SPECIAL REPAIR TO BLDG NO 95/4 (04 QTRS) OR MD ACCN AT SUBATHU UNDER GE KASAULI

Schedule 'A' Section - I

Demolition of cement concrete (un re-inforced) in ground floor and paving n.exc. 15 cm thick below or above ground level complete all as specified .

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition)

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Dismantling PVC 75/110 mm drain or vent pipe of any description in any position including bends branch pieces etc.

Taking down cement plaster on brick wall surfaces etc incl raking out joints hacking for key, scrubing down with water etc cpmplete all as specified and as directed

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as spd and as directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) n.exc. 1.5 Sqm complete all as spd and as directed.

Taking down chowkats or frames with shutters (without taking off shutters) exceeding 1.5sq.m and not exc 4.00sq.m each of any description incl making good the disturbed surfaces complete all as specified & directed.

Dismantling plain or corrugated steel sheeting any guage thickness incl Nainital pattern as in roof covering complete all as specified.

Material & Labour brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified & directed.

Material & labour for 15mm thick rendering in cement mortar 1:4 over fair faces of brick masonry surfaces or concrete surfaces finished even and smooth without using extra cement complete all as specified.

Material & Labour rendeing 10mm thick other then fair faces surfaces in CM 1:6 finished even and smooth with out using extra cement (Internal surfaces)

Material & Labour rendering 5mm thick in CM (1:3) on fair faces of concrete surfaces as in ceilling finished fair and even without using extra cement complete all as specified and as directed

Material & Labour for for applying 3 mm thick wall care putty (applied in two layers) of old /new decorated plastered or unplastered surfaces of wall complete all as specified and directed

Material & Labour for Plain Cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in seismic and other similar bands, shelves, copings, bed plates, hold fasts, plinth courses, filling in pressed steel frame and the like finished fair and even incl necessary form work complete all as specified & directed.

Material & Labour for 50mm thick plain cement concrete C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection finished fair and even without using extra cement complete all as spd & directed. Note:- The plinth protection shall be laid in pannels and length of the each panel shall not be more than 2.00 mtr all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment against the above item.

Material & Labour RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in shelves / slabs and like with and incl use and waste of necessary form work complete all as specified.

PCC (1:3:6) type C2 using 40mm graded agg as in surface channel / drains.

Extra for forming fair finished drain or channel 30 cm inner girth in forms, moulds/stopped ends etc.

Material & Labour MS TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges etc. fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape (Jhhallar) as directed at site fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

Material & Labour Non Skid ceramic tiles 7 to 8 mm thick area exc 0.18sqm n exec 0.38 sqm in floors, set and jointed in neat cement slurry and pointed in white or colored cement to match with the tiles incl. 15mm thick screed bed or bedding layer in C.M 1:4 etc complete all as specified & as directed

Ditto but skirting over 10 mm thick rendring in CM 1:4

Material & Labour for coloured glazed ceramic tiles in vertical surface 350 x 250 x 7mm / 450 x 350 x 7mm /450X300X7 mm thick set & jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed in 1:6 cement mortar complete all as specified & as directed

Pressed steel frames for doors of size 105 x 60mm thickness 1.25 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, as specified, supplied and fixed

Pressed steel frames for doors of size 125 x 60mm thickness 1.25mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, as specified, supplied and fixed.

Supply and fixing factory made steel windows with side hung shutters including projecting type hinges with steel handle , and steel peg stay , complete with glazing bars , dovetailed or welded complete all as specified & diretced

Supply and fixing steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Supply and fixing framed work such as grills, gratings, etc with ends of bars shouldered and / or riveted, or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings , framework of water tanks and similar work conforming to Fe 290 Gde E-165

Supply and fixing galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specifeid

Supply and fixing sheet glass , ordinary quality & glazing 3mm thick, with oil putty in square n. Exc 0.5 Sqm in each pane complete all as specified & as diretced

Supply and fixing figured glass 4mm thick, pin head type and glazing with oil putty in square n. Exc 0.5 Sqm in each pane complete all as specified & as diretced

Supply and fixing Factory made plain, framed, panelled shutters , 35mm thick of 2nd class hard wood (Hollock) with lock rail and panels of 9mm thick commercial ply or 12mm thick vaneered particle board with commercial veneered on both sides, incl priming coat, duly hammer marked. The size of rail & style shall be as per IS 1003 part-1 kiln seasoned and chemically pressure treated incl one coat of pink primer complete all as specified & directed.

