SMART COMPREHENSIVE DAY TO DAY MAINT INCLUDING B/R, E/M AND B/S IN OFFICERS MD ACCN AT MOTIBAGH ENCLAVE, PENTON RD, ROBERT RD, HUNTER RD, POTTINGER ROAD, NAGARWALA ROAD, PEARSON ROAD, CESSEL ROAD, KITCHENER ROAD ETC UNDER GE (N) AHMEDNAGAR

Amount

Dismantling, floor, hearth or wall tiling including cement mortar bedding/backing and removing all rubbish/dismantled material outside MD Land.

Demolition of plain cement concrete (unreinforced) in ground floor not exceeding 15 cm thick all as directed.

M&L Excavating over areas,n exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed by Engg-in-cgarge.

Removing excavated material exc.250m but n exc. 500m and deposited where directed.

M&L for moorum filling in floors or paving laid in layers n exe 15 cm thick spread leveled and rammed including watering complete all as specified and directed by Engg-in-charge

M&L for hard core of gauge etc 63 mm but n exc 100 mm deposited spread and levelled in layer n exc 15cm thick water and rammed etc complete all as specified and directed by Engg-in-charge

M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed.

M&L for renewing glazed tiles in patches, area n exc 5 sq. m. including removing and cleaning old tiles, preparing beds and laying or setting, jointing and pointing new or old tiles complete

M&L for Glazed colour ceramic tiles 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured as approved by GE as in dado / skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

M&L for joint free / rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,(400x400)mm as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free / rectified vitrified/ ceramic light shade coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile not exceeding 0.36 sqm,(600 x600)mm as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed

M&L for Virified Ceramic tiles dark shade/Double charged/ultra charged 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm (600 x 1200)mm , in floors etc. laid over and including roughning existing surface, making good the damaged surface, levelling and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

-Ditto- as per Sr item No 12 above but on skirting and backing coat of 10 mm thick in CM 1:4

Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor and removing all rubbish/dismantled material outside MD Land. all as directed.

M & L for Chequred cement concrete tiles with pigment 25 cm x 25 cm x 25 mm thick, set, jointed and pointed in neat cement slurry as in floors over and including screed bed of 15 mm thickness in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engineer-in-Charge

M&L for 20mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills, jambs, lintel etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in CM 1:4 jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and directed.

M&L for machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as directed.

M&L for 30 mm thick Rough dressed(shahabad) lime stone slab flooring, laid dry, jointed and pointed in cement mortar 1:3 as in floor/plinth etc over bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 in floor/plinth etc over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed

Fixing only 30-40mm thick rough dressed Shahabad stone as in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 including dismantling complete all as specified and directed

M&L for heavy duty vitrified paver tiles 30cm x 30cm x 10mm thick,approved by GE withnset,jointed and pointed in neat cement slurry with grey cement and pigment to match in floors,over and including screed bed or bedding a layer of 15 mm in cement mortar 1:6 complete all as specified and directed by Engg-in-charge.

Demolition of plain cement concrete solid block masonary built in cement mortar & removing all rubbish/dismantled material outside MD Land.all as directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water all as directed

M&L for rendering, 12 mm thick on stone surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed.

M&L for rendering, 10 mm thick on brick/concrete surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed.

M&L for rendering, 15 mm thick on stone/brick/ concrete surfaces in cement mortar 1:4 surfaces finished even and fair finish all as specified and directed.

M&L for 2 mm wall care putty on walls complete all as specified and directed by Engg-in-charge.

Dismantling of single layer manglore pattern in roofing & removing all rubbish/dismantled material outside MD Land.all as directed.

-ditto- as per Sr item No 29 above but bedded in cement morter

M&L for roofing tile, manglore pattern interlocking at sides joints laid dry

-ditto- all as per Sr item No 31 but except manglore pattern tiles

M&L Ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement morter 1:6

Dismantling timber scantling 40 sqcm and over in section, in any postion framed work as in scanging of main joist of roof & removing all rubbish/dismantled material outside MD Land.

-ditto- all as per Sr item No.32 in fillets,rails, posts, rafters purlins etc under 40 sqcm in section framed work & removing all rubbish/dismantled material outside MD Land.

Dismantling battens for tiles, shingles etc of any size including tilting fillets spacing exc 15 cm &removing all rubbish/dismantled material outside MD Land.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including ridge & removing all rubbish/dismantled material outside MD Land.all as directed.

