ADDN ALTN TO BLDG NO T-13, SPL REPAIR TO INTERNAL SUB MAIN WIRING AND LT CABLE FOR BLDG NO P-19/1 TO P-22/6 (24 X OR MD ACCN) AND SPL REPAIR TO CEILING FANS AND GEYSERS AGAINST BER AT MIL STATION BARABANKI UNDER GE (EAST) LUCKNOW

Amount

Dismantling of asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings/cladding complete all as specified and directed.

S&F prepainted GALVALUME aluminium zinc coating GI based corrugated sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading to wall fixed with self tapping screws complete all as specified and directed.

S&F prepainted GALVALUME Aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F mild steel rolled section as in main and cross beams, hip and jack rafters, purlins where connnected to common rafters and running rails and guides for sliding doors fixed with angles cleats or other connecting plates confirming to Fe 410- W (Gde-E-250) complete all as specified and directed.

All as item No. 5 above but fixing only ( Note: Old numbers shall be used obtained from dismantling)

Demolition of brickwork built in cement or cement lime mortar including all quoins, arches pillar etc complete all as specified and directed.

Dismantling wall & ceiling boards (fibre, insulation etc) or insulation boards, slabs, blankets any thick ness including cover fillets complete all as specified and directed.

M&L for aluminium anodised snap grid frame work of size 605X605mm for false ceiling with hanging arrangement of 6mm dia G.I (up to 1200mm length) adjusting level fixed to roof slab complete all as specified in clause No 10.38 of MES SSR 2009 (Part I- specification).

M&L for asbestos 12mm thick fibre cement builing boards fixed or laid/ inserted to aluminium frame work with screws as in false ceiling fixed in ceiling flat or sloping complete all as specifed and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area not exc 1.5 sqm each and removing from site complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area exc 1.5 sqm but not exc 4 sqm each and removing from site complete all as specified and directed.

Taking down cement plaster in any description on brick or stone wall etc. including racking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces, finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coat of oil bound distemper over a coat of wall care putty (3mm thick) on wall complete all as specified and directed.

M&L for preparation of new plastered surface of wall including cornices etc and applying two coat of cement bases paint over a coat of primer surface on wall complete all as specified and directed.

Excavation in trenches not exc 1.5 M wide and not exc 1.5 M in depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes etc not exceeding 10 Sqm on plan and not exceeding 1.5 M in depth and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:5:10 type E-2 using 40mm graded stone aggregate as in foundation, filling in mass concrete etc complete all as specified and directed.

M&L for brick work using old size fly ash brick, straight or curved on plan exc 6m mean radius, built in CM (1:6), complete all as specified and directed.

Removing of excavated materials to a distance not exc 50m and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed.

M&L for mild steel TMT bar 10 mm dia and over as in reinforcement cut to length, bent in shape required including cranking, bending, spirally hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc.complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over upto 8mm dia as in reinforcement cut to length, bent in shape required including cranking, bending, spirally hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc. as in sttirups complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded agg) in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns; etc; basement slabs; under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded agg) in columns, pillars piers post and struts complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded agg) in beams, cantilevers, bressummers; lintels over 1.5m span complete all as specified and directed.

M&L for formwork to sides of concrete foundation, footings, bases of columns, rafts & rafts beams, sides & soffits (if any) of foundation & plinth beams; & similar work; vertical or to batter complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for formwork to sides & soffits of floor or roof beams haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. complete all as specified and directed.

S&F aluminium body door closer hydraulically regulated, designation No.3, universal type,suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F glazed powder coated aluminium sliding windows with shutter , frame with aluminium grill, made with aluminum section of size as appended below:- (i) Frame: 61.85X31.75X1.3mm for top and side rails and 68.5X31.75X1.2mm for bottom rail.(ii) Shutters- 38X18X1.5mm suitable for shutter glass with runners.(iii) Glass: 4.80mm thick fixed with rubber gasket and aluminum clips. (iv) Grill: Aluminum grill 7.5mm dia make- Dean grill or Allumigrill fixed to alum section 50X20X1.5mm complete all as specified and directed.

S&F galzed powder coated aluminum doors complete with frame, shutter, Galzing shall be of 4.8mm thick sheet, fixed with rubber gasket and aluminum glazing clips, section fo aluminum doors of following sizes:- (a) Frame 100X40X2mm thick section No. 2420. (b) Shutter - (i) Styles 85X44.45X3mm thick section No. 4526. (ii) Top rail 95.25X44.45X1.7mm thick section No. 4553. (iii) Middle/lock rail 83.50X44.45X1.7mm thick section No. 4565, (iv) Bottom rail 114.3X44.45X2.82mm thick section No. 4529, (v) Galzing clip 0.70mm thick section No. 4407, (vi) Handle: round aluminum handle 100mm girth and as per sample, (vii) Tower Bolt: 9.90mm dia sheet and 200mm long, (viii) Mortic lock: 100 mm size, 4 lever of Godrej.

