Reinvited for Annual repair estimate for Post Martum Office Building in PGIMS Rohtak Provl Div No 4 Rohtak Admn Block in VC Office Main College Indira Gandhi Vidya Bhawan Psychiatric wing Mental ward Basic Sciences Cancer Ward State Institute of Ment

Amount

Dismentaling cement conglomerate /terrazzo floors 25 mm to 50 mm thick without concrete base (HSR 8.26)

Scraping cement plaster(HSR.8.32 c)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR.11.7)

Conglomerate floor 40 mm thick cement concrete topping 1:2:4,(HSR.14.9)

12 mm cement plaster 1:6 on walls (HSR 15.7)

10 mm thick cement plaster 1:4 under side of ceiling (HSR 15.52)

Cement pointing 1:2 deep variety on brick and tile work ( HSR 15.60)

Cement pointing 1:2 flush on flat brick flooring (HSR 15.71)

Painting one coat with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.7)

Painting one coat with plastic emulsion paint on walls on old wood work to give an even shade (HSR 16.31)

White washing one coat or subsequent coat (HSR 16.46)

White washing two coats (HSR 16.47)

Distempering with washable oil bound distemper (of approved manufacture)one coat on old distempered work (HSR 16.59)

Distempering with washable oil bound distemper (of approve manufacture) two coats on old distempered work.(HSR 16.60)

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on old work,one coat to give an even shade (HSR 16.62)

Providing two coat of exterior acrylic emulsion paint. ( HSR 16.79) (b) 1st quality

Commercial Hardwood such as hollock, champ, chikrassy & Chaplash etc ( Non-conferious timber other than teak confirming to IS specification No - 1003, Kiln seasoned) shutters with vertical styles & rails , as specified in the statement No ( I ) ( attached in the end of this chapter ) with 2 Nos. plywood panels of the specified thickness mentioned below tongued & grooved including the cost of iron hinges, screws, chocks /cleats stops etc. complete fixed in position excluding the cost of tower bolts and handles but including the labour for fixing the same (HSR 17.30) a) 35 mm thick (12 mm thick commercial plywood panel

b)30 mm thick ( 12mm thick commercial plywood panel )

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot pressesd, conforming to I.S.2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position). (HSR 17.93) a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (ii) 30 mm thick

(iii) 35 mm thick

Wire gauze fixed on chowkats with 25mm thick cover moulding of full width of commercial hard wood such as hollock, champ chikrassy and chaplash, etc., (Non-coniferous timber, other than teak, conforming to I.S. specification No. 1003, kiln seasoned). (HSR 17.33)

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (Non coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned)(HSR 17.36) (c) 4 mm thick (glazing area above 55 sq dm but upto 84 sq dm of each pane)