PROVN OF CERTAIN SPECIAL REPAIR, REVENUE AND MINOR WORKS AT MIL STN KAPURTHALA UNDER GE KAPURTHALA

Amount

Dismantling of floor hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete in ground floors and paving n'exc 15cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-charge.

Demolition of reinforced cement concrete in slab/shelves, chajjas and similar suspended works including cutting reinforcement as required facilitating demolition complete all as specified and as directed by Engineer-in-Charge.

M/L for glazed ceramic coloured tiles in vertical surface 300 x200 x 6-7mm thick set and jointed in neat cement slurry pointed in white or colour cement to match the colour,with and including 10 mm thick cement screed bed (1:4) complete all as specified and directed by Engineer-in-charge.

M & L for non skid ceramic coloured tiles with matt finish, 6 to 8 mm thicksquare or rectangular area of each tile exceeding .11 sqm but not exceeding .18 sqm and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shade with and including 15 mm thick screed bed in CM 1:6 as in floors complete all as specified and directed by Engineer-in-Charge.

M&L for coloured glazed ceramic tiles (designer Pattern, HL) in vertical surface 350 x 250 x 7 mm / 450 x 350 x 7 mm /450 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed .(Make - Kajaria Crema Glossy or equivalent) as directed by the Eng- in charge

M/L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06sqm but n.exc 0.11 Sqm in floor set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles, with and including 15 mm thick cement screed bed in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M&L Non skid Ceramics tiles coloured of size 400x400x7mm thick in floor set & jointed in neat cement slurry and pointed in white/coloured cement to match with and including 15mm thick screed bed/bedding layers in CM 1:4, complete all as spd & directed. KAJARIA, Johnson.

M&L for machine cut kota stone slab flooring 16-18 mm in riser of step, skirting, dado and pillars thick over screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbishing and polishing complete including 20mm thick screed bed in CM 1:6 all as specified.

M&L for machine cut kota stone slab flooring 18-20 mm thick over screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbishing and polishing complete including 20mm thick screed bed in CM 1:6 all as specified.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including wind tie complete all as specified and directed by Engineer-in-charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-charge.

Supply and fixing Pre painted galvolume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

Supply and fixing Pre painted galvolume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

M&L for 12 mm thick perforated particle board 600x600x12mm for ceiling including aluminium snap grid frame work of 605x605mm and hangers 6 mm dia GI upto (1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x 3mm size & 60mm long and expansion hold fastner 12.5 mm dia 40mm long including two coat of OBD complete all as specified and directed by Engineer-in-charge.

Dismantling structural steel work as in purlins, rafters etc. as specified and directed.

S & F steel work in tubular/square/rectangular trusses ,rafters,purlin and posts etc including special shaped washer etc.complete using ERW or induction butt welded tubes conforming to IS-1161-1979(grade-st-240) all as specified and directed by Engineer-in-charge.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250) quality B complete all as specififed

M&L for rolled sections as in main and cross beams ,hip,jack raffters ,purlins where connected to common rafters Fe 410(grade E-250 quality-A)including a shop coat of red oxide complete all as specified and directed by Engineer-in-charge.

S&F rolled section as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates conforming to Fe 410-W(Gde-E-250) quality A complete all as specified and directed by Eng-in-charge.

Demolition of brick / block masonry built in CM including all quoins, arches, pillars etc and clearing off the premises complete all as specified and directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster on brick work or concrete surfaces including racking out joints complete all as specified and directed by Engineer-in-charge.

M & L for rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for 15 mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 finished the surfaces even and smooth with liquid water proofing compound without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for rendering 5mm thick cement plaster 1:3 on fair faces of concrete surfaces in ceiling

M&L for rendering 10mm thick cement plaster in cement mortar (1:3) on brick or concrete surfaces of soffits of chajjas, roof projections or ceiling and finished even and smooth without using extra cement complete all as specified and directed .

M&L for prepration of newly plastered surface and applying two coats of acrylic weather proof paint over a coat of primer complete all as specified and as directed.