S&F ceiling fan of 1200 mm sweep,220-240 volt, AC, 50 Hz,350-370 RPM,with air delivery of 215 cmm or more BEE STAR RATED including provn of fan hook made of MS of required size and shape,hanging with the help of down rod upto 04 feet and connecting with provn of 3 core copper cable of size 1.5 sqmm from ceiling rose to fan complete all as specified and directed. Make:- Khaitan/Havells/Crompton/Bajaj/Usha

S&F ceiling fan of 1400 mm sweep,220-240 volt,AC,50 Hz, 290-320 RPM with air delivery of 245 cmm or more including provn of fan hook made of MS of required size and shape,hanging with the help of down rod upto 04 feet and connecting with provn of 3 core copper cable of size 1.5 sqmm from ceiling rose to fan complete all as specified and directed. Make:- Khaitan/Havells/Crompton/Bajaj/Usha

S&F of stationery storage type electric BEE 5 star rated hot water geyser of capacity 25 ltr to operate on 230 volts AC, vertical type, working pressure min 0.8 Mpa with feroglas lined coated tank, magnesium anode, adjustable thermostat, enamel coated incology heating element 2 KW, ABS plastic body including 4 nos full threaded faster of size 100 X 10mm with 2 no washer, water connection with 02 nos flexible steel hose pipe of size 15mm, 450/600mm length hot series complete all as specified and directed. .Make :- Havells/ Racold/ Bajaj/ Cromption

M&L for sub main wiring with 06 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 06 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

M&L for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

S&F in replacement of sheet metal enclosure distribution board triple pole and neutral (VTPN), AC, 440 volt, 04 way with 200 Amp rated copper bus bar and metal door with IP 54 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed Make :-Legrand, or equivalent in Hager or Schneider as approved by GE and comprising of the following:- (a) MCCB, 63 Amp, 04 pole, AC, 415 Volt of 16 KA breaking capacity complete - 01 No. Make :-Legrand or equivalent in Hager or Schneider as approved by GE. (b) MCB, SP, AC, 240 volt of 06 to 32 Amp, "C" curve, 10 KA breaking capacity - 08 Nos. Make :-Legrand or equivalent in Hager or Schneider as approved by GE.

Supply, laying, testing and commissioning LT underground XLPE insulated, armoured heavy duty underground electric cable with aluminium stranded conductor, 1100 volt grade, cross section area 25 Sq mm, 4 core complete all as specified and directed.(Note:- Excavation & Earth work shall be measured and paid separately under the respective items.)

Supply, laying, testing and commissioning LT underground XLPE insulated, armoured heavy duty underground electric cable with aluminium stranded conductor, 1100 volt grade, cross section area 35 Sq mm, 4 core complete all as specified and directed.(Note:- Excavation & Earth work shall be measured and paid separately under the respective items.)

M&L for sand cushioing for protection of cables complete all as specified and directed.

Supplying & laying burnt clay fly ash bricks designation 75, over LT cable laid flat for protection of cable complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600X600X6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to the GI strip 25X4mm by means nut bolts, cheak nuts and washer of the GI earth wire protected by provision of Gi light grade pipe 40mm including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregated with 40 mm thick cover with RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25X25X3mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, taste point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/demse soil, returning filling in and removal of surplus soil to a distance not exc than 50 mtr all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point including testing on completion complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600X600X6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to the GI wire of 4mm dia means nut bolts, cheak nuts and washer of the GI earth wire protected by provision of GI light grade pipe 40mm including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregated with 40 mm thick cover with RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25X25X3mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, taste point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/demse soil, returning filling in and removal of surplus soil to a distance not exc than 50 mtr all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point including testing on completion complete all as specified and directed.

Supplying & laying GI pipe, 40mm dia, light grade for cable protection at road crossing etc including necessary road cutting and making good with PCC 1:2:4 type B-1 using 20mm graded stone aggregate, 100mm thick or fixing on wall/poles of any type secured with clamps complete all as specified and directed.

Boring of road for laying of pipe not exc 90cm below ground level complete all as specified and directed.

M&L for point wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic ISI PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick with 3 mm thick plastic laminated sheet top cover, brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed for one light / fan point controlled by one, one way switch 06 Amp including taking down carefully existing copper/aluminium point wiring gs such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc.complete all as specified and directed.

All as per serial item No 48 here-in-before but one 3 pin, 06 Amp ISI socket outlet point on independent board controlled by one, one way switch 06 Amp.

All as per serial item No 48 here-in-before but one 3 pin, 06 Amp ISI socket outlet point on same board controlled by one, one way switch 06 Amp.

All as per Serial Item No 48 here-in-before but point wiring with 2.5 Sq mm single core FRLS cables and earth continuity wire of 1.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

S&F switch piano flush type, 06 Amp, ISI merk, single pole, one way, 230 Volt complete all as specified & directed.

