Augmentation and Revamping of washroom and toilets located in production and service facilities at BRIT Vashi complex

Amount

Supplying, stacking and laying of 230 mm thick rubble soling stones as under floor base including packing with smaller stone and compacting, ramming including spreading and consolidation of blinding material, moorum etc. complete all as per specifications and as directed by the Engineer-in-charge.

Providing and laying in position Cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20mm) including consolidation, finishing, curing etc. complete as per drawings and specifications but excluding the cost of form work shuttering, centering and steel reinforcement at all levels.

Providing Reinforcement steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings. Steel supplied by the contractor. Using TMT bars of specified grades of all sizes. TMT bars to be supplied by the contractor from the own plants of SAIL, RINL or TATA make only using virgin materials.

Providing, Centering, shuttering form work using steel plates, timber planks for all types of structures including necessary strutting, proping, staging, supports, bracings etc. and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels. a) For Sub Structure.

For Super Structure.

Providing and laying in position Reinforced cement concrete (RCC) of Grade M-30 using 20 mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to plinth level.

Providing and Laying Autoclaved Aerated cement block masonry of approved make with specified thick AAC Blocks in Super structure above plinth level up to 20 m height in cement mortar 1:4 (using crushed sand). The rate shall also include providing and placing in position 2 nos of 8 mm dia bars at every third course of the masonry work.

Providing, supplying, cutting, welding, fabricating, hoisting and fixing in position structural steel members like trusses, purlins, posts etc. using MS hollow / circular / square / rectangular tubular sections including appling a coat of Zinc chromate primer of approved make all as per specifications, drawings and as directed by the Engineer in charge.

Providing and fixing precoated Galvalume Roofing profile sheets of approved size, shape and pitch up to and including single length of 12.00 met. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 X 55 mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as directed by the Engineer-in-charge. Galvalume sheet roofing 0.50 mm thickness in single sheet.

Providing and fixing UV stabilised fibre glass reinforced plastic sheet roofing/vertical lines up to any pitch including fixing with ploymer coated 'J' or 'L' hooks, bolts and nuts 8 mm dia. G.i plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. the sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified and as directed by the Engineer-in-charge. 2.0 mm thick corrugated (2.5" or 4.5" or 6")or step down (2" or 3" or 6") as specified.

Providing and fixing precoated Galvalume roofing accessories using self drilling / self tapping screws or with polymer coated J or L hookes, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete. Roofing accessories of galvalume sheet up to 600 mm total width for ridges, gutters, aprons and flashings.

Providing 20 mm thick Plastering using Ready mix external plastering compound of approved make for external faces of brick work / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 meters height complete. All as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge. Note: Only M.S Scaffolding (H- Frame) is allowed where required, bamboo or any other type of scaffolding is not allowed strictly for saftey purpose.

Providing 15 mm thick Internal plaster in CM 1:4 without cement punning (using crushed Sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete. Note: Only M.S Scaffolding (H- Frame) is allowed where required, bamboo or any other type of scaffolding is not allowed strictly for saftey purpose.

Marble stone flooring/door/window framing using Udaipur Green Marble with not less than 18 mm thick marble slabs over 20 mm thick base of cement mortar 1:4 (using crushed sand) laid and placed with grey cement slurry including filling the joints with matching white cement slurry rubbing and polishing complete all as per specifications, drawings and as directed by the Engineer - in - charge.

Extra for providing edge moulding to 17 mm thick marble stone / Granite Slab counters, Vanitis etc. including machine polishing to edge to give high gloss finish et. Complete as per design approved by Engineer-in-charge. 1) Marble Work

