ADDITION / ALTERATION AND SPECIAL REPAIRS TO MD ACCN BLOCK NO. B-15 TO B-19 (56 QTRS), C-11 TO C-15 (80 QTRS) AND D-08 TO D-11 (48 QTRS) IN DRDO TOWNSHIP, PHASE-I, CV RAMAN NAGAR, BANGALORE

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n.exc 1.50 sqm each all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm but n.exc 4sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each.

Taking down Shutters of any description n.exc 1 sq. m each.

Cutting chases pinning in making good for brick walls to facing where required and pointing in cement mortor 1:3 to ends or edges of concealed water tubing and similar work including making good cutting not exc 10CM girth complete all as specified and directed.

Taking down boards of any description and any size as in shelves complete all as specified and directed.

Taking down, easing, adjusting and refixing builders hardware as required including renewal of unserviceable screws etc, and refixing in the same opening after laying of tiles, shutters of any description exceeding 1.0 sq.m but not exceeding 2.0 sq.m each, complete all as specified and directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, including making good to jambs with cement mortar 1:4 and finished to match with existing surface complete all as specified and directed.

Factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck in side with solvent cement for stiles and plain colour PVC sheets for top rails and bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in MS frame welded / sealed to the stiles, rails with suitable PVC sheet beading and joined to gether with solvent cement supplying & fixing in the frame at site complete all as specified and directed.

Pressed steel frames of size 105 x 60mm x 1.25 mm thick for door with one or more rebates, including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

Pressed steel frames of size 125 x 60mm x 1.25 mm thick for door with one or more rebates, including necessary fixing lugs, hinges, lock strike plate, Single action spring hinges etc complete all as specified and directed.

PCC 1:3:6 type C0 using 12.5mm graded stone aggregated as in filling the chowkats / frames complete all as specified and directed.

35 mm thick plain, framed, panelled factory made shutters with IInd class hardwood rail and style with lock rail and panel of 9 mm BWP commercial ply with commercial vaneer on both faces. The size of rail and style as per IS-1003 Part-I complete all as specified and directed.

35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, both face is covered with decorative face veneer with lipping / frame to match all as specifed and directed. Note: The rates for flush shutters include for the provision of suitable blocks for fixing mortice locks, latches, or other fittings.

35mm thick IInd class hardwood glazed and skeleton shutters open rebated and prepared to receive gauge (without sash bars) edges of framing plain, chamfered or round fitted with cut and mitred beads for securing wire gauge sizes of members of shutters all as specified and directed.

18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw to timber frame work, shelves of cupboard & door etc, all as specified and directed.

M&L for PVC lipping fixed to prelaminated particle board to match with color of board and width etc, complete all as specified and directed.

18/19 Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one side and other side balancing white face; fixed with screws to timber frame work, shelves of cupboard & door etc, all as specified and directed.

All as per Sl item No. 18 above but 12mm thick.

All as per Sl item No. 18 above but 09mm thick.

Fancy type stainless steel handle of size 100 mm long complete all as specified and directed.

Magnetic ball catches of standard type fixed complete all as specified and directed.

Continuous (piano) hinges, stainless steel, bright finish or electrogalvanised with width of flaps (when open) 40 mm.

Aluminium channel for double track 18mm thick sliding shutter including required wheels and necessary fittings all specified and directed.

Aluminium anodised barrel tower bolts of extruded section, 150 mm long all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section, 150 mm long fixed in repairs all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section, 100 mm long all as specified and directed.

150mm long extruded aluminium alloy handles, fabricated type anodised all as specified and directed.

150mm long extruded aluminium alloy handles, fabricated type anodised fixed in repairs all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple bolt type and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple bolt type and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long fixed in repairs all as specified and directed.

100 mm size hasp and staple, safety type, aluminium anodised, including bolt to hinge plate and fixed with screws, complete all as directed.

Door stopper of rubber and aluminium alloy body, 150 mm size fixed in repairs all as specified and directed.

Door stopper of rubber and aluminium alloy body, 150 mm size all as specified and directed.

Mortice lock, (six lever) vertical type mild steel of 100mm size including handle, screwing and fixed in repairs all as specified and directed.

Magic eye fixed to wooden door shutter complete all as specified and directed.

SS butt hinges medium weight of size 100 mm complete all as specified and directed.

Mild steel butt hinges medium weight cold rolled of size 100 mm including necessary welding fixed in repairs complete all as specified and directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified.

Dismantling of composite steel windows / ventilators not exceeding 0.60 Sqm single leaf double shutter with fixed portion including taking down glass panes and mosquito proof mesh but except grill / guard bars in any position complete all as specified and directed (ONLY SHUTTER DISMANTLING).

Dismantling of composite steel windows / ventilators exceeding 0.60 Sqm but not exceeding 1.80 Sqm double / triple leaf double shutter with fixed portion including taking down glass panes and mosquito proof mesh but except grill / guard bars in any position complete all as specified and directed (ONLY SHUTTER DISMANTLING).

Powder coated aluminium frame for windows, ventilators with one or more rebates (3 Track sliding window) including joining cleat for fixing, rubber neoprene packing for fixing, including minor fitting like lock, handle, roller for sliding etc. complete all as specified. Note: (i) For payment purpose, only weight of aluminium section shall be measured and paid, however cost of aluminum mongry, lock, rubber packing, roller for sliding shall be deemed to be included in the quoted rate. (ii) The height of buildings is upto 16m, necessary cost of scaffolding shall be deemed to be included in the quoted rate.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilatorsincluding providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. Note: (i) For payment purpose, only weight of aluminium section shall be measured and paid, however cost of aluminum mongry, lock, rubber packing, roller for sliding shall be deemed to be included in the quoted rate. (ii) Sheet glass and wire gauge shall be measured and paid separately. (iii) The height of buildings is upto 16m, necessary cost of scaffolding shall be deemed to be included in the quoted rate.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed.