M&L for Three coat of white wash on plastered/unplasterd surface on ceiling including preparation of new plastered surface complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of whitewash complete all as specified and directed by Engr-in-Charge

M&L for preparation of new plastered surfaces of walls and applying one coat of Birla white putty to obtain the true line to achieve smooth surface and applying two coats of oil bound distermper complete all as specified and directed by Engr-in-Charge

M & L for applying two coats of cement base paint on newly plastered or unplastered wall surface over a coat of cement primer including preparation of surfaces, complete all as specified and directed by Engineer-in-charge.

M & L applying two coats of cement base paint on old plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new wooden surface exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new steel surfaces of any description over 10cm girth or width not otherwise described and applying one coat of synthetic enamel paint over red oxide primer all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick cement plaster in CM 1:3 on bricks or concrete surfaces finishing the surfaces even and smooth without using extra cement all as specified.

Preparation of concrete surface and apply water proofing treatment to roof with APP (Atactic poly propylene) modified prefabricated five layer 3mm thick water proofing membrance super therolay of STP limited wth non-woven polyster male reinforcement of 160gm, weight of membrane @3.6kg/sqm over a solvent based bitumen primer, shalitex primer @ 0.3 lt/sqm by the same manufacturer conforming to IS-3384-1986.Apply two coat of alumnium paint on top of membrane surface after laying the membrane incl all cleaning Note : The membrane shall be laid using butane torch. The end lap should be 100 mm and the side lap must be minimum 75 mm. The membrane shall be first laid upto the parapet wall junction and then shall be overlapped with naother membrane (flashing) with and overlap covering upto a distance of 300mm. In case of parapet height is less than/ upto 500 mm membrane shall be terminated at the top of parapet.

Taking down chowkats or framed with shutter (with out taking off shutters from the frame) area not exc 1.50 sqm each complete all as specified and directed by Engineer-in-charge.

Taking down chowkats or framed with shutter (with out taking off shutters from the frame) area exc 1.50 sqm but n. exc. 4sqm each complete all as specified and directed by Engineer-in-charge.

S/F solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening complete all as specified and directed by Engineer-in-charge.

S &F factory made solid Panel PVC moulded door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing including fittings complete all as specified and directed by Engineer-in-charge.

S & F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge .

Supply and fix steel ventilators fixed partially glazed and partially gauzed type with glazing bars etc complete all as specified and directed by EIC.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 105 x 60mm complete all as specified and directed by Engineer-in-charge.

M&L for PCC 1:3:6 type C2 as in filling of chowkhats complete all as specified and directed by Engineer-in-charge.

S&F factory made 2nd class, hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to received glass, gauge, etc ( without sash bars) edges of framing plain, chambered or rounded, fitted with cut and mitred beads for securing glass , etc but difided into squares with plain chamfered or rounded mirted and rebated sash bars any numbers sizes of members of shutters as specified and directed by Engineer-in-Charge

S&F PVC cupboard frame of size 75mm x 40mm with wall thickness of 5mm made out of extruded 5mm thick Plain/Printed/Prelam PVC sheet reinforced with 15mm x 15mm M.S. square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners and jointed with 2 nos. of 150mm long brackets of 10mm x 10mm M S square tubes. The door frame shall be fixed to the wall using 65/100mm long MS screws through the frame by using PVC fasteners complete all as specified and directed by Engineer-in-charge.

S&F factory made PVC cupboard shutter flush type of 25mm thickness consisting of panel of hollow PVC profile of 12mm x12mm inserted all around the hollow profile section and insert one 10mm x 10mm MS tube in the centre of this section and lipped with 10mm thick(5mm x 2) and 12mm wide on stiles and rails using solvent cement the inner panel shall be laminated with 5 mm thick termite proof waterprrof and fire retardent printed PVC sheet using solvent cement on both sides of panel complete all as specified and directed by Engineer-in-charge.

S &F factory made 2nd class hard wood Plain, framed, panelled shutters 35 mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed by Engineer-in-charge.

S&F alumunium hinges for PVC door shutter, size of hinges 100mm complete all as specified and directed by Engineer-in-charge.

S&F 300mm long aluminium anodized sliding door bolt aluminium anodised not less than 12mm dia including a minimum of 6 nos of nuts and bolts all as specified.

S&F 200 mm aluminium anodized barrel tower bolt and fixed complete all as specified and as directed by Engineer-in-charge.