Material & Labour 30mm thick 2nd class hard wood glazed and skeleton shutter factory made open revated and prepared to receive glass, guage etc with plain chamfered or rounder mitred and rebated, sash bars in any numers divided into squares edges of framing, plain or chamfered or rounded as specified in SSR Pt-I, section 8, clause 8.24(a) supplied and fitted to chowkats complete all as directed.

Supply and fixing factory made solid PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reinforced with mS square tube etc complete all specified.

Supply and fixing factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2.4 (or) 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethen painted on the front face and 2mm plain colur PVC sheet on back face with particle board core etc complete all specified & as directed .

Supply and fixing in repairs curtain rails anodised aluminium alloy with fixing brackets etc complete all as specified

Supply and fixing Mild steel butt hinges medium weight , clod rolled, 100mm, ISI marked, complete all as specified & directed.

Material & Labour barrel tower bolts aluminium anodised extruded section of size 200 mm complete all as specified & directed.

Material & Labour barrel tower bolts aluminium anodised extruded section of size 150 mm complete all as specified & directed.

Supply and fixing aluminium fabricated type extruded handles of size 125 mm complete all as specified & directed.

Supply and fixing 300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as specified & directed.

Material & Labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl washing, rubbing down and stoping the connected previously treated surfaces and applying two coats of oil emulsion distemper (tint as approved by GE) complete all as specified & directed.

Material & Labour for preparation of plastered or unplastered new surfaces of walls and applying two coat of oil emulsion distemper (tint as approved by GE) including one coat of primer complete all as specified.

Material & Labour preparation of newly plastered or unplastered or previously untreated surfaces of walls and applying two coats of exterior emulsion/Apex paint complete all as specified.

Material & labour for preparation of old painted wood or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) complete all as specified & directed.

Material & labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint (1st quality) over a coat of red-oxide primer complete all as specified & directed.

Taking up or down 15 mm dia steel tubing and connection and removal from site

- Ditto- but 20mm dia

Supply and fixing steel water tubing medium grade galvanized with all fittings and fixed complete to walls andceiling or laid into floor or 15mm bore complete all as spd.

-ditto- but bore of pipe 20mm . Note:- (shefting/Re-fixing of water meter is also included in the rate)

Supply and fixing in repairs 15mm bib tap cast copper aloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified.

Supply & fixing wash hand basin, vitreous china, white, decorative type, flat or angle back, size 550mm x 400mm incliding cutting for and pinning in ends of brackets or erecting stand including waste pipe , fixed as in repairs complete all as specified.

Supply and fixing in repair 15mm pillar tap cast copper aloy with capston heads chromium plated screwed down fly nuts screwed for iron pipe or for brass ferrule and fixed complete all as specified.

Supply and fixing in repairs brass chromium plated tubler towel rail 20mm dia D type 60cm long between flanges complete all as spd.

Supply and fixing in repair grating doom 100 mm dia of PTMT (Min wt 25g) all as specified and as directed

Dismantling water tanks n.exc 500 ltrs cap and removing to store complete all as spd.

Supply and fixing 500 ltr cap ratational moulded polythene water stoarage tanks ( clyndrical vertical with closed top) hoisted and fixed in position complete all as spd.

Supply and fixing in repair 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified

Supply and fixing in repairs of flushing cistern PVC 10 ltrs cap valve less syphonic action type, low level white with intel , ball valve , float incl brackets and PVC flush pipe 32mm dia complete all as specified. .

Supply and fixing angle stop valve, chromium plated, brass fancy type, screwed down, high pressure with crutch or butterfly handle screwed down , screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

Supply and fixing 15mm dia PVC connection with brass nut, of length 450mm, in repair complete all as specified and directed.

