PROVN OF TOILET BLOCK AND FOOTPATH NEAR BLDG. NO 148 AND 150 AT SCV AND ADDN/ALTN TO ROOM NO 149, 164, 171 AND 177 OF BLDG NO P-94 AT HQ CC AND OTHER SANCTIONED WORKS UNDER GE (EAST) LUCKNOW

Amount

Excavating in trenches not exc 1.5 m wide and not exc 1.5 m in depth for foundation cable/pipe etc and getting out in soft/loose soil complete all as specified and directed.

Surface dressing not exc 15 cm deep in soft/loose soil complete all as specified and directed.

M&L for hard core broken bricks of gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15cm thick, water and rammed to a true surface complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundations filling, sub base and mass concrete filling, etc complete all as specified and directed

M&L for 75mm thick cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) as in sub-floors, sub-bases, etc. complete all as specified and directed

M&L for sand filling under floor spreading and levelling in layers not exc 25 cm thick for well ramming watering required complete all as specified and directed .

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete complete all as specified & directed.

M&L for brickwork with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in in CM (1:6) complete all as specified & directed.

Taking down cement plaster on brick walls / ceiling incl. raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed..

M&L for brick work with fly ash bricks, straight or curved on plan exc 6M mean radius, old size brick built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and as directed.

Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges in large patches as in roof covering complete all as specified and directed. Note:- opening of existing wind tie where required for taking down of AC sheet is included)

Dismantling wrought iron or mild steel work of any description compelete all as specified.

M&L 10 mm thick rendering in cement mortar 1:4 on brick work or concrete surfaces on other than fair face surface , surface finished even and smooth without using extra cement using waterproofing compound fair and complete all as specified.

M&L for rendering 15mm thick on fair faces of brick work in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed

M&L for rendering 15mm thick on other than fair faces of brick work in CM1:6, finished even and smooth without using extra cement complete all as specified and directed

M&L for rendering 10 mm thick in cm 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick rendering in cement mortar in CM (1:4) on ceiling finished even and smooth without using extra cement, complete all as specified and directed.

M&L for RCC 1:1½ :3 type A1(using 20 mm graded stone aggregate) as in foundations, footings, plinth beams; bases for columns, etc.complete all as specified and directed

M&L for RCC 1:1½ :3 type A1(using 20 mm graded stone aggregate) as in Column, pillars, piers, posts and struts etc complete all as specified and directed

M&L for RCC type B-1 (1:2:4) (using 20 mm graded stone aggregate) as on beams, cantilevers, lintel over 1.5 m span complete all as specified and directed.

M&L for RCC type B-1 (1:2:4) (using 20mm graded aggregate) as in slab supported on wall walls beams and columns in floors roof landings complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for TMT bars 10 mm dia and over for reinforcement cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, and binding with and incl MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-415 or Fe-500 complete all as specified and directed.

M&L for TMT bars of 6 to 8mm dia and over cut to lenth, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed

All as per item No 25 above but 5 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders etc complete all as specified and directed.

M&L for formwork to sides of concrete in foundations, footings, bases of columns, sides and soffits (if any) plinth beams, and similar work complete all as specified and directed

M&L for formwork to sides of concrete of pillars, posts, struts, piers, columns etc complete all as specified and directed

M&L form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab not exc 200mm thick complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing and rubbish off the premises complete all as specified and directed

S&F for vitrifield ceramic tiles 10mm thick (Square/rectangular) polished area of each tile exc 0.42 sqm but not exc 1.00 Sqm in floor etc laid over 15mm thick screed bed in CM (1:4) set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified and directed.

S&F of vitrifield ceramic tiles 10mm thick (Square/rectangular) polished area of each tile exc 0.42 sqm but not exc 1.00 Sqm as in skirting etc laid over 10mm thick screed bed in CM (1:3) set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8mm thick in vertcial surfaces of size exc 0.11 Sqm but not exc 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed.

S&F solid PVC wall Linning consisting of 5mm thick Plain single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame and PVC L-beading at top of wall lining, opening eadge of door & windows as per specifications and drawing complete all as specified and directed.

S&F 5mm thick PVC sheet fillets of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified

S&F false ceiling with 4mm thick E-board white prepainted designer ceiling board of approved texure fixed with GI imposed grid frame work of size not more than 600x600mm having 24mm wide T-section runner made of 0.33mm GI sheet and angle made of 0.45mm, GI sheet suspected with 4mm dia GI wire complete all as specified and directed. Note. All exposed surface of grid work shall be powder coated white.

