COMPREHENSIVE MAINTENANCE AND REPAIR IN THE AOR 13 AND 55 UNDER GE (A) JAISALMER. (CPP SERIAL No. 08)

Amount

B/R PORTION:- Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm including cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge.

S & F Spray duco painted Pressed steel frames made of MS sheet of 1.20mm thickness of size 105 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etc complete all as specified and as directed by the Engineer-in-Charge. Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be repaired to match with exisitng finish. Cost of the same will be included in this items

S & F Spray duco painted Pressed steel frames made of MS sheet of 1.20mm thickness of size 125 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etc complete all as specified and as directed by the Engineer-in-Charge. Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be repaired to match with exisitng finish. Cost of the same will be included in this items

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge.

S & F solid PVC door frames of size 50x47mm made out of 5mm plain colour PVC sheet supplying and fixing in opening as per specification and drawing shown in SSR complete all as specified and as directed by the Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification complete all as specified and as directed by the Engineer-in-Charge and also including S&F following Items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf

Taking down shutters of any description exc 1sqm but not exc 2.00 sqm each complete all as specified and as directed by the Engineer-in-Charge.

S&F Factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 2nd class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters complete all as specified and as directed by the Engineer-in-Charge and also including S&F following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm) complete all as specified and as directed by the Engineer-in-Charge and also including S&F following items:- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x3000mm - 1 nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf

S&F in repairs stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixedd with tinned tacks or stainless steel wire staples or with wooden beads, stainless steel screws and nuts bolts etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint, first quality, over a coat of pink primer on wooden surface complete all as specified and as directed by the Engineer-in-Charge.

Taking down aluminium door/ windows incl frames and complete fittings of area exc 1.00 sqm but n. exc 4 sqm complete all as specified and as directed by the Engineer-in-Charge.

Powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.20mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and incl mortice lock with duplicate keys etc complete all as specified and as directed by the Engineer-in-Chargeand also including S&F the following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

Providing and fixing factory made aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60 x 44.45 x 1.29 mm and shutters made of 63.5 x 31.75 x 1.29 mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36 mm dia and 1.40 mm aperature in inner shutters complete fixed in all respect complete all as specified and as directed by the Engineer-in-Charge and also including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 2 nos per leaf (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

S & F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, including removal of existing grill all complete as per requirement complete all as specified and as directed by the Engineer-in-Charge.

Powder coated 50 microns extruded aluminium frame for fixed type partition (Standard two panel pattern) made out of powder coated aluminium section of size 63.5 x 38.10 x 1.5mm, comprising of 5mm thick tinted glass inserted in and including necesary jointing cleats, rubber packing, anodised aluminium snap beading complete fixed to floor and wall by means of cadium plated steel screws complete including taking down of existing partition with all fittings and fixtures complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs door closer hydraulically regulated designation No 3 universal type suitable for door shutter 851mm to 1000mm vide and weight between 61 to 80 kg of aluminium (extruded section body) complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair 300mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate, bearing ISI mark complete including necessary welding work complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs 150 mm over all length floor door stopper, bearing ISI mark, of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair Double action floor spring ISI marked hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair of 3mm thick Fibre-reinforced plastic sheet of transparent colour of any of size including necessary screw and other accessories including hacking out the same from window or door frame complete all as specified and as directed by the Engineer-in-Charge. Note: Cost of Scaffolding for change of sheet upto four story building also include in the rate.

S&F in repairs Stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete including 02 Nos stainless steel brackets/finials fancy type, stops fixed with ss screws etc complete all as specified and as directed by the Engineer-in-Charge. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete all as specified and as directed by the Engineer-in-Charge.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long ccomplete all as specified and as directed by the Engineer-in-Charge.

M&L for Anodised aluminium snap grid frame work for false ceiling complete all as specified and as directed by the Engineer-in-Charge. Note :- (i) Main tee, cross tee shall be 35x25x1.5mm & 25x25x1.5mm respectively. Angle at end all along the walls shall be 40x25x2mm. (ii) Rate quoted by the contractor shall deemed to inclusive of frame work complete.

