Thanjavur District - Thanjavur Block - Construction of Public Distribution Shop at MGR nagar in Pillaiyarpatty panchayat under MLACDS 2024-2025

Amount

Construction of Public Distribution Shop @ MGR nagar in Pillaiyarpatty panchayat.

Earth work Excavation and depositing on bank with initial lead and lift in all classes of soil except hard rock requiring blasting including all labour charges etc.,complete for foundation

Supplying and Filling foundation and basement with M.Sand in layers not more than 15cm . Thick well ramed, watered and compacted Complete complying with stanard specification.

Cement concrete 1:4:8 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Brick work in cement mortar 1:5 mix using country bricks 83/4"x41/4"x23/4" including cost and conveyance of all materials to site and all labour charges etc complete (Below basement)

Brick work in cement mortar 1:5 mix using country bricks 83/4"x41/4"x23/4" including cost and conveyance of all materials to site and all labour charges etc complete (Above basement)

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists(Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items.(RCC floor slab, roof slab, Rectangular/ square, Tee/ Ell beams, Lintels, staircase waist slabs, Landing slabs, Landing beam, Portico beam etc., ). (Below basement)

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists(Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items.(RCC floor slab, roof slab, Rectangular/ square, Tee/ Ell beams, Lintels, staircase waist slabs, Landing slabs, Landing beam, Portico beam etc., ). (Above basement)

Supplying and Fabricating and placing in position MS steel or ribbed for steel for all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with stanard specification.

Reinforced Cement concrete 1:1.5:3 using 20mm ISS HBG metal for all RCC item of works excluding cost of Rein forcement and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or roof slabs wherever necessary and bearing surfaces of walls , sides and bottom of the slabs, beams etc., shall be finished smooth with cement mortar 1:3, 12mm thick. and with kraft paper without claiming extra as directed by the departmental officers complete complying with standard specifications.

Providing granolithic flooring with CC 1:2:4 mix 25 mm thick including cost and conveyance of all materials to site and all labour charges etc complete

Paving the flooring with special type of flooring tiles (Cement based Hydraulically pressed Anti skid tiles (20mm thick) in CM 1:3, 20mm thick including cost and conveyance of all materials to site and all labour charges etc complete.

Floor finishing in Cement concrete 1:2:4 mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete.

Dadooing with glazed tiles of size 300 x 200 x 6mm including cost and conveyance of all materials to site and all labour charges etc complete

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work.

Plastering with CM 1:3,10mm thick inculding cost and conveyance of all materials to site and all labour charges etc.,complete

Plastering with CM 1:5,12mm thick inculding cost and conveyance of all materials to site and all labour charges etc.,complete

Finishing the top of roof with one course of pressed tiles of size 20x20x2cm with cement mortar 1:3 mix and pointed with the same oiled mortar including cost and conveyance of all materials to site and all labour charges etc complete

Distembering two coats with best approved colour with Priming Coat over the new plastered surface including cost and conveyance of all materials to site and all other labour charges etc complete.

Exterior emulsion two coats over priming coat inculding cost and conveyance of all materials to site and all labour charges etc complete

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc (Manually operated) Upto 8 Sqm - (M-0401)

Supply and fixing of mild Steel Doors of any size as per standard departmental specifications including cost and conveyance of all etc., complete.

Supply and fixing of mild Steel Window of any size as per standard departmental specifications including cost and conveyance of all etc., complete.

Supply and fixing of mild Steel Ventilator of any size as per standard departmental specifications including cost and conveyance of all etc., complete.

Painting two coats over new iron works using ready mixed enamel paint inculding cost and conveyance of materials and all labour charges etc.,complete

Providing and fixing of PVC rain water down fall pipe 110mm dia with necessary T W Clamps, Plug, Shoes, bend, Screws, nails etc., complete

Wiring with 2 x 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light / fan Point (for electronic regulator) (5 points per coil) (SD 25)

Wiring with 2 x 1.5 sq.mm. (22/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet cover for 5A 3pin non interlocking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point (SD 38)

Supply and run of 2 of 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains (SD 62)

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. (SD 110)

Supply and fixing of single box type 4'40 W fluorescent fitting complete with copper choke and condensor with TWround blocks on wall or ceiling with flu tube with PVC unsheathed FRLS copper leads from terminals to the fitting (SD 88)

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit (SD 125)

Supply and fixing of 4 way single phase DB of 16A / way with 16A, DP switch of 500V with metal clad (side handle) with fuse and neutral on suitable TW board with PWD earthing (SD 145)

Supplying and fixing following thickness of cuddapah slab 40mm thick for cupboard including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc., complete.

Supplying & Fixing in position of Indian type Water closet 580x440mm of approved quality inculding cost and conveyance of all materials to site and all labour charges etc complete

Provision for Water supply and sanitary arrangements

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT (M-0821)

25mm PVC pipe (M-0876)

25mm PVC Couplers (Mould) BIS 7834/1975 Part VI (WD-M0111)

25mm PVC Equal tee (Mould) BIS 7834/1975 (WD-M0113)

25mm PVC Elbow (Mould) BIS 7834/1975 Part VI (WD-M0112)

32mm PVC pipe (M-0877)

32mm PVC Elbow (Mould) BIS 7834/1975 Part VI (WD-M0112)

32mm PVC Equal tee (Mould) BIS 7834/1975 (WD-M0113)

110mm PVC pipe

110mm PVC Couplers (Mould) BIS 7834/1975 Part VI (WD-M0111)

110mm PVC Elbow (Mould) BIS 7834/1975 Part VI (WD-M0112)

110mm PVC Equal tee (Mould) BIS 7834/1975 (WD-M0113)

20mm GI Waste Not Tap (WD-M0615)

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

Ramprasath (BID ID -1534914)