REPAIRS TO JOINERY, ROOFING, FALSE CEILING, FLOORING, PLASTERING, PLUMBING, SANITARY FITTINGS, PERIODICAL SERVICES AND OTHER CONNECTED MAINTENANCE WORKS AT MILITARY HOSPITAL, RASHTRIYA MILITARY SCHOOL, GE OFFICE UNDER GE BELGAUM

Amount

Taking down chowkhat with shutters (without taking off shutters from the frame) area not exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Taking down shutters of any description n exc 1 sqm each all as specified and directed.

Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in surface channels, drains, etc. including necessary form work/ moulds including demolition of existing plain cement concrete of any description and size and making good disturbed surfaces all as specified and directed.

M&L plain cement concrete 1:2:4, type B0, using 12.5mm graded stone aggregate as in roof kerbs, mud stops, coving, etc. with rounded or chamfered edges including demolition of existing plain cement concrete of any description and size and making good disturbed surfaces all as specified and directed

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5 mm graded stone aggregate and setting in CM 1:6 including demolition of existing unserviceable PCC block masonry built in cement mortar in any position below or above ground level and making good disturbed surfaces all as specified and directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work including dismantling of existing unserviceable timber scantling 40 Sq.cm and over in section and in any position in un-framed work and making good disturbed members all as specified and directed.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or beads; sectional area exc 6 and n.exc 13 Sq.cm including dismantling of existing unserviceable fillets, rails, posts, rafters, purlins, etc. and making good disturbed members all as specified and directed.

M&L for 2nd class hard wood board, 20mm thick, planned on one side and the other clean sawn, with butt joints and fixed with nails in any situation including dismantling unserviceable boarding of any description and making good disturbed members all as specified and directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 30mm thick 2nd class hard wood glazed/ gauged shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 30mm thick 2nd class hard wood glazed/ gauged window/ ventilator shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) and fitted to chowkats all as specified and as directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides covered with teak wood lipping, fitted to chowkats all as specified and as directed.

M&L for 18mm thick prelaminated particle board as in cupboard shutters, interior grade, prelaminated one side with decorative choice lamination on the other side with white lamination as in cup boards, shelves, cabinets, panels, etc fixed with screws all as specified and directed

M&L for aluminium frame work as in doors, partitions, windows and ventilators using powder coated aluminium sections including provision of glazing clips, hinges, handles, etc including taking down existing aluminium joineries of any description all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary gaskets. (iii) Particle board/ glass panels/ wire mesh shall be measured and paid separately.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on both sides reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F stainless steel butt hinges 100mm in size, medium weight, bright polished all as specified and directed.

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F MS butt hinges 75mm in size, medium weight, cold rolled all as specified and directed.

S&F in repairs MS butt hinges 75mm in size, medium weight, cold rolled all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F aluminium anodised barrel tower bolt 100mm size all as specified and directed.

S&F in repairs 300mm long mild steel helical door spring, ordinary rat tail pattern spring, including roller and roller plate complete all as specified and as directed.

S&F aluminium handle, 'D' type, anodised 150 mm in size all as specified and directed.

S&F in repairs aluminium handle, 'D' type, anodised 125 mm in size all as specified and directed.

S&F in repairs 100mm long aluminium anodised hasp and staple, safety type with hinge pin including bolt to hinge plate fixed with screws complete all as specified and as directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F in repairs 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F 100mm size mortise lock, brass, vertical type, four levers, including cutting holes in existing pressed steel frames, all as specified and directed. Make: Godrej or equivalent.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs 25mm dia mild steel powder coated curtain rods with fancy ends, fitted to brackets with necessary screws all as specified and directed. Make: MARVEL or equivalent

S&F in repairs stainless steel brackets, suitable for holding 25mm dia single curtain rods, fixed to wall with necessary screws including drilling and plugging the holding screws and making good the wall surfaces all as specified and directed.

S&F in repairs floor door stopper of aluminium body and tongue, anodised, with 140mm long cover plate and hard drawn steel spring, fixed in floor all as specified and directed.

