Repair to Roof sheets, Sunken treatments and other Misc B/R work for OTM and Md Accn at Mil Stn Beas and Jandiala Guru under GE Kapurthala.

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for rendering 15mm thick cement plaster in cement mortar (1:4) on brick work or concrete surfaces of walls finished even and fair complete all as specified and as directed.

M&L for rough cast finish plaster with a mixture consisting of crushed stone or fine gravel aggregate mixed with coarse sand and cement in the ratio of 1:1:1 over & including 12mm thick rendering in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls complete all as specified and as directed.

M&L for rendering 15mm thick cement plaster in cement mortar (1:6) on brick work or concrete surfaces of walls finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 5mm thick rendering in cement mortar (1:3) on brick work or concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls and applying two coats of Oil Bound Distemper over a coat of appropriate primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over and including a coat of primer complete all as specified and directed

M&L for preparation of newly plastered surface of ceiling and applying two coats of white wash complete all as specified and directed.

Demolition of PCC in Ground floors/PCC Path/Plinth Protection and paving not exceeding 15cm thickness (below or above ground level) etc complete all as specified and as directed.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in plinth protection finished even and fair complete all as specified and directed.

Demolition cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Material & Labour for PCC type B-0 (1:2:4) (using 12.5mm graded crushed stone aggregate) as in parapets walls, benching, coping and filling at junction of brickwork and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete including use of forwork (straight or curved) complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep, including for inserting TMT bar as required length and shaping horizonatal/vertical face of groove making good where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good complete all as specified and directed.

M&L for RCC 1:1.5:3 , type A-0, using 12.5mm nominal size graded crushed stone aggregate as in chajjas, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L 5mm thick rendering in cement mortar (1:3) as in chajjas, roofs, landings, balconies, canopies, deck slabs and in shelves and the like finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending hooking etc & binding with and including mild steel binding wire (annealed) not less than 0.9mm dia complete all as specified and directed

M&L for form work to sides and soffits of beams chajjas and the like for rough finished surfaces of concrete complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal/sloping), rough finished surfaces concrete flat, complete all as specified and as directed.

Dismentling of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed.

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and as directed.

- ditto - all as per above item No. 22 but except bricks complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks using old size bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for joint free non-skid ceramic coloured tiles of approved pattern 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for joint free non skid ceramic coloured tiles of approved pattern 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors over and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and as directed.

M&L for coloured glazed ceramic tiles in vertical surface 450x300x7mm (of approved pattern) thick laid over 10mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile complete all as specified and as directed.

Dismantling asbestos cement (corrugated, semi-corrugated, etc) sheets as in roof coverings including ridges complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thicknness, including cover fillets complete all as specified and as directed.

M&L for ceiling using 9mm thick gypsum based ceiling tiles with weather resistance face on back side and vinyl finish including framework on the front fixed in 24mm GI Armstrong frame work of grid 600x600 mm size, the members of snap grid frame work of GI/Steel section of 24mm wide with T-flanges, channels etc of white colour having rotary stiching on all members, i.e main runner, 1200x600mm cross tee galvanised with minimum thickness of 120 gms per/sqm passed through 500 hrs test and hanging the same with existing roof members such as rafters, purlins or other wooden members particularly provided for hanging purpose using 8mm dia mild steel bar of required length fixed with nut bolt of 50mm long and 10mm dia of neck with washer flat iron 50x6mm thick clamps etc to steel members complete all as specified and as directed.

S&F 6mm thick PVC hollow wall panelling plain/coloured/printed fixed with screws to wall and corner, edges of panels be sealed with appropriate arrangement of approved colour and pattern complete all as specified and as directed.

Taking down chowkats or frames with shutters not exceeding 1.5 sqm each (without taking off shutters from the frames) complete all as specified and as directed.

