REPAIR MAINT OF FIRE FIGHTING PIPELINE FIRE HYDRANTS SWT PIPELINE AND REPAIRS TO VARIOUS TYPE OF PUMPS WITH ALLIED WORKS AT PH I AND PH II AREA UNDER GE NARANGI

Amount

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation, laying of pipe or for shafts, wells cesspits,man holes etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling, in including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick complete all as specified and as directed.

Removing excavated soil to distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed.

Supplying, laying & testing 250 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

Supplying, laying & testing 200 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

Supplying, laying & testing 150 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

Supplying, laying & testing 100 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

Cutting CI/DI pipes of 250mm bore and reducing to required length before laying in position for insertion of new tee, branches etc complete all as specified and as directed.

Cutting CI/DI pipes of 200mm bore and reducing to required length before laying in position for insertion of new tee, branches etc complete all as specified and as directed.

Cutting CI/DI pipes of 150mm bore and reducing to required length before laying in position for insertion of new tee, branches etc complete all as specified and as directed.

Cutting CI/DI pipes of 100mm bore and reducing to required length before laying in position for insertion of new tee, branches etc complete all as specified and as directed.

S&F Rubber or fibre board gaskets for flanged joints of size 250mm dia pipe complete all as specified and as directed.

S&F Rubber or fibre board gaskets for flanged joints of size 200mm dia pipe complete all as specified and as directed.

M&L for Ductile iron (DI) fittings 100 mm to 450 mm bore for spigot and socketed pipes such as bends (any type radius and angle), tappers any type (straight, bend, increasing, decreasing or double socket type etc), tee pieces, single branch, Y junction, double branch, cross (all sockets or socket and spigot etc), collars, caps & plugs etc. conforming to IS 9523 complete all as specified and as directed.

M&L for construction of brick masonry valve pit of size 90 cmx 90 cm x 90 cm (internal dimension) one brick thick wall built in CM (1:4) on 100mm thick PCC (1:4:8) type D2, (nominal mix) as in foundation, and 15mm thick rendering in cement mortar (1:4) both externally and internally, external plaster shall be up to 15cm below GL, providing valve pit cover made of 3.15mm thick MS sheet/plate, including provision of hinges, handle and locking arrangement including40X40X 6mm angle iron frame fixed on top of valve pit by means of MS hold fast 40x6mm and 150mm long, embedded in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) block of size 230X200X100mm, including two coats of anti-corrosive paint over a coat of red oxide zinc Chrome primer and necessary earth work in soft/loose soil including demolition of old valve pit complete all as specified & directed.

M&L for construction of brick masonry valve pit of size 60 cmx 60 cm x 60 cm (internal dimension) one brick thick wall built in CM (1:4) on 100mm thick PCC (1:4:8) type D2, (nominal mix) as in foundation, and 15mm thick rendering in cement mortar (1:4) both externally and internally, external plaster shall be up to 15cm below GL, providing valve pit cover made of 3.15mm thick MS sheet/plate, including provision of hinges, handle and locking arrangement including40X40X 6mm angle iron frame fixed on top of valve pit by means of MS hold fast 40x6mm and 150mm long, embedded in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) block of size 230X200X100mm, including two coats of anti-corrosive paint over a coat of red oxide zinc Chrome primer and necessary earth work in soft/loose soil including demolition of old valve pitcomplete all as specified & directed.

S&F in repairs, sluice valve (heavy duty) with heavy duty stainless steel spindle conforming to IS 14846 (2000) both end flanged class PN 1.6 of size 250 mm dia including necessary nuts,bolts washers and gasket complete all as specified and as directed.

S&F in repairs, sluice valve (heavy duty) with heavy duty stainless steel spindle conforming to IS 14846 (2000) both end flanged class PN 1.6 of size 200 mm dia including necessary nuts,bolts washers and gasket complete all as specified and as directed.

S&F in repairs, sluice valve (heavy duty) with heavy duty stainless steel spindle conforming to IS 14846 (2000) both end flanged class PN 1.6 of size 150 mm dia including necessary nuts,bolts washers and gasket complete all as specified and as directed.

M&L for complete servicing, greasing of the Fire fighting pump motor sets of capacity 120 HP/ 105 BHP by dismantling from position, unscrewing nut bolt, cleaning, greasing and replacement of unserviceable bushes, Shaft Sleeve, bearing, gasket, gland packing / water seals, nut bolts of suitable size and re-assembling the same in existing position including two coats of synthetic enamel paint over a coat of red oxide primer and connecting to both end terminal circuit, commissioning and testing on full load condition complete all as specified and as directed. (Make of Bearing: SKF/ TATA) (Note:- (i)Necessary arrangement of T&P items required for the job shall be deemend to be included in the quoted rate. (ii). Cost of new bushes, bearing, gasket, gland packing nut bolts etc shall be deemened to be included in the quoated rate.)

M&L for complete servicing, greasing of the Fire fighting pump motor sets of capacity 100 HP by dismantling from position, unscrewing nut bolt, cleaning, greasing and replacement of unserviceable bushes, Shaft Sleeve, bearing, gasket, gland packing / water seals, nut bolts of suitable size and re-assembling the same in existing position including two coats of synthetic enamel paint over a coat of red oxide primer and connecting to the both end terminal circuit, commissioning and testing on full load condition complete all as specified and as directed. (Make of Bearing: SKF/ TATA) (Note:- 1. Necessay arrangement of T&P items required for for the job shall be deemend to be included in the quoted rate. 2. Cost of new bushes, bearing, gasket, gland packing nut bolts etc shall be deemened to be included in the quoated rate.)

