ADDN/ALTN TO BLDG NO. P-5 AT AF STN NAJAFGARH UNDER GE (AF) TUGHLAKABAD

Amount

Dismantling of old brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by Engr-in-charge.

Demolition of existing mud in roofs of any thickness including plastering, old APP sheet and leaping, whether full thickness removed or only a part there of, and removing mud, all rubbish material outside of defence Land as directed by Engr-in-charge.

M&L for PCC (1:2:4) type B-0 ( using 12.5 mm graded stone aggregrate ) laid over roof slab after applying cement slurry for filling undulationations finished even and smooth without using extra cement complete all as spd and directed.

M&L for applying cement slurry over existing roof surface @ 3 Kg/Sqm complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4 (mixed with WPC @ 3% by weight of cement) to brick/concrete wall and roof surfaces finished even and smooth (without using extra cement) with water proofing compound at the rate of 3% by weight of cement or as per the manufacturer’s instructions complete all as specified and directed by Engr-in-charge. Note: WPC shall be measured and paid for separately

Supply only integral water proofing compound complete all as specified and directed by Engr-in-charge.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured as per approved make by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions complete all as specified and as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with fly ash modular bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for brickwork with fly ash bricks, straight or curved on plan to ant radius in half brick thick wall, built in built in CM 1:4 complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:6 on stone masonry surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to stone masonry wall surfaces or on other than fair faces of brick masonary finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed by Engineer-in-Charge.

M&L for Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed.

S&F mild steel framed work as in ladders, cages and similar work including welding complete all as specified and directed.

S&F in repair Prelaminated particle board 18 mm thick, interior grade, ISI marked as in cupboard shutter / shelves, prelaminated one side with decorative choice lamination and other side balancing white lamination including 6mm thick teak wood liping, fixed with screws to timber frame work complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Powder coated Anodised aluminium frame and grill for doors, windows ventilators with one or more rebates including joining cleat for fixing etc.complete all as specified and directed.

S&F of aluminium powder coated of any colour (thickness or powder coating not less than 50micron) doors shutters aluminium saction weighing 0.55 kg/sqm including necessary jointing cleats, glazing clips, rubber neoprene packing, handles two nos in each door, hinges, anodised aluminium snap beading, screws complete all as specified and directed.

S&F Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weeighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fitings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Supply and fixing powder coated (thickness of powder coating not less than 60 micron) aluminium grill of design DG-104 pattern, made out of 10mm dia rod fixed with and including stranded aluminium frame of 'F' section of size 23.04x15.3x1.4mm thick all as manufacturer's instructions complete all as specified and directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, with and including taking down & refixing the aluminium door shutter, complete all as specified and directed.

S&F 5.5 mm thick Sheet glass, ordinary quality and glazing in Aluminium windows completed all as specified and directed.

S&F fixed galvanized mild steel wire cloth 0.56 mm nominal dia of wire & average width of aperture 1.18mm & fixed with tinned tacks or galvanized wire staples in door and steel window all as spd and directed

S & F 100 mm size Butt hinges, extruded aluminium alloy with galvanished mild steel hinges pin, anodized & fixed, type B-21 completed all as specified and directed

S&F 125 mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 125 mm long Aluminium tower bolts, stove enamelled black, with bright bolt and fixed completed all as specified and directed.

S&F 300mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller plate welded to mild steel frame fixed in repair completed all as specified and directed.

S&F 250 mm long mild steel sliding door bolts plate type stone enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed

S&F fixed in repairs galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples in door and steel window complete all as specified and directed

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed.

S&F hasp and staple of size 100mm safty type of aluminium and andosied including bolts to hinges plate and fixed with screw complete all as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material outside of defence Land complete all as specified and directed.

M&L 10 mm thick rendering in cement mortar 1:4 to stone masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair and even without using extra cement for fixing tiles etc complete all as specified and directed.

M&L 450x350x7/350 x 250 x 7mm thick glazed ceramic coloured tiles as in vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B-1, ( using 25 mm graded stone aggregate) as in floors, surfaces finished fair and even complete all as specified and directed.

M&L 15 mm thick screed bed or bedding layer of mortar, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L 20 mm thick screed bed or bedding layer of mortar, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8mm thick (square / rectangular ) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and directed by Engineer-in-Charge.

M&L Vitrified ceramic light shade coloured tiles 10mm thick area of each tiles not exc 0.36 sqm , in floor etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match the shade of the tile complete all as specified and directed by Engineer-in-Charge.

M&L for 16 to 18 mm thick Granite (of any tpe) work (tablee rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

M&L Green Marble of work 25mm thick (table rubbed and polished) in cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following type complete all as specified and directed by Engineer-in-Charge.

