REPAIR TO JOINERY ROOF FLOORING CEILING PLASTERING SANITARY FITTING AND ALLIED SERVICES AT ASCON MAND TA 12 DOGRA DEWS DEPTA DSI GARHI SHOPPING COMPLEX UNIT AND OTM ACCN UNDER AGE BRI GE SOUTH UDHAMPUR

Amount

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar complete all as specified and directed.

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 bricks complete all as specified and directed.

All as per ser item No 2 above but except bricks complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Random rubble masonry built in cement mortar 1:6, uncoursed, well bonded, bedded and solidly hearted complete all as specified and directed.

All as per ser item No 5 above but except stones complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick below or above ground level complete all as specified and directed.

PCC type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in surface channel and drain beds including all necessary form work complete all as specified and directed.

PCC 50 mm thick type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and directed.

75 thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

Extra performing fair finished drain or channels cement concrete using extra cement including forms, mould, mitied/ stopped ends etc. complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

Rendering 15 mm thick in two layer (10 + 5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and directed. (Water proofing compound to be measured and paid for separately).

10 mm thick rendering on fair faces of brick works in cement mortar 1:6 finished even and smooth without using extra cement in cement mortar complete all as specified and directed.

05 mm thick rendering on fair faces of concrete such as chajjas/ceiling finished even and smooth without using extra cement in cement mortar 1:3 complete all as specified and directed. Note : Rate quoted by contractor deemed to be included for plastering chajjas to up to height of 10 mtrs.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

20 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

10 mm thick rendering on fair faces of brick works in cement mortar 1:4 finished rough for receiving tiles as in dado complete all as specified and directed.

7 mm to 8 mm thick non skid coloured ceramic tiles in floor (area of each tile exceeding 0.11 and not exceeding 0.18 sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments complete all as specified and directed.

All as per ser item No 21 above but in vertical surfaces complete all as specified and directed.

Coloured double charged Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of existing surfaces. complete all as specified and directed. Note : The contractor shall have no claim on difference what so ever on shade/colour of tile.

Coloured double charged Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.42sqm but not exceeding 1.00 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of existing surfaces. complete all as specified and directed. Note : The contractor shall have no claim on difference what so ever on shade/colour of tile.

All as per ser item No 24 above but in vertical surfaces complete all as specified and directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

150mm wide strip of makrana white marble 20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types complete all as specified and directed.

Coloured durastone heavy duty vitrified tiles 10 mm thick Sq/rectangular tiles area of each tile not exceeding 0.36 Sqm as in floors set and jointed in neat cement slurry and pointed in clooured cement to match the surface complete all as specified and directed. Note : The contractor shall have no claim on difference what so ever on shade /colour of tile.

All as per ser item No 29 above but in vertical surfaces complete all as specified and directed.

Cement concrete rich colored chequered tiles machine pressed with imported pigment smooth finish of size (300 mm x 300 mm or any size as approved 20 to 25 mm) thick set and jointed with neat cement slurry complete all as specified and directed.

15 mm to 18 mm thick granite stone slab as in shelves/vertical surfaces/platforms set and jointed in neat cement slurry, pointed in colored cement to match the shade including rubbing of moulding etc. complete all as specified and directed.

(300 mm x 600 mm x 7 mm/300 mm x 450 mm x 7 mm or 8 mm thick) coloured glazed ceramic tiles set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments in vertical surfaces complete all as specified and directed. Note : Contractor shall have no claim on colour or shade what so ever on this account.

Sand cushioning under floors including watering and consolidation complete all as specified and directed.

Coloured machine pressed/vibro mechanically floated interlocking paver block any shape and size confirming to IS - 15658-2006 of 60 mm thickness, M-35 grade, with topping of cement mixed with imported pigment colour and shape shall be approved and complete all as specified and directed.

Machine pressed (factory made) plain cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), kerb stone of any size, laid in trenches on edges of roads joints fitted in CM 1:4 including excavation in any type of soil, PCC bed, returning filling and removal of surplus soil to a distance not exceeding 50 m from the starting point complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise specified complete all as specified and directed.

Rolled section/tubular section as in main and cross beams, purlins, rafters, posts where connected to common rafter and running rails etc confirming to Fe-410-W complete all as specified and directed.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work,incl locking arrangement for water tanks and similar work conforming to Fe 290 Gd E-165 complete all as specified and directed.

Hard Drawn steel wire fabric cut to length bent to shape required and tying,welding to the angle iron frame etc complete all as specified and directed.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed.

AC designer composite ceiling board 4 to 6 mm thick in 600 x 600 mm panel confirming to IS-14682 type-B category-3 including GI frame, holdfast & suspenders complete all as specified and directed.