Supplying, fixing and concealing the following diameter ASTM nontreaded UPVC sovent weldedpipes as per ASTM D-1785 and fittings as perASTM D-2466 and ASTM D-2467 (white or off white colour) UV stabilised pipe of specifiedclass consisting following item i) Supplying & fixing ASTM UV stabilised non treaded UPVC sovent welded pipes as per ASTM D-1785 and fittings as per ASTM D-2466 and ASTM D-2467 . ii) Laying and concealing the pipe and specials for water supply, waste and over flow line by cutting 75 mm X 75 mm grove on the wall and filling the grove with cement mortar mixed with water proofing compound, after laying and testing the pipe line including making leakproof threaded joints using fusion welding etc. including pipe cutting, cleaning, marking etc. iii) Testing the pipe line to a hydraulic pressure as per manufacturers cataglouge for leak proof joint or as per relevant code iv) Making leak proof threaded/welded joints. including cutting the pipe, cleaning, marking,heating, welding, cooling etc. and the cost of jointing materials. v) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipeline and reinstating all the damage to itsoriginal condition. Schedule 40 Pipes and Fittings of Approved make. a) ¾" n.b

Supplying & fixing on Exposed surfaces thefollowing dia. ASTM nontreaded UPVC soventwelded pipes as per ASTM D-1785 and fittingsas per ASTM D-2466 and ASTM D-2467 (whiteor offwhite colour) UV stabilised of specifiedclass, consisting following items of work:- i) Supplying & fixing ASTM nontreaded UPVCsovent welded pipes as per ASTM D-1785 andfittings as per ASTM D-2466 and ASTM D-2467. ii) Laying and fixing the pipe and specials onexposed surfaces to correct line, level and plumbfor water supply line, overflow and vent usingM.S. nails/screws, rawl plugs, wooden guttiesand branded clamps of Supreme make metalclamps with Rubber seal Supreme Cat. no.RH2MPC series the pipeline exposed as per thesite requirement. iii) Testing the pipe line to a hydraulic pressureas per manufacturers cataglouge for leak proofjoint or as per relevant code. vi) Cutting or making hole or chases in RCC orbrick work structure such as wall, column,beam, slab, chajja, dado etc. for passing the pipeline and reinstating all the damage to itsoriginal condition. v) Providing and fixing UPVC weldable /threaded fittings such as Union, Nipples,Bendes, Elbows, Tees, Reducers, End caps,Couplers, Adaptors, Saddles, Plugs, Tankconnectors, Expansion loops, Bypass bends,flange, Flange attapter etc. Schedule 40 Pipes and Fittings of Approved make Note:- The rate shall also include for UPVC pipe line &specials required for making connections withthe existing GI / PP-R / UPVC pipe line laid byother agency. Threaded fittings shall be of BrassThreaded only. a) ¾" n.b

Providing and Fixing UPVC (white or off white colour) Ball valve with stainless steel ball of Approved make suitable for pipe pressure class with material and labour, making water proof joints, including cost of jointing material and UPVC specials if required and testing the joints. etc complete as per directions of engineer-in-charge. a) ¾" n.b

Providing and fixing 1st quality ceramic glazed wall tiles confirming to IS 15622 of approved make, shade and colour of size ranging from 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm confirming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge over a bed of 20 mm thick bed of cement mortar 1:4 (using crushed sand), and jointing with grey cement slurry including pointing with white cement based tile grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge.

Providing and fixing white vitreous china flat back half stall urinal size 580x380x350 mm / 610 mm of approved make Aquaseal model with Push cock of approved make,with CP brass flush pipe unions, heavy quality C.P. brass spreaders, C.P waste coupling with dome grating, clamps complete all as per specifications drawings and as directed by the Engineer-in-charge.

Providing and fixing indian water closet (Orissa pan) of approved make with 100 mm China ware P or S tarp, One no. 10 litre high level or low level white PVC flushing cistern with flush pipe and bend with manually controlled device (handle lever) confirming to IS: 7231, PVC 15 mm inlet connection with all fittings and fixtures complete including all connection, embeddding in position commissioning, cleaning etc.all as per drawings and specifications and as directed by the Engineer - in - charge White vitreous china orissa pattern W.C. pan of size 580 X 440 mm

Providing and fixing white vitreous china European type water closet with 'P' or 'S' trap with solid seat and lid of approved make, 10 litre low level white PVC flushing cistern with manually controlled device (handle lever) confirming to IS:7231, flush bend, fixing EWC with C.P brass screws, 15 mm PVC heavy quality inlet connection of 450 mm long, including testing, commissioning and cleaning etc. complete all as per drawings and specifications and as directed by the Engineer - in - charge E.W.C pan in White colour with ISI marked white solid plastic seat and lid

