Renovation of toilet near Committee Room and Ladies toilet in the main Block in the Building of College of Agricultural Engineering and Technology at CCS HAU, Hisar

Amount

Dismantling cement conglomerate/ terrazzo floors 25 mm to 50 mm thick including concrete base. (HSR 8.25)

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth (HSR 10.41)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling (HSR 14.1)

Providing and fixing ceramic tiles/ anti skid tiles of size 400 mm x 400 mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles (HSR 14.91) Note : tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colour, shades except burgundy, bottle green, black of any size of approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement coarse sand mortar 1:3 and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (HSR 14.92) (a) size of ceramic glazed tiles 200 mm x 300 mm

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.5)

White washing two coats (HSR 16.47)

Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and specials tees, bends, sockets elbows etc. inside building and testing etc. complete including cutting threading. {HSR 28.18(b)} INCLUDING COST OF SPECIALS (i) 15 mm internal diameter of pipe line

(ii) 20 mm internal diameter of pipe line

(iii) 25 mm internal diameter of pipe line

Extra for fixing and jointing union couplings in G.I and W.I pipe lines. {HSR 28.21} (b) 20 mm internal diameter

(c) 25 mm internal diameter

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. (HSR 28.24) (a) 11.43 cm thickness of walls

(b) 22.86 cm thickness of walls

Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I pipelines laid in the ground or inside buildings including cartage from divisional stores or nearest railway station to site of works. (HSR 28.29) © 25mm i/d

Making connection with the existing G.I branch main up to 40 mm size including cutting and threading pipe etc., complete excluding cost of tee and long screw, but including cartage of material to site. (HSR 28.34)

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type Orissa or orya water closet suite for sinking into floor, with raised foot treads complete with 100 mm H.C.I ‘P’ trap with or without vent as required and all other necessary fittings as fully described in item no. 30.1 above (without cost of C.I. high level flushing cisterns) (based on 30.2(a)(i)} (a) 580 mm (i) WHITE

Providing and fixing in position best Indian make European type water closet suite with concealed ‘P’ of ‘S’ trap with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item No. 30.3 above (without cost of C.I. high level flushing cisterns) {based on HSR 30.6(i)} (White)

Extra over item no. 30.3 to 30.6 for providing and fixing best Indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid. {HSR 30.13(i) (i) White plastic seat ( Solid)

Extra for providing and fixing 32 mm dia. G.I/ C.P flush pipe complete with accessories instead of 32 mm dia. Galvanised telescopic flush pipe with clips ( as required by the Engineer-in-charge) {HSR 30.15(b)} (b) 32mm dia C.P brass flush pipe

Providing and fixing in position best Indian make a range of two urinals large flat back or angular lipped front 610 mm high in vitreous china-ware with 5 lit capacity best Indian make C.I automatic flushing cistern with fittings and flush pipe etc. complete as fully described in item no. 30.25 above, {HSR 30.26(i)} Range of two urinals (i) White

Extra for providing and fixing vitreous automatic flushing Cistern including fittings and brackets of C.I. flushing cistern complete {HSR 30.37(b)(i)} 10 ltr. capacity cistern (i) White

Extra for providing and fixing standard size C.P. brass flush pipe complete with fittings instead of G.I flush pipe complete {HSR 30.38) (ii) For a range of two urinals

Providing and fixing 25 mm thick marble partitions for different type of urinals. {HSR 30.40(b)(II)(i)} (b) Vitreous Chainaware Partition Plate (II) LARGE SIZE 835 mm x 355 mm (i) White

Providing and fixing in position best Indian make (ordinary) lavatory suites consisting of Lavatory in vitreous china ware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary, R.S or C.I brackets for building into wall including painting;32 mm C.P. brass waste with C.P brass chain and rubber plug;15 mm C.P brass screw down pillar tap with jamnuts or couplings best design ( as approved by the Engineer-in-charge) all fittings best Indian make and; to the approval of the Engineer-in-chargeall brass work chromium plated and complete in all respects including cutting and making good the walls and floors and painting of fittings etc. (HSR 30.41) (iv) size 550 mm x400 mm with one no tap