4mm thick sheet glass ordinary quality and glazing with rubber beading and necessary clips in squares exc. 0.5 Sqm in each pane complete all as specified and directed.

4mm thick pin head glass and glazing with rubber beading and necessary clips, in square n exc. 0.5 Sqm in each pane complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed in repairs all as specified and directed.

Tubular curtain rail, stainless steel anodized 20 mm dia all as specified & as directed including taking down unserviceable rod / rail complete all as specified and directed.

Stainless aluminiuml type brackets suitable to hold the curtain rod with sofio phenol (Lotto) and wooden round blocks suitable to curtain rod of 20mm dia, decorative type fixed with suitable steel screws and PVC cleats, including taking down unservicable brackets complete all as specified and directed.

Taking up or down 15mm dia GI tubing surface / concealed laid in wall / floor / ceiling complete all as specified and directed.

Taking up or down 20mm dia GI tubing surface / concealed laid in wall / floor / ceiling complete all as specified and directed.

Supplying & fixing of 20mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 with all fittings fixed on walls / ceiling or laying in floors complete all as specified. Note: The quoted rate shall include for all fittings, like brass elbow, brass tees, male brass threaded adaptor, female brass threaded adaptor etc.

GI tubing medium grade with all fitting fixed to wall / ceiling or laid on floor complete of size 20mm bore all as specified and directed.

Refixing of old GI tube 20mm bore water tubing surface / concealed in same / new location after cleaning and application of bituminous paint on concealed portion of tubing including cutting & threading pipe and provision of additional fittings such as socket, tee, elbow, union (if required) complete all as specified and directed. Note: i) Taps, valves if any shall be removed before taking down pipe. ii) Cutting chases and making good shall be measured and paid separately.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, UPVC (SWR) pipes 110 mm dia, type B (conforming to IS 13592) single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, UPVC (SWR) pipes 75 mm dia, type B (conforming to IS 13592) single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and directed. Note for Sl item No. 56 & 57: Provision of necessary scaffolding for replacing defective pipes shall deemed to be included in quoted rates and nothing extra will be admissible in this regards.

PVC (SWR) bend 75 mm dia with access door complete all as specified and directed.

PVC (SWR) junction single 'T' equal or unequal 75 mm bore with access door complete all as specified and directed.

PVC (SWR) junction single 'T' equal or unequal 110 mm bore with access door complete all as specified and directed.

PVC (SWR) pipe, 40mm dia including necessary connectors, bends, Tee etc conforming to IS:4985-2000 fixed with solvent cement joints, laid on floor or on walls, fixed as drain pipe in wash hand basin, spount pipes in balconies etc., including taking down old unserviceable pipes, complete all as specified and directed.

Cutting holes n. exc. 150 sq. cm into or through in brick walls built, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed.

PVC (SWR) multi-floor trap, plain with chromium plated grating including jointing with solvent cement, 75mm dia, including dismantling the damaged trap, complete all as specified and directed.

PVC (SWR) floor trap with and including, plain / single hole chromium plated grating including jointing to waste pipe with solvent cement, 75mm dia, complete all as specified and directed.

Dismantling water tanks from roof any description of 500 Ltr capacity complete all as specified and directed.

Disconnecting existing PVC water tank of 500 Ltrs capacity setting aside (or lowering if required) for repairs, cleaning, etc, and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Rotational moulded polyethylene water storage tanks (triple layered) of 500 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball scrured for iron pipe of dia 20 mm bore complete all as specified and directed.

Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball scrured for iron pipe of dia 20 mm bore as fixed in repairs complete all as specified and directed.

Gun metal Gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed including cutting the old pipes as in repairs complete all as specified and directed.

PVC (SWR) vent cowl of bore 110 mm dia, including taking down old PVC vent cowl all as specified and directed.

PVC (SWR) gully traps square or round mouthed type 'P' of size 150 x 150 mm including taking down connecting to existing line and provision of PCC bedding complete all as specified and directed.

Vitreous china, white colour, water closet pan (pedestal pattern), with PP soft seat cover, hinges, other fixing accessories set (excluding flushing cistern and flush pipe), UPVC (SWR), 'P' or 'S' trap, and connecting to drain (or outgoing pipe), flush pipe, anti syphonic pipes, including removing debris outside MD land complete fixed in repairs all as specified and directed. Make: Cat Part No. S1050101 of Cera or techno commercially equivalent in other makes.

Vitreous china, white colour, 'Orissa pattern' squatting pan of size 580 mm x 440 mm with UPVC 'P' trap or 'S" Trap, front or back inlet, integral foot rests, connecting to trap, flushing pipe, anti syphonic pipe, including removing debris outside MD land fixed in repairs all as specified and directed. Make: Cera, Cat No. S3010102 of CALINA make or techno commercially equivalent in other makes specified.

PVC valve less, syphonic action type, white colour flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including jointing with new PVC long / short flush bend and making good to the disturbed surfaces complete fixed in repairs. Maake: Model No: CIENA PREMIUM Cat Part No. B1010102 of CERA Make or techno commercially equivalent in other makes.

