138WE/L-106/2025-26

Amount

Demolition of cement concrete in ground floor and pavings not exc 15cm thick below or above ground level complete all as specified and/or as directed by Engr-in-Charge

Demolition of precast concrete block walling built in cement mortar complete all as specified and/or as directed by Engr-in-Charge

Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and/or as directed by Engr-in-Charge

M&L for 15mm thick rendering on other than fair faces of brick work finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and/or as directed by Engr-in-Charge

M&L for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and/or as directed by Engr-in-Charge

M&L for 5mm thick rendering on ceiling finished even and smooth without using extra cement in cement mortar 1:3 complete all as specified and/or as directed by Engr-in-Charge

M&L for three coats of white wash on newly plastered surfaces of ceiling incl preparation complete all as specified and/or as directed by Engr-in-Charge

M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of chalk whiting complete all as specified and/or as directed by Engr-in-Charge.

M & L preparing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered surfaces with alkali resistant priming paint on surfaces of walls, complete all as specified and/or as directed by Engr-in-Charge.

Taking down chowkats/ frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each complete all as specified and/or as directed by Engr-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and/or as directed by Engr-in-Charge.

M&L for hard wood 2nd class factory made wooden boarded floors 10mm thick and skirtings planed one side & edges tonged and grooved or rebated, including backing with thermocol sheets or as specified by manufacturer including dismantling complete all as specified and/or as directed by Engr-in-Charge

M & L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:4 screed bed or bedding layer of mortar and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge

M & L glazed (coloured) ceramic tiles of size (350 x250mm) x 7 mm / 450mm x 350mm x 7mm thick, as on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement as in dado, skirting etc to match with the shade of tiles including rendering 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces as in vertical surfaces for receiving tiles all as specified and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc. laid bedded and pointed in any mortar, complete all as specified and/or as directed by Engr-in-Charge.

M&L for Machine cut Kota stone slab flooring 20-25 mm thick over cement screed bed 20mm thick in CM 1:6, set and jointed in neat cement slurry laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and/or as directed by Engr-in-Charge.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.

M&L for precast solid block masonry set in CM 1:6 & casted in cement concrete type C-1 (1:3:6) using 20mm graded crushed stone aggregate complete all as specified and/or as directed by Engr-in-Charge.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fix in the frame at site complete all as specified and/or as directed by Engr-in-Charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and/or as directed by Engr-in-Charge.

S&F for 30 mm thick 2nd class soft wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supply and fixed to chowkats, complete all as specified and/or as directed by Engr-in-Charge.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and/or as directed by Engr-in-Charge.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (3 Nos) suitable handle (1 No) etc. complete all as specified and/or as directed by Engr-in-Charge.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and/or as directed by Engr-in-Charge.

M&L sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and/or as directed by Engr-in-Charge.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and/or as directed by Engr-in-Charge.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and/or as directed by Engr-in-Charge.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and/or as directed by Engr-in-Charge.

S&F floor door stopper (length of cover plate ) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and/or as directed by Engr-in-Charge.

S&F 75mm long aluminium anodized, butt hinges of extruded section complete all as specified and/or as directed by Engr-in-Charge.

S&F 100mm long aluminium anodized, butt hinges of extruded section complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and/or as directed by Engr-in-Charge

Supply and fix rotational moulded polyethylene puff water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories, including dismantling of water tanks and remove to store, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in repairs 25mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in repairs 25mm ball brass valves, high pressure with polythene float and fly nut complete screwed for iron/ PPR pipe, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in repairs fancy type 15mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and/or as directed by Engr-in-Charge.

Taking up or down steel tubing 25mm to 32 mm bore including cleaning for refixing or removal to store, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix 25 mm bore 3 layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain and brass threaded polypropylene random fitting fixed complete to walls, ceiling or floors, complete all as specified and/or as directed by Engr-in-Charge.

All as per item No 38 above, but 32 mm bore pipe.

Supply and fix in repairs vitreous China squatting pan of Orissa pattern 580 x 440 mm white with integral foot rest (excluding cistern) with front or back inlet any pattern incl bedding with PCC 1:2:4, type B-I using 20 mm graded crushed stone aggregate, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in repairs 10 ltr capacity PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and/or as directed by Engr-in-Charge.

Supply only PVC (SWR) 'S’ trap of 110 mm bore, complete all as specified and/or as directed by Engr-in-Charge.

M&L for PVC (SWR) pipe single socketed, 110mm soil, waste and rain water drainage pipes fixed with wall including taking down, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix 110 mm dia (SWR) bend any radius, complete all as specified and/or as directed by Engr-in-Charge.

S&F PVC (SWR) vent cowl of 110mm bore, complete all as specified and/or as directed by Engr-in-Charge.

