8177 ADDTN/ALTN AT MARITIME OPERATION CENTRE (MBI) P/A-3 AND PROVISION OF ALUMINIUM BASED PARTITION AND CERTAIN WORKS AT INSMA BLDG NO. P 49 AT NAVAL DOCKYARD MUMBAI UNDER GE (NW) KUNJALI

Amount

Dismantling stone slab and tiles of of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.50 mm graded aggregate) cement concrete as a leveling course on roof surfaces and coping etc complete all as specified and directed.

M&L for laying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on a coat of bituminous primer 0.25 Kg/Sqm on prepared surface of plaster as per manufacturer's instructions, manufactured by the same agency of APP membrane. The APP membrane shall be laid using torch on application with minimum 100 mm side overlap and 150 mm end overlap. The laying of membrane shall be got done through an authorised applicator of manufacturer of the membrane. The APP membrane shall be taken upto minimum 200 mm on vertial surfaces. The edge of the membrane shall be sealed with sealant complete all as specified and directed.

M&L for PCC type B-1, 1:2:4 (using 20 mm graded stone agg) as in lintels upto 1.5 M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof kerbs, water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and rubbishing off the premises etc complete all as specified and as directed.

M&L rendering 15mm thick in CM 1:6 on brick surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M&L rendering 5mm thick in CM 1:3 on concete surfaces as in ceiling finished even & smooth without using extra cement in ceiling.

M&L rendering 20mm thick in two coats(15mm inner coat 5mm finishing coat) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound on finishing coat in the proportion as mentioned in manufacturer's instructions including all as specified and directed. (Note: Water proofing compound to be measured and paid for separately).

Supply only integral water proofing compound complete all as specified and directed.

M&L for machine pressed Pavers Terracotta (coloured) cement tiles of size 300mmx300mmx25mm thick mix with grey cement and pigment laid over 20mm thick screed bed in CM 1:4 set and jointed and pointedin neat cement slurry in floors complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and disposing the rubbish to the out side of MD land.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick(square/Rectanglar) area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floor including 20mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for coloured glazed ceramic tiles 450x300x7 mm thick but as on vertical surfaces such as skirting/dado including 10mm thick rendering in CM 1:3 complete all as specified and directed..

M&L light shade double charged virified ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor including 20mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed...

M&L light shade double charged vitrified ceramic tiles 10mm thick (square /rectangular) polished, area of each tiles not exceeding 0.36sqm (600x600mm), but as on vertical surfaces such as skirting/dado including 10mm thick rendering in CM 1:3 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed...

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed..

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets etc complete all as specified and directed..

S&F Anodised aluminium snap grid size 605x605mm frame work for false ceiling complete all as specified and directed..

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed..

M&L for false ceiling made out of 600x600x 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and directed...

S&F 3 mm thick aluminium composite panel cladding plain of approved colour/shade to beam/column/slab incircular/rectangular shape inbcluding cutting, notching, bending to shape as required jointing with silicon gel of approved colour & aluminum tubular hallow section 25 x 25 mm not exceeding 900 mm C/C on exceeding column/beam/slab to hold APC cladding etc (Note : colour/pattern of ACP sheet shall be approved by Engr-in-charge)

S&F 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall vertically with screws and C/C deistane 30 CM to make PVC frame as per specification and drawing.

S&F PVC wall /ceiling paneling consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing.

Taking down chowkats or frames but n exc 1.5 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and directed..

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and directed..

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site. complete all as specified and directed..

S&F powder coated aluminium (minimum 25 micron thickness of coating) of various section as required for doors, sliding windows/ partion/Ventilator etc including fixing and making the frames for hinges glass/wire gauge etc. Complete incl all fittings like rubber beading, clips locking arrangement,in sliding shutter, sealant etc all as specified and as directed .

S&F aluminium grill with and including suitable aluminium anodised frame F/H section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, complete all as specified and directed..

S&F for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed complete all as specified and directed.

