PROVN OF DIFFERENTLY ABLED FRIENDLY FITTINGS ALL TOILETS AND BATHROOMS, INSTALLATION OF SAFETY GRILL GUARD BALCONIES AND GRILL GATE AT INHS DHANVANTARI, PROVN OF SENTRY POST AT NORTH GATE OF INHS DHANVANTARI AND PROVN OF NEW NAME BOARD AND ASSOCIATED

Amount

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement of complete all as specified and as directed by engineer-in-charge.

S& F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walkways; railings; framework of water tanks/water staging and similar work conforming to Fe.410 W (Gde E 250 Quality B) of complete all as specified and as directed by engineer-in-charge.

S&F Grab bar of Dia 32 mm with snap flange made of AISI 304 stainless steel for horizantal and vertical slanting installation suitable for specific bathrooms for people with mobility problems,elderly people or handicapped where ever neccesary as per requirement including all necessary drilling, bolting or riveting etc, of complete all as specified and as directed by Engineer-in-Charge. Make: Jaquar or equivalent

S&F safety vertical swing grab bar consists of U shaped tube,with a built-in toilet paper holder made of 32 mm Dia AISI 304 Stainless steel tube and a heavy duty wall plate,3 mm thick provide rigid support where it is needed-on one or both sides of toilet along with safety swing up position that locks bar in vertical position,required to increase acccesibility and safety of people with disabilites or mobility difficulties where ever neccesary as per requirement including all necessary drilling, bolting or riveting etc of complete all as specified and as directed by engineer-in-charge. Make: Jaquar or equivalent

S&F Disabled folding shower seat of size 460 x 370mm made of AISI 304 stainless steel and PVC Coated movable in horizantal and vertical direction slanting installation suitable for specific bathrooms for people with mobility problems,elderly people or handicapped where ever neccesary as per requirement including all necessary drilling, bolting or riveting etc, of complete all as specified and as directed by Engineer-in-Charge. Make: Jaquar or Equivalent

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

M&L for Plain Cement concrete type C2 1:3:6 (using 40 mm graded stone aggregate) in foundations,filling and mass concrete complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point Complete all as specified.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams, and similar work for rough finished flat surfaces complete all as specified and as directed.

M&L RCC M30 grade (Design Mix) using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams; bases for coloumns, etc basement slabs, under-reamed piles and mass concrete complete.

M&L for TMT bars 10mm dia and over cut to length, bent to shape required incl cranking, bending, spirally for hooping for columns, hooking end and binding with and incl mild steel wire not less than 0.9mm dia or securing with clip quality confirming to TMT bars complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions all as specified and directed.

M&L RCC M30 grade (Design Mix) using 20mm graded stone aggregate as in columns, pillars, piers, post and struts etc of complete all as specified and as directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and directed.

M&L RCC M30 grade (Design Mix) using 20mm graded stone aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L Roof trusses (framed), trusssed, purlings, crane gantries, rails and fasternings and heavy breacket frasming (Beam, tee, angle, Channel, hollow sec or flat sections) including distance pieces, cleates, gusset paltes etc Fe 410-w grade E-250 quality A of complete all as specified and as directed.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410 W (Grade E-250) quality A of complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as manufacturers instruction and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing all as specified and as directed.

S&F aluminium flat 40 X 6mm size as wind tie fixed with 50mm/75mm aluminium self staging screws of complete all as specified and as directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided of complete all as specified and as directed.

M&L precast cement concrete block masonry with solid block, exc 10cm in width in PCC type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) all as specified.

M & L for rendering 15 mm thick in cement mortar 1:4 over concrete or brick masonry surfaces and finishing the top surface even and fair without using extra cement complete all as specified and as directed.

M & L for rendering to concrete or block masonry surfaces or surfaces other than fair faces of brick surfaces, 10mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L rendering 5mm thick in CM (1:3) on ceiling surfaces finished even & smooth without using extra cement of complete all as specified and as directed.

M&L preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer and 2mm thick wall care putty all as specified.( Wall care putty can be measured and paid separately)

M&L for preparation of newly plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of primer all as specified.