M&L for second class hard wood in scantling of roof rafters, etc wrougt framed

S&F Pre-painted Galvalume sheet shall be 0.50mm thick (total coated thickness), 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge.

Supply and fix 0.50 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with, 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge.

S&F of steel work in post,joist,channel,angle, or tee section fixed independently,without connecting plates etc as per Fe 410-W (Grade-E-250 quality-A)

Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap all as directed.

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed.

Supply and fix in repairs wash hand basin vitreous China, flat back of size 550 X 400 mm including a pair of brackets, PTMT waste coupling, 32 mm dia PVC flexible waste pipe and connecting to stop valve and nahani trap all as directed.

M&L for Preparing new unplastered or plastered surfaces and applying two coats of oil bound distemper including chalk whitening on wall including smooth roller finish complete all as directed.

M & L for preparation of newly plastered surface of wall and apply two coats of cement based paint over a coat of alkali primer any height including scaffholding etc complete all as directed.

M&L for preparing old unplastered or plastered surfaces and applying one coats of oil bound distempering on walls all as directed.

--ditto-- all as per Sr item No. 47 above but two coat of OBD on old surface

M&L for preparing old painted surfaces of wall and applying two coats of cement based paint all as directed.

M&L for preparing old painted surfaces of wall and applying one coats of cement based paint all as directed.

M & L for preparation of old plastered treated surface of walls by brooming down and apply one coats of wheather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces complete all as directed.

M&L for preparation of old surfaces of wood of any description exc 10cm width/girth incl cleaning applying one coat of synthetic enamel all as specified directed by Engineer-in-charge.

M&L for preparation of old steel and iron surfaces, of any description, over 10 cm width or girth not other wise described and applying one coats of synthetic enamel paint over a coat of red oxide primer

Taking down chowkats or frames exc 1.5 Sq m but nexc 4.00 sqm with shutters (without taking off shutters from the frames) all as directed.

Taking down chowkats or frames n exc 1.5 Sq m with shutters (without taking off shutters from the frames) all as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each all as specified directed by Engineer-in-charge.

Taking down shutters of any description n exc 1 sqm each all as specified directed by Engineer-in-charge.

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

Supply and fixing 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

Supply and fix 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, all as directed.

Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face

Supply and fix galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed.

Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm

Supply and fix aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed 300mm long.

Supply and fix aluminium anodised barrel tower bolt of extruded section 200mm long.

Supply and fix aluminium anodised handles of extruded section 150mm long.

S&F in repair 300mm mild steel ordinary rat tail rod patteren door spring including roller and roller plate complete all as specified and directed

S&F in repair aluminium extruded section body door closer for aluminium door shutter hydraulically regulated,designation No 1 universal type,suitable for door shutter upto 700 mm in width and of weight not more than 35 kg and fixed.complete all as specified and directed.

S&F in repair 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor complete all as specified and directed.

S&F in repair Cylindrical Latch Door Lock Tubular (Dumbell lock) stainless steel finish fixed in door complete all as specified and directed by Engg-in-charge. Make:Godrej,Europhia and equivalent.

M&L for two coats of synthetic enamel paint over a coat of pink primer for new wooden surfaces of any description exc 10 cm width or girth including preparation of surfaces and smooth finish with roller all as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer for new steel surfaces of any description exc 10 cm width or girth including preparation of surfaces all as directed.

Supply and fix mild Steel 20 mm dia decorative powder coated curtain rods with fixing brackets fixed in repairscomplete all as specified and directed.

Supply and fix in repairs 32 mm dia PVC waste pipe(outlet pipe) plain fixed to waste coupling of WHB or Sink etc all as directed.

Supply and fix in repairs stainless steel kitchen sink matt finish with draining over all size 950 X 510 mm and bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed.

S&F stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge .

S&F in repair wall mixture, with provn for overhead shower all as specified and directed by Engg-In-Charge

Cleaning the surface with wire brush,detecting sources of lea and removing/taking down unsound treatment/surface,proving material and labour for carrying out non-destructive water proofing treatment to sunken portion of slab,floor and walls of bath,WC,WHB and floor trap (combined unit) by using construction chemical method as hydrophobic PU grouting etc with first course of injection MDI based PU foam and second course of injection PU plain all as manufacturers instruction,etc,the PU foam shall have 100% solids and solvent free,and shall expand 30-40 times its volume at liquid stage in presence of water,the PU plain injection shall have minimum 100CPS visscosity and shore hardness minimum 50 complete all as specified and directed.Make:PIDILITE or equivalent