M&L for 16 to 18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window -cills, cooking platforms, partition of urinal and like pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding of edge laid over 15mm thick screed bed in CM (1:6) including rounding of edge of stone slabs one edge complete all as specified and directed.

S&F solid PVC moulded door frame of size 50mm x 47mm made out of 5mm prelam coloured PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet as reinforced with MS square tube and fixing in opening as specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick, (styles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam (Nut Brown colour ) PVC sheet on the front face & 2mm prelam (Nut Brown colur ) PVC sheet on back face, and fixing inthe frame at site as per specification and drawing on page 161 of SSR (Part -II ) 2010 complete all as specified and directed.

S&F steel window / ventilator glazed and gauged (combination) with side hung / top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame including guard bars and necessary cooler arrangement in window complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of apertature 1.40mm and fixed with tinned tacks or stainless steel wire staples all as specified and directed.

S&F of sheet glass 4mm thick,ordinary quality and glazing with aluminium snap beading in squares not exc 0.5 sqm in each pane complete all as specified & directed.

S&F of 3mm thick figured glass, pin head type and glazing with oil putty in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F 100mm butt hinges stainless steel with galvanised mild steel hinge pin anodised ISI marked and fixed, complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section all as specified and directed.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 15mm GI water tubing( Concealed type), medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F 20mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F 1000 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

S&F ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of 20mm dia and fixed (minimum weight 210 gms) complete all as specified and directed

S&F tubular towel rail, chromium plated brass 20mm dia 'D" type 60cm long between flanges complete all as specified and directed.

S&F PVC valve less, syphonic action type flushing cistern, 10 Litre capacity, low level, white with inlet, ball vlave float, handle including PVC rigid pipe 32mm bore as flush pipe fixed on walls by drilling holes and using PVC rawl plug of suitable size complete all as specified and directed.

S&F wash hand basins oval shaped vitreous china, coloured flat back size 550 x 400mm fixed including bracket embedded in granite stone complete all as specified and directed.

S&F CP grating doom 100 mm dia chromium plated complete all as specified and directed

S&F, glass corner self assembly, fancy type, made of 6 to 7mm thick toughened glass of size 250x250mm, fixed with CP brackets, all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in copings, bed plates, plinth courses, parapets and the like including weathering, slightly rounded or chamfered angles and throating including use and waste of necessary form work etc complete all as specified & directed

S&F 15 mm bore dia of pipe pillar taps fancy type cast copper alloy with capstan heads chromium plated screwed down hidh pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed

S&F 15mm bore cast copper alloy chromium plated bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

S&F angle valves 15mm bore , cast copper alloy chromium plated with long sunk and cap (Concealed type), screwed down high pressure screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F PVC connection, heavy duty 15mm bore, 45cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed.

S&F vitreous china wash down water closet pan pedestal pattern, including P or S trap and connection to drain (or outgoing pipe) and pvc seat cover excluding flushing cistern and flush pipe complete all as specified and directed

S&F plastic water closet seat,white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new PVC clamps complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new PVC clamps complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) reducers 75/110mm bore complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded aggregate for bed concrete to drain pipe packing under hunching for sides for 150mm dia SWG pipe lines completed all as specified and directed.

M&L for SWG drain pipe grade ‘A’ 150mm dia laid in trenches including jointing in CM 1:3 complete all as specified and directed.

S&F vitreous china urinals, half stall type (flat back), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including spreader, 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed

S&F 32 mm bore Low density PVC flexible pipe for Wash hand basin/sink etc complete all as specified and directed.

M&L for brushing neat cement slurry with 3.0 Kg./Sqm over roof slab complete all as specified and directed

M&L PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in roof padding/ roof kerbs / benching / coved fillets etc rounded or chamfered on edges, complete all as specified and directed.

M&L for roof/sunken treatment with polymeric water proofing mem breane with certain specification given below as under complete all as specified & directed (a) M&L plastering 10mm in CM 1:4 using 100% course sand on roof including WPC @ 3% by weight of cement. (b) Applying a coat of bitumenous primer @ 0.50 LTRs /Sqm and allow to dry (c) Applying a coat of hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm. (d) Supply and laying APP based polymeric water proofing membrane, weight not less than 3.00 kg/sqm and and minimum 3 mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) sealed the side laps with spread temper (e) applying a tack coat of hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm

Returning filling in including spreading levelling watering and well ramming in layer not exc. 25 thick complete all as specified and directed.

