion having material AL96063-T6. Top trim in 22.8mm thick panel shall be slide fitted with the help of top trim connector made from PP

copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick

panel shall slide with the help of end trim connector made from nylon-66. Work station Worktop as per the approved shape and site requirement made out of 25mm thick prelaminated MDF board.

All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm

as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Worksurfaces are fitted to the panels by worksurface brackets. Brackets are made of 2.0mm thick CRCA

grade D steel as per IS : 513-19. Brackets are slide in between end trim and vertical extrusions. computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA steel as per IS : 513I

made of 0.9mm thick powder coated with sliding channels and other fixtures/fittings. It should also have a sliding system for accommodating mouse. CPU Trolley of Size - 345mm(W) x 226(D) x

180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-lockable twin wheel castors are injection moulded in Black Nylon.

The seat should be made up of 1.2 ± 0.1cm. thick hot pressed plywood and upholstered with leather and moulded Polyurethane Foam. The back foam should be designed with contoured lumber

support for extra comfort. BACK SIZE: 53.0cm.(W) X 95.4cm.(H) .SEAT SIZE:

54.6cm.(W) X 49.0cm.(D): The HR polyurethane foam should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.The seat and back should be arrested together

with spine made of 0.8 ±0.05 cm thk HR Steel and should be black powdercoated ( DFT 40-60 microns ). The armrest assy. should comprise of three parts viz. the armrest support tube and P.U. armrest

and the armrest top. The armrest tube assy. should be made of 2.54±0.03cm x 0.16±0.0128cm M.S. E.R.W. support tubes and Chrome plated. The P.U. armrest should be made of black integral skin

polyurethane with 50-70 shore 'A' Hardness and reinforced with M.S. insert. The armrest top should be made of ABS & upholstered with foam & leather. The mechanism should be designed with the

HIGH BACK CHAIR FOR HOD

•Front pivot for tilt with feet resting on ground ensuring more comfort. •Tilt tension adjustment.

•5-position locking with anti-shock back mechanism, which prevents the backrest from

impacting the user when the lock should be released . •Static seat depth adjustment = 5.0 ± 0.5cm with 5 position locking. it has an adjustment stroke of 9.0 ± 0.3cm. The bellow should be 1 piece and

blow moulded in black Polypropylene. The pedestal should be made of die-cast aluminium with buffing finish. It should be fitted

with 5nos. twin wheel castor. The pedestal should be 67.0 ± 0.5cm pitch-center dia. (77.0 ±

1.0cm with castors). The twin wheel castors should be injection moulded in black Nylon.

The seat should be made up of 1.2 ± 0.1cm. thick hot pressed plywood and upholstered with leather and moulded Polyurethane Foam. The back foam should be designed with contoured lumber

support for extra comfort. The chair should be available in three models: BACK SIZE: 53.0cm.(W) X 73.0cm.(H)SEAT SIZE: 54.6cm.(W) X 49.0cm.(D) The HR polyurethane foam should be moulded with

density = 45 ±2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.The fixed type mechanism should be made with a 0.8 ±0.05 cm thk HR Steel spine welded to it and black powder-coated ( DFT

40-60 microns ).The Understructure should

be made up of M.S.E.R.W. Elliptical tube of size 4.5 ± 0.03cm x 1.9 ± 0.02cm x 0.25 ± 0.025cm welded to M.S.E.R.W Tube of ∅ 1.6 ± 0.02cm x 0.2 ± 0.016cm thk. The understructure should be powder

coated ( DFT 40-60 microns ) in Silver metallic gray

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity yarn. Seat Size:- 47cm(w) ×

51.5cm (D). The HR polyurathene foam is moulded with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm

which is provided in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is made up of plastic injection moulded nylon with textured top. It shall have Front

MID BACK CHAIR FOR MEETING

15 pivot synchro mechanism with following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting Each 6 5 5 5 5 5 31 12,500.00 387500.00

ration of 1:2. The lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted through two projecting

knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions

recieved from Engineer Incharge. It shall be SCS IAQ certified for Indoor Air Quality.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity yarn. Seat Size:- 47cm(w) ×

51.5cm (D). The HR polyurathene foam is moulded with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm

HIGH BACK CHAIR FOR SENIOR which is provided in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is made up of plastic injection moulded nylon with textured top. It shall have Front

16 SCIENTIST CABIN/OFFICER pivot synchro mechanism with following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting Each 1 3 4 4 4 4 20 12,950.00 259000.00

CUBICALS ration of 1:2. The lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted through two projecting

knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions

recieved from Engineer Incharge. This shall come along a headrest from same family. It shall be SCS IAQ certified for Indoor Air Quality.