S&F socket outlet , 3 pin, 06 Amp, ISI mark, flush type, 230 volt complete all as specified & directed.

S&F switch socket combination outlet , 3 pin, 06 Amp and 16 Amp flush type, ISI mark, universal, 230 volt, four hole complete all as specified & directed.

S&F in replacement of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

S&F electronic ceiling fan regulator with rotary step, two module, humfree, AC, 240 volt, 100 Watt and duly ISI marked complete all as specified & directed.

S&F ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed.

S&F in replacement of LED mirror light fitting, 14 Watt, 2 feet long with IP 20 protection comprises of aluminium extruded channel, frosted diffuser, integrated electronic driver, etc and all accessories pre-wired including connecting up complete all as directed. Make : Crompton Cat Part NO LCL-14-CDL or equivalent in Havells / Philips as approved by GE.

S&F decorative LED lighting fixture with extruded aluminium, heat sink, environmental friendly, energy efficient ready to use suitable for 4' LED tube complete all as specified and directed. Make: Havells Cat Part NO REGALBATTENT8UPTO1X22WSSBSWH or equivlent in CG/Philips as approved by GE.

S&F in replacement of single side connection LED T8 tube rod 20 Watt with PC body and diffuser, >2000 lumen, 6500K of four feet long into existing T8 conventional fluorescent tube light fitting after changing the necessary electric connections as required at site complete all as directed. Make : Havells / Philips / Crompton.

S&F in replacement of recesses mounted 2'x2' LED ceiling light fitting 36 Watt, 3650 lumen, 6500K, with IP 20 protection comprises of CRCA housing, high efficiency diffuser cover, electronic driver, etc and all accessories pre-wired including connecting up complete all as specified & directed. Make : Havells, Cat No : Endura Slim Pro Plus 2X2 or equivalent in Crompton/Philips as approved by GE.

S&F brass made double light bracket with 130mm x 95 mm, decorative oval base, two brass arm 305mm, length, both tipped with decorative brass leaf and provided with 52mm length x 34 mm dia. galleries with flowers at top and with 2 pin brass holders inside, frosted glass shades 155mm x 129mm finish: black nickel plated, alongwith two 05W LED bulbs complete all as specified and directed by EIC. Make Mepro, Cat No. MBBD-900 or equivalent in Philips/Havells/Crompton.

S&F in replacement of integrated LED bulk head fitting 12 Watt LED lamp, 60 lumen, 6500K with IP 66 and IK 09 impact resistance protection comprises of high pressure die cast aluminium housing, polycarbonate cover etc complete all as specified and directed. Make: Philips Cat No : WT202W LED6S CW PSU S2 PC or equivalent in Havells/Crompton

S&F wall fan, 450mm sweep, more than 1400 RPM, air delivery 100 CMM, 220-240 volts, AC, 50 Hz complete all as specified and directed. Make: Almonard Tempest Mark-II or eqivalent in Orient/Cropton.

S&F in replacement of sheet metal enclosure distribution board, single pole and neutral, AC, 240 volt, 08 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed. Make :- Legrand, Cat No. 5076 11 & 5079 13 or equivalent in Hager, Cat No : VYS08D & VYS08E or Schneider, Cat No : A9HSND08 & A9HSND08WB.

S&F in replacement of MCB, DP, AC, 240 volt of 40 Amp capacity "B" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. Make :- Hager, Cat No : NBN263N or equivalent in Schneider/Legrand.

S&F in replacement of MCB, SP, AC, 240 volt of 6 to 32 Amp capacity as ordered "B" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. Make :- Hager, Cat No : NBN106N to NBN132N or equivalent in Schneider/Legrand.

S&F in replacement of MCB, SP, AC, 240 volt of 6 to 32 Amp capacity as ordered "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. Make :- Legrand, Cat No. 4085 87 to 4085 95 or equivalent in Hager, Cat No : NCN106N to NCN132N or Schneider, Cat No : A9N1P06C to A9N1P32C.

S&F in replacement of LED security light fitting 36 watt, 3500 lumen, 5700K with IP 65 protection comprises of a pressure die cast aluminium housing, heat resistance toughened glass, LED lenses, surge protector, electronic driver, etc and all accessories pre-wired including connecting up with PVC insulated copper conductor cable 1.5 Sq mm, 3 core as required for connections and 32 mm bore light grade G. I. tube mounting bracket of 1.5 metre in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as directed. Make : Philips, Cat No : BRP409 LED CW 036 MR FG S1 PSU GR or equivalent in Crompton / Havells.

S&F terminal junction box with including nut bolts with iron clamp out door dust and vermin proof fabricate with 1.6 mm thick MS sheet encloser 200X 250X150 mm including neutral link and 4 nos 230 volts 63 amps bus bar for house connection with 2X10 SQ mm copper conductor multi standard and connecting insulator including two coats of synthetic enamel paint over a coat of metal primer complete all as specified.

HS ASSOCIATES

Supreme Builders