Supply and fixing in repairs vitreous china squatting pan, "Orissa Pattern" size 580 x 440mm white with integral foot rest (excluding flushing cistern) and flush pipe complete all as specified

Supply and fixing in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch of butterfly handle scewed both ends for iton pipe or for unioin fixed complete all as specified

Supply and fixing 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

Supply and fixing 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

Supply and fixing 75mm dia PVC (SWR) bends with oval accesse door with rubber ring joints fixed as required complete all as specified.

Supply and fixing 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified.

Supply and fixing 75mm dia PVC (SWR) junction single, (single T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

Supply and fixing 110mm dia PVC (SWR) junction single, (single T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

Supply and fixing 110mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

Supply and fixing 75mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

Supply and fixing 110mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

Supply and fixing 75mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

Material & Labour for Granite as in steps, pillars, window cills, cooking plateforms and like, 20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick cement screed bed in CM(1:6) complete all as specified. ( size of the slabs shalll not be less than 100cmx60cm ). Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish all as spfd.

Supply and fixing in repair soap dish chromium plated of size 180x160x90mm any type, fixed with chromium plated brass screws complete all as specified.

Material and labour for sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and wastes, overall size 915mm x 460mm, bowl size 410mm x 330mm x160mm incl fixing cantilever brackets and connection to union, pipe, fixed as in repairs complete all as specified and directed.

Supply & fixing stainless steel plate rack, made out of 1.00mm thick sheet of size 24"x36"x10" deep, ISI marked, fixed as in repairs complete all as specified and directed.

Supply & fixing pre-laminated particle board 19mm thick, interior grade pre laminated one side with decorative choice laminations and other side balancing white lamination, fixed with screws to timber / steel frame work as in shelves or shutters or wall panelling, fixed as in repairs complete all as specified and directed.

Material & labour piano hings, mild steel bright finish width of flap 40mm fixed in repair including taking out the existing complete all as specified and directed

Supply & fixing magnetic catches brass body for use in cup boards of kitchen, ward robes etc. fixed as in repairs complete all as specified and directed.

Supply & fixing 40mm dia cupboard knob of brass, polished, fixed with nut screw and washer, fixed as in repairs complete all as specified and directed.

Supply and fixing in repair chromium plated shower rose (125mm) with swivel joints fixed to steel pipe or union complete all as specified and directed.

Hasp and staple 75mm, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws

Material and labour for water proofing treatment of sunken floor of WCs, bathroom etc. by applying of the following specifications :- (i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc. and remove all loose/unsound material, dirt, dust, etc. (ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydroproof Xtra of FOSROC/Equivalent of Dr Fixit of Pidilite Industries Ltd in the ratio of 1:2:4 (One part of acrylic polymer : Two part of water and four part of cement). (iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.222 Litre/Sqm and allow it to air dry for 04 hours. (iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.111 Litre/Sqm and allow it to air dry for 04 hours followed with water curing for 48 hours. (v) 200 micron thick polythene film shall be pasted with help of adhesives over treatment. Note :- Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work.

Material and labour for plain cement concrete 1:5:10 type E-2 (using 40mm graded broken bricks aggregate) as in foundation, filling and mass concrete, complete all as specified and as directed.

Material and labour for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling courses laid and compacted in slope in floor complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition and breaking up drain pipes 150 mm dia (Salt glazed ware,AC or Reinforced concrete) set in cement morter

Demolition and breaking up drain pipes 200 mm dia (Salt glazed ware,AC or Reinforced concrete) set in cement morter

Material and labour for 150mm bore sail -glazed stoneware drain pipess laid in trenches and jointed as specified and directed by Engr-in- Charge.

Material and labour for 200mm bore sail -glazed stoneware drain pipess laid in trenches and jointed as specified and directed by Engr-in- Charge.

Material & Labour for concrete bed to drain pipes 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C2 using 40mm graded stone aggregate including demolition of damaged concrete complete all as specified and as directed by Engr- in-Charge.

Material & Labour for concrete bed to drain pipes 200mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C2 using 40mm graded stone aggregate including demolition of damaged concrete complete all as specified and as directed by Engr- in-Charge.

Material & Labour for PCC 1:4:8 type D-2 Using 40 mm graded stone aggregate as in foundations , filling and mass concret complete all as specified.