The Seat is made of 1.4cm thick hot pressed plywood upholstered with fabric and moulded Polyurethane foam. It has a seat depth adjustment of 5cm integrated in the seat through a sliding

mechanism. Seat size shall be 550cm x 49cm. The back is injection moulded in Glass filled polyamide which is upholstered with Mesh fabric. The back consist of adjustable lumbar support made of

VISITOR CHAIR FOR SENIOR

injection moulded polypropylene having an adjustment of 6cm. Back size shall be 50cm x 68cm. The Polyurethane foam for seat is of density 55 kg per meter cube. The three way adjustable armrests is

made of glass filled polyamide arm structure with PU armtop and height adjustment of 7cm. The armtop has swivel and to and fro motion. The inner tube of armrest is chrome plated. The chrome

plated tubular frame is made of dia. 2.8cm x 0.2cm thick MS round tube. The frame is fitted with Plastic caps made of injection moulded glass filled Polypropylene. The overall dimensions of the frame

shall be 63.5cm x 59.5cm x 97.5cm. The seat height shall be 42.5cm.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using net fabric with high tenacity yarn. Seat Size:- 47cm(w) ×

MID BACK CHAIR FOR SECURITY 51.5cm (D). The HR polyurathene foam is moulded with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm

STAFF which is provided in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer. Armrest is made up of plastic injection moulded nylon with textured top. It shall have Front

18 CABIN/RECEPTION/EACHING/ LAB pivot synchro mechanism with following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back tilting Each 3 4 12 12 12 12 55 12,500.00 687500.00

DEMONSTRATION HALL /LINEAR ration of 1:2. The lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted through two projecting

WS/CABIN knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions

recieved from Engineer Incharge. It shall be SCS IAQ certified for Indoor Air Quality.

The seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade UV Resistance. The Powder coated (DFT50+ microns) weled tubular

frame is made from 2.22 + 0.03 cm x 0.16+/- 0.0128cm and 3.5+/- 0.03 cmx1.5+/-0.03 cm x 0.16 +/- 0.0128 cm M.S.E.R.W tube.The powder coated weled beam M.S. Structure is made from 5.08+/-

0.03cm x0.16x +/- 0.0128 cm.The Shoes are made of high impact strenght polypropylene polymer compond with indoor grad UV Resistance and pressed fitted with tubularfram. The Armrest made of

high impact strenght polypropylenne polymer compound with indoor grad UV resistance and assembly over the tubular frame. The "L" Shape Desket is made of 1.8+/- 0.05cm thk . pre - laminated

Perticleboard with 0.2+/- 0.05 cm thk injection polypropylene polymer all around Front & Back ( outher Dimension - 31.5+/-(W)x 47.0+/- 0.1 cm (D)) An Upholstry cover be retro fitted on seat and back

19 TRAINING CHAIRS . the seat cover is made fromhigh abrasion resistance with fabric with foam laminated and 2.5cm PU Foam insert. the back cover is made from HIgh Abrasion Resistance fabric with foam lamination and Each 0 20 20 20 20 20 100 7,450.00 745000.00

0.1 cm PU foam .

SIZE : (W)57.5cm*(D)67.8cm*(H)84.5cm*(seat H) 45.0 cm

Seat Size 52.5cm(W)*53.2 cm(D)

Back Size 51.6 cm(W)*40.5 cm (H)

Digitally signed by MAHABIR

Supply and installation of stool as per technical specification. The seat shall be made up of 1.2±0.1cm thick flat plywood measured as per QA method described in OCP-QLTA-P14-18 and with moulded

Polyurethane foam and are upholstered with replaceable synthetic leather covers. The dimensions of Seat shall be Diameter 40.0 cm

and Adjustments are 360° Revolving type. The back foam shall be designed with contoured Lumbar support for extra comfort. The upholstery shall be available in synthetic leather. The dimensions of

Back shall be 45.0 cm (W) covered with polyurethane foam. The HR polyurethane Foam shall be moulded with density = 45 +/-2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.