Vitreous China wash basin, white, flat back, size 550 x 400mm excluding waste, chain and plug and porcelain stopper but including brackets, with inlet and outlet screwed for pipe or connections including 32mm CP waste coupling necessary packing, union and cap complete fixed in repairs all as specified and as directed.

32 mm dia, PVC waste pipe of length not less than 800 mm, complete fixed in repairs all as specified and directed.

Taking down and refixing of low level flushing cistern of any description and any capacity, complete all as specified and directed.

Stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen over all size 915 mm x 460 mm with bowl size 405 x 355 x 178 mm all as per Cat No. SSSBSD-52 of Blue Star make or techno commercially equivalent in other makes specified including CP waste coupling of 100 mm dia, cast iron cantilever brackets, 40 mm dia 800 mm long corrugated PVC waste pipe, washers, connecting union etc. including taking down old sinks complete fixed in repairs all as specified and directed.

Taking down and refixing of old kitchen sink of any description and any size, complete all as specified and directed.

CP waste coupling for kitchen sink of 40 mm dia (half or full threaded) including taking down old coupling of any description complete all as specified and as directed [Minimum weight for 40 mm-60 gms].

Stainless steel plate rack of 0.60mm thick sheet, size 787 x 914 x 254mm (31" x 36" x 10") complete all as specified and directed. Make: Blue star, Model No. SSKPR-315 or techno-commercially equivalent make of NIRALI / ANJALI / JAYNA / DIAMOND.

Two way, bib taps, fancy type, 15 mm dia, cast copper alloy, chromium plated, with CP flange, screwed for iron pipe or for brass ferrule fixed in repairs complete all as specified and directed. Make: Cat No. F280003 of Hindware or equivalent in other makes.

Bib taps 15 mm dia, fancy type, chromium plated with CP flange fixed in repairs all as specified and directed. Make: Cat No. F280002 of Hindware or equivalent in other makes.

Pillar taps, 15 mm dia, fancy type, chromium plated with CP flange, long shank fixed in repairs after taking down old pillar taps complete all as specified and directed. Make: Cat No. F280001 of Hindware or equivalent in other makes.

Angular stop cock, fancy type, with chromium plated wall flange, cast copper alloy, screwed both ends for iron pipe or for brass ferrule,15mm dia, complete fixed in repairs all as specified and directed. Make: Cat No. F280004 of Hindware or techno-commercially equivalent makes specified in list of makes.

Two way Angular stop cock, fancy type, with chromium plated wall flange, cast copper alloy, screwed both ends for iron pipe or for brass ferrule,15mm dia, complete fixed in repairs all as specified and directed. Make: Cat No. F570044c p of Hindware or techno-commercially equivalent makes.

15 mm CP stop valve (concealed type) cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union including taking down valve all as specified and directed.

Chromium Plated overhead shower rose of size 125 mm with swivel joints, over head shower arm of 200 mm long with wall flange, complete fixed in repairs all as specified and directed. Make: Hindware Cat Part No F160120 or techno-commercially equivalent makes specified in list of makes.

Single tube towel rail, brass chromium plated, 600 mm long fixed with chromium plated screws and PVC cleats, complete all as specified and directed. Make: CERA Model No. F5003103 or techno and commercial equivalent.

PVC connecting pipe 600mm long 15 mm dia both end having brass coupling nut and PVC washer fixed in repairs all as specified and directed.

Health faucet, with 8 mm dia, 1.2 m long, flexible tube in chrome finish, wall hook with NRV (back flow preventer), complete fixed in repairs all as specified and directed. Make: Cat Part No. F160023 of Hindware or techno commercially equivalent in other makes.

Chromium plated fancy type towel hook with three or Four arms hangers stainless steel complete all as specified and directed.

M&L for CP peg set (set of five) fancy type, complete all as specified and directed.

Brass chromium plated, fancy type, soap dish, as per Cat Part No. F450022 of Hindware or equivalent in other makes, and fixing with brass screws, complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. Make: Jaquar, Cat Part No ACN-CHR-1171N or equivalent in other makes.

Corner glass shelf (medium) 225mm x 225mm with chromium plated bracket superior quality complete all as specified and directed. Make: Cera, Cat Part No. F5005102 or techno and commercial equivalent in other makes.

PVC mirror cabinet of size 330 mm x 430 mm all as per Make: Prayag (Cat Part No. 551) or techno and commercial equivalent in other makes specified, complete after taking down old mirror cabinet all as specified and directed.

Chromium plated, 15mm bore dia of pipe Wall mixer with bend pipe for overhead shower, built-in non return valve with CP wall flanges fixed in repairs complete all as specified and as directed Make: Cat Part No. F280018 of Hindware or techno commercially equivalent in other makes.

Taking down existing chromium plated wall mixer of any type / description and refixing the same in same / new loacation after completion of all modificaion works with and including provision of necessary fixtures viz, CP flange plates, adjustable leg, CP nipple etc, as required, complete all as specified and directed.

Dismantling water tanks from roof exc 500 n.exc 1000 litres capacity complete all as specified and directed

Disconnecting existing PVC water tank of exc 500 & n.exc 1000 Ltrs capacity setting aside (or lowering if required) for repairs, cleaning, etc, and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Rotational moulded polyethylene water storage tanks (triple layered) of 750 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing from site and rubbish of the premises. Note: Demolition of traps / pipes if any is deemed to be included in the rates.