M&L for fixing the metallic packer for hydrophobic PU foam including making holes and sealer all as per manufacturers specification,the PU foam shall have 100 % solids and solvent free,and shall expand 30-40 times its volume at liquid stage in presence of water,the PU plain injection shall have minimum 100CPS visscosity and shore hardness minimum 50 complete all as specified and directed. Make: PIDILITE or equivalent. Note:This item is catered only for Material and labour by for fixing the metallic packer

M&L for the chemical cleaning of tile joints and re-grouting carefully by washing the existing tile with heavy duty tile cleaner preferably of M/S Pidilite or equivalent cleaner,again washing with fresh jet water,scratching the joints and filling the same with (white/matching colour) epoxy tile grout of M/S Pidilite,ROOF RTM epoxy or euivalent,curing,cleaning the surface etc as per the sample done at site complete all as specified and as directed.

M&L for false ceiling with vinyle faced Arn-GYP-FB, celing 600 x 600 x 7-8 mm thick with washable metallized polyster foil backing with vinyle covered edges supporting sections shall be of sutable size from same makes embossed on section and level adjuster duly suspended by 2mm dia GI wire fixed to roof at 600mm center to center as per manufactureres instruction and including taking down all as directed. Make : Armstrong or equivalent in Saint Gobin/Lafarge

Supply and fix in repair health faucet (hand shower) with 8 mm dia 1 m long flexible tube wall mounted / hooked all as per

Supply and fix in repair bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule all as directed.

Supply and fixing in repairs stop valve cast copper alloy, fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore

Supply and fix in repair 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

Supply and fix in repairs, shower rose with shower arm

Supply and fix 15 mm dia pillar tap(Swine neck), cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

Hacking out old broken glass (any thickness size,quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads n'exc 1.5 Sqm.

Material and labour for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane all as directed.

Supply and fix in repair galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples all as directed.

Supply and fix in repairs rotational moulded polyethylene water storage tanks Tripal layer (cylindrical vertical with closed top) of 500 litres capacity hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to irin pipr and connecting complete all as specified and directed.

-ditto-- all as per Sr item No 94 above but 1000 ltrs etc.

S&F in repairs PVC connections 15 mm size with Stainless steel Nuts of length 600mm

S&F in repair for stainless steel grating without waste holes 100 mm dia

S&F in repair for stainless steel grating with waste holes 100 mm dia

S&F for PVC (SWR) floor trap, plain with grating including jointing with solevent cement 75 mm bore

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all as per Sr item No 100 above but as in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all as per Sr item No 102 above but as in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore

S&F PVC (SWR) vent cowl110mm bore

S&F for low density polyethelene pipes 32 mm bore (LDPE) of pressure rating 6 Kg/cm² laid in trenches/fixed to wall

Supply and fix repairs 10 L PVC valveless, syphonic action type, flushing cistern,low level, all accesories all as directed. Make :- Sleek essence series Of Hindware or Cat part No E8303 Of Parryware .

Taking up or down steel tubing and connections,15 mm bore

-ditto-- all as per Sr item No 112 above but 20mm bore

S&L of CPVC pipes SDR 11 including fittings in trenches, 16mm outer dia fixed to walls /ceiling or laid in trenches incl all necessary fittings.

--ditto-- all as per Sr item No 114 above but 20mm outer dia etc

Cutting chases, pinning in makding good to facing where required and pointing in cment morter 1:3 for consealed water tubing cutting not exc 10 cm girth

Supply and fix coloured anodised aluminium three track window made out of Jindal aluminium sections Nos 20671,20672,20690 & 20668 including 5 mm thick plaint sheet glass and stainless steel wire guaze as per PS, locking arrangement all as directed.

S&F coloured anodised aluminium ventilator as per PS and make approved by GE including all fittings locking arragement, glazing, guazing and fixed with suitable size of screws all as directed

Fixing only for framed work such as guard bars/ grill /gratings etc with ends of bars shouldered and/or riveted or gorged into spikes confroming to FE-290, Gde -E- 165

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in the same opening including easing and adjusting and also refixing builders hardware as required including renewal of unservieable screws etc

S&F in repair for 19/20mm PVC shutter Colour PVC prelaminated board fixed to timber frame worka as in cup boards shutters/shelves/pelmets box and similar items etc complte all as specified and directed by Engineer-in-Charge

S&F for in repairs auto closing hinges 35mm of o crank (KH-001) or 8 crank (KH=002) openable at 110 degree for kitchen cabinet shutters fixed complete as specified and directed

Supply and fix in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets etc complete all as specified and directed by Engineer-in-Charge

Supply and fix repairs PVC (SWR) floor trap, 75 mm dia with grating including jointing with slovent cement etc all as directed.

