SPL REPAIRS TO TOILET BLOCKS BLDG No. OWT-151, OWT-152 AND OWT-153 OF MH, PROVN OF ACCN FOR SENTRIES NEAR TOWER POST ALONG SOUTHERN BDY, PROVN OF BATHROOM WITH TOILET AND URINAL NEAR BLDG No. P-37 OF DIV AND PROVN OF CERTAIN REVENUE WORKS AT LIKABALI

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame), exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling/ Taking/ Lowering down unserviceable Water Storage Tank, exc. 250 Litre and not exc. 500 Litre Capacity after Disconnecting all existing Water Pipe Line Connections, complete all as specified and as directed.

Surface Excavation not exc. 30 Cm deep and ave. 15 Cm deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Post Holes (or similar Holes) in Soft/Loose Soil, each not exc. 0.50 Cum, getting out including spread and levelled with excavated surplus Soils, complete all as specified and as directed.

M&L Sand Filling (as approved) under Floors or in Foundations in layers not exc. 15 Cm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Hardcore broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) as in Coping, Bed Plates, Holdfast, Bed Block, Kerb Stones including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating, complete all as specified and as directed. NOTE : Cost of Formwork shall deemed to be included in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) for embedding of Mild Steel Post, etc. in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed. NOTE : Cost of Formwork shall deemed to be included in Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed. NOTE : Cost of Formwork shall deemed to be included in Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under reamed Piles, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Beams, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Chajjas, etc. complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and setting in Cement Morter 1:4, complete all as specified and as directed. NOTE : Reinforcement shall be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Chullah Hoods, Chajjas, Troughs and Similar Items including Edges, etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Openings in Concrete Walls, Floor and Roofs not exc. 20 Cm Wide and Sides of RCC/ PCC Bands in Walls, Horizontal or Sloping and Similar Work, exc. 5.0 Cm but not exc. 10 Cm Wide, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 40mm thick in Damp Proof Courses to Horizontal or Vertical Surfaces including mixing WPC and Use & Waste of Formwork and Applying evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) shall be Measured and Paid for separately under appropriate Item.

M&L Cutting Holes in Brick Walls, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to dismantled portion with Cement Concrete 1:3:6 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any No. Panels) Plain, Framed with Lock Rails with Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with Commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (Without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50x47mm made out of 5.0mm thick, Plain Colour PVC Sheet, reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails, Mild Steel Frame shall be covered with Heat Moulded Plain Color PVC ‘C’ Channel having a PVC Strip of 20mm width stuck inside with Solvent Cement for Stiles & Plain Color PVC Sheets for Top Rail, Lock Rail & Bottom Rail on Either Side & Gap insert for Top Rail & Bottom Rail, Paneling of Plain Color PVC sheet to be fitted in the Mild Steel Frame, welded/sealed to the Stiles & Rails with suitable PVC Sheet Beading & jointed together with Solvent Cement, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle, Steel Peg Stay, etc. with Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle, Steel Peg Stay, etc. without Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Steel Ventilator with Top Hung Shutter including Hinges with Steel Peg Stays, complete without Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt (as approved), 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge (as approved) 75mm in size, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge (as approved) 100mm in size, complete all as specified and as directed.

S&F Aluminium Handle (as approved) 150mm in size, anodised, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper having Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

M&L Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Figured Glass 4.0mm thick, Pin head type and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Rolled Mild Steel in Joist, Channel, Angle, or Tee Sections in Vertical Post, conforming to Fe-410-W (Gde E-250) Quality 'B', fixed independently, without Connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the Length indicated), complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'B', fixed with Angle Cleats or other Connecting Plates, complete all as specified and as directed

M&L Steel Work (Square/ Rectangular Hollow Section) in Tublar Trusses including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:0011-1979, Grade St-240, complete all as specified and as directed.