Removing excavated materials not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M&L for preparation of new plastered surface of wall including wall care putty 2-3mm thick and applying two coats of oil emulsion distemper (OBD) over a coat of primer complete all as specified and directed.

M&L for complete removal of exiting treatment and applying two coats of oil bound distemper over one coat of wall care putty of wall including preparation complete all as specified and directed

M&L for preparation of new or previously untreated wood and wood based surfaces of any description not otherwise descriped over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description over 10CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of newly plastered wall surfces and applying three coats of white wash complete all as specified and directed.

M&L for applying two coats of weather proof acrylic emulsion paint over a coat of 1mm thcik wall care putty & including a coat of emulsion wall primer all as per manufacture's instructions complete all as specified and directed

M&L for preparation newly plastered ceiling surfaces and applying three coat of white wash complete all as specified and directed.

S&F in repair health faucet (ABS body ) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

M&L for 75mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in floors / pavings complete all as specified and directed.

M&L ultra designer Indora matte finished chequered cement concrete tiles 30cm x 30cm 25mm thick reflective type with heavy duty, set, jointed and pointed in neat cment slurry in floors with grey cement and pigments over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) including iron mongery and cutting holes for hold fasts & making good complete all as specified & directed.

S&F of Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

S&F powder coated alumium glazed window shutter sliding type using 1.80 mm thick aluminium open three track section having size of style & top rails 83x44mm, bottom rils 100x44mm including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading screws, anodised aluminium fittings complete and glazing shall be done by using 5mm thick plain sheet glass complete all as specified and directed.

S&F powder coated aluminium grill (opening of gril not more than 100x100mm) fixed to windows or ventilators with anodised aluminium U channel 25x12mm size complete all as specified and directed.

Removing existing roof treatment and preparing surfaces to the entire satisfaction of Engr-in Charge /GE including taking down existing plaster,cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc . flushing at junction of parapets complete and removing the same to the places complete all as specified and directed.

Prepare Vatta / Coving of 25 mm to be done at all junctions of horizontal and vertical surfaces with polymer modified 1:3 Cement mortar containing Nitobond SBR Latex- Mortar and Screed modifier cum bonding agent at the rate of 3 litres per bag of cement. complete as per site requirenment and direction of Engineer-incharge complete all as specified & directed. Properties Typical mechanical properties of 1 : 3 cement sand mortar at W/C - 0.45 for control and W/C - 0.35 for mortar containing Fosroc Nitobond SBR (Latex) ( 3 litre / 50 kg cement ). Tested in accordance with BS 6319 & wet cured. Specific Gravity 1.015 to 1.040 @ 27⁰C Mechanical properties Control Nitobond SBR Latex Compressive strength (N/mm2) 3 days 11.5 -12.5 7 days 13.0 - 14.5 28 days 22.0 - 24.0 Tensile strength (N/mm2) @ 28 days 2.5 - 3.5 Flexural strength (N/mm2) @ 28 days 5.0 - 6.5

Waterproof coating: Providing and applying waterproofing treatment to sound, moisture free concrete surface using Nitoproof 600PF manufactured by Fosroc Chemicals India Pvt Ltd. Nitoproof 600PF shall be liquid applied single component pitch free polyurethane coating capable of bridging substrate cracks up to 2 mm. It shall be applied in two coats at coverage rate of 2kg/sqm. The membrane formed shall confirm to following minimum properties: 1) Elongation : >400% as per ASTM D412 2) Tensile Strength : 2.5 N/mm2 as per ASTM D 412 3) Adhesion in-peel test : >50 N as per ASTM C- 836 4) Recovery from 350% elongation : 95% as per ASTM D 412 5) Water Vapour Transmission 2.3mm film: 0.6 g/m2/hr 6) Initial Hardness Shore A : min 60 as per ASTM D 2240 7) Root resistant : protection screed required No geotextile recommended in between layers as it decreases elongation property of material Membrane Termination shall be done 300 mm above floor level. System includes supply, Surface preparation (crack treatment, coving etc), application and termination of coating all complete as per the fosroc methodology.

