Special repair of maize lab and other rooms at RRS Uchani Karnal. (including PH and EI works)

Amount

Civil work 1 to 45:- Dismantling brick work, tile masonry or tile lining and tile terracing {HSR 8.5(b)} (b) in cement

Dismantling concrete (HSR 8.6 (e)} (e) reinforced cement concrete with cleaning and straightening and cutting of bars if required

Dismantling concrete {HSR 8.6(d)} (d) cement concrete plain 1:2:4 mix

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantled (a)doors. (HSR 8.18(a)}

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantled (b)windows (HSR 8.18(b)}

Dismantling cement conglomerate/terrazzo floors 25 mm to 50 mm thick without concrete base. {HSR 8.26}

Scraping {HSR 8.32 (a) } (a) White wash and colour wash

Scraping {HSR 8.32(c)} (c) Cement plaster

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth {HSR 10.41}

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in first storey upto 4 metres above plinth level (HSR 10.59 + note) (2nd storey)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects. (HSR 10.81)

Extra over item Nos. 10.79 to 10.94 , if 1:1.5:3 mix is used, instead of 1:2:4 {HSR 10.95(a)}

11.43 cm thick brick wall laid in cement sand mortar 1:4 without reinforcement , in foundation and plinth (HSR 11.47)

Providing and fixing factory manufactured jali of reinforced cement concrete consisting of cement, coarse sand and 10 mm and down gauge bajri in the ratio of 1:1:2 with 8 mm dia tor steel. Outer frame of the jali will be 50mm wide and 25mm thick and inner frame of jali will be 25mm wide and 25mm thick with smooth finish as per the design approved by the Engineer-in-Charge including fixing in position up to any height with cement sand mortar 1:4, complete in all respect. {HSR 11.103}

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in flooring laid in any patterns as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles (HSR 14.89) Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this.

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in skirting / dado laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles (HSR 14.90) Note : Tile shall be of premium quality (first quality of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this

Providing and fixing ceramic tiles/ anti skid tiles of size 400 mm x 400 mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles (HSR 14.91) Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colour, shades except burgundy, bottle green, black of any size of approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement coarse sand mortar 1:3 and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (HSR 14.92) (b) size of ceramic glazed tiles 300 mm x 450 mm

Providing edge moulding to 17-20 mm thick granite stone counters, vanities etc. including machine polished to edge to give high gloss finish etc., complete in all respects as directed by Engineer-in-Charge (moulding) (HSR 14.98) (i) single moulding

12 mm thick cement plaster 1:3 (HSR 15.4)

12 mm thick cement plaster 1:4 on walls (HSR 15.5)

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

Cement pointing 1:2 deep variety on brick and tile work (HSR 15.60)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead , linseed oil, varnish and chalk mitti including finishing the surface to required finish complete (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade (HSR 16.3)

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.5)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces {HSR 16.25}

Distempering with washable oil bound distemper (of approved manufacture) two coasts excluding priming coat on new work {HSR 16.57}

Providing two coats of exterior acrylic emulsion paint (HSR 16.79(b) (b) 1st quality

Providing and applying two coats of white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc., complete (J.K/ Birla make). (HSR 16.81)

Proving and fixing 35 mm thick glazed door and windows shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc. ( non-coniferous timber other than teak confirming to I.S. specifications No. 1003 kiln seasoned), with vertical styles and rails, as specified in the statement no.1 ( attached in the end of this chapter), with glass panes of 4 mm thickness , tongued and grooved including the cost of iron hinges , screws, chocks/cleats, stops , etc., complete fixed in position excluding the cost of tower bolt and handles but including the labour for fixing the same (Based on 17.30 (a) + 17.24(c)} (a) 35 mm thick ( 4 mm thick glass panes)

Wire gauze commercial hard wood such as hollock , champ, chikrassy , etc., ( Non –coniferous timber other than teak conforming to I.S. specification no. 1003 kiln seasoned) door and window shutters without springs housed in chowkats including chocks, iron hinges and screws, etc., complete fixed in position ( excluding the cost of tower bolt and handles but including the labour for fixing the same)- {HSR 17.31 (i)} (i)30 mm thick Note: Nothing shall be paid extra for additional vertical style (any size) if required by the Architect or by the Engineer-in-Charge)

Supplying and fixing hydraulic door closer, I.S.I. mark, with necessary screws , etc., complete- (HSR 17.82(b)} (b) I.S.I. designation No. II ( size of door 701 mm to 850 mm)

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (HSR 17.93(a)} (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges :- (iii) 35 mm thick

Providing and fixing Aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS;733 and IS; 1285 fixed with raw plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. aluminium sections shall be smooth rust free straight mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling C.P. brass/ stainless steel screws, all complete. (HSR 17.95) Fixed portion (Anodized Aluminium transparent or dyed to required shade according to IS;1868, minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS; 733 and IS;1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. Aluminium sections shall be smooth, rust free straight mitered and jointed mechanically wherever required including clear angle, Aluminium snap beading for glazing/ paneling C.P. brass/ stainless steel screws, etc. complete. (HSR 17.96) Shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including of cost of PVC/ neoprene gasket required including aluminium fitting.