Demolition of brickwork built in cement or cement lime mortar complete all as specified and as directed by Engr- in-Charge.

Material & Labour Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement Mortar 1:4 as in manholes complete all as specified and as directed by Engr- in-Charge.

Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces of wall in cement mortar 1:4 for finished even and smooth (without using extra cement) complete all as specified and as directed by Engr- in-Charge.

Material & Labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms mould stopped ends complete all as specified and as directed by Engr- in-Charge.

Material & Labour for cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in surface channels, drains and coping including form work complete all as specified and as directed by Engr- in-Charge.

Material & Labour for cutting into exising manholes for connecting new drains, making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, smooth finished & reforming benching as required for internal dia of pipe 150mm. complete all as specified and as directed by Engr- in-Charge.

Material and labour for Precast cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in cover slabs of manholes, gully traps etc set in cement mortar (1:4) complete all as specified and directed.

Supply and fixing in repair false ceiling with fully perforated 12mm thick micro tegular edged or 10mm thick square edged GRG false ceiling tiles at all height with GRG (Glass fibre reinforced gypsum) false ceiling tiles with fully perforated 12mm thick micro tegular edged or 10mm thick square edged GRG false ceiling tile 595mmx595mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4) - 1970 and light reflctance of 85% minimum to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @120grams per Sqm incl both sides) comprising of main T-runners of size 15x32mm of length 1200mm, and secondry intermediate cross T- of size 15x32mm of length 600mm to from grid moudle of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanizing @80 grams per sqm) ie 50mm long, 8mm outer diameter M*6 dash fasteners, 6mm dia fully threated hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws complete all as specified and directed.

Material & Labour for Surface excavation in soft losse soil n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specidfied and directed by Engr-in- charge.

Material & Labour for Hard core, broken to gauge n exc 63 mmcomplete all as specidfied and directed by Engr-in- charge.

Material & Labour for providing cements 1:3:6 type C1 using 20mm graded aggregate as in plinth course,string courses, lacing courses, parapets and rainling up to 60 cm height, copings, kneelers, apex stones, bed plates, water troughts and the like including weathering,slightly rounded or champfered angles and throating incl use and waste of necessary form work complete all as spd. complete all as specidfied and directed by Engr-in- charge.

Material and labour, coloured chequered cement concrete tiles 200X200X25mm or 300x300x25mm thick, factory made, ISI marked (IS 13801-1993), with grey cement & pigment, laid with neat cement slurry as in path, pavement ,floors, etc. @ 3Kg/Sqm over & including 20mm thick screed bed of cement mortar (1:6), pointed in white cement with matching colour pigment, complete all as specified and directed.

Material & Labour for Providing, cement concrete type B1 1:2:4 (20 mm graded aggregate) in drain both side kerbs or mud stops, rounded or chamfered on edges complete all as specified

Taking down copper/ aluminium point wiring(light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc complete.

Material & Labour for point wiring with PVC insulated and unsheathed cable single core multistranded FRLSH copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including medium grade PVC rigid non metalic conduit concealed in any type wall should be (cutting wall using electric driven cutter) conforming to IS-9537 with all accessories including modular cover plate, base plate and MS metal box of thickness 1.2mm as per site, 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-

One light/fan/Ext Fan point controlled by one switch

One Bell point controlled by one switch

One light point controlled by 2 way switch

One switch socket outlet 3 pin,5 Amp on the independent board

One switch socket outlet 3 pin,5 Amp on same board

All as per item No. 115.00 above but with 2.5 sqmm (Nominal cross sectional area) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15/16 A socket outlet on independent board complete all as specified and directed.

All as per item No. 115.00 above but with 4 sqmm (Nominal cross sectional area) cable with 4 Sqmm size copper earth continuity conductor for 3 pin 15/16 A socket outlet on independent board complete all as specified and directed.

Supply and fix modular switch, 6 Amp, one way complete

Supply and fix modular switch, 16 Amp, one way complete

Supply and fix modular switch, 6 Amp, two way complete

Supply and fix modular bell push, 6 Amp, one way complete

Supply and fix modular socket 6 Amp 2/3 pin combined 2 module complete

Supply and fix modular socket 6/16 Amp 2/3 pin combined 2 module complete

Supply and fix modular Fan step regulator suitable for BLDC fan, 120W-2 module complete

Supply and fix in repair Door bell electronic, music type, 230 volt AC.