Providing and fixing in position 32 mm dia G.I waste pipe embedded in wall or lead waste pipe (weighing 3.47 kg per meter and 2.8 mm thick) up to floor level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge) (HSR 30.48)

Providing and fixing in position best Indian make chromium plated brass bottle trap 32 mm diameter (HSR 30.50)

Providing and fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P brass screws ( as required by the Engineer-in-charge) complete including cutting and making good the walls etc. {HSR 30.71 (a)} Indian Make (i) 600mmx450mm

Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P brass screws and rawl plugs etc. complete including cutting and making good the walls etc. {HSR 30.73(a)(ii)} (a) C.P. BRASS (ii) two way

Providing and fixing in position 15 mm i/d C.P brass bib cocks of best quality ( as required by the Engineer-in-charge) {HSR 30.75 (c)} (c) bib cock

Providing and fixing in position C.P brass stop cock (as approved by the Engineer-in-charge) {HSR 30.76 (a)} (ii) concealed stop cock with flange

Providing and fixing in position best Indian make C.P brass inlet connection 15mm with 375mm pipe and C.P brass nuts. (HSR 30.83)

Providing and fixing in position H.C.I soil waste vent or antisyphonage pipes to I.S.I specifications of E.L.C manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floors etc. and making good to its original condition but excluding cost of lead jointing. (HSR 30.84) (a)100 mm i/d

(b)75 mm i/d

Providing lead caulked joints to H.C.I pipes and specials conforming to I.S.I specification of E.L.C manufacture or any other reputed firm including cost of lead yarn, fuel and tools etc. (HSR 30.87) (a)100 mm i/d

(b)75 mm i/d

Providing and fixing H.C.I. floor traps I.S.I. marked of the self cleaning design with C.P. brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under the around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors, etc., minimum depth of water should be 150 mm with a minimum seal of 50 mm. (HSR 30.89) (b) With 75 mm internal dia outlet

Cutting chase in brick walls in cement or in floor for embedding G.I. or H.C.I. pipe lines and making good the same to its original condition {HSR 30.95(a) (a)size 75 mm X 75 mm

Providing and fixing in position automatic brass ball valves in tanks {HSR 30.110(b)(iii)} (b) WITH PLASTIC BALL (iii) 25 mm internal diameter

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with H.C.I. grating 150 mm X 150 mm cast iron cover weighing approximately 7.26 kg. and frame clear opening 300 mm X 300 mm and outside size 330 mm X 330 mm and chamber including cost of all brick work in cement mortar 1:5 cement concrete 1:8:16 in foundations, and cement concrete 1:2:4 in coping around C.I. cover and frame et. With three coats of black bitumastic superior paint of approved manufacture on all C.I. work as per standard design, minimum depth of water should be 150 mm with a minimum seal 50 mm {HSR 30.114(b)} (b) 100 mm internal diameter H.C.I. gully trap

Providing and fixing HDPE WATER STORGE TANKS of sintex, diplas O.K. Supreme make with covers/ lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. {HSR 30.119) 500 ltr,. capacity

Supply of G.I. pipe ‘B’ class ISI marked of ‘Ravindra’/ ‘Jindal’/ ‘Parkash ( Surya)’/BST make {NS) (a) 15 mm internal dia

(b) 20 mm internal dia

(c) 25 mm internal dia

Supply of G.I. Union couplings of Unik / Unco make {NS} (a) 20 mm internal dia

(b) 25 mm internal dia

Providing and fixing in position PVC flushing cistern 8.0 ltrs. capacity of Hindware/Cera/perryware make ISI marked, white, alongwith fittings complete in all respect. (NS)

Supply of G.M. Peet valve (heavy type) of DRP/Leader/Bajaj make ISI marked. {NS} (b) 20 mm internal dia

Suraj Bhan Contractor