Suppyling, installing, testing and commissioning of 16 M high Mast system including 4 Nos luminaires & withb the following spacifications:- (a) Supply installation testing and commission of high mast shaft shall be in Two section hot dip galvanized , inside and outside in single dip, suitable for wind velocity as per IS:875 Part-3. There shall be only one longitudinal seam section and no circumferential weld. it shall also include accessories for high mast including head frame, 2 point suspension system with steel wire roop 6 ,, dia (97/19 constrution) gauge duble drum winch, galvanized lantem carriage arrangement suitable for up to 8 liminaires symmetrically tighting final & integral power tool for raising and lowering operation of the high mast. (b) Supply and fix of foundation bolts manufactured from special steel alongwith nuts,washers, anchor, plates & templates . (c) Supply and fix of LED light fitting 1x150 watt complete set-06 Nos (d) Supply and fix of twin dome aviation obstruction lights of type BJAOL 1 with Neon lamp of (e) Supply of control panel housing suitable control circuit for automatic switching ON and OFF of the MAST. It shall also have suitable control for operation of power tool. (f) Construction of suitable shallow foundation with M 20 grade concrete for the high mast considering the safe soil bearing capacity at site as 10 T/Sqm at 2 mtr depth with all materail and labour. (g) Eraction of the high mast with help of suitable equipment and wiring of luminaires with all wiring materail and labour. (h) Provision of GI electorde 60cm x 60 cm x 6mm earthing for high mast with earthing lead with 4 mm GI wire complete . (j) Installation of control panel on suitable foundation including all materail and labour (k) Testing and commissioning of above high mast system.

Shifting, refixing installing, testing and commissioning safe of exiting high mast lights 15 mtr height,Refixing at new location complete high mast lights with new fittings with help by crane and manual inculding control panel installing, testing and commissioning of 15 M high Mast system incl necessary excavation, PCC foundation as per drawing of exiting company manufacturer suitable drawing including necessary nuts & bolts the following spacifications:- (a) Shifting,Installation testing and commission of high mast shaft shall be in Two section hot dip galvanized , inside and outside in single dip, suitable for wind velocity . There shall be only one longitudinal seam section and no circumferential weld. it shall also include accessories for high mast including head frame, 2 point suspension system with steel wire roop 6 ,, dia (97/19 constrution) gauge duble drum winch, galvanized lantem carriage arrangement suitable for up to 8 liminaires symmetrically tighting final & integral power tool for raising and lowering operation of the high mast. (b) Supply of foundation bolts manufactured from special steel alongwith nuts,washers, anchor, plates & templates . (c) Supply of LED light fitting 1x150 watt complete set-06 Nos (d) Supply of twin dome aviation obstruction lights of type BJAOL 1 with Neon lamp of (e) shifting of exiting control panel,refixing , commissioning and testing at new location of control panel housing suitable control circuit for automatic switching ON and OFF of the MAST. It shall also have suitable control for operation of power tool. (f) Construction of suitable shallow foundation with M 20 grade concrete for the high mast considering the safe soil bearing capacity at site as 10 T/Sqm at 2 mtr depth with all materail and labour. (g) Eraction of the high mast with help of suitable equipment and wiring of luminaires with all wiring materail and labour. (h) Provision of GI electorde 60cm x 60 cm x 6mm earthing for high mast with earthing lead with 4 mm GI wire complete

Supply, laying, jointing, testing and commissioning in replacement of 70Sqmm 3.5 Core cable XLPE insulated , armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, laid in trenches, on pole complete all as specified and directed

Supply, laying, jointing, testing and commissioning in replacement of 50 Sqm 3.5 Core cable XLPE insulated , armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, laid in trenches,on pole complete all as specified and directed

Supply, laying, jointing, testing and commissioning in replacement of 16 Sqm 4.0 Core cable XLPE insulated , armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, laid in trenches,on pole complete all as specified and directed

M&L for earthing including eath work complete with galvanised steel earth plate electrode 60x60x6.0mm thick burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with to edge of the plate not less than 1.5 Mtrs below normal ground level connected to galvanised earth lead 32x6mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel protected by GI pipe all as shown in electrical pate No 5 of SSR Part I - 2009 connected to earthing test point all as specified and indicated including excavation earth work PCC chamber RCC chamber cover protection pipe watering pipe funnel and testing on completion all as specified and directed. (Note: Earth strip and protection pipe upto 7.50 m length is included in the unit rate)

Supply and fix cast aluminium heavy pole designer leg and border designer base finished with polyurethane paint (with prior treatments) diamtr of one leg is approx 76mm outer dia for spiogot entry 60mm 03 Nos "T" shaped bolts with nuts and washers provided for concrete foundation , total length of the pole incl base and legs (base x 03 Nos legs) is 2463 MM (Appx 8 fit 1 inch ) with fully cast aluminium finish polurethane paint( with prior tretments) suare junction with max projection breadth of 625 mm suitable for two number post top lantren with polyurethane ( with prior treatments ) Paint with arylic window cover total length 533 mm and breadth 228 mm.B-22 brass provided with qaluminium cover incl PCC 1:2:3 (size 600 x 600 x 600 mm ) foundation, , nut bolts, connecting up complete all as specified and directed.