Rounding and grinding of edges of kota stone/Granite/Green marble as on steps/cooking platform/cill etc all as specified and dircted by Engr-in-Charge.

M &L 100 mm thick PCC (1 :4:8) type D-2 ( using 40mm aggregate ) as in sub base in floor complete all as specified and directed

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge..

M&L Machine Pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS- 15658-2006 of 60 mm thickness M-35 grade complete all as specified and directed by Engineer-in-Charge.

M&L Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 (using 40 mm graded stone aggregate) as in plinth protection/path/paving laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

Taking up or down15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge.

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge.

Dismantling water tank and removing to store exc 250 ltr but n exc 500 ltrs complete all as specified and directed by Engineer-in-Charge.

S&F Steel water tubing ISI marked , galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor 15 mm dia of pipe complete all as specified and directed by Engineer-in-Charge

S&F steel water tubing ISI marked , galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor 20 mm dia of pipe complete all as specified and directed by Engineer-in-Charge

S&F 1000 litres, rotational moulded polyethylene water storage tank ISI marked triple layer (Cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore ball brass valve ISI marked, high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including fixing cantilever brackets coupling and waste pipe and connecting union to pipe overall size 1200mm x 460mm bowl size 410mm x 330mm x 200mm complete all as specified and directed.

S&F stainless steel utensil plate rack of size 900x1000x200 mm, made of 0.60 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F toilet cabinet with mirror of overall size 350 x 450mm complete all as specified and directed.

S&F vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia, 450 mm long HDPE PVC connection, 32 mm dia wast coupling and 32mm bore Waste coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement including CI brackets all directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern) white with "P" or "S" Trap front or back inlet fixing bols, PVC seat cover closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making all necessary connection complete all as specified and directed.

S&F in repair vitreous china squatting pan ORRISA pattern, size 580x440mm white, with integral foot rest including provn of concrete bedding and connection to trap and flushing pipe antisyphonage pipe etc comple incl making good to floor complete all as specified and directed.

S&F in repair PVC valve less symphonic action type, flushing cistern, low level, white of capacity 10 ltrs with inlet , ball valve, float and handle including brackets complete all as specified and directed.

S&F chromium plated brass tubular towel rail 20 mm dia, D type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed.

S&F in repair 15mm bore angle valve ISI marked cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F 20mm bore stop valve ISI marked cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repair 15 mm dia stop cock fancy type, chromium plated with long shank and cup (conncelaed type)for iron pipe or for unions and fixed.

S&F in repair bib taps 15mm bore cast coper alloy with crutch or butterfly handle ISI marked , screwed down, screwed for iron pipe or for union complete all as specified and directed.

S&F pillar taps (fancy type), of 15 mm dia, cast copper alloy ISI marked, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repirs Soap dish, Stainless steel, embedded in the wall approximate size 160x160x90mm complete all as specified and directed.

S&F in repair shower rose 125 mm size brass chromium plated with swivel joints including fixing steel pipe or unions complete all as specified and directed

S&F grating round 140 mm size of PTMT. (Minimum weight 50gms) complete all as specified and directed.

S&F 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F curtain rod 25 mm dia stainless steel chromium plated fixed with brackets complete all as specified and directed.

Dismantling of 100mm bore cast iron drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of 75mm bore cast iron drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

S&F Cast iron soil, waste and vent pipes, sand cast pipe in any length with or without ears with cement joints, laid in trenches or in floors fixed to wall 100mm dia of pipe, complete all as specified and directed.

S&F Cast iron soil, waste and vent pipes, sand cast pipe in any length with or without ears with cement joints, laid in trenches or in floors fixed to wall 75 mm dia of pipe, complete all as specified and directed.

S&F cast iron pipes 110mm bore bends any radius complete all as specified and directed.

S&F cast iron pipes 75mm bore bends any radius complete all as specified and directed.

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F in reapir PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

Excavating in trenches not exc 1.5m wide and not exc 1.50 m depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and getting out in any type of soil

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

Demolition and breaking up drain pipes 150 mm internal dia (SWG, AC or reinforce concrete) set in cement mortar including bedding and hunching complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe complete all as specified and directed.

M&L for 150 mm Reinforced concrte pipes, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L Plain Cement Concrete Type C-2 1:3:6 (using 40 mm graded stone aggrgate) as in foundation filling and mass concrete complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (tubelar pipe, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

S&F framed work as in gusset plate for framed truss, rafters, rails braces etc complete, drilling for fixing of steel sheeting or other covering, door etc to be prepared for hanging or sliding with and including either hook and hinges or steel hanging door fitting etc with welded, riveted or bolted of Fe-410 Gde 250A complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparing newly plastered surfaces on walls, chajjas etc and applying applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 1 to 3mm thick wall care putty complete all as specified and directed.