M&L for Exposed metal frame ceiling with 6mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and as directed by the Engineer-in-Charge.

M&L for providing and fixing gypsum board 12mm thick in ceilingfixed with screw as per manufacturer instructions complete all as specified and as directed by the Engineer-in-Charge.

M&L for prepration of new surface and applying two coat of Oil bound distemper on ceiling surface complete all as specified and as directed by the Engineer-in-Charge.

S&F hollow PVC Wall panelling consisting of 5mm thick decorative colour PVC sheet inclusive of fixing at site on aluminium frame as per specifications and drawing including supply and fixing of all accessories like fastners / screws / solvents / beadings etc all complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair Vitreous china premium/1st quality urinal bowl type of white colour, of size 330x300x450mm incl providing and fixing plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs with and incl S&F of all accessories for fixing as recommended by manufacturer like 60mm long brass secrews/fasteners/rag bolts etc, pointing urinal back in white cement; connecting for discharge pipe incl necessary packing, union complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Urinal spreader of PTMT any colour for fixing with 15mm dia pipe. (Minimum weight 60gms) complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair 6mm thick of size 600x450mm looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish without any beading, including ends/edges of the mirror to be tapered etched smooth finish etc.complete fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair Vitreous china squatting pan of Orissa patten size 580 x 440 white colour including CI S/P trap long size as directed joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in PCC 1:2:4 complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair European type water closet including CI P/S trap as directed including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe PVC 32mm dia and incl. plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and including supply and fix of PVC long arm P/S trap so that joint is avoided inside the building as well as in wall and outlet straight away come out of wall in all floors G.F.and taking down existing of any description/size complete all as specified and as directed by the Engineer-in-Charge.

S&F Vitreous china premium/1st quality wash down water closet floor mounting EWC (One piece) P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe PVC 32mm dia and incl. plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, incl 100mm dia cast iron sanitary connections short connections pipe of length upto 600 mm and Cutting holes in or through walls, packing with PCC 1 : 2 :4 complete and including taking down existing of any description/size complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs plastic EWC seat cover, coloured closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by the Engineer-in-Charge.

S&F Flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and including taking down existing of any description/size complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair Vitreous china premium/1st quality wash basin (under counter), white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by the Engineer-in-Charge. Note : The items for counter will be measured and paid separately.

S&F in repair PVC connection 450mm long and 15 mm dia with brass fly nut at both ends complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs brass chromium plated Health faucet with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

Supply & Fixing in repair chromium plated shower rose 125mm round shape fancy type fixed to 15mm bore pipe complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair Toilet paper holder with flat recessed type stainless steel complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair stop/angle cock copper alloy but fancy type and chrominum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15 mm bore dia of pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 15mm bore Brass CP basin mixer for mixing hot & Cold water screwed down for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Brass CP wall Mixer 3 in 1 System with provision for overhead and hand shower suitable 15mm bore of pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair stainless steel Towel Rack with lower hanger size 24'' (600 mm) fixed to walls with hook etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair of fancy type pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shank supply and fixing ly nuts for iron pipe of 15mm bore fancy type complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Bib taps, CP, fancy type long nose with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete fixed as in repair in all respect complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 15mm bore stop valves , cast copper alloy, chromium plated fancy type with long shank cup (Concealed type) screwed down , high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs Tubular towel rail brass chromium plated 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs stainless steel sink with drainage board , made out of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast iron cantilever bracket of overall size 915x460mm bowl size 410x330x160mm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs stainless steel sink, made out of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast irn cantilever bracket of 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC Flexible waste pipe 32/40 mm dia having length 900mm with socket for steel sink/WHB upto floor level complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 15mm bore tubes medium grade galvanized with all fittings such as Tee, elbows, sockets, unions, plugs, short lenghts etc. and fixed complete to walls and ceilings or laid in floors concealed or open of any length including taking down or up existing GI tubing & connections complete all as specified and as directed by the Engineer-in-Charge.