Demolition of Cement Concrete (un-reinforced) of any description and in any position not otherwise specifically provided for (as in sunken floors, coping, benching, padding, concrete tile on steps, etc.) and removing rubbish off the MD premises, complete all as specified and directed.

15 mm thick rendering in CM 1:3 on fair faces of brick work or concrete surfaces in sunken floors finished fair and even mixed with water proofing compound complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately under respective items.

Supply only liquid water proofing compound.

Providing 1.00mm thick BRUSHBOND RFX GREY (which is a two component acrylic polymer modified cementitious coating which shall consists of Brushbond RFX powder and Nitobond BBX acrylic emulsion), grey in colour of M/s FOSROC, applied using stiff brush, roller or trowel to obtain the desired thickness of plaster surface in sunken floor all as per manufacturers instructions, complete all as specified and directed.

PCC 1:5:10, type E2 (using 40 mm graded stone aggregate), in as mass concreet / sunken floors complete all as specified and directed.

Demolition of cement concrete in ground floor and paving n exc 15cm below or above ground level removing debris outside MD land complete all as specified.

75mm thick PCC type D2, (1:4:8) using 40mm graded stone aggregate as in sub base of paving / plinth, hard standing protection finishing rough complete all as specified and directed.

75 mm thick plain cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in paving / plinth protection laid in panels, finished even and fair.

PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) of 25 mm thick as in floor sub base finished even & smooth all as specified and directed.

PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) of 40 mm thick as in floor for garage finished even & smooth all as specified and directed.

38mm width of strip and 3mm thick of glass dividing strips for concrete flooring all as specified.

Non-skid coloured ceramic tiles of grade B II a / B II b of size 7 to 8 mm thick, area of each tile exceeding 0.09 sqm but not exceeding 0.11sqm, as in floor set and jointed in neat cement slurry and pointed in epoxy grout to match colour of tiles over and including 15mm thick screed bed of CM 1:6 complete all as specified and directed.

Glazed ceramic coloured printed tiles of grade B III in vertical surfaces for wall tiles of size 300 x 450 x 7mm thick as in dado set and jointed in neat cement slurry & pointed pointed in epoxy grout to match with color of tiles over and including 10 mm thick backing coat in cement motor 1:3 all as specified and directed.

Vitrified tiles light colour 10mm thick (square / rectangular) polished, area of each tiles not below 0.36 sqm, in floors etc, set and jointed over 5mm thick polymerized (latecrete) on existing tile and pointed in epoxy grout to match all as specified and directed.

Roughening surfaces of old concrete floor by picking sweeping clean and washing down with water to remove dust complete all as specified and directed.

Vitrified tiles light colour 10mm thick (square / rectangular) polished, size of tiles to match with that in floor, in skirting and dado including 10mm CM 1:3 render etc, set and jointed in neat cement slurry and pointed epoxy grout to match.

Dismantling of cudappa stone slabs, stone slab and tiles of any description or thickness in floors, aprons etc all as specified and directed.

M&L for Granite work (of any type), 40mm thick, (table rubbed and pre-mirror polished), in single piece, in steps, jambs, pillars, window cills, cooking platforms, wall cladding to lift and like, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including making hole for gas pipe including full rounding the edges of granite, laid over and including provision of screed bed or bedding layer, 15mm thick in CM 1:4, complete all as specified and directed.

Hi-traffic full body vitrified coloured tiles matt finish, 10mm thick (square / rectangular) polished, area of each tiles exc 0.18Sqm but not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 5mm thick polymerized (latecrete) on existing tile and pointed in epoxy grout to match all as specified and directed.

Saderhalli stone slab 20-25mm thick, using single piece stone slab in risers / thread / landing / skirting of staircase etc, to match in size and pattern, set and jointed in neat cement slurry and pointed in coloured expoxy grout to match, laid over and including provision of backing coat of CM 1:4, 15mm thick, including removal of stone slab, complete all as specified and directed.

Rendering 10mm thick in CM 1:3 on concrete surface even and smooth on roof surface including water proof liquid including roughing of old concrete surface. Note: Water proofing compound shall be measured and paid separately under respective item of this Schedule.

Chicken mesh of apertuer 12.5mm in least dimension with a weight not less than 0.4Kg/Sqm all as specified and directed.

Material and labour for roof treatment as follows:- (a) M&L Chip out the existing loosed bitumen / bitumen membrane completely reach up mother slab, clean the surface throughly to make it smooth and free of any foreigh material, repairs the concrete wherever damaged using PMM HS repairo, repairing of construction joints / cracks by chasing with cutting machine and fill the same with polymerized mortar in HS repairo, coving of 75 x 75mm should be made at the junction of wall and raft slab using polymerized cement mortar 1:4 admixed with advanced latex plus. (b) Applying one coat of 50% diluted self priming PU roof coat. Allow to dry bond coat for 4-6 hours before applying PU coat and surface to be cleaned before applying PU coat.

(c) Applying two coats of single component, cold applied, water based polyurethane modified acrylic dispersion with highly elastic and UV resistant water proofing treatment to the roof with HS PU Roofkoat of Berger or equivalent at 0.6 kg/Sqm for each coat without dilution confirming to ASTM D 6083-97a (Standard Specification for Liquid Applied Acrylic Coating Used In Roofing) each coat should allow to dry 4-6 hours. The component shall have a density of 1.25 to 1.3kg/per Litre, having tensile strentgh of 1.5N/mm2, having elongation of 350% with solid content not less than 60% in 2 coats. SRI value should be more than 100. The quoted rate shall include surface prepartion, repair the crack in mother slab by chasing with cutting machine and fill the same with polymerized mortar in CM 1:4 admixed with latex agent of reputed manufacture, making coving at junction, bore packing, treatment of construction joints completely as per manufacurer's specification and direction of the Engineer-in-Charge. Make: Berger / Bostic / Fosroc / Sika / Asian. Note: The above treatment shall be got carried out by the authorised applicator of the manufacturer approved by the GE.