Taking down chowkats or frames with shutters exceeding 1.5 sqm but not exceeding 4 sqm each (without taking off shutters from the frames) complete all as specified and as directed.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 Four Nos for each window including following fitting welded to frame shutter : (a) Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Fabrication & fixing arrangement as per drg No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note : Glass and painting shall be measured and paid separately under appropriate item.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, single rebated comprises gauzed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:3:6) type C-1 Four Nos for each window including following fitting welded to frame shutter : (a) Mild Steel Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 20mm x 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawing No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note : Wire mesh and painting shall be measured and paid separately under appropriate item.

M&L for steel ventilator fixed type with glazing bar without wire mesh and glass, complete all as specified and directed .

S&F solid PVC frame factory made as in door and cupboards of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specifications all as per SSR Part-I as specified and directed.

S&F factory made solid panel PVC moulded door shutter, 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing including fittings all as specified and directed.

M&L for framed work as in post, doors or gates and chowkhats of angle or other section with gusset plates, rails, braces, purline, truss etc, complete, drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening conforming to Gde Fe 290 (Gde E-165) complete all as specified and as directed.

Hacking out old broken glass (anythickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed.

S&F in repairs 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

S&F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples, wodden beads to steel windows/wodden doors complete all as specified and as directed.

S&F 100mm long stainless steel butt hinges medium weight complete all as specified and as directed.

S&F 125mm Aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 125mm Aluminium handles, cast type anodised complete all as specified and as directed.

Cutting chases, pinning in brick walls making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting exceeding 10 cm but not exceeding 20 cm girth complete all as specified and as directed.

M&L for cleaning the surface and made free of vegetation, dirt, foreign particles, liatance complete all as specified and directed.

M&L for rendering 10mm thick on brick or concrete surface in cement mortar 1:3 with water proofing compound finished even and smooth without using extra cement complete all as specified and as directed. Note :- Cost of water proofing compound shall be included in quoted rate for this item.

Supply and apply high build elastomeric waterproofing coat based on pure hydrophobic polyurethane cold applied or spray, brush applied, membrane with an elongation of 280 % and tensile strength of 2.7N/mm2 as per ASTMD 2370, crack bridging ability of 3mm, no leakage upto 5 bars of water pressure, minimum 88% solid content. The system shall include final base preparation, epoxy primer application with 100% water dilution and pure polyurethane application in two coats with minimum consumption of 1.2 kg/sqm, complete all as specified and directed. Note:- Application shall be done with company authorised applicator as approved by GE.

Uprooting of tree roots from walls/roof of any grirth at any height/location of any depth by dismantling brickwork/PCC and making good the damaged portion as existing by PCC 1:2:4 type B-0 and finished with 15mm thick plaster in 1:4 complete all as specified and as directed.

Taking down rain water pipes (any size and pattern), including all fittings, heads, shoes, bends, swan necks, etc. removal from site (measured overall as fixed along the centre line or fittings and accessories) complete all as specified and as directed.

S&F PVC rain water pipes (SWR) 110mm dia(Single socketed, in any length with rubber joints, fixed to walls with flat iron clamps complete all as specified and directed..

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 duly cuting, welding bending & fixing complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, complete all as specified and as directed.

M&L for PCC 100mm thick type D2, (1:3:6) using 40mm stone aggregate as in sub base of floors, for laying floor finishes complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15 mm thick cement mortar (1:6) for laying floor finished complete all as specified and as directed.

M&L for chequered cement concrete tiles 30cmx30cmx 25mm thick, set jointed and pointed in neat cement slurry in floors with pigment complete all as specified and directed.

M&L for sand filling under interlocking tiles including consolidation for laying floor finished complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block of approved pattern with grey cement and no pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade complete all as specified and as directed.

M&L for filling of sunken floor with PCC 1:5:10 using 40mm graded crushed stone aggregate including breaking and removal of existing filling of lime concrete/PCC/brick bats and rubbish out off the premises, etc complete all as specified and as directed.

M&L for two coats of hot bitumen on newly plastered surface of sunken portion not less than 1.2 Kg/Sqm complete all as specified and as directed.