S&F 20 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length including taking down or up existing GI tubing & connections complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down steel tubing 20 mm and connections, including cleaning for re fixing or removal complete all as specified and as directed by the Engineer-in-Charge.

Supplying and laying of CPVC pipes 20 mm external Dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed by the Engineer-in-Charge.

S&F CPVC Brass Elbow 20mm ext dia complete all as specified and as directed by the Engineer-in-Charge.

S&F CPVC Brass Elbow (3/4 X 1/2) 20mm Ext Dia complete all as specified and as directed by the Engineer-in-Charge.

S&F Brass Tee 20 mm Ext dia complete all as specified and as directed by the Engineer-in-Charge.

M&L for Cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete all as specified and as directed by the Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes (any type or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge.

S & F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-charge.

S & F in epair PVC (SWR) 110mm bends any radius complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair PVC (SWR) vent cowl 110mm dia complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair PVC (SWR) 110mm dia in junction single, (Single T) equal or unequal complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for fixing 110mm dia PVC pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed by the Engineer-in-Charge.

S&F inepair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F inepair PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge.

S&F inrepair PVC (SWR) 75mm bends any radius all as specified and directed.

S&F inrepair PVC (SWR) 75mm dia in junction single, (Single T) equal or unequal complete all as specified and as directed by the Engineer-in-Charge.

S & F inepair PVC (SWR) branch piece 75mm, single (single Y) equal or unequal with access door bend complete all as specified and as directed by the Engineer-in-Charge.

S & F in epair PVC (SWR) multi floor trap 75 mm with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for fixing 75mm dia PVC pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed by the Engineer-in-Charge.

Dismantling, floor, hearth or wall tiling including CM (bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete un-reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified and as directed by the Engineer-in-Charge.

M&L for broken bricks filling of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by the Engineer-in-Charge.

M&L plain cement concrete 1:2:4 type by using 20mm graded stone agregate as in flooring with water proofing compound @ 2% dosage (1kgs) in 50kg cement including demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified and as directed by the Engineer-in-Charge.

Supply of SBR based waterproofing compound @ 2% dosage by weight of cement (1kgs) of 50kg cement used to be mixed in cement concrete as water proofing and hardening complete all as specified and as directed by the Engineer-in-Charge.

M&L for applying Pitch Free PU based Liquid applied single component elastomeric seamless, water and vapor proof membrane system Nitoproof 600PF for concrete @ 2.50 kg/m2 (2 coats). Typical applications will include roofs, podiums, balconies, floor slabs, suspended floors, patios, bathrooms, inspection pits, swimming pools, bridge decks, Conforming Tensile Strength (2N/mm2 ) (ASTM D412) / Tear resistance (15 kN/m) (ASTM D624-00 and Crack bridging (ASTM C836 / ASTM C1305 modified)2mm. After 72 hours of curing, flood test can be carried out to a minimum depth of 50mm of water for 24 hours. Drains shall be plugged and barriers placed to contain the water including taking down of existing treatment complete all as specified and as directed by the Engineer-in-Charge. Note : All above operations to be done in presence of auth applicator in order all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase of flooring / hard standing complete all as specified and as directed by the Engineer-in-Charge.

M&L for plain cement concrete 1:2:4 type B 1 using 20mm graded stone agregate cast in situ kerb stone, copings, bed plates complete all as specified and as directed by the Engineer-in-Charge.

M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/ highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge.

M&L for Non Skid ceramic tiles colour tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

M&L for Non-skid ceramic premium quality coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 15 mm thick screed in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge.

