SPECIAL REPAIRS INCL ADDN / ALTN TO TYPE-II AND III RESIDENTIAL ACCN (PHASE-III) INCL BLDG NOS P-267 (08 QTRS), P-270 (06 QTRS), P-271 (04 QTRS), P-05 (06 QTRS), P-85 (04 QTRS), P-92 (24 QTRS) AND P-187 (06 QTRS) IN VARUNA RESIDENTIAL COMPLEX AT NPOL

Amount

Demolishing cement concrete manually/ by mechanical means including disposal of material exceeding 50 metres lead, complete all as specified and directed.

Providing and laying in position Plain cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) of specified grade, 75 mm thick, including the cost of centering and shuttering - All work upto plinth level :as in paving/ plinth protection laid in panels, finished even and smooth without using extra cement, complete all as specified and directed.

Providing and laying in position Plain cement concrete of specified grade all work upto plinth level as in surface drains including and channels in 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources including extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc, complete all as specified and directed.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm, complete all as specified and directed.

Providing and laying 7 to 8 mm thickness Ceramic floor tiles (Matt / Anti skid finish) of size 300mm x 300 mm of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid over and including 20 mm thick screed bed of cement mortar1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3Kg/ sqm including pointing the joints with white cement and matching pigments etc., complete all as specified and directed.

Providing and laying 10 mm thickness vitrified Ceramic floor tiles of size exceeding 0.18 Sqm but not exceeding 0.38 Sqm of 1st quality conforming to IS : 15622, of approved make, in all colours, shades,except White, Ivory, Grey, Fume Red Brown, laid over and including 20 mm thick screed bed in cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigments etc.,complete all as specified and directed.

Providing and laying 7 to 8 mm thickness Glazed Ceramic of 1st quality wall tiles conforming to IS: 15622 of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by AGE(I), in skirting, risers of steps and dados, laid over and including 12 mm thick plaster in cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete all as specified and directed.

Providing and laying 7 to 8 mm thickness Glazed Ceramic of 1st quality floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by AGE(I) in skirting, risers of steps and dados laid over and including 12 mm thick plaster in cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete all as specified and directed.

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed.

M&L for 20 mm thick Kota stone slab flooring laid over and including 20 mm thick screed bed in cement mortar 1:4 (1 Cement : 4 Coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing, complete all as specified and directed.

M&L for 18 mm thick Granite stone slab colour black, cherry / Ruby red gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over and including 20 mm thick screed bed in cement mortar 1:4 (1 Cement : 4 Coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels complete all as specified and directed.

M&L for 20 mm thick Kota stone slab in risers of steps, skirting, dado and pillars laid over and including 12 mm thick plaster in cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete all as specified and directed.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and directed.

M&L for 12 mm cement plaster in CM 1:4 (1 cement: 4 fine sand) on walls, complete all as specified and directed.

M&L for 12 mm cement plaster in CM 1:6 (1 cement: 6 fine sand) on walls, complete all as specified and directed.

M&L for 15 mm cement plaster on the rough side of single or half brick wall in CM 1:4 (1 cement: 4 fine sand). Extra for providing and mixing water proofing material in cement per bag of plaster work in proportion recommended by the manufacturers complete all as specified and directed.

M&L for applying/finishing walls with two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives (Two coats applied @ 1.43Ltr/ 10 sqm each coat) over and including priming coat of exterior primer applied @ 0.90 Ltr/10 sqm over two coats of wall care exterior putty, complete all as specified and directed.

M&L for distempering two coats with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over a coat of water thinnable cement primer over two coats of white cement based putty of average thickness 1 mm, over the newly plastered wall surface to prepare the surface even and smooth complete, as per manufacturer's specification, complete all as specified and directed.

M&L for Finishing walls with Acrylic Smooth exterior anti-fungal paint of required shade : New work (Two coats applied @ 1.67Ltr/10 sqm each coat) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L for Preparation surfaces and Applying White washing with lime to give an even shade old work (one coat) complete all as specified and directed.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete all as specified and directed.

M&L for distempering two coats with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of water thinnable cement primer over and including two coats of white cement based putty of average thickness1 mm, over the old prepared wall surface to prepare the surface even and smooth complete, as per manufacturer's specification complete all as specified and directed.

M&L for complete removal of old paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. and applying/finishing walls with two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives (Two coats applied @ 1.43 Ltr/ 10 sqm each coat) over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over and including two coats of wall care exterior putty and complete all as specified and directed.