S&F in repair Brass Chromium Plated toilet paper holder fixed with (CP) brass screws of approved quality.

S&F in repairs PVC Seat Cover with hinges complete all as specified.

S&F in repairs decorative towel ring recangular chromium plated fixed with (CP) brass screws of approved qualityas specified

S&F in Soap Dish wired type including necessary fitting material screws etc complete all as specified.

S&F in repairs looking mirror of size 600 mm X 450 mm etc complete all as specified and directed by Engineer-in-charge.

S&F in repairs corner glass shelf 200mm size

S&F in repair 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s. /25mm-455gms/ 40mm - 690 gms) complete al as directed.

S&F in repair 25mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s. /25mm-455gms/ 40mm - 690 gms) complete al as directed.

M & L for providing water proofing treatment on roofs, as per manufacturere's instructions and as specified after taking down/out as existing out at site etc complete all as specified and directed by Engineer-in-Charge (a) Cleaning the newly plasterd surfaces with wire brushes and applying a bituminous primer @ 0.30 l/sqm & surface shall be allowed to dry. (b) Applying and laying torch APP polymer modifiedbituminous membrance 3mm thick with non woven polyster matt as reinforced weighing not less than 3 kg/sqmts by therofusion process as per manufacturers specification including applying one coat of aluminium paint Make : Super Thermolay of STP or equivalent in TEXSA India Ltd / IWL Ltd / Tiki Tech

M&L for plastering 10 mm in cement and sand mortar (1:3) using 100 % course sand on roof mied with and including WPC @ 3% by weight of cement and finished the surface even and smooth without using extra cement.

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Chage

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories PVC boxes (upto 18 module suitble for Mylinc series of Legrand including white plates with frame upto 18 module of make suitable for Mylinc Series ) for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2.Wiring shall be done as per complaints recd from user only on required basis it is not necessary to do whole wiring of any whole bldg 3. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc

One light point/fan/bell point controlled by switch 5 Amp single pole one way

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

--ditto-- all as per Sr Item No 136 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S&F switch piano flush type single pole, one way 5/6 Amp etc complete all as specified and directed by Engineer-in-Charge

S&F bell push piano flush, single pole, one way 5/6 Amp etc complete all as specified and directed by Engineer-in-Charge

S&F bell ding dong elelctric 230V AC single pole etc complete all as specified and directed by Engineer-in-Charge

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required etc complete all as specified and directed by Engineer-in-Charge.

S & F electronic dimmers,as per existing wattage, 250V flush type on the exiting phenolic laminated sheet etc. as required etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Switch, 6 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Switch, 6 Amp, two way, one Module. etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Switch, 16 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Socket Outlet 6 Amp, 3 pin, combined two module etc complete all as specified and directed by Engineer-in-Charge.

S&F Modular Socket Outlet 6 Amp / 16 Amp - 2/3 pin combined two module complete all as specified and directed by Engineer-in-Charge

S&F Modular Bell push, 6 Amp, one module etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

M&L ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge

S&F Socket outlet 3 Pin ,6 A etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement double door Sheet metal enclosures factory made DBs 4 way SPN, 240 volts ,Concealed in wall protection class IP-42, suitable for fixing of MCBs, Isolators etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed. Make: Legrand / Simens/ L&T/Havells

Supply & fixing MCB , SP, AC, 240 Volts of 06 to 32 Amp capacity 16KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, TPN, AC, 415 volts of 63 Amps capacity 10 KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, SPN, AC, 240 volts of 40 Amps capacity 10 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, SPN, AC, 240 volts of 63 Amps capacity 10 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Taking out old PVC/Wooden/metal switch board ,wire connection from the wall and fix new PVC Modular box including connecting wire suitable for fixing switch/Socket/fan regulater of following sizes. (Note. Damaged Switch/Socket/regulator will be measured and paid Sepereately)

Supply and fix square profile LED lighting fixture, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 22 Watt aluminium housing with LED light source 6500 K,input voltage 140V-270V with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge Make: Phillips Smart bright batten or equvalent in other Make .