S&F in repairs Door closer, of aluminium (die cast) body, hydraulically regulated, designation No 3, universal type, suitable for door shutters of weight between 61 to 80kg, all as specified and directed

S&F in repairs Door closer, of aluminium (die cast) body, hydraulically regulated, designation No 2, universal type, suitable for door shutters of weight between 36 to 60kg, all as specified and directed

S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and directed

M&L for mild steel small articles like bands, straps, including bolts, if required; hooks (stay), hook and pintle hinges; large hasps and staples; hand made sliding bolts; clamps; hold fasts; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar articles conforming to Fe-290 Gde-E-165 fixed in repairs all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 fixed in repairs all as specified and as directed.

S&F mild steel works in tubular trusses, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 fixed in repairs all as specified and as directed.

M&L for Mangalore pattern or similar tiles in roofing, interlocking at side joints, laid dry, including dismantling of existing unserviceable tiles of any description and size and making good disturbed roof members all as specified and as directed.

Dismantling of existing single layer Mangalore pattern or similar roofing tiles interlocking at side joints, laid dry and re-laying the same in new or old position and making good disturbed roof members all as specified and as directed.

M&L for ridge/ hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in CM 1:6 including dismantling of existing unserviceable ridge tiles of any description and size and making good disturbed roof members all as specified and directed.

M&L for 6mm thick asbestos cement corrugated or semi-corrugated sheets in roofs, walls, etc. fixed with L-type or J-type or cranked hook bolts including dismantling of existing unserviceable AC roofing sheets of any description and size and making good disturbed roof members all as specified and directed.

M&L for 6 mm thick asbestos cement two piece adjustable serrated ridge for corrugated sheets in roofs fixed with ‘L’ type or ‘J’ type or cranked hook bolts including dismantling of existing unserviceable AC ridge sheets of any description and size and making good disturbed ridge/ roof members all as specified and directed

S&F pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.45mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions including dismantling of existing unserviceable corrugated roofing sheets of any description and size and making good disturbed roof members all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F corrugated galvanised mild steel sheeting with grade of zinc coating 275, 0.63 mm thick, with two corrugation side laps in roofs, walls, etc. fixed with L-type or J-type or cranked hook bolts including dismantling of existing unserviceable CGI roofing sheets of any description and size and making good disturbed roof members all as specified and as directed.

S&F plain galvanised mild steel sheeting with grade of zinc coating 275, 0.8mm thick, in ridges, hips, valley gutter, drip and straight flashings including dismantling of existing unserviceable PGI sheets of any description and size and making good disturbed roof members all as specified and directed.

M&L for 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap in roof, wall etc fixed with L-type or J-type or cranked hook bolts including dismantling of existing unserviceable corrugated roofing sheets of any description and size and making good disturbed roof members all as specified and as directed.

S&F PVC (SWR) eaves gutter half rounded 150mm bore including pipe accessories PVC holder bats bolts nuts etc. including taking down existing unserviceable gutters of any description and size and making good disurbed surfaces all as specified and directed.

M&L for providing roof treatment with APP modified water proofing membrane with the following specifications all as specified and directed.

Removing existing roof/ chajjas treatment of any type like plastic felt/ HP tiles of any description including taking down existing plastering/ concrete of any thickness and cleaning the top surface of RCC slab with wire brush including removal of debris outside of MOD premises

Brushing with neat cement slurry @ 3Kg/Sqm on cleaned RCC slab surfaces and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement. Note: Water proofing compound shall be measured and paid separately

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.3 litre per Sqm & providing APP modified water proofing membrane 4mm thick and weight not less than 4.5kg/ sqm reinforced with non oven polyester mat weight not less than 160gms per Sqm including minimum 10cm side/ over laps & including applying a coat of blown hot bitumen grade 85/25 over membrane at 1.2kg per Sqm & on drying applying a coat of solar reflective bituminous aluminium paint at 0.1kg/sqm.