M&L Mild Steel Screw Bolts (machine made) of any description or Size, with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System having Snap Grid/ Frame Work of size 605x605mm with and including Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 100mm thick in Sub-base to Flooring, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Flooring, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Rubberised Mastic Flooring 40mm thick for Gas Godown and suitable for Loading and Unloading Gas Cylinders, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Flooring, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strips 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured/Designer Tiles 7.0mm to 8.0mm thick (Square/ Rectangular) Area of Each Tile exc. 0.06 Sqm but not exc. 0.11 Sqm (1st quality and/or as approved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/Designer Tiles 7.0mm to 8.0mm thick (Square/ Rectangular) Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality and/or as approved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 300x200x 6.0-7.0mm thick (1st quality and/or as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 350x250x6.0-7.0mm or 350x450x6.0-7.0mm thick (1st quality and/or as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Machine Cut Granite (of any type) Work 20mm thick (Table Rubbed and Polished) in Steps, Jambs, Pillars, Window Cills, Cooking Platforms and like in Cement Mortar 1:4 including Pointing in White Cement 1:2, using Marble Dust with Admixture of Pigment to match with Shade of Granite, fixing over and including Cement Screed Bed 15mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Machine Pressed Rubber Moulded Pre-cast Concrete Coloured Glossy Finished, Interlocking Polished Paver Block 60mm thick of M-35 Grade, with Grey Cement and Pigment of any shape and size (as ordered), conforming IS-15658-2006, ISI Marked, laid Dry over and including Sand Cushioning of 50mm thick and grouted with Clean dry Sand as in Floors, complete all as specified and as directed. NOTE : Cost of Clean Dry Sand will deem to include in Quoted Unit Rate.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick in Cement Mortar 1:4 in 2 Coats/ layers on Brick/ Pre-cast Cement Concrete Blocks or Concrete Works, Backing Coat/ layer of 10mm thick and Finishing/ Top Coat/ layer of 5.0mm thick including mixing WPC to Finishing/ Top Coat/ layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) shall be Measured and Paid for separately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Wall Care Putty 3.0mm thick in Two Coats on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain a Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (as approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Plastered/ Unplastered Surfaces of Walls by Complete removing Existing Surface Treatment and applying Two Coats of Distemper Oil Emulsion (as approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (as approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of Cement Based Paint (as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

M&L Refixing old Steel Tubing 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 1.006 here-in-before) in new or old position (Walls, Ceiling, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required at Sites), complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

M&L Refixing old Steel Tubing 20mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 1.007 here-in-before) in new or old position (Walls, Ceiling, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required at Sites), complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs (12 No.), complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) with Long Body, Cast Copper alloy, Chromium plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs (06 No.), complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Stop/ Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, with Long Shank and Cup Concealed, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs (30 No.), complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 15mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs (04 No.), complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs (04 No.), complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule, complete all as specified and as directed.

S&F PTMT Ball Valve 15mm bore (dia), having weight not less than 142 Grams, high pressure with Epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and Fixed-in-repairs (01 No.), complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of size 580x440mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (Nozzles of WC Pan) including Provision of Lime Concrete Bedding and Making Good to Floor/ Distrubed Surfaces and Fixed-in-repairs (12 No.), complete all as specified and as directed

M&L PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, a Pair of Cast Iron Brackets Erecting Stand duly Painted, including PVC Flush Pipe 32mm dia with PVC Long Bend, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs (12 No.), complete all as specified and as directed.

M&L Vitreous China White Wash Hand Basin of size 550x420mm, Oval Shape, Counter Top including Brass Chromium plated Waste Fitting 32mm bore (dia), a Pair of Cast Iron Brackets or Erecting Stand duly Painted, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 but excluding Taps, complete all as specified and as directed.

M&L Vitreous China White Wash Hand Basin of size 550x400mm, (Flat Back) including Brass Chromium plated Waste Fitting 32mm bore (dia), a Pair of Cast Iron Brackets or Erecting Stand duly Painted, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 but excluding Taps, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 450mm in length with PTMT Nuts for WHB and Fixed-in-repairs (12 No.), complete all as specified and as directed.