Taking down / removing vegetation growth / plants of any size of area n.exc 0.5sqm above chajjas, roof slabs, parapet walls, junction of SWR pipe and wall etc up to roots and applying / injecting chemical and making good the surface in CM 1:3 up to height of 16 m all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position at level of 15 m high as in roof chajjas, fascia and parapet, RCC jalli any thickness and removing the debris out side MD land complete all as specified and directed.

Form work to chajjas and similar work rough flat finished surface concrete.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc. also splays between floors and beams, etc. rought finished surface concrete.

TMT Bars 6 to 8mm dia reinforcement for stirrups cut to length bent to shape required, including cranking, bending spirrally for hooping, binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending and binding with and including mild steel wire (annealed) not less than 9 mm dia complete all as specified and directed.

RCC 1:2:4 type B1 (normal mix) (using 20 mm graded stone aggregate) as in chajjas.

RCC 1:2:4 type B1 (normal mix) (using 20 mm graded stone aggregate) as in fins, facias, louvers, parapets.

RCC 1:2:4 type B1 (normal mix) (using 20 mm graded stone aggregate) as in beams, cantilivers, shelves, kitchen slabs.

Cleaning of loose scales & corrosion deposits from exposed reinforcement with steel wire brush or any other mechanical means of exposed steel after removing loose / damaged concrete complete all as specified and directed.

Applying one coat of anti corrosive agent NITOZINC primer on exposed steel surfaces (new & old) making sure the surfaces are properly coated complete all as specified and directed.

Epoxy resin concrete bonding agent NITOBOND EP on old exposed concrete surface for bonding new cementitious materials to existing cementitious surface complete all as specified and directed. Note for Sl item Nos. 131 to 140: The height of buildings is upto 16m, necessary cost of scaffolding shall be deemed to be included in the quoted rate.

Demolition of brickwork or stone / boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles.

Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width, type C1, 1:3:6 (20mm graded aggregate) and setting in cement mortar 1:4 complete all as specified and directed.

Precast cement concrete solid building blocks or slabs, type B1, 1:2:4 mix (using 20mm graded aggregate), 10cm thick (with plain or interlocking joints as directed) setting in cement mortar 1:4 complete all as specified and directed.

Brick work with sub class 'B’ bricks, built in CM (1:6) straight or curved on plan exc. 6 m mean radius etc., complete all as specified and directed.

Brick work with sub class 'B’ bricks, built in CM (1:4) straight or curved on plan on any radius etc., complete all as specified and directed.

Precast cement concrete in (1:2:4) type B1 using 20 mm graded stone aggregate as in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone wallin), corbels, brackets etc, (of any section indicated) with plain fair faces, including chamfers, weatherings, throating etc, and setting in mortar complete with joints to match in CM 1:6.

Pressure grouting 25 mm thick including any temporary shuttering to edges with cement mortar 1:2 complete all as specified and directed.

Pressure grouting 40 mm thick including any temporary shuttering to edges with cement mortar 1:2 complete all as specified and directed.

Precast reinforced cement concrete 1:2:4 type B0, (using 12.5 mm graded stone aggregate) as in pre cast cover slab of size 400 x 450 mm, 40 mm thick reinforced with hard drawn steel wire fabric of mesh size 150 x 150 mm and 4.75 mm dia wire including taking down cover slabs etc including necessary form work complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Mild steel plain black 2.24mm thick sheet in steel gates and similar work, cut to size, fixed to steel framing gates with plain 40mm lap joint with welded or riveted all directed.

Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc, and similar work conforming to Fe-290 Gde E-165.

Supply & fabricating for expanded metal weight not exceeding 4.00 Kg per Sqm, cut to length, bent to shape required & tying with including necessary welding steel frame work complete all as specified and directed.

Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165.

Pre-painted galvalume aluminum zine coating GI based corrugated steel sheet 0.50mm thickof an colour having tensile strength of 550Mpa as in roof covering fixed with slftapping screws as specified.

Taking down cement plastering of any thickness on brick, concrete or stone walls, partitions, ceilings etc including raking out joints, hacking for key, scrubbing down with water etc, removal of rubbish off the premises.

10mm thick rendering on brick or concrete surface in cement mortar 1:6 and finishing the surface with even and smooth without using extra cement all as specified and directed.

5mm thick rendering on ceilings in cement mortar 1:3 and finishing the surface with even and smooth without using extra cement all as specified and directed.

15mm thick rendering on brick or concrete surface in cement mortar 1:4 and finishing the surface with even and fair finish all as specified and directed. Note: Water proofing compound shall be measured and paid seperately.

Dubbing out average 15mm thick on irregular face of walls in Cement mortar 1:4 & rough cast plaster on brick work / concrete surfaces complete all as specified and directed. Note: Water proofing compound shall be measured and paid seperately.

Preparation of new plaster wall surfaces and applying two coats of oil bound distemper over a coat of alkali reistant primer on wall over 2mm putty complete all as specified and directed.

Preparing the newly plastered surfaces of ceilings and applying two coats of oil bound distemper over 2mm putty & primer all as specified and directed.

