BMCTRD/NDRF/2025-26/BAR-09

Making 120mm wide bamboo foot bridge with 100mm Bholuka or Barua bamboo posts driven 120 cm to 180 cm underground 3 Nos. in each row and rows being 3m apart bholuka or Barua bamboo dham placed over the posts and tied with cane or wire , Bholuka or barua bamboo struts in each row both up and down stream, jati bamboo long gorhs closely packed and tied with dham. Single layer of mat placed over 75mm thick brush wood and tied with bholuka or Barua bamboo rail stand fixed in one side of the bridge etc. complete

Labour for dismantling all members of the timber bridge (excluding piles) with necessary scaffolding, jati bamboos, jumper ropes etc, complete and stacking them at suitable places as directed (all members will be under custody of the contractor till taken over by the department)

Supplying and driving timber piles of 25cm to 30cm diameter, dressed to heart wood including making length in every 30 cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar.) A) Using Sal Timber a)Portion of pile actually driven under ground meter

b) Portion of pile remaining above ground

Labour for fitting and fixing RSJ beam, Old CI saddle etc. in position including necessary scaffolding and fixing necessary bolts and nuts, painting two coats complete as directed (Tar-Steel paints to be supplied by the contractor at his own costs) (RSJ of size 400 mm x 140 mm) Wt @ 64.060 Kg / M

Supplying , fitting and fixing timber beam and bearing beam rectangular in size fitted MS etc. supplying spikes etc. as necessary and coaltaring two coats with best tar applied hot as directed (Rate is inclusive of cost of required quantity of tar) a) Using Sal timber , Bearing Beam

Sal Wood work including supplying , fitting and fixing complete with necessary M.S. bolts, nuts, nails, screw etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Wood a) Underssed in floor planks, collars, bracing, standards, wheel guards,struts and railings, runner belts, rail, posts etc

A) Using Sal Wood (b) In track way planks (alternate nailing to be done with decking in a seggragate way)

Wood work including supplying , fitting and fixing complete with necessary M.S. bolts, nuts, nails, screw etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) B) Using Azar/ Nahar/ Nageswar/ Zarul Wood Underssed in floor planks, collars, bracing, standards, wheel guards, struts and railings, runner belts, rail, posts etc

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. a) In Trackway portion.

20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness Composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. Case - I: By Manual Means Bitumen (S-90)

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (i) Private Land

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (i) Private Land

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (ii) For Grading II Material

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.(A) By Manual Means

Providing and laying interlocking concrete block pavement (M40) having thickness 80 mm as per technical specification clause 1504 including carriage (b) excluding Edge block /Edge restraints

Supplying, filling and laying in loose with Geo-textile bags of Type-A (1.30m x 0.70m) made of Geo textile non woven fabric sheets of 400 GSM manufactured from polyster/ polypropylene conforming to relevant ISO standard filled with specified sand/ silt from flood plain or adjacent char within a distance of 90 m of the work site including excavation,filling Geo bags with sand weighing 126.00 kg after filling, stitching themouth of the filled bags with polypropylene or polyster complete as per technical specifications and as directed. (ii) Without boat

Supply, Stitching and Laying of Non wooven Geo textile Fabric sheet of 400 gsm

Title Informatory Board with Logo as per MORD specifications and drawing. Two nos. 1.6mm thick MS sheet duly welded with 5mm thick steel plate on back on edges. The 4 nos. steel plate will be welded horizontally with 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. The 2 nos. steel plate will be welded vertically to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly welded to vertical tubes. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloue. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1