S&F 150 mm size, aluminium anodized handles, cast type and fixed complete all as specified and as directed by Engineer-in-charge

S&F 100mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

S & F steel window 1.25mm thick Box type ( primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises glazed Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Handles of Z Sec 20mm x 100mm long (b) stopper – 01 No per leaf (c) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (d) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf (e) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note: Glass and painting shall be measured and paid separately under appropriate item (ii) Irrespective of whatever shown on drgs, MS gills shall be of 12mm dia MS square bar and paid separately.

S&F steel window 1.25mm thick Box type ( primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises gauged Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Mild Steel Hold Fast,150mm long of 12mm Square bar made to shape – 04 Nos per window (b) Handles of Z Sec 20mm x 100mm long (c) stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (e) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note: Wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed.

S&F 4.00mm thick plain glass in squares n exc 0.5 sqm each pane and glazing with oil putty complete all as specified and directed by Engineer-in-charge.

S&F 4.00mm thick figured glass, pinhead type in squares n exc 0.5 sqm each pane and glazing with oil putty complete all as specified and directed by Engineer-in-charge.

S/F stainless steel wire cloth 0.56mm nominal dia of wire and avarage width of aperture 1.00mm and fixed with tinned tacks/screws with bolts incl leaping wooden complete all as specified and directed by Engineer-in-charge.

M/L for framed work such as grills gratings etc with ends of bars shouldered and or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framed work of water tanks and similar work complete all as specified and directed by Engineer-in-charge.

S/F in repairs of size 300mm MS ordinary rat tail rod pattern helical springs including roller and roller plate complete all as speicified

Taking down GI tubing & connection of 15mm dia of bore laid in floor / trenches or fixed to walls complete all as directed by Engineer-in-Charge.

S&F GI tubing 15mm dia bore medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.

Taking down GI tubing & connection 20mm dia laid in floor / trenches or fixed to walls complete all as directed by Engineer-in-Charge.

S&F GI tubing 20mm dia of bore medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.

S&F in repairs 15 mm bore CP bib taps fancy type cast copper alloy with crutch or butter fly handle screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repairs Chromium Plated long body Bib taps, cast copper alloy with crutch or butterfly handle with wall flange with aerator, screwed down, screwed for iron pipe or for brass ferrule and fixed of 15mm bore (Cat Pt No MQT-512, Essco Marvel series or equivalent) complete all as specified and directed.

S&F 15mm dia stop valve/ angle valve, CP cast copper alloy with crutch or butterfly handle. Screwed down high pressure, screwed both ends for iron pipe and fixed complete all as directed by Engineer-in-charge.

S&F in repairs 15mm dia stop valve, CP cast copper alloy with crutch or butterfly handle. Screwed down high pressure, screwed both ends for iron pipe and fixed complete all as directed by Engineer-in-charge.

S & F in repair PVC connection 15mm size with PTMT nuts of length300mm all as specified and directed by Engineer-in-Charge.

S&F vitreous china European type wash down water closet pan (Pedestal pattern) of white colour including plastic water closet seat cover closed pattern with flat bottom (with MS or CP hinging device) and fixing bolts, P or S trap, necessary inlet and outlet connections including syphonic action type low level PVC flushing cistern of 10 lit capacity white in colour and PVC flush pipe 32mm dia complete.

S & F in repairs Vitreous China bowl urinal angle back of size 430 x 370 x 340mm with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and as directed by Engr-in-Charge etc complete all as specified.

S & F Vitreous china urinal partition white of size 310 x 700 mm complete all as specified & as directed by Engineer-in-charge.

Supply and fix in repairs vitreous china squatting pan Orissa pattern wash down water closet of size 580x440 mm, white, with integral foot rests complete fixed with P or S trap, PVC flushing cistern low level of Make 10 ltrs capacity including brackets for flush tank, PVC flush pipe and all necessary fittings etc complete all as specified and directed by Engineer-in-charge.

S&F 20mm dia aluminium chromium plated tubular towel rails,D type,60cm long between flanges, complete all as specified and directed by Engineer-in-charge.

M&L for PVC SWR floor trap 75mm dia with grating including jointing to waste pipe with solvent cement all as specified and directed by Enginee-in-Charge.

S&F in repairs fancy type chromium plated stop valves with long shank and cup (concealed type) cast copper alloy screweddown high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed for bore of size 15mm complete all as specified and directed by Engineer-in-charge.