S&F square profile LED lighting fixture, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 12 Watt input voltage 140V-270 V with LED light source 6500 K with uniform light output, with all accessories including its connection with 2 core seathed cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge.Make: Phillips Smart bright batten or equvalent in other Make .

S&F environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head Back-lit 10 W LED ,IP65 ,IK 08 rated product luminaire comprising of high brightness LEDs complete with all accessories prewired and including connecting up with & including twin core twisted flexible copper conductor cable of suitable size etc complete all as specified and directed by Engineer-in-Charge

Supply & fix replacemnt industrial type switch socket for Geysers with 20 Amp MCB etc complete all as specified and directed by Engineer-in-Charge

S&F sub main wiring with two single core PVC insulated,unsheathed, FRLS stranded copper conductor cable 4 Sqmm with 4 Sqmm PVC insulated, unsheathed, FRLS stranded copper conductor cable as earth wire drawn through and including PVC Casing and capping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge Note : 1. Porper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. Two run of 4 Sqmm cable i.e for one run for phase, one run for neutral with one run of 4 Sqmm cable for earth and one run of PVC Casing & caping shall be measured as one unit.

Taking out/down carefully and opening of existing water Geysers of 25 Ltrs capacity,from any position, of any make etc & refixing after reassembling and after repair /replacement of spare parts/ material/items ( such as outer and inner tank) at the desired location and making necessary water inlet, outlet & electric connections to make it functional with including using material/parts of minor nature such as screws, insulation tape, nuts, bolts, washers etc including cleaning to required gloss with white synthetic enamel paint on complete body & writing MES No with black synthetic enamel paint etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement heating element 2 KW, rubber gasket type with & including rubber gasket complete suitable for 25 Ltrs Geysers of any Make as installed at site etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement PVC insulated cable 40/0.0076, 3 core copper conductor cable for connection from geyser to top plug etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement indicator lamps(set of two -green & red) AC, 220 volts suitable for 25/50 ltrs capacity vertical type geyser etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement thermostat switch , pointer type with adjustable knob, suitable for 25/50 ltrs capacity vertical type geyser & etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix PVC connection pipe for Geysers complete with brass end terminal size 300 mm long etc complete all as specified and directed by Engineer-in-Charge

Supply and fix PVC connection pipe for geysers complete with brass end terminal size 450 mm long etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement thermal cut out suitable for 25/50 ltrs capacity vertical type geyser etc complete all as specified and directed by Engineer-in-Charge.

Taking out/down existing ceiling fans upto 1400 mm sweep,from any position, of any make etc and handover to user to deposit E/M Store yard & refixing Serviceable fan at the desired location making electric connection by replacing PVC insulated unsheathed cable of copper conductor of size 1.50 Sqmm upto 0.50 Mtr length with & including using material/parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/lubricant etc to make it functional etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement capacitor 2.5 mfd, 250 volts , AC etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of rubber reel, bolt, nut including pin etc complete all as specified and directed by Engineer-in-Charge.

Supply only conopy (top and bottom) of ceiling fan , of any sweep, any make etc complete all as specified and directed by Engineer-in-Charge.

S & F for modular plates white colour with frame of 3 module including removal of old unserviceable one complete complete all as specified and as directed

S & F for modular plates white colour with frame of 6 module including removal of old unserviceable one complete complete all as specified and as directed

S & F for modular plates white colour with frame of 10/12 module including removal of old unserviceable one complete complete all as specified and as directed

S&F in replacement Modular metal flush box 6 Module complete all as specified and directed

S & F for plastic body exhaust fan, AC single phase, 240 V of size 150 mm sweep including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed.

S & F for plastic body exhaust fan, AC single phase, 240 V of size 200 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed

S & F blank plates round/square in wall for fixing Ceiling roses,etc as specified and as directed

Preparing the old painted surfaces of following steel furniture by removing old paint & touching up with Red oxide primer where necessary & denting where necessary & preparing the surfaces & spray / mannualy painting with two coat of synthetic enamel paint as per existing colour of articles all as specified & directed. NOTE : Spray painting shall be carried out mechanically.

Almirah med steel W/S

Almirah large steel W/S

Book Case steel (Glass door)

Chair steel W/O arms

Chair CB Steel W/Arm

Teapoy varandah

Charpoy IP Steel Hardtop

Table 900 x 600 W/O drawer

Table 900 x 600 with drawer

Chair Varandah

Shoe Rack Steel

Bed Hard Steel

M&L One coat of french polish on wooden surface of any width or girth incl scrapping and cleaning all as per drg and as directed by Engineer-in-charge. Polishing to following wooden furniture items shall be carried out in occupied quarters.