M&L for vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of light coloured tiles as in approved shade, set & jointed in neat cement including and over 15mm th screed bed in CM (1:6) and pointed in white coloured cement to match, in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for ceramic out door tiles 300mmx300mmx10mmm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 15 mm thick Cement Mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortarcomplete all as specified and as directed by the Engineer-in-Charge.

M&L for Granite of black / green / imperial red (colour as approved by Accepting Officer) of any type machine cut as in shelves/steps/counter tops, 20 mm thick, set and jointed in cement slurry over & including screed or 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified and as directed by the Engineer-in-Charge. Note : Single piece should be used in steps/cills/jambs/shelves.

M&L for Jaisalmer stone for wall cladding (of any type) 35-55 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of stone , exc .0.06 sqm but not exc 0.11 sqm ,including cutting and polishing types in wall including 20 mm thick CM 1:4 for laying Jaisalmer stone complete all as specified and as directed by the Engineer-in-Charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete, complete all as specified and as directed by the Engineer-in-Charge.

M&L for Mirror polishing on old marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of Trellis work (Jafri) of any description, including bottem runner and taking as under of battens in trellis (posts and rails measured separately) complete all as specified and as directed by the Engineer-in-Charge.

M&L for providing Stone jalies Jaisalmer type 48-50MM thick and 60 cm high fixed in line including stone pillar having size 100 x 100 MM height 70 CM fixed in cement mortar 1:4 fixed on stone runner beam (stone piller measured with Jali) including filling of joints with pigment of same colour complete all as specified and as directed by the Engineer-in-Charge.

M&L for providing bottom runner stone beam ( Jaisalmer type) fixed in line having size 100 x 200 MM fixed in cement mortar 1:4 and making ready for fixing of jaisalmer stone jalies and pillar complete all as specified and as directed by the Engineer-in-Charge.

M&L for precast cement concrete solid block masonry exc 10cm in width and setting in CM 1:6 type C1, 1:3:6 including Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches,pillars etc complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement plaster of any description, any thickness from external surfaces of walls/soffits etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 15 mm thick readymade plaster on inner/outer walls with UltraTech READIPLAST by adding 17-19% of potable water by weight of material. For thickness above 15 mm it is recommended to be applied in multiple layers. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the Compressive strength @ 28 Days- 10-12 Mpa/ Bulk density- 1500-1600 Kg/m3. complete all as specified and as directed by the Engineer-in-Charge. Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height all as specified and directed

Supply only integral liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge.

M&L for Applying 1 mm thick wall care putty on wall for desired smoothness and levelling of surfaces in two or more layers) for receiving painting complete all as specified and as directed by the Engineer-in-Charge.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L for distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified and as directed by the Engineer-in-Charge.

M&L for plain sheet glass plain 3mm thick ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane including hacking out of old/broken glass complete all as specified and as directed by the Engineer-in-Charge.

M&L for taking down carefully existing aluminium/ copper point wiring (light, fan, socket or power) complete fittings fixture such as switches Ceiling roses, pendents,regulators, sockets etc to be measured separately)unscrewing from Board/outlet boxes, fittings & fixtures such as switches, sockets, ceiling rose lamp holder tube/ceiling fitting, bulk head fittings, tube lights & regulator etc and making good disturbed surfaces of walls, floors etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L for taking down carefully existing old DBs and making good disturbed surfaces of walls to match the existing surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L for taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L for point wiring (modular type) with two run of PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm (FRLSH), PVC conduit medium grade/ PVC casing caping and pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc) and drawing one run of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor cable (FRLSH) as earth continuity wire in green colour connected to common earth and each terminal box/fitting complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) Modular switch and socket shall be measured and paid separately. (In ceiling Portion surface conduit wiring shall be carried out.) Note: The quoted rate inclusive for the following :- (a) GI metal flush box and Modular cover plate with frame of any module complete. (b) Proper colour coding is to be followed as per IS Specification. (c) wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (d) Cutting chases/making good disturbed surfaces of wall for fixing concealed conduit wherever required will be measured and paid separately.