Providing and fixing 12 mm thick pre laminated particle board flat pressed three layer or graded wood particle board conforming to IS;12823 grade I type II in paneling fixed in aluminium doors. Windows shutters and partition frames with CP brass/ stainless steel screws etc. complete. (HSR 17.97(b)} (b) Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, windows, ventilator shutter and partitions etc. with PVC/ neoprene gasket etc. complete (cost of aluminium snap beading shall be paid in basic items). {HSR 17.98(b)} (b) With float glass panes of 5.00 mm thickness.

Steel reinforcement TMT bars FE-500 EQR-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, blinding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/ depths/ storeys/ basements etc. Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 18.22)

Supplying and fixing glass panes including special metal sash putty of approved make(HSR 18.30(b)} (b) glass panes 4 mm thick, exceeding 40 sq dm areas

Racking out joints in cement mortar (making zhiri in existing tile terracing) uprooting the grass and preparing the surface for re-pointing including disposal of rubbish with a lead of 2 K.M. complete in all respect as directed by the Engineer-in-charge (NS)

Providing and applying two coats of Dr. Fixit Pidicrete URP – SBR Latex (Pidilite make) solution made of URP + cement in the proportion of 1:1.5 (as recommended by the manufacturer) on deteriorated concrete surfaces of slab and columns, complete in all respects as directed by the Engineer-in-Charge.(NS)

Providing and fixing 15 mm to 18 mm thick Z-Black granite stone (polished) on worktop laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade including rubbing and polishing, complete. (NS)

Providing and fixing 25 mm dia stainless steel curtain rods weighing 0.560 kg/metre with brackets & side covers (balls) of Vista make, clamps, plastic gutties/rawl plugs etc. complete in all respects. (NS)

PH work 46 to 70:- Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and specials tees, bends, sockets elbows etc. inside building and testing etc. complete including cutting threading. {HSR 28.18} INCLUDING COST OF SPECIALS (i) 15 mm internal diameter of pipe line

(ii) 20 mm internal diameter of pipe line

(iii) 25 mm internal diameter of pipe line

Extra for fixing and jointing union couplings in G.I and W.I pipe lines. {HSR 28.21} (c) 25 mm internal diameter

(f) 50 mm internal diameter

Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I pipelines laid in the ground or inside buildings including cartage from divisional stores or nearest railway station to site of works. {HSR 28.29} (i) 25 mm internal diameter

Providing and fixing in position best Indian make European type water closet suite with concealed ‘P’ of ‘S’ trap with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item No. 30.3 above (without cost of C.I. high level flushing cisterns) {based on HSR 30.6(i)} (White)

Providing and fixing in position best Indian make (ordinary) lavatory suites consisting of Lavatory in vitreous china ware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary, R.S or C.I brackets for building into wall including painting;32 mm C.P. brass waste with C.P brass chain and rubber plug;15 mm C.P brass screw down pillar tap with jamnuts or couplings best design ( as approved by the Engineer-in-charge) all fittings best Indian make and; to the approval of the Engineer-in-chargeall brass work chromium plated and complete in all respects including cutting and making good the walls and floors and painting of fittings etc. (HSR 30.41) (iv) size 550 mm x400 mm with one no tap

Providing and fixing in position 15 mm i/d C.P brass bib cocks of best quality ( as required by the Engineer-in-charge) {HSR 30.75 (c)} (c) bib cock

Providing and fixing in position H.C.I soil waste vent or antisyphonage pipes to I.S.I specifications of E.L.C manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floors etc. and making good to its original condition but excluding cost of lead jointing. (HSR 30.84) (a)100 mm i/d

(b)75 mm i/d

Providing lead caulked joints to H.C.I pipes and specials conforming to I.S.I specification of E.L.C manufacture or any other reputed firm including cost of lead yarn, fuel and tools etc. (HSR 30.87) (a)100 mm i/d