NOTE: APP modified water proofing membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given IS 16540-2017/ IS 16532-2017. Contractor shall produce necessary test certificate of the manufacturer to the Engineer-in-charge before incorporation in the work. Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminium anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling including dismantling of existing unserviceable false ceiling boards of any description and size alongwith snap grid frame works including making good disturbed wall/ ceiling surfaces all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in sub base for flooring including finishing the surface fair and even and demolition of existing cement concrete sub base/ floor of any description and making good the disturbed surfaces all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:2:4 type B2 using 40mm graded stone aggregate as in paving, hard standing etc. and finishing the concrete surface even and smooth with using extra cement and making impressions of expanded metal while the concrete is green and demolition of existing cement concrete floor of any description and making good the disturbed surfaces all as specified and directed.

M&L for coloured non skid ceramic tiles, 7mm thick, area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 including dismantling of existing unserviceable tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for coloured glazed ceramic tiles 300mm x 450mm x 7 to 8mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 including dismantling of existing unserviceable tiling alongwith cement plaster and removing rubbish off the premises all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 15mm thick screed bed in cement mortar 1:4 including dismantling of existing unserviceable tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 including dismantling of existing unserviceable tiling alongwith cement plaster and removing rubbish off the premises all as specified and directed.

M&L for machine cut Granite stone tiles, 20mm thick, premium quality, any colour, as in flooring, set and jointed with neat cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab over20mm thick screed bed in cement mortar 1:4 including rubbing and polishing including dismantling of existing unserviceable stone tiles alongwith cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed.

M&L for machine cut Granite stone tiles, 20mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the tiles including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 including dismantling of existing unserviceable stone tiles alongwith cement mortar plaster and removing rubbish off the premises all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. including dismantling of existing unserviceable stone slab/tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for 60mm thick machine pressed precast concrete interlocking coloured paver blocks, M-35 grade, any shape and size with anti skid finish on top confirming to IS 15658-2006, including 75mm thick sand filling, watering, consolidation and dismantling of existing unserviceable paver blocks and removing rubbish off the premises all as specified and directed.

M&L for plain cement concrete 1:3:6, type C2, (Using 40 mm graded stone aggregate), 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. including demolition of existing plain cement concrete plinth protection of any description and thickness and making good disturbed surfaces all as specified and directedall as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on soffit of roof ceiling, finished fair and even without using extra cement complete complete all as directed.all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1:4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry surfaces finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound all as specified and as directed.

M &L for 5mm thick sheet glass ordinary quality and glazing in square n exc 0.5 sqm in each pane all as specified and directed.

M & L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each pane including hacking out old broken glass of any description and size and making good disturbed surfaces all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for one coat of white wash on old decorated surfaces of walls, pillasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for one coat of white wash on old decorated surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for one coat of oil bound distemper (Acrylic distemper washable), any colour, on old distempered walls, pillasters, cornices, etc., including necessary preparation of surfaces by washing, rubbing down and stopping all as specified and as directed.

M&L for one coat of cement based paint on old cement painted walls, pillasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of cement based paint, any colour, on newly plastered surfaces of walls, pilasters, cornices, etc., over a coat of alkali resistant primer including necessary preparation of surfaces all as specified and directed.

M&L for one coat of weather proof exterior emulsion paint on old decorated surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces by washing, rubbing down and stopping all as specified and as directed.

M&L for two coats of weather proof exterior emulsion paint on old decorated surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces by washing, rubbing down and stopping all as specified and as directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

S&F in repairs 1000 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including testing and provision of 20mm dia brass ball valves high pressure with high density plastic float and fly nuts screwed for iron pipe complete all as specified and directed.

S&F 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable PVC/ GI tubes of any grade and making good disturbed surfaces all as specified and directed.

S&F 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable PVC/ GI tubes of any grade and making good disturbed surfaces all as specified and directed.

S&F 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable PVC/ GI tubes of any grade and making good disturbed surfaces all as specified and directed.

Fixing only in repairs 15mm bore galvanized iron tubes, any grade, with all new fittings, fixed complete to walls, ceilings or laid in floors and making good disturbed surfaces all as specified and directed.

Fixing only in repairs 20mm bore galvanized iron tubes, any grade, with all new fittings, fixed complete to walls, ceilings or laid in floors and making good disturbed surfaces all as specified and directed.