M & L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-charge. Make: Asian Paints (Apex Ultima), Berger (Weathercoat Long Life Flexo) Nerolac (Excel Total), Shalimar Paints (Weatherpro+ Super Luxury Emulsion)

M & L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of WHITE colour with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-charge. Make: Asian Paints (Apex Ultima), Berger (Weathercoat Long Life Flexo) Nerolac (Excel Total), Shalimar Paints (Weatherpro+ Super Luxury Emulsion)

S& F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.410 W (Gde E 250 Quality B) of complete all as specified and as directed.

S & F Mild steel screw bolts (machine made) 5 to 10 mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n.exc. 10 cm long.

M&L for Powder Coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators and partition with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium powder coating of any colour (Thickness or powder coating not less than 50 micron) door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S & F Anodised aluminium powder coating of any colour (Thickness or powder coating not less than 50 micron).window and ventilator shutters (sliding type), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S & F only 4 mm Plain sheet glass ordinary quality, in square not exc 0.5 sqm each complete all as specified and as directed by Engr-in-charge.

S & F only 4 mm Plain sheet glass ordinary quality, in square exc 0.5 sqm each complete all as specified and as directed by Engr-in-charge.

S&F in 12mm thick Prelaminated particle board, interior grade, prelaminated on both sides with decorative choice lamination fixed as in panels of Aluminium door shutters, partition etc complete of complete all as specified and as directed.

S & F only Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including taking down all as specified.

S & F 100mm length Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-11 including srews

S&F extruded aluminium alloy handle fabricated type anodised 100mm long of complete all as specified and as directed.

S&F Aluminium anodised sliding door bolts 250 mm long with hasp and staple of complete all as specified and as directed.

S&F aluminium anodised barrel tower bolt of extruded section 150mm long of complete all as specified and as directed.

S&F Aluminium (extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between61 to 80 kg and fixed complete all as specified and as directed.

S & F Floor Door Stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

M&L for preparation of new steel surfaces over 10cm width or grith and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-1 (40 mm graded aggregate) as in floor all as specified and directed, finishing cement concrete surface evan and smooth with using extra cement of complete all as specified and as directed.

M&L for glazed ceramic tiles 450x300x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing in cement mortar (1:3) all as specified and directed.

M&L for 18-20mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 20 mm thick screed bed in CM 1:6 of complete all as specified and as directed.

M & L for 25 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in sub base for flooring/levelling coarse etc complete all as specified and as directed.

M & L for Heavy duty Parking Tiles 40cm x 40cm x 10 mm thick, set, jointed and pointed in near cement slurry in floors With grey cement and pigments and including screed bed 15mm thick CM 1:4 of complete all as specified and as directed.

M&L for moorum/ red bajri /garden soil suitable for plantation filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering of complete all as specified and as directed

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per sq. metre etc.complete all as specified and as directed

S& F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Providing edge moulding to M & L for 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed by Engr-in-Charge.

Preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer of complete all as specified and as directed

S & F sign board of size (800x1200mm) with one side cut framed with 50mm dia SS tube and assembled with two pole structure of 70 mm dia SS pipe with one side height 1400mm and other side 1700 mm from GL as mentioned in Drg with double sides made out of 4mm thick aluminium composite panel sheet covered retro reflective H1 prismatic sheeting including letter/sign and a logo to be fixed after etching treatment to sheet and fixed on support frame of stainless steel frame complete including embedding in PCC of size (0.30x0.30x0.60), 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate) and necessary earthwork in any type of soil complete all as shown on drg as specified and directed bv GE

Providing and fixing of Machine cut Polycarbonate Sheet translucent sheet letters bacl lit using required LED and drivers in English with letter of name of institute of minimize size 300 mm with 25 mm raising with content "HQ COMMANDER WORKS ENGINEERS", in 200 mm with 25 mm raising "SRI VIJAYA PURAM", "Military Engineer Services" and atleast 2 logos of sixe not les than 450 mm diameter. The letters of name of institute in logo shall be engraved/etched in letters complete all as shown as drg. The entire letters shall be fixed on ACP Sheet board of size not less than 8 m X 4 m along with user approved border framing in ACP sheet. The Aluminium and MS work required for the same shall be considered included in this rates quoted by the contractor. The work shall be executed to the satisfaction of Engineer- in-charge and on the existing wall as per directions complete.