Supply and fix LED city cube bollard light fittings 09 Watt, robusty designed IP 65/IK 10 bollard and and is easy to install with base plate incl PCC 1:2:3 (size 90 x 90 x 90 mm )incl connector block , nut bolts, connecting up complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 4 sqmm 2.0 core complete all as specified and directed.

Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable for under ground cable complete all as specified & directed. i.e 18 cm punned down thick shall be considerd for mesurement) complete all as specified and directed

M&L old size sub class 'B' bricks,laid flat in trenches over the cable with length of brick perpendicular to the direction of the cable, adjacent/abutting each other complete all as specified and directed

Taking down carefully copper/aluminium point wiring (light, fan, socket , bell or power) complete including all electrical fittings & fixtures (DBs,submain,cables etc) complete all as specified and directed

Taking down carefully Ceiling fan/wall fan/Exhaust fan complete including all electrical fittings & fixtures etc) complete all as specified and directed

Taking down carefully any Light fittings/fixtures any size complete including all (electrical fittings & fixtures etc) complete all as specified and directed

Material and Labour for point wiring complete with 1.5 sqmm (nominal area) FRLS grade PVC insulated, unsheathed multi stranded copper conductor single core cable 1100 volts grade in and including PVC conduit with accessories including 1.5 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor and connected to common earth dolly for One light/Ex-fan point controlled by one switch 5Amps SP all as specified and directed. Note :- Sunken box/cover plate for modular switches, sockets etc will be measured and paid seperately under relevant items and blank plate required if any will be deemed included in the item rate.and making good disturbed surfaces of wall , floor etc and matching wth original colour of wall complete all as specified and directed

All as per Item No 115 hereinbefore but for one 5 A socket outlet on independent board

All as per Item No 115 hereinbefore but for one 5 A socket outlet on same board

All as per Item No 115 hereinbefore but point wiring complete with 2.5 sqmm for 3 pin 15 A socket outlet on independent board including 2.5 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor

Supply and fix frame plate with match cover one module plate complete all as specified and directed

Supply and fix frame plate with match cover two module complete all as specified and directed

Supply and fix frame plate with match cover three module complete all as specified and directed

Supply and fix frame plate with match cover four module complete all as specified and directed

Supply and fix frame plate with match cover six module complete all as specified and directed

Supply and fix frame plate with match cover eight module complete all as specified and directed

Supply and fix frame plate with match cover twelve module complete all as specified and directed

Supply and fix terminal box suitable one modular plate of size 75X75x50 mm including cutting, grooving and plastering etc. complete all as specified and directed

Supply and fix terminal box suitable two modular plate of size 75X75x50 mm including cutting, grooving and plastering etc. complete all as specified and directed

Supply and fix terminal box suitable three modular plate of size 100X75x50 mm including cutting, grooving and plastering etc. complete all as specified and directed

Supply and fix terminal box suitable four modular plate of size 128X75x50 mm including cutting, grooving and plastering etc. complete all as specified and directed

Supply and fix terminal box suitable but six modular plate of size 210X75x50 mm including cutting, grooving and plastering etc. complete all as specified and directed

Supply and fix terminal box suitable eight modular plate of including cutting, grooving and plastering etc. complete all as specified and directed

Supply and fix terminal box suitable twelve modular plate of including cutting, grooving and plastering etc. complete all as specified and directed

Supply and fix Modular switch one way 6A 230V AC 50 HZ SP one module complete all as specified and directed

Supply and fix Modular switch one way 16A 230V AC 50 HZ SP one module complete all as specified and directed

Supply and fix Modular socket 2/3 pin combined 6A 230V AC 50 HZ SP two module complete all as specified and directed

Supply and fix Modular socket 6A/16A 2/3 pin combined 230V AC 50 HZ SP two module complete all as specified and directed