M&L for two coats of weather proof exterior emulsion paint on old ceilling surfaces over and including a coat of primer after complete removal of existing treatment, complete all as specified and directed.

M&L for Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration, complete all as specified and directed.

Supplying chemical emulsion in sealed containers including delivery as Chlorpyriphos/ Lindane emulsifiable concentrate of 20% complete all as specified and directed.

M&L for Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion Treatment of soil under existing floors using chemical emulsion @ 250 ml per hole, 150mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration and complete all as specified and directed.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below complete all as specified and directed.

Providing and fixing factory made single extruded Frame size 65 x 100 mm WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body thread star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length (M.S hold fast/lugs or SS dash fasteners shall be paid for separately) complete all as specified and directed.

Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete all as specified and directed by Engr-in-Charge.

Providing and fixing factory made single extruded Frame size 45 x 70 mm WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body thread star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete all as specified and directed by Engr-in-Charge.

Providing and fixing factory made single extruded 35 mm thick WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.(Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete all as specified and directed.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete Double strip (horizontal type) complete all as specified and directed.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick, Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading complete all as specified and directed.

Providing and fixing to existing door frames 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete all as specified and directed (For W.C. and bathroom door shutter).

Providing and Fixing factory made UPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, complete all as specified and directed.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, (Single / double glass panes, wire mesh and silicon sealent shall be paid separately).

Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) complete all as specified and directed.

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) complete all as specified and directed by Engr-in-Charge.

S&F Aluminimum anodised deco grill of 150X150mm fitted with 'C' channel fixed with wall and complete all as specified and directed.

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 100x58x1.90 mm complete all as specified and directed.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. 150x10 mm. complete all as specified and directed.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm complete all as specified and directed.

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm complete all as specified and directed.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete all as specified and directed.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper complete all as specified and directed.

M&L for Painting two coats on new wood work with synthetic enamel paint of approved brand and manufacture to give an even shade over and including applying a priming coat with ready mixed pink or Grey primer of approved brand and manufacture, complete all as specified and directed.

Providing and fixing White Vitreous China Wash basin of size 630x450 mm with C.I. brackets, 15 mm CP brass pillar taps, 32 mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required, complete all as specified and directed.

Providing and fixing uplasticised PVC connection pipe with brass unions: 45 cm length and 15 mm nominal bore, complete all as specified and directed.

S&F PVC (SWR) floor trap with and including, plain / single hole chromium plated grating including jointing to waste pipe with solvent cement, 75mm dia, complete all as specified and directed.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 50 mm nominal dia Pipes for kitchen waste pipe, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete all as specified and directed. Internal work - Exposed on wall complete all as specified and directed.

Dismantling WC Pan of all sizes including disposal of dismantled materials i/c malba etc, complete all as specified and directed.

Providing and fixing White Vitreous china Orissa pattern WC pan of size 580x440 mm with integral type foot rests, squatting pan (Indian type WC pan) with 100 mm sand cast Iron P or S trap, including 10 litre low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required, complete all as specified and directed.

Providing and fixing white vitreous china pedestal type water closet (European type WC pan) with seat and lid, 10 litre low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid complete all as specified and directed.

Providing and fixing of cabinet mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357mm, complete all as specified and directed.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. etc complete all as specified and directed.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter complete all as specified and directed.

Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen sink with drain board of size 510x1040 mm bowl depth 250 mm as per IS:13983 with CI brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required, complete all as specified and directed.

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete, 32 mm dia, flexible pipe, complete all as specified and directed.

Dismantling 15 to 40 mm dia GI pipe including stacking of dismantled pipes (within 50 metres lead) complete all as specified and directed.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 15 mm nominal dia Pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the walls etc complete all as specified and directed.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 20 mm nominal dia Pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed. Concealed work, including cutting chases and making good the walls etc.

Providing and fixing CP brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore and complete all as specified and directed.

Providing and fixing CP brass two-in-one bib cock of approved quality conforming to IS:8931 :15 mm nominal bore and complete all as specified and directed.

Providing and fixing CP brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 of 15 mm nominal bore, complete all as specified and directed.

S&F in repairs Stop valves/angle valves, chromium plated fancy type with long shank and cup 15 mm bore fixed in repairs, complete all as specified and directed.

Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) : 20 mm nominal bore and complete all as specified and directed.

M&L for Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing GI pipe etc complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F PVC(SWR) pipes 110 mm dia single socketed in any length with rubber ring joints laid under floor or on walls fixed as soil waste/vent pipes including taking up or down existing PVC/CI pipes and connections complete all as specified and directed.