S&F Brass Chromium Plated Overhead Shower Rose 125mm with Shower Arm, Swival Joint including fixing to Steel Pipe and Fixed-in-repairs (06 No.), complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws and Fixed-in-repairs (06 No.), complete all as specified and as directed.

M&L PVC (SWR) Floor Trap having Diameter of Outlet in 75mm, Plain with Grating including Jointing with Solvent Cement and Fixed-in-repairs (04 No.), complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixing to Walls or laid in Floors and Fixed-in-repairs (8.00 RM), complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia), any radius with Access Door, etc. and jointing with Solvent Cement and Fixed-in-repairs (06 No.), complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl of Size 75mm (as approved), Jointed with Solvent Cement and Fixed-in-repairs (03 No.), complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixing to Walls or laid in Floors and Fixed-in-repairs (30.00 RM), complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl of Size 110mm (as approved), Jointed with Solvent Cement and Fixed-in-repairs (18 No.), complete all as specified and as directed.

S&F PVC (SWR) Branch Pieces 110mm bore (dia), Single (Single Y) Equal or Unequal with Access Door, jointing with Solvent Cement and Fixed-in-repairs (04 No.), complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches and Fixed-in-repairs (22.00 RM), complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Concrete Bed to PVC (SWR) 110mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and Tested; complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cutting into existing Manholes for Connecting New PVC (SWR) Pipe 110mm bore (dia), Making Good to Pipe and Rendering, Cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets, Light Fittings, etc., Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down/out unserviceable Sub-main Wiring from Batten/ Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 4.0 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable with 4.0 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed, Multi-stranded Single Core Copper Conductor FRLSH Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping shall deem to include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Casing Capping only. Wires required for looping, etc. (as ordered) shall deemed to be included in the Quoted Unit Rate.

S&F PVC Rectangular Block of size 100x100x50mm deep with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down/ out unserviceable PVC Block (03 No.), complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi Plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Dimmer Switch type, 230 Volt AC, Rotary Stepped Electronic, 120/280 Volt including necessary Connection and connecting up, complete all as specified and as directed.

S&F LED Lamp 7 Watt, 230 Volt (as approved) including Taking down/ out unserviceable Lamp of any description (18 No.), complete all as specified and as directed. MAKE : HAVELLS, Model : LED ADORE7 WE27 WW Ball Lamp or equivalent Model in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

S&F LED Bulk Head e-TATRA Series Light Fitting 1x6.0 Watt having Plastic Housing with Clear Prismatic Diffuser LED 6.0 Watt Lamp and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description (09 No.), complete all as specified and as directed. MAKE : C&S E-TARTA Series 6W or equivalent Model in Make : BAJAJ/ CG/ HAVELLS/ PHILIPS (as approved by GE).

S&F LED Bulk Head e-TATRA Series Light Fitting 1x10 Watt having Plastic Housing with Clear Prismatic Diffuser LED 10 Watt Lamp and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable, complete all as specified and as directed. MAKE : C&S E-TARTA Series 10W or equivalent Model in Make : BAJAJ/ CG/ HAVELLS/ PHILIPS (as approved by GE).

S&F LED Bulk Head, Metal Halied Light Fitting 1x10 Watt with LED 10 Watt Lamp and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable, complete all as specified and as directed. MAKE : C&S, Model : TARTA, Code : CG8OIB10WLED or equivalent Model in Make : BAJAJ/ CG/ HAVELLS/ PHILIPS (as approved by GE).

S&F LED Integrated Batten T-5 Tube Light Fitting 1x20 Watt with LED 20 Watt and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description (06 No.), complete all as specified and as directed. MAKE : HAVELLS E-LITE PRIDE PLUS 20W or equivalent Model in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

Supply & Hanging Ceiling Fan 1200mm Sweep, BEE 5 Star rated, 75 Watt, 50 Hz, 220/230 Volt AC, connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of Fan, complete all as specified and as directed.