M&L for plasteing in cement mortar (1:3) 15mm thick with WPC (200ml per bag of cement) on walls/ floor as on sunken floor finished even and smooth using extra cement,complete all as specified and directed. Note : After plaster, testing be carried out in the sunken portion by ponding for 72 hrs before further treatment to check any leakage/seepage. If observed shall be rectified without any extra cost by the tenderer.

Taking down GI tubing & connection 15mm dia laid in floor / trenches or fixed to walls complete all as directed.

S&F 15mm bore galvanized steel water tubing, medium grade with all fittings fixed to wall, ceiling or laid in floors complete all as specified and as directed.

Taking down GI tubing & connection 20mm dia laid in floor / trenches or fixed to walls complete all as directed.

S&F of 20mm bore galvanized steel water tubing, medium grade with all fittings fixed to wall, ceiling or laid in floors complete all as specified and as directed.

S&F in repair 15mm bore pillar taps, cast copper alloy with capstan heads chromium plated, fancy type, screwed down high pressure with or without lettered Hot or Cold with long screwed shank and fly nuts, complete all as specified and as directed.

S&F in repair 15mm bore long body bib tap with wall flange, cast copper alloy, chromium plated and screwed to iron pipes or union fittings complete all as specified and as directed.

S&F in repair for 15mm bore fancy type chromium plated stop valves, cast (angle cock) copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs 15mm bore PVC connection of 45cm long with two Nos of brass check nuts and washers complete all as specified and as directed.

S&F in repair 15mm bore chromium plated two way stop valves cast copper alloy screwed down high pressure with with crutch or butterfly handle, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs shower rose 15mm dia of chromium plated with shower arm 195mm long with bend of 45 degree complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) and cleaning and removing all scales and dust from PVC water tank manually and cleaning, scraping inner surfaces of tank by means of brush and then washing with clear water and cleaning of mouths of circulating pipes of capacity of tank exceeding 250 litre but not exceeding 500 litre including writing date of cleaned outer body of the tank with 100mm high by synthetic enamel paint (white/black colour) and reconnecting and refixing in position complete all as specified and as directed.

S&F in repairs 20mm dia aluminium chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified and as directed.

S&F in repair Vitreous China Wash Basin with full pedestal, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or eracting stand & waste pipe, coupling etc complete all as specified and directed including 15 mm dia Pillar taps, cast copper alloy with capstan heads Chromium Plated, screwed down high pressure, with or without lettered with long screwed shanks and fly-nuts, screwed for iron pipe but fancy type and fixed etc complete all as specified and directed.

S&F in repair vitreous china wash down water closet, "Orissa pattern" of size 580x440mm white, with integral foot rest (excluding flushing cistern and flush pipe) but including provision of cement concrete bedding complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devices with recessed bottom, jet spray, etc complete all as specified and directed.

S&F in repair low level flushing system PVC valveless syphonic action type, 10 ltrs capacity including supply pipe & fixing brackets of M.S. angle of size (25mmx25mmx3mm), 30cm long in PCC (1:2:4) type B-1, block of size (10cmx10cmx10cm) on walls etc complete all as specified and directed.

S&F in repairs vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed.

S&F urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight 60gms) complete all as specified and directed.

S&F of waste coupling suitable for urinals, bore dia of discharge pipe 32mm of PTMT (half or full threaded), (Minimum weight 45gms), complete all as specified and directed.

S&F in repair, 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair 32mm waste coupling of PTMT (half or full threaded) (minimum weight 40mm-60 gms) with PVC waste pipe for wash hand basin fixed complete all as specified and directed.

S&F in repair 40mm waste coupling of PTMT (half or full threaded) (minimum weight 40mm-60 gms) for sink fixed complete all as specified and directed.

S&F of 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210gms) complete all as specified and as directed.

S&F in repair 1000Ltrs capacity rotational moulded polythelene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position as per SSR Part-1 including fittings & 20mm dia brass ball valve complete all as specified and directed.

S&F in repair 500 Ltrs capacity rotational moulded polythelene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position as per SSR Part-1 including fittings & 20mm dia brass ball valve complete all as specified and directed.

JOGRAJ CONSTRUCTION COMPANY (BID ID -3323337)