S&F PVC(SWR) pipes 75mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil waste/vent pipes including taking up or down existing PVC pipes and connections complete all as specified and directed.

S&F PVC(SWR) bends any radius, 110mm bore with / without access door, complete all as specified and directed.

S&F PVC(SWR) reducers 110 mm bore.complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75mm bore with / without access door, complete all as specified and directed.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms, complete all as specified and directed.

Demolishing brick in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed.

Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level in Cement mortar 1:6 (1 cement : 6 coarse sand) complete all as specified and directed.

M&L for 12 mm cement plaster in CM 1:4 (1 cement: 4 fine sand) complete all as specified and directed.

Demolishing stone rubble masonry in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed.

M&L for Random rubble masonry with hard stone in superstructure in cement mortar above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) in retaining walls,return walls etc complete all as specified and directed.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing in 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources complete all as specified and directed.

Demolishing RCC work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead, complete all as specified and directed.

Providing and placing in position precast reinforced cement concrete waffle units, square or rectangular, as per design and shape for floors and roofs in 1:1½:3 (1 Cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 10 mm nominal size derived from natural sources), including flush or deep ruled pointing at joints in Cement mortar 1:2 (1 Cement : 2 Fine sand), form work in precasting, handling, hoisting, centering and erection complete for all floor levels but, excluding the cost of reinforcement for slabs and similar work and complete all as specified and directed.

M&L for Steel reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more complete all as specified and directed.

M& L for mechanical cleaning of surface to make it free from any bituminous residue /dirt, oil and Greece etc all as specified and directed by GE/Engr-in-Charge. (a) M&L for cracks treatment by cutting open cracks and cleaning it from dirt/loose materials etc and filling with polyurethane based sealant with and including application of PU based primer all as directed by GE/Engr-in-Charge. (b) M&L for applying water based polyurethane modified dispersion (single component, cold applied, non toxic, VOC complaint) in 03 coats including 01 coat of primer of same materials after dilution of water at 50% or specific primer matching same materials complete all as specified and directed.

Properties of Polyurethane based chemical shall confirm to following Technical Parameters:- (i) Highly Elastic. (ii) UV Resistance. (iii) Adhesion to concrete. (iv) Tensile strength – not less than 2.0 N /Sq.mm for free film. (v) Elongation – not less than 300%. (vi) Solid content by weight- not less than 60% (vii) Air/water permeability BSEN 12390 at 5 bar -72 hours should be NIL and minimum dry film thickness of water proofing membrane must be 1.0 mm. (viii) Accelerated weathering (ASTM453) : Pass 1000 hours. (ix) Reaction to fire – non inflammable.

Supply and fixing heat resistance terrace tile size (300x300x20)mm thick with SRI (Solar reflective index) > 78, solar reflection> 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace laid on 20mm thick cement sand mortar and grouting incl rubble polishing complete all as specified and directed.

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level complete all as specified and directed.

Providing and placing on terrace (at all floor levels) polyethylene water storage tanks(White colour), 2000/1000/500 litres capacity, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tan complete all as specified and directed.

Providing and fixing PTMT Ball valve of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ HPHD plastic ball , 25 mm nominal bore, complete all as specified and directed.

Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) : 20 mm nominal bore complete all as specified and directed.

S&F Stainless steel plate rack, 1.00 mm thick for kitchen size 600x750x300mm, complete all as specified and directed.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size), complete all as specified and directed.

M&L for Painting two coats of synthetic enamel paint on new steel surfaces with approved brand and manufacture to give an even shade, on over and including a coat of red oxide primer of approved brand and manufacture, complete all as specified and directed.

S&F Health faucet, brass body with 1m SS braided rubber hose pipe & wall hook complete all as specified and as directed by Engineer-in-Charge, complete all as specified and directed.

Providing and fixing brass curtain rods 25 mm diameter of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete all as specified and directed.

M&L for writing letters or figures (Block.Roman, Italic or Indian) not exceeding 30 cm high in front of each quarters, meter box of concerned quarters and including building No of each block written on minimum two places of wall etc, complete all as specified and directed.

Excavating holes more than 0.10 cum & upto 0.5 cum including getting out in all kind of soil, the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m, complete all as specified and directed.

Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering - All work up to plinth level in 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) as in Foundation base, filling of post holes etc, complete all as specified and directed.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by GE) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete all as specified and directed.