Dismantling asbestos corrugated or semi corrugated sheets as in roof covering including ridge etc complete all as specified and directed.

Pre painted galvalume aluminium zinc coating GI based corrugated sheets 0.60 mm thick of any colour having tensile strenght of 550/MPA as in roof covering, cladding to wall fixed with self taping screws complete all as specified and directed.

All as per ser item No 44 above but plain sheets as in ridges complete all as specified and directed.

6 mm thick asbestos cement corrugated sheets as in roof covering fixed with L or J hooks complete all as specified and directed.

All as per ser item No 46 above but fixing only complete all as specified and directed.

6 mm thick 2 piece screted ridge for corrugated or semi corrugated sheets fixed with L or J hooks complete all as specified and directed.

Roughing surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @3kg/Sqm mixed with water proofing compound including 20mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound complete all as specified and directed. (WPC shall be measured and paid separatley) Note : No extra cost shall be paid to contractor in r/o any removal of existing roof treatment.

Priming surfaces with bituminous primer confirming to IS-3384 @ 0.40kg/sqm, after drying of primer applying a coat of hot blown bitumen confirming to IS-702 @ 1.20 kg/sqm and layin polymeric water proofing membrane, five layerd with centre core of 90 micron high molecular density polythelene film (minimum weight 3.5 kg per sqm) with end over laps not less than 150 mm and side lap 75 mm complete all as specified and directed for sunken floor treatment or painting with solar reflective paint for roof surfaces.

Providing cement concrete in steps, seismic and other similar bands, pad paraping concrete ets and railings up to 60 cm in hieght, coping, kneeless apex stones, bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete all as specified and directed.

Supply only (LW+) water proofing liquid solution of Dr fixit/sikka or equivalent make complete all as specified and directed.

MS drapery rod powdered coated including brackets and necessary fitting "as in repair" complete all as specified and directed.

Demolition of and breaking up of PVC rain water pipes any dia fixed in any position complete all as specified and directed.

110 mm bore PVC (SWR) pipe single socketed, in any length with rubber joints fixed to walls complete all as specified and directed.

110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

Taking up or down steel tubing 15 mm bore including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20 mm bore including cleaning for refixing or removal to store complete all as specified and directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm dia complete all as specified and directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20 mm dia complete all as specified and directed.

Dismantling water tank of capacity exceeding 250 ltrs but not exceeding 500 ltrs complete all as specified and directed.

Dismantling water tank of capacity exceeding 500 ltrs but not exceeding 1000 ltrs complete all as specified and directed.

Rotational molded (Triple layered as per IS 12701) polyethylene water storage storage tank (cylindrical vertical with closed threaded top) hoisted and fixed in position including connecting inlet/outlet pipe connecting with necessary fittings including fixing of cover lid with screws all as required at site and specified in SSR part-I of capacity 500 litres complete all as specified and directed.

Rotational molded (Triple layered as per IS 12701) polyethylene water storage storage tank (cylindrical vertical with closed threaded top) hoisted and fixed in position including connecting inlet/outlet pipe connecting with necessary fittings all as required at site and specified in SSR part -I of capacity 1000 litres complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including cast iron P trap, bore of pipe 100 mm and provision of concrete bedding "as in repair" complete all as specified and directed.

Vitreous China wash down water closet pan pedestal pattern, white (excluding fixing bolts, flushing cistern and flush pipe) with P or S trap but including plastic water closet seal, seat cover, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including connection to drain and flush pipe fixed as in repair complete all as specified and directed.

Central hole Basin Mixer without Popup waste and 450 mm Long Braided Hoses, Cat Part No. CON-167 KNB or equivalent including necessary fittings complete all as specified and directed.

Bib Tap with wall flange, fancy type, cast copper alloy chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm in repair complete all as specified and directed. Cat Part No. CQT-23047 or equivalent

Stop valves of 15 mm bore, but fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions including necessary fitting as required at site as in repair complete all as specified and directed.

Glass shelf with chromium plated guard rails as in repair complete all as specified and directed. Cat Part No AQN -7771.

Health faucet (ABS Body) with 8mm dia, 1.2 meter long flexible tube & wall hook with all accessories all as approved and fixed as in repairs complete all as specified and directed. Cat Part No : ALD-587

Soap dish as in repair complete all as specified and directed. Cat Part No : AQN-7731 or eqivalent

Swivel Looking mirror of Cat part No. ACN- 1195 N as required at site as in repair as approved and complete all as specified and directed.

Towel ring round with round flange as in repair complete all as specified and directed. Cat Part No : ACN-1121N and eqivalent

Toilet paper holder as in repair complete all as specified and directed. Cat Part No : ACN-1153S.