M&L preparing new plastrered/concrete surfaces of ceiling and applying two coat of distemper oil emulsion (Washable oil bound distemper) on ceiling including cornices, pillasterscomplete all as specified and directed.

M&L for preparation of New surfaces of brick/concrete wall surface and applying applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M & L for preparation of old plastrered or un-plastered surfaces of ceiling & applying one coats of white wash complete all as specified and directed.

M&L for Providing precast cement concrete Type B-0 1:2:4 ( using 12.5 mm graded aggregate) louvres and jallies, 45 mm thick (measured solid), including all mouldings but excluding frame Set in Cement Mortar 1:4 complete all as specified and directed.

Taking down carefully aluminium/copper point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc (for light, fan, socket or power ) complete,including fixture and fitting such as switches,ceiling Roses,pendents,regulators,sockets,light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good the disturbed surfaces of walls, Floors, ceilings etc.

Taking down carefully existing wooden board , Main switch, MCB DB boxes with MCBs, sheet metal boxes, cut out, etc of any size any capacity from boards complete and making good the disturbed surfaces of walls complete all as specified and directed.

Taking down carefully sub main wiring of size including batten and making good disturbed surface of wall complete all as specified and directed.

M & L complete for wiring with cable of size 1.5 sqmm single core copper multistrand conductor including continuous earth wire, using cable FRLS insulated(unsheathed) 1100 volts grade conforming to Is-694 drawn in to and including concealed pvc rigid conduit medium duty with all fittings and fixing accessories ISI certified IS 9537 part -3 and terminated in to pressed steel metal flush boxes suitable for modular accessories and including modular cover plates with frame for mounting switches, socket regulator, brackets etc and including necessary cement work complete all as directed by the Engr in charge including cutting chases pinning in making good to facing and pointing in cement moter 1;3 to the ends or cutting chases for concealed conduit point wiring and making good disturbed surface complete. Cutting not exc 4cm girth and 4cm width for followings:-

All as per Item No 114 here-in-before above but one light point controlled by one, one way switch complete all as specified and directed.

All as per Item No 114 here-in-before above but one fan point controlled by one, one way switch and regulator complete all as specified and directed.

All as per Item No 114 here-in-before above but one 3 pin socket out let 5 amps independent complete all as specified and directed.

(d ) All as per Item No 114 here-in-before above but one 5 pin 5 amps socket point in same board with other switches complete all as specified and directed.

(g) All as per Item No 114 here-in-before above but one 3 pin socket out let 15 amps independent but with cable of size 4.0 sqmm in point wiring and 2.5 sqmm in continuous earth wire complete all as specified and directed.

M & L Modular switch one way 6 amps 1 module complete all as specified and directed.

M & L Modular switch one way 16 amps 1 module complete all as specified and directed.

M & L Modular socket 2 in 1, 5 pin 6 amps 2 module complete all as specified and directed.

M & L Modular socket 2 in 1, 6 pin 6A/16 amp 2 module complete all as specified and directed.

M & L Modular fan regulator stepped type120 watt 2 module complete all as specified and directed.

M & L ceiling rose surface Bakelite 3 terminal complete all as specified and directed.

M& L PVC/ Polycarbonate type Lamp holder, insulated body, with back plate for batten fittings complete all as specified and directed.

S & F energy saving LED lamp 12watt, 230 volts 50Hz complete all as specified and directed.

S & F of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including necessary connections complete all as specified and directed by Engr-in-Charge. Make: Orient/ Havells/ Halonix

S & F of PVC exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed by Engr-in-Charge. Make: Orient/ Havells/ Halonix

S & F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. including elecectric connections complete all as specified and directed by Engr-in-charge.

M & L complete for sub main wiring with single core copper multi strand conductor FRLS flexible insulated (unsheathed) cable of size 2 x 2.5 sq mm and 1 x 1.5 sq mm as in continuous earth wire drawn in to & including pvc conduit medium 25mm dia ISI marked complete with fittings and fixings accessories laid concealed complete. and including necessary cement work complete all as directed by the Engr in charge including cutting chases pinning in making good to facing and pointing in cement moter 1;3 to the ends or cutting chases for concealed conduit sub main wiring and making good disturbed surface complete. Cutting not exc 4cm girth and 4cm width complete all as specified and directed by Engr-in-Charge.