M&L for Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. Hot finished welded type tubes, complete all as specified and directed.

Supply and filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete all as specified and directed.

Providing and laying factory made chamfered edge cement concrete paver blocks of 80 mm thick CC paver block of M-40 grade with approved color design and pattern in footpath, parks, lawns, drive ways or light traffic parking etc of required strength, thickness & size/shape made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand compacting and proper embedding /laying of inter locking paver blocks into the sand beding layer through vibratory compaction by using plate vibrator , filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Providing and laying cement concrete in retaining walls, return wall, walls (any thickness) including attached pilaster, columns, piers, abutments, pillars, poets, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc upto floor five level excluding the cost of centering, shuttering and finishing 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources) complete all as specified and directed.

Taking down carefully old and unserviceable aluminium point wiring for light/fan/socket or power point complete including fittings such as switches, ceiling rose, pendents, regulators, sockets, bell, distribution boards and MCB's etc and making good disturbed surface of walls. floors etc to match with the existing surface complete all as specified and directed.

Point wiring for light point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit,with modular switch,modular plate and cover with GI box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc. complete all as specified and directed.

Point wiring for fanpoint/Exhaust point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, with modular switch,modular plate and cover with GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required .

Point wiring for call bell Point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit,with modular switch,modular plate and cover with GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. complete all as specified and directed.

Point wiring for 5Amp socket outlet point on independent board with 2x 1.5 sq mm single core PVC insulated and unsheathed FRLS cable, 1100 volts grade IS -694 marked with multistandard copper conductors and earth continuty wire with similar 1x1.5 sq mm cable (incl connecting to earth dolly) drawn drawn through and single core cable in surface/recessed medium class PVC conduit as required at site complete all as specified and directed.

Point wiring for 5 Amp socket outlet point on same board with 2x 1.5 sq mm single core PVC insulated and unsheathed FRLS cable, 1100 volts grade IS -694 marked with multistandard copper conductors and earth continuty wire with similar 1x1.5 sq mm cable (incl connecting to earth dolly) drawn through and single core cable in surface/recessed medium class PVC conduit as required at site complete all as specified and directed.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper single core cable in surface/recessed PVC conduit medium grade, 2 way modular switch, modular plate and cover with GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etccomplete all as specified and directed.

All as per item No. 108 above but wiring for circuit alongwith 2x 2.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1x2.5 sq.mm copper cable as as earth wire for 16/15 power plug/socket complete all as specified and directed.

All as per item No 108 above but wiring for circuit alongwith 2x4 sq.mm FRLS PVC insulated copper conductor single core cable and 1x4 sq.mm copper cable as as earth wire for 16/15 power plug/socket or industrial socket. (FOR gyser & Ac Connection) complete all as specified and directed.

Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess,including providing and fixing 3 pin 5/6 A modular switch and 5/6A modular socket ,connection etc for Indepandant & same board complete all as specified and directed.

Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess,including providing and fixing 3 pin 15/16 A modular switch and 15/16A modular socket ,connection etc. as required at site complete all as specified and directed.

S&F call bell music type 230/250 volts (Ding dong type) complete all as specified and directed.

S&F ceiling rose PVC polycarbonate three terminal surface bakelitecomplete all as specified and directed.

Supply and fixing PVC Batten /Angle holder including all connections etc complete all as specified and directed.

Supply and fixing LED Lamp 9 watt complete all as specified and directed.

Supply & Fixing LED light fitting surface and wall mounted LED batten with aluminium housing & integrated electronic driver 20 W with one no LED tube , incl connecting up with three core flexible copper conductor of suitable size complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220v AC decorative type with driver holder and LED Lamp including connecting up with three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fixing building security light fitting LED 45 W , Pressure die cast aluminium housing with toughnesd glass with Glare free Secondary lens having >110lm/W ; IP66 Protection ; 10KV -SPD ; Driver unit should be access from outside for easy maintanace with suitable GI bracket including clamp & nut/bolts etc complete all as specified and directed.

Dismantling of old Ceiling fan and painting the same with one or more coats of spray painting with synthetics enamel paint of approved brand and manufacture to give shade,including cleaning of surface with detergent and replacing the damaged rubber reel,nuts and bolts with washers and safety pins,reinstalling the same complete all as specified and directed.

S&F Electronic ceiling fan regulator, modular type 2 module stepped type heavy duty suitable to work on 230 volts complete all as specified and directed.