Corner glass shelf with chromium plated rails incl brackets as in repair complete all as specified and directed. Cat Part No : ACN 1173 and eqivalent

PVC waste pipe 32 mm bore with cup and washers "as in repair" complete all as specified and directed.

15 mm bore Long body bib taps cast copper alloy with capstan head chromium plated screwed down screwed for iron pipe or brass ferrule "as in repair" complete all as specified and directed. CON-107KN and eqivalent

Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15 mm-90 gms/20 mm-125 gms) in repair complete all as specified and directed.

15 mm bore pillar tap cast copper alloy with capstan head chromium plated screwed down under high pressure with or without lettered hot or cold with long shank and fly nuts screwed for iron pipe complete all as specified and directed.

Concealed stop valve cast copper alloy fancy type chromium plated long shunk and cup screwed down high pressure with crutch or butterly handle screwed both ends for iron pipe or for unions "as in repair" complete all as specified and directed.

15 mm bore angle valve, cast copper alloy chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed "as in repair" complete all as specified and directed.

Brass CP shower rose 125 mm size "as in repair" complete all as specified and directed.

20 mm bore PTMT float valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule "as in repair" complete all as specified and directed.

Sand cast iron 'P' or S trap 100 mm bore for ind type w/c complete all as specified and directed.

Viterous China urinal half stall type white including CP spreader, waster pipe etc. "as in repair" complete all as specified and directed.

PVC flushing cistern 10 ltrs capacity with complete in let ball valve as in repair complete all as specified and directed.

Viterous china wash hand basin flat back size 580 x 450 mm excluding traps, waste, chain, plug and porcelain stopper including brackets "as in repair" complete all as specified and directed.

S&F in repair PVC connection 15mm bore with ptmt nuts of length 450mm

Complete removal of existing treatment and apply 1mm thick wall care putty on wall complete all as specified and directed.

Two coats of oil bound distamper on new surfaces over a coat of primer on internal walls complete all as specified and directed.

Two coats cement base paint on newly plastered surfaces including preparation of surfaces on external walls complete all as specified and directed.

Three coats of white wash on newly plastered ceiling surfaces including preparation of surfaces complete all as specified and directed.

Two coats of synthetic enamel paint on new steel surfaces including preparation over a coat of red oxide zinc chrome primer complete all as specified and directed.

Two coats of synthetic enamel paint on new wooden surfaces including preparation over a coat of pink primer complete all as specified and directed.

Demolition of cement concrete (reinforced) as in roof, floors (other than ground floor), beams, staircase, landing, chajjas and similar suspended work complete all as specified and directed.

Reinforced cement concrete 1:2:4 type B-0 (using 12.5 mm graded aggregate) as slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200 mm thick surface horizontal or sloping, fair finished surface of concrete complete all as specified and directed.

Mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Taking down chowkats or frame with shutter (without taking of shutter off shutters from frame) 1.5 sqm and not exceeding 4 sqm each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed.

All as per ser item No 100 above but not exceeding 1.5 sqm complete all as specified and directed.

Taking down shutters of any description exceeding 1 square metre not exceeding 2 square metre each complete all as specified and directed.

Taking down shutters of any description not exceeding 1 square metre each complete all as specified and directed.

Factory made PVC door frames of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube suitable for opening as per site condition complete all as specified and directed and shown on page No 160 of SSR Part-II.

Powder coated Anodised Aluminium frames for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

Powder coated aluminium anodised window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws etc. complete all as specified and directed.

Powder coated aluminium grill/guard bars to aluminium window complete all as specified and directed.

35 mm thick plain framed II nd class hard wood panelled factory made shutters (two panel or more panel) with lock rail and panel of 12 mm thick BWP commercial ply with size of rail and stiles as per IS 1003 (part-1) kin seasoned and chemically pressure treated complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling, of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed in drawing on sl page No 156 of SSR 2010 part-II.

Factory made, 2nd class hard wood 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauze etc complete all as specified and directed.

Mild steel, 300 mm, ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed.

10-12 mm thick frameless Swing Toughened Glass Door (single/double shutter), with etched design openable in both direction and including fixing clips, glass fins, stainless steel handles length exceeding 60 mm 02 Nos on each shutter including floor spring (Make : Hetich or equivalent), floor locks and all accessories complete all as specified and directed by Engr-in-Charge. Note : Door size as per site requirement.

35 mm thick flush shutters, premium quality, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Powder coated aluminium anodised door shutter shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws etc. complete all as specified and directed. (Thickness or powder coating not less than 50 micron)

Aluminium body heavy duty double action floor spring suitable for glass shutter at both side rotable complete all as specified and directed.