S&F Exhaust Fan 230mm Sweep, Steel body with Louver Shutter, 230 Volt AC Supply with Fixing Arrangement using Fastener and providing Electrical Connections from Ceiling Rose to Exhaust Fan with and including PVC Flexible Cable of size 23/0.0076, 3 Core, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB (06 No.), complete all as specified and as directed.

S&F MCB Single Pole & Neutral 10 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB (01 No.), complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB (02 No.), complete all as specified and as directed.

S&F MCB Triple Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up, complete all as specified and as directed.

S&F MCB Distribution Board Sheet Metal Enclosure SPN, 4-way, 240 Volt AC, Single Door with Steel Phosphotised Powder painted, having 200 Amp rated Neutral Bars & Earth Bar and connecting up including Taking down/ out unserviceable MCB DB (03 No.), complete all as specified and as directed. MAKE : HAVELLS, Cat No. DHDPSHOSRW04 or equivalent Model in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

S&F MCB Distribution Board Sheet Metal Enclosure SPN, 4-way, 240 Volt AC, Double Doors with Steel Phosphotised Powder painted, having 200 Amp rated Neutral Bars & Earth Bar and connecting up, complete all as specified and as directed. MAKE : HAVELLS, Cat No. DHDPSHOSRW04 or equivalent Model in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

S&F MCB Distribution Board Sheet Metal Enclosure SPN, 8-way, 240 Volt AC, Double Doors with Steel Phosphotised Powder painted, having 200 Amp rated Neutral Bars & Earth Bar and connecting up, complete all as specified and as directed. MAKE : HAVELLS, Cat No. DHDPSHOSRW08 or equivalent Model in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

Supply & Laying or Passing through Pipe 1100 Volt grade heavy duty, Cross-sectional area 10 Sqmm, 2 Core, Flat or Circular Cable with PVC insulated Aluminium Stranded Conductor served with an Inner Sheathing of PVC Tape Armoured with Galvanised Steel Wire or Tape and Overall PVC Sheathed in Service Connection suspended by Insulating Hangers not more than 1.0 Metre apart with 4.0mm Dia Suspension Wire including Taking down/ out Unservice-able Service Connection (80.00 RM), complete all as specified and as directed.

M&L House Service Bracket (Hook type) complete with GI Pipe 32mm bore (dia), Medium grade, 3.0 Metre Long with 2 No. GI 40mm bore (dia) Bend 90° and reducing in Length if required by cutting, Mild Steel Hook and Stay or Guy, fixing with and including 2 No. Mild Steel Flat Iron 40x5mm Clamps of suitable Length, cut to Length, bent to Shape, drilling Holes, and Mild Steel Bolts, Nuts and Washers including applying Two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing of any description (03 Set), complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and Depth not exc. 1.50 Metre for Taking out/up and/or Laying of Water Pipe Line, Cable, etc., Forming Surfaces to required Foundation, etc. and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps along the Route of the Water Pipe Line, Cable, etc. with Surplus Soil in Soft/Loose Soil, complete all as specified and as directed.

Supplying & Laying LT Under Ground Cable 1100 Volt grade, XLPE insulated, PVC sheathed heavy duty, armoured with multi-stranded Aluminium Conductor all as per IS:7098 (Part-I)-1998 having Cross-sectional Area 35 Sqmm, 3½ Core, laid in Trenches, Ducts, Pipes or on Poles, etc. and Testing, complete all as specified and as directed. NOTE : Earth Works, Pipes, Concrete Cable Cover, etc. will be Measured and Paid separately under relevent Items.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only will be Measured.

Supply & Laying Sub-class ‘B’ Bricks, Kiln burnt as Mechnical Protection to Cable with Width Equal to Length of Brick, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, laid in Trenches, complete all as specified and as directed.

S&F Galvanised Steel Tubing 80mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, laid in Trenches, complete all as specified and as directed.

S&F Stop Valve 20mm bore (dia), Cast Copper alloy, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

AFTAB ENTERPRISES