Dismantling of old unserviceable Ceiling fan & Supply, installation, testing and commissioning of 1200 mm sweep BEE 5 Star rated, ceiling fan with Brush less Direct Current (BLDC ) Motor,class of insulation :B, 3 Nos. blades, 30 cm long down rod, 2 Nos canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9,Service Value (CM/M/W) minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019 ).THD less 10% remote or electronic regulator units for speed control and all remaining accessories including safety pin, nut bolts,washers,temperature rises = 75 drgree C (max),insulation resistance more than 2 mega ohms,suitable for 230V Hz,single phase AC Supply,earthing etc. including writing MES number on ceiling fan motor complete all as specified and directed.

Dismantling of old unserviceable Exhaust fan and Supply,installation,testing and commissioning of Exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V 50Hz single phase AC supply, 300 mm sweep including provision of 3 core 1.0 Sq mm cable from ceiling rose to exhaust fan including writing MES number on exhaust fan motor complete all as specified and as directed .

Supply & Fix VTPN DB with MCCB incomer ,Metal double door, 415 V, three phase,4 way ready to use DBs provided with Neutral Bar, Mechanical Impact Strenth IK 09 , Insulated busbar assembly, cement spill protector, color-coded interconnecting wire set, cable ties blanking plates and circuits identification labels suitable for MCCB's upto 100 Amp as I/C (Frame 1) and MCBs (TP/SP) as outgoing, IP 43 protection, module Optium F2+8+8+8, conforming to IS 8623-1 & 3, IEC 61439-1 & 3 including complete all as specified and directed.

Providing and fixing 100 A and breaking capacity 36KA,Four Pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panels,making connections,etccomplete all as specified and directed.(As a incommer to VTPN DB)

Providing and fixing 63 A and breaking capacity 36KA,Four Pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panels,making connections,etc.as required. ( As a incommer to VTPN DB)

Supply and fixing 5 A to 32 A Single pole and neutral rating,240/415V,10KA "C" curve,miniature circuit breaker suitable for inductive load of single poles and neutral in the existing MCB DB complete with connections, testing and commissioning etc, complete all as specified and directed.

Supply and fixing 5 A to 32 A Single pole rating, 240/415V, 10KA "C" curve,miniature circuit breaker suitable for inductive load of single poles and neutral in the existing MCB DB complete with connections,testing and commissioning etc, complete all as specified and directed.

Supply and fixing 20A,240 V, SPN Industrial type socket outlet with 2 pole and earth,metal encloser plug top alongwith 20A "C" curve SP,MCB in sheet steel enclosure ,on surface or in recess, with chained metal cover for socket out let and complete with connections,testing and commissioning etc complete all as specified and directed. (For Geyser/ AC Connection )

Supply and fixing MCB distribution board single pole and neutral 12 way, Double door sheet steel, 240 V, on surface /recess,complete with tinned copper bus bar ,neutral bus bar,din bar, interconnections, powder painted including earthing etc complete all as specified and directed.

Supply and fixing MCB distribution board single pole and neutral 2 way, Single door sheet steel, 240 V, on surface /recess, complete with tinned copper bus bar, neutral bus bar, din bar, interconnections, powder painted including earthing etc as required (For scootor Garrage/storage )

Taking down carefully old and unserviceable aluminium Submain wiring & M&L for sub main wiring with 2 run single core 6 Sqmm PVC insulated unsheathed multistranded , FRLS copper conductor cable in recessed /surface medium class PVC conduit and its accessories and connecting terminals to DBs/switch board including providing 2 run of 6 sqmm PVC insulated unsheathed multi stranded FRLS copper cable as earth continuity conductor and connecting to common earth dolly, complete ll as specified and directed .

Taking down old unserviceable UG Cable of any size and Supply and fixing/ testing XLPE insulated, screened, PVC bedded galvanized steal strip or wire armoured electric cables( heavy duty) 1100 volt grade with stranded aluminium conductor size 6.0 Sqmm, 2 Core complete all as specified and directed (For electrical connection to DB at garrage)

Supply and fixing TV antenna/Co Axial socket outlet modular on the existing modular plates and switch box including connection but excluding modular plates etc. complete all as specified and directed.

M&L for modular metal flush mounting boxes (75mmX 75mmX60mm) ,on surface or recess with suitable size of phenolic laminated sheet/ modular sheets in front including painting complete all as specified and directed.

Supply and drawing Co-axial TV cable RG-6 grade 0.7mm solid copper conductor PE insulated, Shielded with fine tinned copper braid and protected with PVC sheathed in the existing surface/ recessed steel/ PVC conduit as required including all necessary connections complete as specified and directed.