Aluminium door closer hydraulically regulated universal type, suitable for door shutters complete all as specified and directed.

18/19 mm thick pre-laminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

12 mm thick plywood grade BWR, type BB fixed with screw to timber frame work including dismantling complete all as specified and directed.

0.90 mm thick decorative choice of lamination type 1 of surface finish, colour and pattern as approved, fixed with aproved adhesive as per manufactur's insturctions complete all as specified and directed.

Prelaminated particle board 18/19 mm thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination as in kitchen cabinets/shutters fixed with screws to timber framework as in repairs complete all as specified and directed.

Continuous (Paino) hinges, stainless steel bright finish or electro-galvanized width of flap 30 mm (when open) complete all as specified and directed.

Hasp and staple size 100 mm powder coated with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames exceeding 1.5 sqm, glazed with putty or fixed with beads complete all as specified and directed. Note : Glass will be measured and paid for separately.

3 mm thick sheet glass, ordinary quality and glazing with wooden beading not exceeding 0.5 Sqm in each pane complete all as specified and directed.

3 mm thick figured glass, pin head type and glazing with wooden beading, not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56 mm nominal dia wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

S & F in repairs Galvanised mild steel wire cloth, 0.56 mm nominal dia wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

Mild steel cold rolled butt hinges medium weight 75 mm long, including fixing to pressed steel door frame.cupboard & Almirah if required complete all as specified and directed.

All as per ser item No 128 above but in repair complete all as specified and directed.

Mild steel cold rolled butt hinges medium weight 100 mm long fixed to pressed steel door frame if required complete all as specified and directed.

All as per ser item No 130 above but in repair complete all as specified and directed.

Aluminum alloy powder coated sliding door bolt 300 mm long and not less than 12 mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Aluminum anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and directed.

All as per ser item No 133 above but in repair complete all as specified and directed.

Aluminum handles cast type, anodised, 150 mm size complete all as specified and directed.

All as per ser item No 135 above but in repair complete all as specified and directed.

Aluminium alloy, anodised, 200 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruted sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Pressed steel frames size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete as specified supplied and fixed as in repair complete all as specified and directed.

Pressed steel frames size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete as specified supplied and fixed as in repair complete all as specified and directed.

One coat of synthetic enamel paint on old wooden surfaces of any description over 10cm width or girth including preparation of surfaces all as specified and directed.

One coat of synthetic enamel paint on old steel surfaces of any description over 10 cm width or girth including preparation of surfaces complete all as specified and directed.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Description all as per ser item No 142 as above here in before but without glazing bar complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately

Mild steel ventilators (Box type) factory made with top hung shutters and bottom fixed type shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg CEUZ/TD/1269/2008 Sh 1/3. (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required of internal dia of pipe 50/75/100 mm complete all as specified and directed.

100 mm bore cast iron soil, sand cast, waste and vent pipes in any length with or without ears, with cement joints fixed to walls complete all as specified and directed.

All as per ser item No 146 above but except pipe, any type complete all as specified and directed.

Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints fixed to walls, 75 mm dia, sand cast pipes including two coats of black Japan paint complete all as specified and directed.

All as per ser item No 148 above but except pipe, any type complete all as specified and directed.

50 mm bore cast iron soil, sand cast, waste and vent pipes in any length with or without ears, with cement joints fixed to wall, complete all as specified and directed.

All as per ser item No 150 above, but except pipe, any type complete all as specified and directed.

100 mm bore cast iron soil, sand cast, waste and vent pipes in any length with or without ears, with cement joints laid in trenches or in floors complete all as specified and directed.

All as per ser item No 152 above but 75 mm dia complete all as specified and directed.

Cast iron bends (any radius) with for 75 mm bore fitted with oval access doors in repair complete all as specified and directed.

Cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) for 100 mm bore fitted with oval access doors in repair complete all as specified and directed.

Cast iron branch pieces, single (equal of unequal), ordinary or inverted (spigot or socket type) or with parallel branches for 100 mm bore fitted oval access door in repair complete all as specified and directed.

Cast iron floor trap with dia of outlet 75 mm with CI grating including jointing to waste pipe fixed in cement concrete PCC 1:2:4 type B-1 in repair complete all as specified and directed.

All as per ser item No 157 but 100 mm complete all as specified and directed.

Cast iron cowl suitable for pipes of 50 mm bore in repair complete all as specified and directed.

Cast iron cowl suitable for pipes of 75 mm bore in repair complete all as specified and directed.

SODHI TRADING CORPORATION (BID ID -3065384)

s l sharma and sons (BID ID -3056349)