Preparing the newly plastered surfaces of walls and applying two coat of exterial emulsion over a coat of weather coat primer complete all as specified and directed.

Preparation of new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of old wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Complete removal of existing treatment and preparing the surfaces of ceilings plastered or unplastered and applying two coats of distemper oil emulsion over a coat of alkali resistent primer over 2mm thick wall care putty complete all as specified and directed.

Complete removal of existing treatment and preparing the surfaces of walls plastered or unplastered and applying two coats of distemper oil emulsion over a coat of alkali resistent primer over 2mm thick wall care putty complete all as specified and directed.

Complete removal of existing treatment and preparing the surfaces of walls plastered or unplastered and applying two coats of exterior emulsion paint over a weather coat primer complete all as specified and directed.

Repair to steel door of any descritption including replacement of handle steel hinges of any pattern, peg stay and replacement of MS sheet etc, to make steel door absolutely working condition, area of door not exceeding 2.50sq.m each including resecuring or easing and adjusting, complete all as specified and directed.

Complete removal of existing treatment and applying three coats of white wash on walls surface all as specified and directed.

Complete removal of existing treatment and applying three coats of white wash on ceiling surface all as specified and directed.

S&F, M-35 grade machine pressed precast concrete interlocking paver block any shape and size confirming to IS: 15658-2006 of 60mm thickness all as specified and directed.

M&L for 50mm thick sand filling under floors including watering and consolidation all as specified and directed.

S&F, chequered cement concrete commercial tiles 25cm x 25cm x 20 to 22mm / 30cm x 30cm x 20 to 25mm thick of with grey cement and pigment set jointed and pointed in neat cement slurry in floors and cut and polished laid and over and including 15mm screed in CM 1:6 including taking old tiles all as specified and directed.

S&F, 18/19mm thick colour PVC prelaminated board (Grade-I) fixed to timber frame work in a cup board shutter / shelves, pelmet box and similar items fixed in repair complete all as directed.

S&F, Auto closing hinges 35mm of 0 crank (KH-001) or B crank (KH-002) openable at 110 degree for kitchen cabinet shutters fixed in repair complete all as specified and directed.

S&F, Ball bearing runners 45mm Telescopic (KTS-20) full extension load capacity 50 Kgs fixed in repair complete all as specified and directed.

S&F, chromium plated SS wire basket (storage basket) pull out type for large utensils size 420 x 485 x 150mm of grade 304 with necessary nut bolt fixed in modular drawer box fix below kitchen platform all as per manufacturer specification, fixing clips etc, complete all as specified and directed. Product Code No. 6152 of Godrej or techno commerical equivalent model in any other make as approved by GE.

S&F, chromium plated SS wire basket (cup & saucer basket) pull out type, size 420 x 485 x 100mm of grade 304 with necessary nut bolt fixed in modular drawer box fix below kitchen platform all as per manufacturer specification, fixing clips etc, complete all as specified and directed. Product Code No. 6158 of Godrej or techno commerical equivalent model in any other make as approved by GE.

S&F, chromium plated SS wire basket (plate basket) pull out type, size 420 x 485 x 200mm of grade 304 with necessary nut bolt fixed in modular drawer box fix below kitchen platform all as per manufacturer specification, fixing clips etc, complete all as specified and directed. Product Code No. 6166 of Godrej or techno commerical equivalent model in any other make as approved by GE.

S&F, chromium plated SS wire basket (cutlery basket) pull out type, size 420 x 485 x 100mm of grade 304 with necessary nut bolt fixed in modular drawer box fix below kitchen platform all as per manufacturer specification, fixing clips etc, complete all as specified and directed. Product Code No. 6161 of Godrej or techno commerical equivalent model in any other make as approved by GE.

S&F, chromium plated SS wire basket (grain basket) pull out type, size 425 x 485 x 350mm of grade 304 with necessary nut bolt fixed in modular drawer box fix below kitchen platform all as per manufacturer specification, fixing clips etc, complete all as specified and directed. Product Code No. 6146 of Godrej or techno commerical equivalent model in any other make as approved by GE.

Providing and fixing factory made uPVC white color sliding window / ventilator three track made of extruded profiles with wall thickness of 2.3mm (+ 0.2mm). Window profile with hollow section with multi chamber. Frame 88mm x 52mm), sliding sash (42mm x 67mm), sliding mesh sash (42mm x 57mm) sliding interlock (one vertical length in each shutters) (45.5mm x 28mm). glazing bead (24.5mm x 16mm) will be mitred cut and fusion elded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (30mm x 18mm) 02 Nos. sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, hardware (Touch lock of zinc alloyed white powder coated). Steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed. Note: The unit rate quoted by contractor includes cost of glass & SS wire mesh and includes all other connected accessories. Net opening will be measured for payment purpose. (a) Area not exceeding 2.00 Sqmm each.

Taking down old U/S copper / aluminium point wiring (light / fan / socket or power socket, bell etc) complete including fixtures and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc for taking credit (credit shall be made as per conditions) and making good the disturbed surfaces of walls, floors, roofs etc complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-694 drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls, floors except in roofs duly chases cutting groove by chiselling / mechanically as required and making good the disturbed surfaces to match with existing surface and including GI modular boxes flushed in walls covered with modular white cover plates and frames of required size fixed with cadmium plated iron screws for mounting of modular switches, sockets, regulators etc and including 1.5 sqmm FRLS type PVC insulated, unsheathed, multistranded copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and directed for one light point, ceiling fan / exhaust fan point controlled by one, one-way switch.