Supply and fixing of 25 mm sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit complete all as specified and directed.

M&L for Earthing complete with using galvanised steel earth plate 60 cm X 60 cm X 6 mm thick electrode , buried directly in ground including acessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 m long etc with charcoal/ coke and salt complete all as specified and directed.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I Wire in 15 mm dia G.I pipe from earth electrode including connection with G.I thimble excavation and refilling complete all as specified and directed.

Taking down energy meter from existing position by disconnecting all the electric connections, note down the initial reading , painting / marking of quarter number on each meters by means of suitable paint and refixing the same on its original position complete all as specified and directed.

S&F of Meter panel box 2mm thick MS sheet powder coated of size 1.4m x1.4m X 0.25m split in two parts 0.1X 1.4 m on top for refixing the meters and .4X 1 m for fixing of MCB TPN DB. The top portion should be provided with glass of size 10cm x 10cm infront of each meters to facilited recording of meter reading and including provision of wooden block of suitable size to fix the meters and DBs, door with locking arrangement and box to be fabricated such as the MCBs can be operated form out side including Removing of existing old & rusty meter Panel box (9 Nos). Note:Rate quoted also includes fixing of the DB completely on angle frame with necessary cable for internal wiring in the DB, lugs insulators etc complete all as specified and directed.

Dismantling GI pipes of following sizes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead complete all as specified and directed :-

15 mm to 40 mm nominal bore

Above 40 mm nominal bore

Providing and fixing of 80 mm dia Unplasticised PVC Pipes (UPVC), of presure rating 10 kgf/cm2 laid in trenches complete all as specified and directed.

Providing and fixing of 50 mm dia Unplasticised PVC Pipes(UPVC), of presure rating 10 kgf/cm2 laid in trenches complete all as specified and directed.

Providing and fixing of 40 mm dia Unplasticised PVC Pipes(UPVC), of presure rating 10 kgf/cm2 laid in trenches complete all as specified and directed.

All as per item No 146 here-in-before but of size 25 mm dia

All as per item No 146 here-in-before but of size 20 mm dia

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for asurements and disposal of unserviceable material as directed, within a lead of 50 m : Pipes, cables etc. not exceeding 80 mm dia complete all as specified and directed.

Supply and fix in repairs gun metal gate valve of size 80 mm ISI marked with iron wheel head screwed both ends complete all as specified and directed.

All as per item No. 150 above but 50 mm bore

All as per item No. 150 above but 40 mm bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm nominal bore complete all as specified and directed.

All as per item No. 153 above but of size 20 mm dia.

S&F float valve synthetic(PVC) of size 25 mm dia high pressure with polythene ball of size 6" dia and flynut including taking down old one complete all as specified and directed.

M&L for Construction of brick masonry valve pit of internal dimension 60 x 60 x 60 cm depth with sub class 'B' bricks in CM (1:4) and 10 mm thick plastering in CM (1:4), PCC (1:4:8) type D2 (Using 40 mm graded broken stone aggregate) as in foundation lean concrete, PCC (1:4:8) type CI (using 20 mm graded broken stone aggregate) as in bedding and copping MS frame with 40 x 40 x 6 mm angle iron and 6 mm thick MS sheet cover plate with locking arrangements, hinges and two coats of synthetic enamel paint over one coat of red oxide primer including preparation of surface, two coats of white wash on plastered surface (exposed to view) including necessary excavation in soft loose, soil, returning filling in and removal of surplus soil to a distance not exceeding 50 m, complete all as specified and directed.

M&L for Dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material up to a lead of 1 kilometre complete all as specified and directed.

M&L for Plain cement concrete in 1:4:8 (1 cement : 4 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 8 graded stone aggregate 40 mm nominal size Recycled Aggregate (RA) complete all as specified and directed.

M&L for Cutting the exisitng GI pipe of size 80 mm dia and providing & inserting tee of size 80 x 80 x 40 mm for taking branch connection including necessary threading, earth work, returning, refilling etc complete all as specified and directed.

Kurian And Varghese (BID ID -3462406)

WELTRONENGINEERINGSERVICES (BID ID -3462572)

K. VENKATESH NAIDU (BID ID -3462726)

M.J.JOY AND COMPANY (BID ID -3462366)

B5BUILDING SOLUTIONS (BID ID -3466235)

ROY CONSTRUCTION CO (BID ID -3467995)