Supply and fix ceiling rose, 3 phase/ PVC/ polycorbonate complete

Supply and fixing 25 A DBOXx SRCD is ready plug & play all-in-one device that provides protection to humans from electric shock due to direct or indirect contact as well as provides protection from overload and short circuit faults. It is designed such that user can easily upgrade his installation by replacing existing socket boxes and get built-in protectioin.

Supply and fixing lamp holder, PVC insulated body, with back plate suitable for batten fitting complete all as specidfied and directed by Engr-in- charge.

Supply and fixing Decorative wall light fixture made up of Polycarbonate, suitable for 10 W retrofit LED lamp B22 base complete all as specified and directed.

Supply and fixing in repair LED bulb 10 watt complete all as specidfied and directed by Engr-in- charge.

Supply and fixing in replacement 20 W Inverter LED batten with square profile & polycarbonate channel Lithium Ion battery with charging time 8 hours-10 hours and back up time upto 4 hours.

Supply and fixing 10 Watt wall mounted LED batten with polycarbonate housing & integrated electronic driver complete with all fixing accessories and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

Supply and fixing Bulkhead luminaire Decorative Energy saving new generation 10W LED IP65 with opal diffuser incl electronics driver & connection with copper flexible cable 3 core complete all as specified and directed.

Supply and fix in repair 25 watt LED Light New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08 with all accessories internally pre-wired and suitable size bracket including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Supply and fixing SPN DB 8 Way, 240 Volt, sheet metal enclosure with double door for DBs confirms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector complete all as specified and directed

Supply and fix MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

Supply and fix MCB single pole & neutral 40 Amps 240 volts, C series,10 kA rupturing capacity

Material & Labour for submain wiring with 2 single core PVC insulated FRLS cable 4 Sqmm copper conductor PVC sheathed in and including rigid medium grade PVC concealed conduit heavy duty of suitable size incl cutting chiseling of wall and making good to disturbed surface of walls / floor etc with plastering painting etc so as to match with the existing finishes, drawn with 4 Sqmm PVC insulated FRLS copper conductor cable for earth wire fixed with shaddle and connecting to common earth teriminals complete all as specified.

Taking down exhaust fan dismantling and painting of exhaust fan complete at site with synthetic enamel paint by spraying incl (fittings with filler) one coat after cleaning all dust etc incl connecting up. Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire incl replacement of capacitor, bearing/bush, rubber bushes minor nuts bolts screws washers greassing in fan bearing & refix same complete all as directed

Rewinding of 300mm sweep Exhaust fan with appropriate size of copper enamelled wire including varnishing ,heating with proper insulation complete and testing all as specified and directed.

Taking down ceiling fan and and replacement of fan controllaer as per existing model and make and cleaning all dust etc incl connecting up. Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire incl bearing/bush, minor nuts bolts screws washers & refix same complete all as directed

Taking down geyser from site and cleaning, paiting and minor repair (i.e. replacement of indicator lamp, non return valve (Brass), element and tharmostate) complete provn of twin core cable of suitable size 3 core from geyser to powerpoint with plug top 15A and refixing at site after complete repair of building.

Taking down and Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches on poles through pipes, fixed to walls etc cross sectional area 25 Sqmm 3.5 core complete all as specified and directed.

Earthing complete with and including galvanised steel earth plate electrode 60 cmx 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers, buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top as of the plate at a depth of not less than 1.5 mtrs below normal ground level connected to galvanized iron or steel earth lead wire 4.0 mm dia,( NO 8 SWG) by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 15 mm bore (light grade) and connected to main switch or main control board all as shown in electrical plate No. 3 of SSR - 2009(Pt I) & including necessary excavation and earth work. The rate also include charcoal and salt in alternate layers, 20 mm bore GI pipe (Light grade ) for watering , protection pipe funnel, wire mesh , PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Normal mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : The unit rate include earthing lead and protection pipe upto 7.5 metre from top of earth plate.

Amount of credit of Rs. 67344.00 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

Please Enable Macros to View BoQ information