Providing and fixing vitreous china wash basin of approved make and colour with C.I brackets, 15 mm C.P brass pillar tap of approved make, 15 mm X 600 mm long PVC inlet connection, 32 mm heavy quality C.P brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the engineer - in - charge White vitreous china wash basin size 550 X 400 mm / 550 X 420 mm and equivalent sizes with single 15 mm C.P. brass pillar tap

Providing and fixing C.P brass Bib cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer - in - charge 15 mm dia bib cock of approved type and make

Providing and fixing C.P brass Stop cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer - in - charge (A) 15 mm n.b CP Brass concealed stop cock of approved make

Providing and fixing C.P brasss Angle cock of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer - in - charge 15 mm n.b CP brass Angle cock of approved make

Providing and fixing 15mm C. P brass 2 in 1 bib cock and angle cock combiination of heavy quality of approved make as per specifications and as directed by the Engineer-in-charge

Providing, supplying and fixing JET spray with 1.00 meter long flexible tube connection in european/Anglo indian water closet under seat cover fixtures complete all as specified and as directed by the Engineer-in-charge.

Providing and fixing stainless steel toilet paper holder recessed type of approved make and type with S.S screws as directed by the Engineer-in-charge complete.

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

Providing and fixing CP Brass 100 mm dia shower rose with shower arm of specified make as per specifications and as directed by the Engineer-in-charge complete

Supplying & fixing in position at all floors and location 35mm thick of following type PVC foam board panel (integrated sheets) with 3mm thick PVC lipping alround in the form of flush door shutters manufactured by M/s. Jain Irrigation Systems Ltd. ( Ex-cel sheet) ply facing on bothsides of approved colour, solid section, extrudedrigid, light weight sheet with fine and homogeneous closed cell structure with smooth,glossy, hard surface finish on both sides, whole shutter unit shall be clipped by aluminiumsection (which shall be paid in relevant item),fixing shutters in position to pressed steel doorframes/ wooden frames/ granite frames/Aluminium frames [door frames (choukhat) shallbe paid separately under relevant item] at all floors by cutting/ planing required if any including providing & fixing with wooden nos.100 mm S.S. hinges and 2 nos. 150mm SS bow handle with back plate including finishing all edges smooth with mixture of PVC+C188 powder & solvent etc. all as per specifications,drawings & as directed by the Engineer in charge. i) The entire door shall be a joint lesss hutter.Cost of wastages if any shall be included in quoted rates. ii) Exact dimensions of shutter shall be measured to suite door frame size before manufacturing. iii) Quoted rate shall inclusive of additional fittings and fixtures required by manufactures if any for the complete unit. a) For Door type D3 of approximate size 700mmx 2100mm with 35 mm thick factory made PVC integral free foam sheet single leaf side hung door shutter in form of flush finish door

Providing and fixing IS:3564 marked aluminium die cast body universal Hydraulic door closer of approved make with necessary accessories and screws etc. in wooden doors/steel doors with necessary bolts and nuts complete as per specifications and as directed by the Engineer - in - charge.

Providing and fixing anodised Aluminium work doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make confirming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass/ stainless screws all complete as per drawings and directions of Engineer - in - charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc.(fitting glazing and panelling shall be paid for seperately) Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Providing and fixing following type of approved quality glass panes for doors / windows /ventilators, of M/s. Modiguard/ M/s. Saint Gobain and fixing with aluminium frame work including fixing aluminium channel beading and adjustable louvers frame (to be paid underrelevant item) and providing and fixing with 2way EDPM gasketing ,to ensure water and airtightness and neoprene cushions /gasket accommodated in grooves, necessary bronzeanodized screws etc., all complete generally asper drawings specifications and as directed bythe Engineer in Charge. 5mm thick bajra glass for louvers of approved colour and shade

Providing and fixing 6 mm thick mirror of size 600 X 450 mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P brass screws and concealed washers complete all as per specifications and as directed by the Engineer-in-charge.