S & F in repairs, PVC (SWR) 75mm dia, floor trap, plain with grating including jointing to waste pipe with solvent cement, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix PVC connections 15mm size with PTMT nuts (length 600mm), complete all as specified and/or as directed by Engr-in-Charge.

S & F in repair Vitreous China wash basin, white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and/or as directed by Engr-in-Charge.

S & F in repairs 750 mm long, 32/ 40 mm dia., PVC flexible Waste pipe for sinks / wash hand basins, complete all as specified and/or as directed by Engr-in-Charge.

Supply only 32mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams)

M&L for preparation of old plastered ceiling surfaces of any description and applying two coats of white wash complete all as specified and/or as directed by Engr-in-Charge.

M & L for complete removal of existing treatment, preparing old plastered surfaces of wall and applying two coats of distemper oil emulsion, complete all as specified and/or as directed by Engr-in-Charge.

M & L for two coats of cement base paint on old plastered surfaces including preparation of surfaces, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs complete all as specified and/or as directed by Engr-in-Charge.

S&F in repairs Soap dish Chromium plated, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repairs Towel rail 600mm long Chromium plated (Minimum weight 190 gms), complete all as specified and/or as directed by Engr-in-Charge..

S & F in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and/or as directed by Engr-in-Charge. Make:- Cera/Jaquar/Hindware

M&L for preparation of new or previously untreated wooden surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and/or as directed by Engr-in-Charge.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and/or as directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface complete all as specified and/or as directed by Engr-in-Charge

Taking down carefully sub main wiring/service wire of any description complete all as specified and/or as directed by Engr-in-Charge

M & L for Point wiring complete with 1.5Sq.mm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC Casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5Sqmm copper conductor cable as continuous earth lead complete all as specified and/or as directed by Engr-in-Charge for the following :-

One light/exhaust fan point controlled by one way switch.

One switch socket outlet 6 Amps, 230 volts point on same board.

One switch socket outlet 6 Amps, 230 volts point on independent board.

All as item No 64 above, but using cables 4 Sqmm.

Supply and fix in replacement of lamp holder insulated body with back plate complete all as specified and/or as directed by Engr-in-Charge

Supply and fix of Switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix of switch Socket out let two in one 5 pin 6 Amps flush type.230 volts complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix of switch Socket combination out let multi purpose 5 pin 6 Amps and 16Amps 230 volts complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix of Ceiling rose, surface Bakelite three terminals complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement sheet metal enclosure Vertical Tripple Pole and Neutral DB 4 way 433 Volts complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement MCCB TPN 250 Amp, 36 KA, Adjustable type 433 Volts AC ISI marked complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 12 Ways complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 8 Ways complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix MCB SPN 63 Amp 240 Volts AC ISI marked complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix MCB SP 6-32 Amps. 240 Volts 50 HZ complete complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing Caping wire size 2x25.0 sq. mm + 1x16.0 sq. mm earth wire complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing Caping wire size 2x16.0 sq. mm + 1x16.0 sq. mm earth wire complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement LED light fitting 1x 20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement connecting and testing LED security light fitting 35 watt, 230 volt, AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp and bracket with impact and corrosion resistant incl thermal management in multiple optics complete with IP65/66 protection complete complete all as specified and/or as directed by Engr-in-Charge

M&L for Earthing complete with galvanized steel earth plate electrode 600mm x600mmx 6mm thick buried directly in ground. (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5m below normal ground level, connected to galvanized earth lead wire 4mm dia by GI watering pipe with funnel and wire mesh and 15mm dia protection pipe earth work etc complete all as shown in electrical plate No 3 of MES SSR Part-I, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix Air Circulator steel body AC single Phase 230V of size 300 mm with electronic driver blades, and frame and louvers complete all as specified and/or as directed by Engr-in-Charge.

Supply, laying and testing cable XLPE in replacement Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50.0 sq mm 3.5 core, complete all as specified and/or as directed by Engr-in-Charge.

Excavating in trenches not exceeding 1.5 m wide and not exc. 1.5 mtr in depth and getting out in hard/dense soil, complete all as specified and/or as directed by Engr-in-Charge.

M&L for Sand cushioning to under ground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of SSR Part-I, 2009. Note : Punned thickness will be measured and paid.

Supply and laying of factory made, machine pressed, unreinforced, pre-cast concrete cable cover class LV type-2 flat size 250 mm x 150 mm x 40mm, complete all as specified and directed

Returning, filling in, including spreading levelling watering and well ramming in layers not exceeding 25 cm, complete all as specified and/or as directed by Engr-in-Charge.

Removing excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and/or as directed by Engr-in-Charge

M/S RAVINDER SINGH (BID ID -3369385)

KAMLA CONSTRUCTION COMPANY (BID ID -3369900)