Supply and fix in repair for vitreous china ware wash basin white, flat back size 550 X 400mm including 15mm dia pillar tap chromium plated, CP waste coupling, waste fittings, union and waste pipe 32mm dia of required length and all necessary inlet, out let connections complete all as specified and directed by Engineer-in-charge.

S&F in repairs shower rose of chromium plated any colour or fixing with 15mm bore pipe (minimum weight 40gm) complete all as specified and directed by Engineer-in-charge.

S&F in repair kitchen sink with drain board made of stainless steel 1mm thick sheet with plugs, washers and wastes including bedding in cement mortar including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-charge.

S&F soap dish, CP heavy duty complete all as specified and directed by Engineer-in-charge.

S&F shelf of glass fixed with and including chromium plated brass screws and wooden plastic cleats(min. weight 300gm) complete all as specified and directed by Engineer-in-charge.

S&F in repair 25mm MS curtain rail powder coated with fixing brackets, stops etc as specified and directed.

Applying evenly a tack coat of industrial bitumen 85.25 @ 1.20 Kg/sqm including cleaning surfaces complete all as speciified and as directed by Engineer-in-Charge.

M&L for PCC (1:5:10) type E2 using 40mm graded aggregate thick as in sub base complete all as specified and directed by Engineer-in-charge.

Cutting chases pinning in brick/stone/blocks masonary in making good to facings where required and pointing in CM (1:3) to ends or eges of steps, cills, sun shades, shelves, lintel etc and cutting chases for concealed water tubing or etc and making good, complete all as specified and directed by Engineer-in-charge.

Taking down eaves gutters and rainwater pipes including all fittings complete all as specified and directed by Engineer-in-charge.

S&F 110 mm PVC (SWR) pipes single socketed in any length laid in trenches,floor or fixed on wall complete all as directed by Engineer-in-Charge.

S&F 75 mm PVC (SWR) pipes single socketed in any length laid in trenches,floor or fixed on wall complete all as directed by Engineer-in-Charge.

S&F PVC SWR floor trap 100mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating all as specified.

S&F 110 mm PVC (SWR) pipes in repair single socketed in any length with rubber ring joints fixed to walls complete all as directed by Engineer-in-Charge.

S&F 75 mm PVC (SWR) bend complete all as directed by Engineer-in-Charge.

S&F 110 mm PVC (SWR) bend complete all as directed by Engineer-in-Charge.

S&F PVC (SWR) junction single 110mm,(single T) equal or unequal complete all as directed by Engineer-in-Charge.

S&F 110mm PVC(SWR) vent cowl complete

Add to Item no 96 75mm for access door complete as specified.

Add to Item no 97 and 98 110mm for access door as specified.

Dismantiling water tank PVC 500 Ltrs and removing from site complete all as specified and directed by Engineer-in-charge.

S&F rotational moulded polythelene water storage tanks cylindircal water tank for hoisted and fixed in postion of 500 ltrs capcity including fittings and as directed by Engr-in-Charge

S&F gunmetal globe and gate valve with iron welded hand secrewed both and for iron pipe 20mm fixed in repairs complete all as specified and directed by Engineer-in-charge.

S& F in repairs Ball valves 20mm high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210 gms./25mm-455gms/ 40mm - 690 gms) complete all as specified and directed by Engineer-in-charge.

M&L for Reinforcement cement concrete Type M-25 design mix (20mm graded crushed aggregate) as in slabs/shelves supported on walls complete all as spd and directed.

M&L for reinforced cement concrete M-25 Design mix as in lintel bend/roof beam/RCC coping complete all as specifed and directed.

M&L for Reinforcement cement concrete Type M-25 design mix (20mm graded crushed aggregate) as in slabs/shelves supported on walls complete all as spd and directed.

M&L for reinforced cement concrete M-25 Design mix as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Material and labour for reinforced cement concrete (Design Mix) M-25 (20mm graded crushed stone aggregate) as in chajjas complete all as specified and as directed by Engineer-in-Charge.

M&L for reinforced cement concrete M-25 Design mix as in lintel bend/roof beam/RCC coping complete all as specifed and directed.

M&L for reinforced cement concrete M-25 Design mix as in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam, RCC coping rough finished surface complete all as specified and directed.

M&L for flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified and directed.