M&L for complete servicing, greasing of the Fire fighting pump motor sets of capacity 40 HP/ 50 HP by dismantling from the position, unscrewing nut bolt, cleaning, greasing and replacement of unserviceable bushes, Shaft Sleeve, bearing, gasket, gland packing / water seals, nut bolts of suitable size and re-assembling the same in existing position including two coats of synthetic enamel paint over a coat of red oxide primer and connecting to the both end terminal circuit, commissioning and testing on full load condition complete all as specified and as directed. (Make of Bearing: SKF/ TATA) (Note:- 1. Arrangement of necessary T&P items required for dismantaling and reassembling pump motor set shall be deemend to be included in the quoted rate. 2. Cost of new bushes, bearing, gasket, gland packing nut bolts etc shall be deemened to be included in the quoated rate.)

M&L for complete servicing, greasing of the Fire fighting pump motor sets of capacity 25 HP by dismantling from the position, unscrewing nut bolt, cleaning, greasing and replacement of unserviceable bushes, Shaft Sleeve, bearing, gasket, gland packing / water seals, nut bolts of suitable size and re-assembling the same in existing position including two coats of synthetic enamel paint over a coat of red oxide primer and connecting to the both end terminal circuit, commissioning and testing on full load condition complete all as specified and as directed. (Make of Bearing: SKF/ TATA) (Note:- (i) Arrangement of necessary T&P items required for dismantaling and reassembling pump motor set shall be deemend to be included in the quoted rate. (ii). Cost of new bushes, bearing, gasket, gland packing nut bolts etc shall be deemened to be included in the quoated rate.)

M&L for complete servicing, greasing of the Fire fighting pump motor sets of capacity 12.50 HP/ 10 HP by dismantling from the position, unscrewing nut bolt, cleaning, greasing and replacement of unserviceable bushes, Shaft Sleeve, bearing, gasket, gland packing / water seals, nut bolts of suitable size and re-assembling the same in existing position including two coats of synthetic enamel paint over a coat of red oxide primer and connecting to the both end terminal circuit, commissioning and testing on full load condition complete all as specified and as directed. (Make of Bearing: SKF/ TATA) (Note:- (i). Necessary Arrangement of T&P items required for dismantaling and reassembling pump motor set shall be deemend to be included in the quoted rate. (ii). Cost of new bushes, bearing, gasket, gland packing nut bolts etc shall be deemened to be included in the quoated rate.)

M&L for complete servicing, greasing of the Fire fighting pump motor sets of capacity 3 HP/ 5 HP/ 7.50 HP by dismantling from the position, unscrewing nut bolt, cleaning, greasing and replacement of unserviceable bushes, Shaft Sleeve, bearing, gasket, gland packing / water seals, nut bolts of suitable size and re-assembling the same in existing position including two coats of synthetic enamel paint over a coat of red oxide primer and connecting to the both end terminal circuit, commissioning and testing on full load condition complete all as specified and as directed. (Make of Bearing: SKF/ TATA) (Note:- 1. Arrangement of necessary T&P items required for dismantaling and reassembling pump motor set shall be deemend to be included in the quoted rate. 2. Cost of new bushes, bearing, gasket, gland packing nut bolts etc shall be deemened to be included in the quoated rate.)

M&L for disconnecting 100 HP Centrifugal motor from the pump, taking out burnt winding wire of field coil and re-winding of field coil with suitable size of super enameled copper winding wire with necessary insulating materials including complete overhauling and refixing motor, pump on frame with new nuts, bolts, washer etc. and necessary connection to the terminal and testing on full load condition complete all as specified and as directed.

M&L for disconnecting 40 HP Centrifugal motor from the pump, taking out burnt winding wire of field coil and re-winding of field coil with suitable size of super enameled copper winding wire with necessary insulating materials including complete overhauling and refixing motor, pump on frame with new nuts, bolts, washer etc. and necessary connection to the terminal and testing on full load condition complete all as specified and as directed.

M&L for disconnecting 25 HP Centrifugal motor from the pump, taking out burnt winding wire of field coil and re-winding of field coil with suitable size of super enameled copper winding wire with necessary insulating materials including complete overhauling and refixing motor, pump on frame with new nuts, bolts, washer etc. and necessary connection to the terminal and testing on full load condition complete all as specified and as directed.

M&L for disconnecting 12.50 HP/ 10 HP Centrifugal motor from the pump, taking out burnt winding wire of field coil and re-winding of field coil with suitable size of super enameled copper winding wire with necessary insulating materials including complete overhauling and refixing motor, pump on frame with new nuts, bolts, washer etc. and necessary connection to the terminal and testing on full load condition complete all as specified and as directed.

M&L for lifting of submersible non clogging pumpset with 12.5 HP/ 10 HP capacity motor from sewage well for repair/ rewinding, after taking out burnt winding wire and re-winding with suitable size of super enameled copper winding wire with necessary insulating materials and re-installing the same by proper assembling and connected with pumpset, commissioning and testing with full load condition complete all as specified and as directed.

Rana Kr Phookan

M/s JK Jangid and Company

M/S SR BUILDERS