All as per Sl item No. 187 above, but for one call bell point controlled by one bell push.

All as per Sl item No. 187 above, but for one light point controlled by two, 2-way switches.

All as per Sl item No. 187 above, but for one 5pin socket outlet point controlled by one 5 Amps switch on the same board.

All as per Sl item No. 187 above, but for one 5pin socket outlet point controlled by one 5 Amps switch on independent board.

All as per Sl item No. 187 above, but wiring with 2.5 sqmm and earth continuity conductor with 2.5 sqmm for 6 pin, 15 Amps socket out let point on independent board.

All as per Sl item No. 187 above, but wiring with 4.0 sqmm and earth continuity conductor with 4.0 sqmm for 6 pin, 15 Amps socket out let point on independent board.

S&F, Modular type switch single pole, one way, 5/6 Amps, 240 volts, one module.

S&F, Modular type switch 5/6 Amps, single pole, 2-way, 240 volts, one module.

S&F, Modular type socket out let, 5 Pin, 5/6 Amps, two module, 240 volts.

S&F, Modular type switch outlet 6pin, 6A/16 Amps, 240 volts, two module.

S&F, Modular type switch, single pole, one way,16 Amps, 240 volts, one module.

S&F, Modular type fan regulator electronic type, 230 Volts, stepped type 120 Watts, two module.

S&F, Modular type Bell push flush type 5 Amps.

S&F, call bell ding dong type, 230 Volts, AC and fixing on suitable base plate.

S&F, ceiling rose surface bakelite 65 x 50 mm, three terminals 230 volts, AC.

S&F, VTPN MCCB DB 4 way, 415V, 50Hz, AC, double door IP 43 protection suitable for MCCB 4 pole upto capacity 100 Amps, 25 KA as incomer and SP/TP MCB's as outgoings comprising of busbar, neutral bar, duly powder coated painting and fixed flush in wall and making good the disturbed surfaces to match with existing surface and making electrical connections using suitable sizes of copper thimbles / lugs including taking down old unserviceable item complete all as specified and directed.

S&F, VTPN MCCB DB 8 way, 415V, 50Hz, AC, double door IP 43 protection suitable for MCCB 4 pole upto capacity 100 Amps as incomer and SP/TP MCB's as outgoings comprising of 200A (04 Nos) busbar, neutral bar, duly powder coated painting and fixed flush in wall and making good the disturbed surfaces to match with existing surface and making electrical connections using suitable sizes of copper thimbles / lugs including taking down old unserviceable item complete all as specified and directed.

S&F, VTPN MCCB DB 12 way, 415V, 50Hz, AC, double door IP 43 protection suitable for MCCB 4 pole upto capacity 125 Amps as incomer and SP/TP MCB's as outgoings comprising of 200A (04 Nos) busbar, neutral bar, duly powder coated painting and fixed flush in wall and making good the disturbed surfaces to match with existing surface and making electrical connections using suitable sizes of copper thimbles / lugs including taking down old unserviceable item complete all as specified and directed.

S&F, fixed type MCCB 125 Amps, TPN 16 KA, 415 V, AC including taking down existing unserviceable items complete all as specified and directed.

S&F, fixed type MCCB 100 Amps, TPN 16 KA, 415 V, AC including taking down existing unserviceable items complete all as specified and directed.

S&F, MCB DB SPN 12 way, 240V, 50Hz sheet metal enclosure double door type IP-43 protection, factory made powder coated painting and tinned copper bus bar 200 Amps neutral link fixing flush in wall and making electrical connections including removing old items all as specified and directed.

S&F, MCB DB SPN 8 way, 240V, 50Hz sheet metal enclosure double door type IP-43 protection, factory made powder coated painting and tinned copper bus bar 200 Amps neutral link fixing flush in wall and making electrical connections including removing old items all as specified and directed.

S&F, MCB DB 4 way, SPN, 240 V, 50Hz, AC, double door IP 43 protection with 200 Amps busbar, neutral bar, earth bar complete with powder coated painting and fixing in flush with wall and making good match with existing surface and making electrical connections using suitable sizes of thimble copper lugs etc including taking down existing unserviceable items complete all as specified and directed.

S&F, MCB SPN 40 Amps working on 240 volts 50 Hz AC supply, 10 KA 'C' series including taking down existing unserviceable items complete all as specified and directed.

S&F, MCB SP 6 to 32 Amps, 10 KA C curve, 240 volts 50 Hz AC including taking down existing unserviceable items complete all as specified and directed.

M&L for submain wiring with 2 run of 10 Sqmm, single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-1554 Part-I drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls, floors except in roofs duly chases cutting groove by chiselling / mechanically as required and making good the disturbed surfaces to match with existing surface including 1 run of 10 Sqmm PVC insulated, single core, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade as earth continuity conductor and connecting to common earth dolly including taking down old item all as specified and directed. Note: 2 runs of 10 Sqmm copper conductor and 1 run of 10 sqmm copper conductor and 1 run of PVC conduit shall be measured as one unit.

M&L for submain wiring with 2 runs of 6 Sqmm, single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-1554 Part-I drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls, floors except in roofs duly chases cutting groove by chiselling / mechanically as required and making good the disturbed surfaces to match with existing surface including 1 run of 6 Sqmm PVC insulated, single core, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade as earth continuity conductor and connecting to common earth dolly including taking down old item all as specified and directed. Note: 2 runs of 6 Sqmm copper conductor and 1 run of 6 sqmm copper conductor and 1 run of PVC conduit shall be measured as one unit.