Providing uPVC Floor Trap / Nahani Trap of following size having not less than 40mm effective water seal fixing the trap in position and connecting with waste water pipe by cement solvent / as per manufacturer's recommandation, embedding the trap in cement concrete 1:2:3 to correct level and gradient, providing and fixing 200 x 200 mm size top tile with central strainer & flat cover / flush strainer, closing the side inletes with plugs if required etc. all complete as per specification and as directed by E.I.C Multifloor trap of 110 x 75 x 50 size of Approved Make similar to Supreme make Cat No.NSPHMTS04L / NSPHMT005L with top tile Supreme make Cat No. NSPHTT201L /NSPHTT200L, Mat finish heavy quality

Providing and fixing PVC rain water pipes conforming to relevant IS type B and PVC SWR fittings & specials conforming to relevant IS including jointing with seal ring / With PVC solvent adhesive including fixing in walls using clamps etc complete all as per drawings, specifications and as directed by the Engineer-in-charge SWR PIPE 90 mm O/D

SWR PIPE 110 mm O/D

Providing, laying to the slope specified and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the order of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete excluding excavation and refilling which will be paid under relevent Item 100 mm diameter stoneware pipe

150 mm diameter stoneware pipe

Providing and fixing square mouth S.W. gully trap complete with CI grating and brick masonry chamber with water tight C.I cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design 150 x 100 mm size gully trap "P" type

Providing and constructioning inspection chamber of internal size clear dimension of 900 X 600 mm in 230 thick brick masonry with cement mortar 1:4 over a bed of 150mm thick 1:4:8 cement concrete foundation, plastering with cement mortar 1:4 20 mm thick on inside, out side and all exposed surfsces finished with a floating coat of neat cement, brick corbelling at top to provide opening of 900 X 450 mm, embeding the frame and cover with cc 1:2:4 concrete, and fixing cast iron steps if necessary at 300 mm intervals complete. Depth of chamber not exceeding 900 mm. (Excavation, soling, cast iron cover and C.I steps will be paid separately under relevant item.)

Providing & fixing precast EVERLAST Composite Manhole covers as per approved by Compitant athority/ E.I.C tested as per IS:1726. with engraved name of department and year as specified/approved, includingcost of necessary hardware, 1:2:4 grade concret forfixing frame, bed block (bearing course) and cappingincluding necessary form work and CM 1:2 mortar forfixing the frame & for plastering exposed surfaces ofconcrete bed block (bearing course) and cappingfinished smooth with floating coat of neat cemenetc., complete as per specifications, drawings and asdirected by the E.I.C. Rectangular Medium duty ( Grade MD - 10designation as per IS:1726) frame and cover 900 x 600 mm of approved colour by EIC

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made with strong vibratory compaction and approved size, shape, design laid in required colour and pattern over and including 50 mm thick compacted bed of crushed sand, filling the joints with crushed sand etc. all complete as -per the direction of the Engineer-in-charge

Providing and applying white cement based wall putty of approved make over concrete or plastered surface up to 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer - in - charge.

Providing and painting with 1st quality Acrylic washable distemper (ready made) with two coats of approved make and manufacturer and required shade and colour, including scaffolding, preparation of the surfaces, etc. Including a coat of approved cement primer as per manufacturers specifications and as directed by the Engineer - in - charge. Note: Only M.S Scaffolding (H- Frame) is allowed where required, bamboo or any other type of scaffolding is not allowed strictly for saftey purpose.

Providing and painting two coats of synthetic enamel paint on steel surfaces of approved brand and manufacture to give an even shade over a primer coat including preparation of the surfaces, scaffolding complete. As per specifications and as directed by the Engineer - in - charge Note: Only M.S Scaffolding (H- Frame) is allowed where required, bamboo or any other type of scaffolding is not allowed strictly for saftey purpose.