M & L sub main wiring with single core copper multi strand conductor FRLS flexible insulated (unsheathed) cable of size 2 x 4.0 sq mm and 1 x 2.5 sq mm as in continuous earth wire drawn in to & including pvc conduit medium 25mm dia ISI marked complete with fittings and fixings accessories laid concealed complete. and including necessary cement work complete all as directed by the Engr in charge including cutting chases pinning in making good to facing and pointing in cement moter 1;3 to the ends or cutting chases for concealed conduit sub main wiring and making good disturbed surface complete. Cutting not exc 4cm girth and 4cm width complete all as specified and directed by Engr-in-Charge.

M & L sub main wiring with single core copper multi strand conductor FRLS flexible insulated (unsheathed) cable of size 2 x 6.0 sq mm and 1 x 4.0 sq mm as in continuous earth wire drawn in to & including pvc conduit medium 25mm dia ISI marked complete with fittings and fixings accessories laid concealed complete. and including necessary cement work complete all as directed by the Engr in charge including cutting chases pinning in making good to facing and pointing in cement moter 1;3 to the ends or cutting chases for concealed conduit sub main wiring and making good disturbed surface complete. Cutting not exc 4cm girth and 4cm width complete all as specified and directed by Engr-in-Charge.

M & L 1x 20 watts ( 4 feet) wall mounted LED batten,extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver including lamp complete all as specified and directed by Engr-in-Charge.

M & L 1x 9/10 watts ( 2 feet) wall mounted LED batten,extruded aluminium heat sink provided for efficient heat dissipation &integrated electronic driver including lamp all as specified and directed by Engr-in-Charge.

M & L MCB DB, sheet steel, phosphatised, powder printed with bus bar, neutral link, earth bar & din rail SPN dist board 08 ways double door complete all as specified and directed.

M & L MCB single pole & neutral 240 volts, C curve-10 kA 40 to 60 Amp complete all as specified and directed.

M & L MCB single pole 240 volts,C curve-10 kA 10 Amp complete all as specified and directed.

M & L MCB single pole 240 volts ,C curve-10 kA 25 Amp complete all as specified and directed.

M & L MCB single pole 240 volts ,C curve-10 kA 32 Amp complete all as specified and directed.

M & L earthling with galvanized iron earth plate electrode 600x600x6mm thick buried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5mtr (B.G.L.) and connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washer of galvanized iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made of 12mm round bar, including necessary excavation &earth work in any type of soil, 20mm dia medium grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 40 mm dia bore, light grade galvanized steel tubing up to 7.5 mtr length for drawing earth lead wire protection common salt, charcoal etc complete all as shown in EP No 3 of SSR Part 1 and testing on completion complete all as specified and directed by Engr-in-charge.

Supply and laying or fixing or passing in replacement through pipe cable XLPE (FRLS) with aluminium conductor with heavy duty stranded 1100 volts size of 10 Sqmm 2 Core complete all as specified and directed. Note:- XLPE insulated PVC sheathing (heavy duty) armoured cable with aluminium conductor for working pressure up to and including 1100 volts to IS-7098 (Part-I) for PVC insulated cables with following features (a) Cable shall have fire retarded low smoke (FRLS) compound added to it in the out sheathing as per IEC 754(part-I) IEC-60332 part-2 IFEE 383 ASTM 2x43 and ASTM 2X63 flame retardant compound (PR) as per EIC specification. (b) Inner sheathing shall be of extruded PVC. (c) Heat resisting PVC shall also be added to extrude inner and outer sheathing (d) Cable shall also be supplied with sequences hall marking at every meter as the outer sheathing. (e) Ultra violet radiation resistances compounded comprising ton ASTMG-53. (f) Anti rodent and ant termite compound added. (g) PVC compounds of various grades as IS-5831. (h) compaction conductors shall be shaped and arrangement for the same with be on the cable. Note:- (i) Each cable shall be tested for all applicable routine tests as per IS-5831,IS-7098 BS-6746,BS-5467 and IEC 60502 and test reports shall be provided to GE. (ii) Type test as per relevant specification shall produce to GE.

All as per item No. 137 here-in-above but size 35 Sqmm, 4 Core complete all as specified and directed.

Supply and laying well burnt sub class ‘B’ bricks, locally available of size 23x11.5x7.5 CM (+_8% tolerance) in trenches for protection of underground cable complete all as specified and directed by Engr-in-Charge.

M & L drilling hole under hard standing /road for laying of pipe for protection of cable etc by means of mannual buckle and without disturbing the top surface and making good the disturbed surface if any complete all as specified and directed by Engr-in-Charge.

Supply and laying in replacement of GI tube light grade 50 mm bore ISI marked complete all as specified and directed.

Schedule of Credit

MOHIT ENTERPRISES (BID ID -3121819)

M/s R P Enterprises (BID ID -3121385)

PUNEET CONSTRUCTIONS CO. (BID ID -3121686)

M/s Vijay Enterprises (BID ID -3130240)