M&L for submain wiring with 2 runs of 4 Sqmm, single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-1554 Part-I drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls, floors except in roofs duly chases cutting groove by chiselling / mechanically as required and making good the disturbed surfaces to match with existing surface including 1 run of 4 Sqmm PVC insulated, single core, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade as earth continuity conductor and connecting to common earth dolly including taking down old item all as specified and directed. Note: 2 runs of 4 sqmm copper conductor and 1 run of 4 sqmm copper conductor and 1 run of PVC conduit shall be measured as one unit.

M&L for submain wiring with 2 runs of 2.5Sqmm, single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-1554 Part-I drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls, floors except in roofs duly chases cutting groove by chiselling / mechanically as required and making good the disturbed surfaces to match with existing surface including 1 run of 2.5 Sqmm PVC insulated, single core, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade as earth continuity conductor and connecting to common earth dolly including taking down old item all as specified and directed. Note: 2 runs of 2.5 Sqmm copper conductor and 1 run of 2.5 sqmm copper conductor and 1 run of PVC conduit shall be measured as one unit.

S&F, sheet metal enclosure with a two pin and earth plug and socket complete with MCB SP 20A, 10 KA 'C' curve, 240V, 50 Hz, AC including taking down existing unserviceable items complete all as specified and directed.

S&F, exhaust fan 300mm sweep metallic body single phase 230V, complete with blades, frame and other accessories as supplied by manufacturer and necessary fixing arrangement on wall surface by providing round hole with providing louvers including making electric connection with 3 core copper cable.

S&F, exhaust fan 250 mm sweep metallic body single phase 230V, complete with blades, frame and other accessories as supplied by manufacturer and necessary fixing arrangement on wall surface by providing round hole with providing louvers including making electric connection with 3 core copper cable.

Taking down and dismantling old existing ceiling fan from any position of any make / size and carrying out servicing and overhauling including replacement of capacitor, bearings, bush, shaft, rubber reel assembly, canopy and minor parts as required including one coat of spray painting of existing shade, marking MES No with black paint and refixing the same and making electric connections by providing 3 core copper conductor cable from ceilng rose to fan all as specified and directed.

Taking down and dismantling existing exhaust fan of any size and carringout servicing, overhauling including replacing unserviceable parts, components with new parts and fixing the same in existing location and making electric connection with 3 core copper cable all as specified and directed.

S&F, 20W 4' LED batten surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption < 20W, luminaire lumen > 1000 lm, system efficiency of > 100 lumens / W, LED with LED binning as per ANSI Bin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class 1, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 450C, driver efficiency > 85%, power factor > 0.9, THD < 20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50,000 burning hrs (min) as per L7O criteria, two stages isolated constant current operated driver with range 150-270V AC and safety extra low voltage safe level < 60 V DC as per IEC standard with LM70 & LM 80 certification including taking down existing unserviceable items all as specified and directed.

All as per Sl item No. 222 above, but of capacity 9/10 Watt 2' including taking down existing unserviceable items.

S&F, lamp holder PVC / polycarbonate type with back plate suitable for batten fittings and fixing on base plate as per IS-1258 including taking down existing unserviceable items all as specified and directed.

S&F, LED bulb 10 Watt, 230 V taking down complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6.3 mm thick buried in ground vertically to a depth not less than 2.25 metresbelow normal ground level with top edge of earth plate not less than 1.5 metres below normal ground level including earth lead wire GI 4mm dia connected galvanised iron earth plate by means of GI bolts, nuts, check nuts and washers all as shown in electrical plate No. 3 of MES SSR Part-I connected to earth test point all as specified or indicated including testing on completion with and including 15 mm bore light grade GI protection pipe 7.5 metres long including PCC 1:2:4 pit with pre-cast RCC 1:2:4 type B1 cover 40 mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hook made out of 6mm dia MS bars watering arrangement pipe of 20mm dia medium grade with wire mesh funnel andproviding common salt and charcoal filling all around earth plate upto 15cm thick and necessary excavation and earth work in any type of soil and returning filling of soil, removing surplus soil etc complete all as specified and directed.

M&L for earth continuity conductor 4 mm dia galvanised iron or steel wire fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing or main earth wire all as specified and directed.

S&F, non-metallic rigid PVC conduit 25mm dia medium grade with conduit accessories concealed / surface in walls, floors etc and providing fish wire in conduit to draw TV / Telephone wire including chases cutting all as specified and directed.

S&F, LED building security light fitting 35/36W made up of die cast housing with toughend glass and high power LEDs complete with IP 65 protection duly pre-wired and fixing arrangement on wall surface at suitable height by providing GI bracket medium grade of suitable size and adequate length with necessary fixing GI clamps, washers, nuts & bolts and making electric connections by providing 3 core copper conductor cable from ceiling rose to light fitting all as specified and directed.

S&F, 25mm GI tubing in walls / roof, medium grade, with all fittings including taking down old complete all as specified and directed.

S&F, 25mm gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed with all fittings including taking down old complete all as specified and directed.

C R R CONSTRUCTIONS

SIGNATURE INFRASTRUCTURES(E DHARANI KUMAR REDDY)

Phoenix Infra

Sri Lakshmi Constructions

M/s M Munivenkatappa and Company

UNITED TECHNO PROJECTS PVT LTD

Shekhar Enterprises