M&L for point wiring with two run of PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm (FRLSH), PVC conduit medium grade/PVC casing caping and pressed steel terminal boxes (for mounting modular switches /modular sockets/ modular regulators etc) complete and drawing one run of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor cable (FRLSH) as earth continuity wire in green colour connected to common earth and each terminal box/fitting all as specified and as directed Note: The quoted rate inclusive for the following :- (a) GI metal flush box and Modular cover plate with frame of any module complete. (b) Proper colour coding is to be followed as per IS Specification. (c) wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement.(d) Cutting chases/making good disturbed surfaces of wall for fixing concealed conduit wherever required will be masured and paid separately.

One light point controlled by one switch.

One ceiling fan fan point controlled by one switch.

One 3 pin socket outlet 5 Amps on the same board with other switches

One 3 pin socket outlet 5 Amps independent.

S&F modular switch one way 6 Amps, 1 module complete all as specified and as directed

S&F modular socket, 2/3 pin 6 amps, 2 module complete all as specified and as directed.

Supply & fixing ceiling Rose, 3 terminal polycarbonate isolated body complete all as specified and as directed.

S&F LED lights fitting 20W, >120lm/watt, CCT value 4000K to 6500K, surge protection of 2 KV, 4 feet 220V, AC IP-20, aluminium housing with inbuilt driver including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Supply and fixing as in repair LED inverter bulb 12 Watt, CDL, 220V AC complete all as specified and as directed.

Supply & fixing BLDC ceiling fan 1200mm sweep with blades, suitable electronic remote as per OEM design, down rods and connected accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM, 5 star rated, equipped with brushless direct current motor (BLDC) of wattage < 28W including provision of cable from ceiling rose/connector to fan complete all as specified and as directed.

Supply & fixing MCB DB's SPN 4 way, IP-54, IK-09 double door, sheet metal enclosure, 240V, suitable rated busbar as per OEM design including suitable size of copper ferrules for fixing of cable complete all as specified and as directed. Note : (i) MCCB and MCB will be measured and paid separately. (ii) The cost for flushing of Distribution box in any type of wall and making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate

Supply and fixing MCB SPN 32 Amps ,10 KA, C Curve, 230 Volts ,50 HZ complete all as specified and as directed.

Supply and fixing MCB SP 6-32 Amps ,10 KA, C Curve, 230 Volts ,50 HZ complete all as specified and as directed.

Supply and fixing PVC insulated, sheathed two core aluminium conductor 10 sqmm drawn through suitable size of PVC conduit complete all as specified and as directed.

M&L for concealed submain wiring with PVC insulated unsheathed multi-stranded copper conductor cable two run of 2.5 Sqmm single core (FRLS) 1100 volts grade drawn through in and including non metallic rigid PVC conduit, medium duty not less than 25 mm dia concealed in wall/fixed on wall/ceiling with GI saddles, GI screws, rawl plugs with all fittings and one run of 2.5 Sqmm PVC insulated copper conductor(FRLSH) for earth continuity wire complete all as specified and as directed. Note: Two run of single core cable with one run of earth continuity conductor and PVC conduit and its fittings will be measured as one length. ii) Rates are deemed to be included for chases of conduit, cutting and making holes in wall/floor for passing in or through conduit and making good disturbed surfaces with existing wall colour complete.

Supply & fixing LED flood light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame, (with total lumen output not less than 6000 lumens and suitable wattage for efficiency not less than 120 lumens/Watt) min wattage 50 watt, with ingress protection IP 65/66 and SPD of capacity 10 KV etc inci necessary clamps etc complete and testing on completion all as specified and as directed. Make:Crompton /Phillips/C&S /Havells/ Wipro/ Henolix/Luker .

Supply & fixing LED Rope light of length not less than 50mtr and having 120 LEDs per mtr with total lumen output not less than 22500 lumens and suitable wattage for efficiency not less than 450 lumens per mtr min wattage 450 watt, with ingress protection IP 65/66 and SPD of capacity 10 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed. Make:Crompton /Phillips/C&S /Havells/ Wipro/ Henolix/Luker .

RS ENGINEERING WORK (BID ID -3316515)

Sri Ram Construction (BID ID -3316021)

ABR Construction (BID ID -3315978)

CHANDER SEKER ENTERPRISE (BID ID -3315916)

ANITA VARMA ENTERPRISES (BID ID -3316194)

MAJUMDAR FURNITURE (BID ID -3316235)

M/s Saina Enterprises (BID ID -3316137)