M&L for Formwork to square/reactangular sides of pillars, posts, struts, piers, columns, and stanchions fair and finished surface complete all as specified and directed

M & L for formwork to soffits of suspended slabs such as roof slab n.exc 200mm thick complete all as spd and directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as spd and directed.

S&F Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns,hooking ends and binding with and including mild steel wire (annealaed) not less than 0.9mm dia or securing with clips quality conforming to Fe-310-0 or Fe-410-0 all as specified and directed incl drilling to cement conc surface for fixing of reinforcement in position all as specified.

S&F Mild steel TMT bars 6mm to 8 mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns,hooking ends and binding with and including mild steel wire (annealaed) not less than 0.9mm dia or securing with clips quality conforming to Fe-310-0 or Fe-410-0 all as specified and directed incl drilling to cement conc surface for fixing of reinforcement in position all as specified.

Ditto as above item no 119 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

Excavating over areas, not exceeding 1.5m in depth for foundations and getting out in soft / loose soil all as specified and directed by Engineer-in-Charge.

M&L for Hardcore of gauge n exc. 63 mm of broken stone, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed by Engineer-in-Charge.

M&L for Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, 20mm thick; joints grouted in cement mortar 1:2 with an admixture of metallic floor hardner, 5% by weight of cement and struck flush all as specified and directed by Engineer-in-Charge

S&F Edge stones to flooring with stone setts of size 250 to 300mm long x150 to 200mm wide, and 450mm deep and ditto as per Srl item No 123 above complete all as specified and directed by Engineer-in-Charge

Supply only Metallic floor hardener

S&F 35 mm thick Second class hard wood (Hollock) plain framed panelled, door shutter (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS: 1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

Supply only Liquid water proofing compound

Taking up or down, steel tubing 25mm bore and connections including removal complete all as specified and as directed by Engineer-in-Charge.

Supply and fixed in repair 25 mm bore Gun-metal, globe or gate valves , with iron wheel head, screwed both ends for iron pipe.

S&F 25 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors. (Make - Jindal / Prakash Surya)

Surface dressing not exceeding 15cm deep as in soft/loose soil complete all as specified and directed by Engineer - in - Charge.

M&L for PCC (1:5:10) type E2 using 40mm graded aggregate as in subbase complete all as specified and as directed by Engineer-in-Charge.

M & L for machine pressed precast cement concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and no pigment complete all as specified and directed by Engineer-in-Charge.

Supply and lay Sand under floors or in foundations including watering and consolidation complete.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth, for foundations etc or man holes, cesspits etc. not exc 10 Sqm on plan and getting out in soft / loose soil all as specified and directed by Engineer-in-Charge.

Removing excavated material not exc. 50mtrs and depositing where directed at a level not exc. 1.50mtrs above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick all as specified and directed by Engineer-in-Charge

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth, in layers not exceeding 25cm, watering, and removing surplus spoil to a distance not exceeding 50m and making good surface all as specified and directed by Engineer-in- Charge.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed by Engineer-in-Charge

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate for foundations, fillings and mass concrete all as specified and directed by Engineer-in-Charge.

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in bed to drain pipe including packing under and haunching against the sides of pipes 150mm dia (internal) after these are laid in trenches all as specified and directed by Engineer-in-Charge.

M&L for providing precast cement concrete type C1 1:2:4 (20mm graded aggregate) as in kerbs , edging set in CM (1:4) exposed surface even and smooth complete all as specified

M&L for 75mm thick PCC 1:3:6 type C2 as in plinth protection finishing the surface even and smooth with out using extra cement complete all as specified and directed by Engineer-in-charge.

M & L for pre-cast RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in man hole cover slabs, of any thickness, size or shape including necessary from work, finished concrete surfaces fair and even in cement mortar set in CM 1:4 all as specified and directed by Engineer-in- Charge.

M & L for cement concrete (1:2:4) B-1 using 20mm graded stone aggregate as in lintels up to 1.5 m clear span, benching, coping, bed blocks and roof kerbs etc including use of necessary form work all as specified and directed by Engineer-in-Charge .

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in benching, coping etc. including necessary form work complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete (1:2:4) type B-1 using 20mm graded stone aggregated as in roof padding kerbs, mud stops, coping, etc edges of concrete rounded or chamfered complete all as specified and as directed by Engineer-in-Charge.