Almirah large with shelves

Almirah medium 1/2H 1/2SH

Almirah medium with shelves

Bed with plywood top

Book shelf open large

Book case small

Book case various type

Chair Easy

Chair Dinning cushioned

Chair writing

Chair Dinning

Hat stand W/M

Peg Table

Table bed side w/o drawer

Teble centre (FD)

Table Dinning 6 persons

Table dressing ladies W/M

Table dressing gents W/M

Teapoy FD

Table writing

Chair tipup wooden

Table 3' x 2' W/O drawer

Table 3' x 2' with drawer

Table Dining 04 Person

Table Dining 08 Person

Sofa Set 05 Seater

Sofa Set 04 Seater

Day to day complaints for the following works :-

(a) Complaint related to carpenter works like door easing, door repair, kitchen cup board repair, window/door wire mesh/glass pane repair, refixing of building hardware etc by deploying carpentor and mazdoor.

(b) Complaint related to plumbing works like repair/refixing of Bib tap, Stop cock, Angle cock Connection pipes, waste pipes, Flush tank, Flush pipe,Shower, Pvc tank, ball valves, towel rail ,WHB,EWC, waste coupling, Grating,Pillar tap etc.by deploying plumber and mazdoor.

(c) Complaint related to cement works like repair to floors/ wall plaster in patches/ filling of holes, tiles repairs etc. by deploying mason and mazdoor.

(d) Removing blockage from water closet,floor or gully or Nahani trap and bends by rodding thoroughly and pouring water under pressure and cleaning,clearing the drainage to efficient and smooth flow of sludge/waste water all as specified and directed by Engg-in-charge.

(e) Cleaning of blocked sewage line of the dia 75 mm to 300 by using bamboo sticks or MS rods and revolving with rope or with sludge sunction /pumping machine inside the sewer line between two manholes and cleaning the sewer line and pouring water under pressure and cleaning and clearing sewer line to efficient and smooth flow of sludge/waste water .

Notes for Ser item Nos 232 to 236 :-The quoted rate of contractor shall comprise the following :-

Note:- (i) Contractor will establish a well furnished complaint cell to recieve the complaints (Petty repair) in the md accn as per location allocated by Enginner-in-Charge/GE. (ii) Contractor will deploy a Data Entry operator staff to recieve the complaints made by users in complaint cell from time 9:00 AM to 17:00 PM on all working day. (iii) Contractor will deploy sufficient plumber/ Carpentor/ Mason/ safaiwala/ electrician to attned the daily complaints (petty repair) on daily basis. Attendance report of the deployed skilled staff alongwith their healper will be submiited to JE/Engineer-in-Charge on daily basis. (iv) Contractor's supervisor will report on all working days alongwith their skilled staff and printed contractor's firm name complaint slip book at 8:30 hrs at JE/Engineer-in-Charge received complaints from users and to submit completion report/constraints, if any on the same day by 1700 hrs. (v) Printed complaint slip book as per format approved by Engineer-in-charge shall be provided and maintained by the contractor. (vi) If there is any major complaints of tilling/Plumbing/Joinery/ electrician/BS for which additional times/manpowers or T&P as required the same shall be provided by the contractor without any extra cost to Govt. The same will be reoprted to JE/Engineer-in-Charge for taking consent. (vii) If the complaints will not be attended a recovery @ Rs. 1000 per day shall be recovered from the amount due to the contracor.

(viii) Store for attending the complaints will be provided by the contractor on daily basis. (ix) Rate quoted in above BOQ shall be deemed to incl the cost of office staff/ office equipment, required T&P/stores and device etc alongwith sufficinet skilled manpowers/ labour to attend/complete the complaints in the same day duly signed by users at the entire satisfaction of Engineer-in Charge. (xii) Access will be given to contractors rep to the mobile application developed by Dept to monitor the complaints.

DHANANJAY BABAN KALANE (BID ID -3175753)

MATOSHREE CONSTRUCTION (BID ID -3176070)

Avinash B Kullal (BID ID -3176207)

Maruti Abhiyantriki (BID ID -3175876)

M/s AG PATHAN (BID ID -3175749)

M/S. YADAV ENTERPRISES (BID ID -3176426)

Arihant Construction (BID ID -3175157)

M/S. M. F. Sharif & Co. (BID ID -3175962)