Providing, applying and finishing walls with two coats of premium fine textured exerior paint of required shade over new work including base coat of water proof cement paint, preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge Note: Only M.S Scaffolding (H- Frame) is allowed where required, bamboo or any other type of scaffolding is not allowed strictly for saftey purpose. On Plain plastered / concrete sufaces

Disposing off the surplus excavated materials and debris by mechanical transport with all lead at nearest approved disposal ground of NMMC including all lifts, loading, unloading all as per guidelines of Construction and Demolition (C&D) waste management plan as approved by NMMC & as directed by the Engineer in Charge. i) Voids @ 20% for soils and 50% for soft / hardrock shall be deducted from fully loaded truck measurements to arrive at the net quantity for payment, in case direct measurement is not possible. ii) Royalty for excavation, transportation, filling of earthwork etc. including obtaining permission from statutory authority, if any shall be borne by the contractor.

Carrying out civil maintenance and PH works like carpentary job, plumbing job, welding job, painting job for non scheduled items as per direction of Engineer-in-charge. 1) Each job shall be carried out by qualified person having appropriate experience. 2) The contractor shall deploy one person for each job for minimum 8 1/2 in a one day with 30 minutes of break. 3) Measurement will be per job basis. a) Miscellaneous job

Electrician job

Plumbing job

Providing and fixing of Concealed PVC boxes of size 3"X3" to 6"X3" for switches and fan regulators including supply of PVC boxes, cut outs for switch and sockets to be made as per site conditions, finishing the wall to normal condition.

Providing and fixing of Concealed PVC boxes of size 8”x 10” for switches and fan regulators including supply of PVC boxes, cut outs for switch and sockets to be made as per site conditions, finishing the wall to normal condition.

Providing and fixing of 5Amps. Piano type switches in the PVC box including the cost of switches, Testing and commissioning.

Providing and fixing of 15Amps. Piano type switches in the PVC box including the cost of switches, Testing and commissioning.

Providing and fixing of Concealed type 5Amps. Socket including the cost of Socket, Testing and commissioning.

Providing and fixing of Concealed type 15Amps. Socket including the cost of Socket, Testing and commissioning.

Supplying and wiring in the available concealed conduit pipes with 3 x 1.5 mm2 wires (Red Colour for Phase, Black for Neutral and Green for Earthing) including the cost of wires, Connecting as required to relevant switches / sockets, light or power points, testing and commissioning.

Supplying and wiring in the available concealed conduit pipes with 2 x 2.5 mm2 and 1 x 1.5 mm2 wires (Red Colour for Phase, Black for Neutral and Green for Earthing.) including the cost of wires, Connecting as required to relevant switches / sockets, power points, testing and commissioning.

Supplying and wiring in the available concealed conduit pipes with 2 x 4.0 mm2 and 1 x1.5 mm2 wires (Red Colour for Phase, Black for Neutral and Green for Earthing.) including the cost of all accessories, Connecting as required to relevant switches / sockets, power points, testing and commissioning.

Providing and fixing of PVC Casing Capping for Wiring (25mm, Heavy duty) in walls and ceiling, including the cost of all accessories and making the wall good.

Dismantling doors, windows and clear storey openings (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) of area 3.00 Sq.M and below.

Dismantling flushing cistern of any size including stacking of useful materials near the site and disposal of unserviceable materials within 100 m lead.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead for thickness of tiles above 10 mm and up to 25 mm.

Dismantling old plaster / skirting carefully , raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100 m lead.

Dismantling G.I pipes of all diameter external work including excavation and refilling trenches after taking out pipes manually / by mechanical means including stacking of pipes within 100 m lead as per direction of Engineer-in-charge

Dismantling the following dia of C.I pipes including excavation, taking out the pipes manually / by mechanical means, breaking lead caulked joints, melting of lead, making into blocks including stacking of pipes within a lead of 200 m as per direction of Engineer-in-charge 75 mm Dia to 200 mm Dia C. I pipe

Dismantling C.I pipes of following dia in shafts / open piping including taking out the pipes manually, breaking lead caulked joints, melting of lead, making into blocks including stacking of pipes within a lead of 200 m as per direction of Engineer-in-charge 75 Dia C. I pipe

100 Dia C. I pipe

Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and dispoal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

M/s. Shiv Langeshwar Enterprises

M/S. BALAJI CONSTRUCTION