M&L for 25mm thick cement concrete type B0, 1:2:4(12.5mm graded crushed aggregate) as in floor including fair finished even and smooth without using extra cement complete all as spd and directed.

M&L PCC type B-0 (1:2:4) (12.5mm stone graded aggregate), 40mm thick as for receiving top finishing layer of ceramic tiles for sunken portion finished even and smooth etc complete all as specified and directed.

M & L for 100 mm thick cement concrete 1:2:4 type B–2 using 20mm graded stone aggregates as in flooring finished even and smooth without using extra cement all as specified and directed by Engineer-in-Charge .

M/L for RCC 1:2:4 type B-1 (20mm graded) as in Roof slab supported on walls etc

M & L for RCC 1 : 2 : 4, Type B-1 using 20 mm graded stone aggregate as in beams, lintels complete all as specified and directed by Engineer - in - Charge.

M & L for RCC 1 : 2 : 4, Type B-1 using 20 mm graded stone aggregate as in foundation, filling complete all as specified and directed by Engineer - in - Charge.

M&L for 40mm damp proof course in cement concrete 1:2:4 type B-0 to horizontal surfaces including necessary formwork complete.

M & L for 150mm dia (internal) SGSW pipes grade ‘A’ laid in trenches and jointed all as specified and directed by Engineer-in-Charge.

M & L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benches for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150mm internal dia for pipe is 150 mm all as specified and directed by Engineer-in-Charge.

Taking down aluminium point wiring for light, fan, bell socket, power socket etc complete including fittings and fixtures removing from site and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge

Material and labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC (FRLS) insulated cable in PVC concealed conduit of size 20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 1.5 Sqmm insulated un-sheathed PVC insulated copper conductor common earth and connecting to earth dolly for :-

(a) One light point controlled by one, one way switch

(b) One fan point controlled by one, one way switch

(c) One socket outlet 3 Pin, 5 Amp on independent board

(d) One socket outlet 3 Pin, 5 Amp on same board.

(e) One bell point controlled by one bell push

M&L for point wiring with 4.0 Sq mm single core multi-stranded copper conductor PVC (FRLS) insulated, unsheathed cable 1100 volt grade in PVC concealed conduit of size 20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 4.0 Sq mm single core, multi-stranded copper conductor, PVC insulated, unsheathed cable for common earth and connecting for earth dolly for 5 pin, 15 Amp socket outlet on Independent board.

S&F switch piano flush type single pole one way 5 Amp (ISI Marked) Make - SSK/Anchor/Cona

S&F switch piano flush type single pole one way 15 Amp (ISI Marked) Make - SSK/Anchor/Cona

S&F Bell push flush type single pole one way 5 Amp (ISI Marked) Make - SSK/Anchor/Cona

S&F socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked) Make - SSK/Anchor/Cona

S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked ) Make - SSK/Anchor/Cona

M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked) Make - SSK/Anchor/Cona

M&L for bell multi music type, AC 230 Volts, single pole (ISI Marked)

Taking down old unserviceable flourescent tube light fitting 36/40 watt fluorescent tube light fittings direct to walls or roof as ordered and disconnecting electrically with the electrical system and all materials required for the same. The rates also include making good the same to match with the existing surface.

Supply, installation, testing and commissioning of 20 watt 4 ft long LED Batten housing made of extruded alluminium with milky white diffuser and inbuilt electronic driver system lumen output should be at least 1800 lumen with a CCT of 6000 K, power factor should be greater than 0.9 with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed Make Polycab or equivalent in Philips/Bajaj/C&S electric/Surya

Taking down unserviceable MCB’s and supply & fix following type/rating MCB’s including necessary connection as under:-

(a) S & F of MCB, 10 to 32 Amp, SP, 240 Volt Make - Legrand/Schneider-Acti 9/Siemens-Betagard

(b) S&F of MCB, 40 to 63 to Amp, SPN, 240 Volt Make - Legrand/Schneider-Acti 9/Siemens-Betagard

Taking down old unserviceable sub main wiring 6.00 Sqmm 1100 volts grade two runs of single core PVC insulated, unsheathed copper condutor, including taking down casing capping/PVC conduit.