20 LAB STOOL The manual height adjustment shall be very easy to operate with a help of a knob. It should be easily locked at the most comfortable position. The five-prong pedestal shall be fabricated from 0.2 ± Each 40 40 40 40 45 45 250 6,950.00 1737500.00

0.02 cm thick HR sheet (IS : DD 1079/ HR ), Powder coated ( DFT 40-60 microns ) and shall be fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The pedestal

shall be 55.0±0.5cm pitch-circle diameter (65.0±1.0cm with castors). Circular-foot-ring ofDia 52.0±0.2cm shall be made up of 01.9±0.2 x 0.12±0.0096cm thk MS ERW Tube for foot support in High-

base stool. The twin wheel castors shall be injection moulded in Black Nylon. Overall dimensions shall be Width- 65.0cm, Depth- 65.0 cm, Seat Height- 45.0 to 56.5cm. Stool as approved by engineer in-

charge/employer.

1. Racks are required to store samples/kits in walk-in deep freezer (-20oC to -40oC) and walk-in refrigerator (+2oC to +8oC).

2. The racks should be easy to assemble, adjust or configure.

3. The individual racks should have wheels to facilitate easy mobility and lowest shelf should be approximately 6-8 inches above the ground.

4. There should be gap of approximately 1 – 3 feet between two shelves.

5. Topmost shelf should be at least 2 – 3 feet from the roof.

21 Storage Rack for cold Rooms 6. The racks should be made from lightweight, non-corrosive, rust proof and extremely durable metallic material (composite). Each 10 10 10 10 10 50 41,500.00 2075000.00

7. The racks should be easy to clean with routinely used cleaning solutions.

8. The racks should be resistant to scratching, peeling and corrosion.

9. The racks should withstand temperatures as cold as -35ºC and warm environments up to +50ºC.

10. The racks should have warranty for a period of five years.

Size specifications:

4 shelf Shoe rack should made up of SS 304 ,Height of shoe rack: 1200 mm (±10 mm), Width of shoe rack: 950 mm (±10 mm), Depth of shoe rack: 380 mm (±10 mm), Frame sizes: 25 mm X 25 mm X 1.2

mm(thick), Distance between each shelves ±10 mm: 300 mm, Ground clearance: 100 mm (±10mm), Thickness of Side/Back/Top sheet Covering material: 1.0 mm thick Stainless steel (SS-304 grade),

Shelves thickness/size: 0.8 mm thick Stainless steel sheet of 304 grade, Welding: Frame pipes and sheet work to be welded with MIG welding and buffed/grind neatly, Should have a dust tray to collect

the dust , shoe rack to keep 24 pair of shoes (max 4 tier). Shoe Rack (24 Pairs) as approved by engineer in-charge/employer

Supply and Installation of 4 Door Personal Locker Unit (Base) with size of 450mm(W)x480mm(D)x1900mm(H) (± 5 % ) Stiffened pedestal height shall be 75 mm, Number of compartments shall be 4.

Stack ability shall have add - on units that can be stacked width wise to form bank of locker shaving common side panel. Non-welded hinges with removable hinge pins should be provided. Locking shall

have 10 Lever cam lock with lock lever plus option of hasp arrangement and duplicate key should be provided. Material shall be CRCA Sheet. sheet thickness of body, back, shelves, pedestal and door

23 4 Door Personal Locker must be 0.8mm thick. Construction shall be Rigid Knockdown construction; the uniformly distributed load capacity of shelves shall be 40 Kg minimum. Finish shall be epoxy polyester powder coated Each 10 10 10 10 10 50 27,500.00 1375000.00

with 50-60microns thickness. Handle/Label holder shall be Electroplated Mild Steel handle/label. Ventilation shall be attractive punched pattern for ventilation. Or As approved by engineering-

charge/employer.

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyester fabric. The back size

shall be 45.5cm W x 53.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly connected to the base frame and are

cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat

offers impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine

24 Workstation Chair connector moulded in glass filled Polyamide form the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Each 25 25 25 25 25 25 150 11,500.00 1725000.00

limiter feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded

in glass filled Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors. The

pedestal is 66cm pitch centre diameter and 76cm with castors. The overall dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm). This must be UL

Greenguard certified and AIOTA certified for ergonomic health.

Digitally signed by MAHABIR