All as per item No. 111.00 her-in-before above but one light point controlled by one one way switch.

All as per item No. 111.00 her-in-before above but one fan point controlled by one one way switch.

All as per item No. 111.00 her-in-before above but one 3 pin socket outlet 5/6 Amps independent.

All as per item No. 111.00 her-in-before above but one 3 pin socket outlet 5 Amps on the same board with other switches

All as per item No. 111.00 her-in-before above but one light point controlled by two 2-way switches.

All as per item No. 111.00 her-in-before above but one bell/ buzzer point controlled by one push button

All as per item No. 111.00 her-in-before above but cable with 4.0 sqmm size for socket outlet 15 amps, independent board

M&L for submain wiring with two single core PVC insulated unsheathed multistranded copper conductor cable of size 6 sqmm (FRLSH) and one single core PVC insulated unsheathed multistranded copper conductor cable green colour of size 6 Sqmm (FRLSH) as earth lead in and including concealed with PVC conduit medium grade of suitable size or surface wiring with PVC casing caping of suitable size and making good the disturbed wall surfaces to match with existing specification including takind down unserviceable submain wiring complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Three run of cable with one run of PVC conduit and caping will be measured as one length. (ii) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (iii) Cutting chases/making good disturbed surfaces of wall for fixing concealed conduit wherever required will be measured and paid separately.

All as per item No. 113.00 her-in-before above but 4.0 sqmm cable complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 113.00 her-in-before above but 2.5 sqmm cable complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 113.00 her-in-before above but 1.5 sqmm cable complete all as specified and as directed by the Engineer-in-Charge.

S&F ceiling Rose, 3 terminal polycarbonate isolated body complete all as specified and as directed by the Engineer-in-Charge.

S&F modular switch one way 6 Amps, 1 module complete all as specified and as directed by the Engineer-in-Charge.

S&F modular switch two way 6 Amps, 1 module complete all as specified and as directed by the Engineer-in-Charge.

S&F modular switch one way 16 Amps, 1 module complete all as specified and as directed by the Engineer-in-Charge.

S&F modular bell push 6 Amps, 1 module complete all as specified and as directed by the Engineer-in-Charge.

S&F modular socket, 2/3 pin 6 amps, 2 module complete all as specified and as directed by the Engineer-in-Charge.

S&F modular socket, 2/3 pin 6/16 amps, 2 module complete all as specified and as directed by the Engineer-in-Charge.

S&F LED box type Integrated Batten Wattage 20 watt having Aluminum Extruded housing in white powder coated Finish with high translucent PC Cover, Dimension of the Fixture Must not be less Then Length 1170 MM (± 5 MM ), Elegant Design, IP 20 Protection. Minimum Lumens output of the fitting shall be 2500 Lumens With Efficacy of 125 lm/W, CCT 5700 – 6500K, Surge Protector 4 KV, PF>= 0.95 , Necessary mounting arrangements. The Manufacturer of the fixture shall have in house NABL Accredited Lab and must produce certificate of the same along with LM-79 / LM-80 / Test Report complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair LED 20W inverter batten type fitting 3/4 feet long aluminium extruded housing, charging time 10-12 Hrs with 04 Hrs backup,IP-20 ,rated voltage 230 V, 50 Hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by the Engineer-in-Charge.

S&F for LED tube light fitting 10 Watt, 2 Feet or 591 MM in length, IP 20 Protection, wall mounted type, Slim LED Batten with extruded aluminium housing and polycarbonate diffuser, elegant design with end caps, having excellent thermally managed polycarbonate extrution, LM 80 Certified LED having Integral Electronic Constant Current Driver, IP 20 Protection, Opreating voltage 240 V , 50Hz AC Supply and Operating tempraeture 0 to 50 C, Power factor ≥ 0.9, Lumen output ≥ 1000, necessary mounting arrangements on PVC Square box 2 Nos, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair for LED down lightrecess mounted/Surface mounted/POP mounted or as per site requirement, square/Round type worm white / Neutral white or 2700 K- 3000 K as per user requirement 18 watts with efficiency of 100 lumens per watt, in worm white/ neutral white as per site requirement sleek design aluminium housing polycarbonate diffuser white finish operating voltage from ceiling rose to fitting complete all as specified and as directed by the Engineer-in-Charge.