(b)75 mm i/d

Providing and fixing H.C.I. floor traps I.S.I. marked of the self cleaning design with C.P. brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under the around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors, etc., minimum depth of water should be 150 mm with a minimum seal of 50 mm. (HSR 30.89) (b) With 75 mm internal dia outlet

Providing and fixing in position H.C.I specials for soil, waste, vent or anti-syphonage pipes to I.S.I marked including cutting and wastage etc/., and making good to its original condition but excluding cost of lead jointing. (HSR 30.91) (I) For 100 mm i/d pipe (i) Heal Rest Bend

(xxii) collars

(b) For 75 mm i/d pipe (xviii) Collar

Supply and fixing in position stainless steel sink made of 1 mm thick Salem stainless steel sheet along with fittings of Blue Star/ Jayna make or equivalent as per AISI 304 (18/8), complete in all respect. (NS) Bowl size = 560 mm x 405 mm x 178 mm Overall size = 610 mm x 460 mm x 178 mm

Providing and fixing in position PVC flushing cistern 8.0 ltrs. capacity of Hindware/Perryware/Cera make ISI marked, white, alongwith fittings complete in all respect. (NS)

Supply of GI pipe 'B' Class ISI Marked Ravindra/Jindal/Parkash(Surya) Make. (NS) (a)15 mm i/d

(b)20 mm i/d

(c)25 mm i/d

Supply of GI Union Couplings of UNIK/UNCO make . (NS) (a)25 mm i/d

(b) 50 mm i/d

Supply of Gun Metal Peet Valve ISI Marked of DRP/Leader/Bajaj make (NS) 25 mm i/d

EI work 71 to 99:- S/E of Blanking Sheet in existing distribution board (HSR 31.16)

S/E of MCBs/isolator 240/415 V in existing distribution board including making necessary connections :-( HSR 31.17 ) (ii) 6 to 32 amp. MCB SP

(ii) 6 to 32 Amp MCB SPN

(iii) 40 to 63 Amp MCB TP&N

S/E of fittings and accessories (HSR 31.18 ) (xi ) Bakelite angle / straight button holder large size

Misc. Dismantalling of old wiring points including necessary repair to the walls ( HSR 31.35 ) (a) Light , Fan , call bell points

(b) Wall sockets points

S/E of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe.( HSR 31.40 ) (i)Cable Size 1.5 sqmm

(iii) Cable Size 4.0 sqmm

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBs and ELCBs etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto to the entire satisfaction of the Engineer-in-charge of the work. ( HSR 31.41 ) (ii) 8-Way, SP&N

(iv)16 way SP&N

Supply and erection of PVC conduit pipe ISI marked (Medium) recessed in wall/ceiling etc. including cost of PVC bends, inspection box and all other material required to complete upto the entire satisfaction of Engineer-in-charge of work HSR 31.44 (b) 25mm dia

Pdg. & fixing modular type accessoriesm of app. Make in existing box including fixing and making necessary connections complete in all respect. ( HSR 31.56 ) 10 amp. 1 way switch

20 amp. Switch

10 amp. Socket

16 amp. Socket

Fan Regulator

Blanking Sheet

Pdg & fixig GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate with all labour and matrial required for the job.(HSR 31.57) 2 Module

3 Modules

6 Modules

8 Modules

12 Modules

S/E of AC ceiling far capacitor type complete with shackle 300mm down rod etc with rating 5 star (NS) i) 1200mm sweep Make:- Havells, Bajaj, Crompton, Wipro

S/I/T/C of push on/off type 25 & modular type motor starter switch ( white color ) for AC's including the cost of petty material required to complete the job upto the entire satisfaction of engineer incharge. (NS) Make:- Havells, Bajaj, Crompton, Wipro

S/E of recessed type 42 watt full window glare free opal difffuse LED panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be 4600 or above in cool day light (5600k to 6500k), Power factor >0.95, CRI (Ra) >80, LED lamp efficiency ≥140 lm/w, Average life >50000hours, complete with all accessories as required with connections. (Industrial) (NS) Make:- Havells, Bajaj, Crompton, Wipro

S/I/T/C of surface wall mounted LED < 20watt 4 feet long fitting with Epoxy powder coated white / grey extruded aluminium channel housing for efficient heat dissipation total system lumen of 20watt LED should be > 2000 or above in cool day light ( 5700 to 6500 K )power factor > 0.95 CRI > 80 , Avg. life > 50000 connection. (NS) Make Philiphs , Havells , wipro , bajaj , HPL

S/E of I/O Box for internet connection including I/O box , face plate and internet jack Make D-Link (NS)

S/E of Cat 6 wire for internet make D Link in existing pipe (NS)

M/s buildtech engineers and contractor