Supply and fix Modular Regulator 230V AC 50 HZ SP two module complete all as specified and directed

S&F modular bell push single pole 1 module6 Amp, 240 volt complete all as specified and directed

S&f call bell , ding dong / musical AC single phase 230 volts complete all as specified and directed

Supply and fix in repair of MCB DB SPN 8 way double door type suitable for TP/FP including necessary dummy plate and necessary civil works complete all as specified and directed

Supply and fix MCB SP 230V, 6-32 Amps capacity complete all as specified and directed

Supply and fix MCB SPN 230V, 32 to 63 Amp capacity complete all as specified and directed

S&F ceiling rose PVC polycarbonate complete all as specified and directed

Supply and fix PVC pipe 25 mm dia for protection of cables complete all as specified and directed

Supply and fix PVC pipe 80 mm dia for protection of cables complete all as specified and directed

Supply and fix TV Socket 1 Module Modular complete all as specified and directed

Supply and fix telephone socket 1 Module complete all as specified and directed

Supply and fixing in repair decorative LED lighting fixture with extruded Al. heat sink, environmental friendly, energy efficient ready to use suitable for 4’ LED tube complete all as specified and directed .

Supply and fixing LED T8 IP 20 linear tubular lamp 20 watt(4') double end with and PC diffuser complete with inbuilt driver complete all as specified and directed

S&F Engagement light with set of three light (Red,yellow, and green light) with insulated body with back plate suitable for batten fittings as directed including 1.5 sqmm 3 core cable for connection all as specified and directed.

S&F 2X2 36 Watt Ceiling light fittings ( with one extra driver each light) exquisitely designed luminaire smart glow which is bound to deliver extra lumen through its pure form and glare-less light recessed full open (120 lumen/watt) complete all as specified and directed

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed

Supply and fixing Wall fan complete with all accessories, 230 V, 400 mm sweep. complete all as specified and directed

S&F in replacement decorative wall mounted fancy light fitting made up of brass rubi lamp brand double handed item code 119598240 including of thred type bulb of 9-15 watts covered by glass complete all as specified and directed

Cutting chases in concrete wall/stone for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 20 cm girth and matching wall color complete all as specified and directed

Material and Labour for Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 4 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 4 Sqmm drawn through & including PVC Conduit pipe 20 mm dia with all fittings complete all as specified and directed

Material and Labour for Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 6 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 6 Sqmm drawn through and including PVC Conduit pipe 20 mm dia with all fittings complete all as specified and directed

Supply and fix single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one 20 amps SPN MCB complete all as specified and directed

S&F modular metal flush box 12 module complete all as specified and directed

S&F modular metal flush box 08 module complete all as specified and directed

S&F modular metal flush box 03 module complete all as specified and directed

Supply and fix LED tube light fittings 1200 mm,20 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminum housing enviromental friendly, energy efficient complete all as specified and directed.

Supply and fix LED tube light fittings 600 mm, 10 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminum housing enviromental friendly, energy efficient complete all as specified and directed.

S&F exchust fan PVC body 300mm sweep, 230 volt single phase silent proof,

Supply and fix SPN MCB DB 8 ways with 200 Amps rated bus bar 240Volt, Double door type all as specified

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 4.0 core complete all as specified and directed.

Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable for under ground cable complete all as specified & directed. i.e 18 cm punned down thick shall be considerd for mesurement)

S&F gum metal with iron wheel hand, screwed both ends complete for size 25mm bore including connecting excavation

S&F gum metal with iron wheel hand, screwed both ends complete for size 20mm bore including connecting excavation

M&L for cutting GI Pipes and reducing to required length of dia 40 mm bore and inserting Tee 25x 25x 20 mm GI pipe incl nessasary excavation complete all as specified and directed.

M&L and including earth work construction of valve chamber with inner clear dimension 600 x 600 x 600 mm suitable for 50mm Gate Valves with PCC (1:4:8) 150mm thick type D2 for foundation, Brick masonary 230mm wall in CM (1:4), PCC (1:2:4) 75mm type B1 for coping, rendering in CM (1:4) 15mm thick including provisiion of 3 mm thick MS sheet cover and 25 x 25 x 3mm angle frame embeded in coping with two coats of synthetic enamel paint over a coat of red oxide primer with locking arrangements including necessary earth work complete all as specified and directed .

QUALITY CONSTRUCTIONS CO

ANIL CONSTRUCTION

M/S S S A ASSOCIATES