S&F recessed/ceiling mounted down lighter with CRCA housing with high bright LED,idealy suited for low ceiling areas Brilliance 36watt LED, size 2ft x 2ft The product features color tuning from CCT 3000K – 6000 k, Surge Protector 4 KV, PF>= 0.95 , necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair recess mounted/Surface mounted/POP mounted or as per site requirement LED down light 06 Watt round/Square in shape worm white or 2700 K- 6000 K as per user requirement Ideal for wardobes, furniture lighting, display & interior decoration of complete all as specified and as directed by the Engineer-in-Charge. Note for item Nos. 124 to 129:- (i) Driver efficiency more than 85% (Constant current driver) (ii) Non isolated type driver (iii) THD less than 20% (iv) LED driver current less than 60 mA (v) Efficiency of LED Chip more than 130 lm/watt (vi) Efficiency of LED Fixture 100 lm/watt (vii) Surge protection 2.0 KV & above as per IEC standard (viii) working humidity 95%RH (ix) Life 50000 Hrs at 70% lumes (x) CRI more than 80 (xi) Working temp -10 degree to 50 degree C (xii) Heat Sink extruded aluminum (xiii) junction temperature 85 degree C (xiv) Body of fitting Extruded Aluminum (xv) impact code Min IK 03 or more ( xvi) LM79 report from thir party (instead of company in house lab) NABL/UL accredited lab (xvii) LM 80 report from LED manufacturer (xviii) Low/High voltage, reverse polarity, overload and short circuit protection inbuilt in fixture (xix) IP-20 (xx) Test certificates to be submitted before commencement of work/ claiming for payment . (xxi) Warranty certificate for minimum 2 years to be submitted from OEM.

S&F in repair LED bulb 9 watt, warm white B-22 complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair LED inverter bulb 12 Watt, CDL, 220V AC complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Bell, Ding Dong AC, 230 Volts complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair MCCB DB VTPN 4 way IP-54, IK-09 made of sheet steel phos phatised, powder painted with suitable rated bus bar as per OEM design, neutral link, earth bar and Din rail 415 Volts with double door, suitable for MCCB 4 Pole 100 Amps as incomer and MCB Single Pole as outgoing complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair sheet metal enclosure with TPN MCB DB's 4 way (grouted in walls) double door type IP-54, IK-09 Protection. Isolated Neutral, Door earthing, with suitable rated bus bar as per OEM design including suitable size of copper ferrules for fixing of cable complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair MCB DB's SPN 4 way, IP-54, IK-09 double door, sheet metal enclosure, 240V, with suitable rated bus bar as per OEM design including suitable size of copper ferrules for fixing of cable complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) MCCB and MCB will be measured and paid separately. (ii) The cost for flushing of Distribution box in any type of wall and making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate

S&F in repair MCB DB's SPN 8 way, IP-54, IK-09 double door, sheet metal enclosure, 240V, with suitable rated bus bar as per OEM design including suitable size of copper ferrules for fixing of cable complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) MCCB and MCB will be measured and paid separately. (ii) The cost for flushing of Distribution box in any type of wall and making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate

S&F in repair Single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair MCCB 4 Pole, 415V, Adjustable type, 100 to 125 Amps with breaking capacity 16 KA complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair MCB TPN 40 to 63 Amp, C series, 415V, 10 KA complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair RCBO 25-40 Amps, double pole 240V, AC type, 30 mA complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair MCB SP 6-32 Amps,10 KA, B Curve, 230 Volts, 50 HZ complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Surge Protection Device, breaking capacity 40KA/Pole, 4 Pole with sheet metal enclosure complete all as specified and as directed by the Engineer-in-Charge.

