RECALL - Annual Repair of various quarters in PWD Colony Gurugram for the year 2022-23. (i) SDE Residence House no. 4and5 (ii) SDE Residence House No. 6and7 (iii) EE Residence H.No. 3A (iv) E.E. Residence H.No. 3 (v) 770 sft Quarter (Subji Mandi)

Amount

10 mm thick cement plaster 1 :3 (1 cement: 3 fine sand)[New HSR 11.4.2]

12 mm cement plaster of mix (4). 1 : 6 (1 cement: 6 fine sand) [New HSR 11.5.4]

15 mm cement plaster on the rough side of single or half brick wall of mix 1 :4 (1 cement: 4 fine sand)(New HSR 11.6.1)

Cement pointing 1 :2 on lining On side slopes(HSR 14.23.2)

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete. [New HSR 11.58]

Distempering with 1st quality acrylic distemper (ready made) having VOC content less than 50 gm per litre. of approved manufacturer and of required shade and colour complete. as per manufacture r's specification. (1). One or more coats on old work. [New HSR 30.34.1]

Distempering with 1st quality acrylic distemper (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade. Old work (one or more coats). [New HSR 30.25.1]

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade.(1). One or more coats on old work [New HSR 30.28.1]

Finishing walls with Acrylic Smooth exterior paint of required shade. (2). Old work (Old work (Two or more coat applied @ 1.67 litre/ 10sqm) on existing cement paint surface).[New HSR 30.37.1]

Providing and laying of conglomerate floor 40mm thick cement concrete topping 1 :2:4(HSR 10.8)

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws(HSR 12.37.1)

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete With 2nd class teak wood beading 62X19 mm(HSR 12.53.1)

Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : (1) 4.0 mm thick glass panes. [New HSR 13.10.1]

Providing and laying of precast terrazzo tiles 20 to 22 mm thick with gradedmarble chips of size up to 12 mm, laid in floors, and landings, jointed with neat cement sluny mixed with pigment to match the shade of the tiles,including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement:4 coarse sand) Light shade pigment using white cement(HSR 10.26.1)

Regarding terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mudplaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1 :3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal ofunserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge.(HSR 30.9)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing thesurface smooth including necessary repairs to scratches etc. complete.(HSR 30.22) Note 1 :-In case of any difference in the unit & nomenclature of any of the HSR items of civil,PH work depicted in this DNIT and that given in HSR,the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (Make/brand exhibited in HSR and exhibited in approved standard documents) as approved by the Engineer-in-charge,while executing various items/work at site. 3. HSR items beyond DNIT shall be paid as per HSR+Ceiling premium. No extra rate shall be payable.