Fixing only in repairs 25mm bore galvanized iron tubes, any grade, with all new fittings, fixed complete to walls, ceilings or laid in floors and making good disturbed surfaces all as specified and directed.

S&F in repairs 15mm bore bib taps, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs pillar taps, brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S & F in repairs 15 mm bore Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 15mm bore PTMT bib taps, standard type, (Minimum weight 90gms) any colour, high pressure screwed for iron pipe all as specified and as directed.

S&F in repairs 15 mm bore 2 way Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed. Make: Cat No. FUS 29041 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. ALD-CHR-565 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs 15mm bore stop valves, fancy type, brass CP, screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 15mm bore stop valves, fancy type brass CP, with long shank and cup (concealed type), screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 1mm thick stainless steel sink, overall size not less than 495x420mm, bowl size not less than 410x330x160mm, with plug, washers and wastes including bedding in cement mortar, fixing cantilever brackets and connecting union to pipe all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, fixing bolts, etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F in repairs plastic water closet seat for EWC, closed pattern with flat bottom and cover, any colour as approved by GE and mild steel chromium plated or aluminium hinging device all as specified and as directed.

S&F in repairs, Vitreous China urinal, bowl type, flat back/ corner wall, 465 x 355 x 265mm size (minimum), white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including provision of grating and union for discharge pipe, 15mm bore PTMT urinal spreader, waste pipe, (excluding flushing cistern, flush pipe) all as specified and as directed.

S&F in repairs PTMT waste couplings, half or full threaded, minimum weight 45 gms suitable for 32mm bore discharge pipes all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm, excluding taps, waste chain and plug and porcelain stopper but including brackets etc complete all as specified and directed.

S&F in repairs shower rose swivel type brass CP shower rose 125mm size suitable for fixing with 15mm bore pipe all as specified and as directed.

S&F in repairs PVC flexible pipe (waste pipe), 900mm long, suitable for 32 mm bore waste coupling of sink/ wash hand basin all as specified and directed.

S&F in repairs PVC flexible pipe (waste pipe), suitable for urinals all as specified and directed.

S&F in repairs stainless steel towel rail 600mm long with and including stainless steel brackets and chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F in repairs PTMT Towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats (Minimum weight 190gms) all as specified and as directed.

S&F in repairs vitreous china squatting pan, Orissa pattern, size 580mm x 440mm, white, with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap etc complete all as specified and directed.

S&F in repairs syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 750mm long all as specified and directed.

M&L for 40mm bore Ligh Density Polyethylene pipes (LDPE) of pressure rating 4 kgf/cm2 etc.fixed complete to walls, ceilings or laid in floors, fixed in repairs, all as specified and as directed.

M&L for 50mm bore Ligh Density Polyethylene pipes (LDPE) of pressure rating 4 kgf/cm2 etc.fixed complete to walls, ceilings or laid in floors, fixed in repairs, all as specified and as directed.

S&F 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down existing unserviceable pipes of any description and size and making good disurbed surfaces all as specified and directed.

S&F 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down existing unserviceable pipes of any description and size and making good disurbed surfaces all as specified and directed.

S&F 110mm bore UPVC (SWR) bends any radius all as specified and directed.

S&F 75mm bore UPVC (SWR) bends any radius all as specified and directed.

S&F 110mm bore UPVC (SWR) branch piece, single Y, equal or unequal with access door all as specified and directed.

S&F 75mm bore UPVC (SWR) branch piece, single Y, equal or unequal with access door all as specified and directed.

S&F 110mm bore UPVC (SWR) branch piece, double Y, equal or unequal with access door all as specified and directed.

S&F 110mm bore UPVC (SWR) vent cowl all as specified and directed.

S&F UPVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

S&F UPVC (SWR) gully trap 125/110mm, setting & jointing with solvent cement including taking down old one all as specified and as directed

M/S SAMARTH CONSTRUCTIONS

SHRI.H.R.PATIL

M/s A N Kalbhavi

SANJAY ELECTRICALS

ASHOK M RAJGOLKAR

M/s. N D KALING

DHANSHRI ENTERPRISES