M&L for sub main wiring with two runs of single core PVC insulated, unsheathed copper condutor (FRLS), multi stranded cable of size 6.00 Sqmm 1100 volts grade drawn PVC concealed conduit of size 20 mm (ISI marked) including PVC accessories complete incl cutting and chasing and making good etc including one run of 6.00 Sqmm single core copper conductor multi-stranded PVC insulated, unsheathed cable as earth wire continuity conductor complete all as specified and directed by Engineer-in-Charge. Note : Two run of 6.00 Sqmm cable one run of 6.00 Sqmm cable as earth continuity conductor and one run of PVC Conduit shall be measured & paid as one unit.)

Taking down old unserviceable wall mounting fitting/Holder & supply & fix decorative wall mounting type made up of polycarbonate rings, and glass shade with lamp holders, connectors block, 1 x 09 watt LED Blub,glass fitted engineering plastic B22 d lamp holder with electrical copper contactcs, self screwed polycarbonate diffuser in opal finish for soothing light effect, LED 09 watt etc complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable complete Make ; Havells or equivalent in bajaj & philips

Taking down oold unserviceable lamp holder and S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including LED lamp 12W.

Taking down old unserviceable bulkhead fitting & supply & fix bulkhead fitting decorative ceiling/wall mounted BULK HEAD with engineering plastic housing and top frame with opal PMMA diffuser suitable for 1 X 06 watt LED Blub including 1 No of 06 watt LED of C&S electric or equivalent in model of Philips or Bajaj complete all as specified and directed by Engineer-in-Charge,

Taking down old unsv DB and supply and fixing factory made sheet metal enclosure double door distribution board class IP-43 with 200 Amp rated copper bus bar 240 volts 8 way single pole and neutral link complete all as directed by Engineer-in-Charge.

Taking down old unserviceable regulator & supply & fix electronic type fan regulator stepped type on existing phenolic laminated sheet etc. suitable for ceiling fan.

Taking down old unserviceable GI pipe & Supply and fixing 40 mm dia GI tubing medium grade complete with all fittings (ISI Marked) lain in trenches/fixed complete to wall and ceiling or laid in floors

Supply and lay cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric cable (heavy duty) 1100 volts grade with standard aaluminium conductor of size 16 Sqmm 4 core.

M&L river washed and screened dry fine sand filling in trenches below and above / around under ground cable for cable protection including punning around cable complete all as specified and directed. Note:- 18mm thickness after punning down shall be imeasured recorded & paid.

M&L for well brunt bricks sub class 'B' in old size as cable protection laid flat width wise complete all as specified and directed.

Supply, install, testing and commissioning of LT panel size 650 mm x 500 mm x 150 mm enclosures cubical weather and vermin proof totally enclosed made out of 1.6 mm thick CRCA sheet machine pressed of suitable size to operate on 3 phase 4 wire system 415 Volts, 50HZ double door with front openable and PVC acrulic glass cover suitable size for checking of meter reading without opening door with locking arrangement incl inner shutters for mounting switch gear etc, suitable arrangement for fixing of electrical meter and SPN 40 to 63 Amp including pre wiring from Bus bar to Meter and Meter to MCB SPN (for pre wiring use 6.00 Sqmm Single core copper cable and suitable size of lugs for connecting from Busbar to meter and meter to MCB SPN) including bottom gland plate with sufficient numbers of circular cable entry holes, including prewired complete as per drawing with masonary work for fixing in wall duly powder coated with comprising of the following :- INCOMING :- (i) Aluminium bus bar 200 Amps capacity with bus bar supports, DMC/SMC insulators of CPRI approved of suitable length insulated heavy heat shrinkable sleeves etc -04 Nos. OUT GOING (i) MCB 40 Amp, 230 Volt, 10 KA, Single pole and neutral -02 No Make : Legrand/Siemens/Schnedier (ii) S&F single phase electronic energy meter with LCD display of rating 10-40 Amp class 1.0, 240V 50 Hz counter type display with transparent hinge including connection from SPN to meter with 6 Sqmm copper stranded conductor including earth wire complete all as specified and directed by Engr-in-Charge.Make-HPL or equivalent in Neptune - 02 Nos

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed. (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Item includes the cost of 7.50m GI pipe for protection of earth wire/strip Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.50m earth lead wire/strip. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

COSMO BUILDERS