S&F Thermoplastic/ Polycarbonate/ sealed moulded meter box, IP-43, weather proof & water proof single door with locking arrangement, transparent meter viewing window glass suitable for smart single phase meter complete all as specified and as directed by the Engineer-in-Charge.

M&L for cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed PVC Conduit etc., and making good, cutting not exceeding 10 cm girth etc., including making good disturbed surfaces with existing wall colour complete all as specified and as directed by the Engineer-in-Charge.

M&L for carrying out internal wiring test with all T&P such as megger, clamp meter/multi meter etc., by opening of main DBs/TPN DBs/SPN DBs disconnecting of phase and neutral cable connection, fittings, fixtures carrying out testing for insulation values, reconnecting the disconnected cable connections, fittings and fixtures including replacement of defective copper ferrules, insulation peeled off wires with insulation tape complete all as specified and as directed by the Engineer-in-Charge. Note : (i) The cost of copper ferrules and insulation tape shall be deemed to be included in the quoted rate. (ii) The inspection shall be carried out in presence of JE E/M, I/C Elect(HS)/MCM detailed by JE E/M with user's signature. (iii) Each Building will be measured as one job.

Repair, maint and making the continuity of supply after rectifying the defects of the electrical items such as switches, sockets, bell push, ceiling roses, metal/PVC flush boxes, modular cover plate with frame and other similar electrical items/fittings etc. including providioning of small pieces of electrical wire if required of size 1.5 sqmm to 2.5 sqmm single core and length not exceding 0.50 mtrs complete all as specified and as directed by the Engineer-in-Charge. Note :- (i) any accessories found unserviceable that shall be paid as supply only under respective items of this BOQ. (ii) One job only will be considered for each bldg/Qtr per day irrespective of the No of points made serviceable. (iii) The area for attending the complaints are Jaisalmer Cantt (iv) Each complaint attended/rectified shall be measured as one job. (v) The contractor shall depute necessary man power on daily basis for rectifying the jobs including sundays and holidays.

Supply only bell push, flush type 5/6 amps for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only switch socket combination 2 in 1, 3 pin, 6 and 16 Amp flush type for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only switch socket combination 2 in 1, 6 Amp flush type for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only ceiling Rose, 3 terminal polycarbonate isolated body for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only modular switch one way, 6 Amps, 1 module for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only modular switch one way, 16 Amps, 1 module for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only modular socket, 2/3 pin, 6 amps, 2 module for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only modular socket, 2/3 pin, 6/16 amps, 2 module for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only modular metal/PVC flush box 3 module for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only modular metal/PVC flush box 6 module for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only modular white cover plate with frame 3 module for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only modular white cover plate with frame 6 module for carrying out repairs underrelevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only socket outlet 2 in 1, 3 pin, 6 and 16 Amp flush type for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only socket outlet 2 in 1, 6 Amp flush type for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only fan regulator flush type for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only metal clad plug 20 Amp 3 pin for carrying out repairs underrelevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only FRLSH PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm , cut to size all as required at site for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only FRLSH PVC insulated unsheathed multistranded copper conductor cable of 2.5 sqmm , cut to size all as required for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only FRLSH PVC insulated unsheathed multistranded copper conductor cable of 4.0 sqmm , cut to size all as required at site for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

Supply only FRLSH PVC insulated unsheathed multistranded copper conductor cable of 6.0 sqmm , cut to size all as required at site for carrying out repairs under relevant item No. 147.00 above complete all as specified and as directed by the Engineer-in-Charge.

JASOL MAA ENTERPRISES (BID ID -3496957)

M/s Shri Inder Construction Company (BID ID -3495859)

M/S MAYA CONSTRUCTION COMPANY (BID ID -3504713)