S&F 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and directed..

S&F Stainless steel butt hinges 100 mm complete all as specified and directed...

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed..

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; walkj ways, railings, frame work for water tanks and similar work conforming to Fe 290 Gd E-165 complete all as specified and directed..

S&F 12mm thick, toughened glass including itching etc for door shutters, partitions, shelves etc with and including fitting and fixtures such as glass handles ss studs, fittings for door pivots etc complete all as specified and directed..

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium ally sheet foundation box, main body with stainless steel cover, governing pivot made of bras, other parts made of mild steel heavy duty and fixed complete all as specified and directed..

S&F 100 mm size mortice lock with two lever (vertical type) brass body and fixed complete all as specified and directed..

S&F solar control film 25 micron reflective type sticked to glass panes as per instruction of manufacturer including removal of existing complete all as specified.

S & F Roller venetion blinds type made out of standard cloth of approved texture with necessary accessories etc complete all as specified and directed..

Taking up or down existing GI water tubing complete with all fittings of 15 mm bore complete all as specified and directed..

Taking up or down existing GI water tubing complete with all fittings of 20 mm bore complete all as specified and directed..

S & F 15 mm bore UPVC pipes of pressure rating 10 Kgf/cm2 fixed complete to walls, celing etc or in floors etc complete all as specified and directed..

S & F 20 mm bore UPVC pipes of pressure rating 10 Kgf/cm2 fixed complete to walls, celing etc or in floors etc complete all as specified and directed..

S&F fancy type CP stop/angle cock of 15 mm dia, screwed for iron pipe and fixed as per sample complete all as specified and directed..

S&F fancy type bib cock 15 mm dia, screwed for iron pipe and fixed complete all as specified and directed..

S&F fancy type CP Pillar taps 15 mm dia, cast copper alloy, with capstan heads, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed..

S&F 600mm PVC connections 15 mm size with PTMT nuts complete all as specified and directed..

S&F of vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to trap and drain (or outgoing pipe) and to flushing pipe, antisyphoage pipe etc complete all as specified and directed..

S & F floor mounted coupled water closet cistern for coupled WC with UF soft close seat cover, hinges fixing accessories set and accessories set, size 380x660x765mm, P or S trap complete all as specified and directed .

S&F PVC valveless syphonic action type ,flushing cistern Low level white, with inlet ball valve ,float and handle 10 Ltr capacity including brackets complete all as specified and directed...

S & F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed..

S&F wash hand basin vitreous china white (flat back) of size 550x400mm including bracket 15mm dia 32mm dia waste coupling and 32mm dia PVC waste pipe 90cm long etc. complete all as specified and directed..

S&F under counter wash hand basin vitreous china of white/coloured, size and design as per sample and directed by the Engr-in-Charge including fixing with fastner/ bracket 15mm dia 32mm dia waste coupling and 32mm dia PVC waste pipe 90cm long etc. complete all as specified and directed..

S&F vitreous china urinals, bowl type, flat back, size 465 X 355 X 265mm, white, with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in CM 1: 2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), fixed in repairs.

S & F for urinal pot with sensor Size 370x390x610mm Star white(Senso Art) complete all as specified and directed

S&F CP towel rail 600 mm long with round flange complete all as specified and as directed

S & F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed .

S & F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed .

S & F PVC (SWR) bends 110 mm complete all as specified and directed

S & F PVC (SWR) bends 75 mm complete all as specified and directed

M&L PVC (SWR) floor trap, plain with grating including jointing with solvent cement75 mm dia complete all as specified and directed .

M&L for applying 1 to 2 mm thick wall care putty for making the surface even & smooth complete all as specified and directed .

Preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of of primer complete all as specified and directed

M&L for preparation of newly plastered surfaces of ceiling and applying two coat of oil emulsion distemper over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall, soffits, facia roof and applying two coats of weeather acrylic base paint (100 % acrylic) over one coat of cement based or suitable primer with necessary scaffolding etc complete all as specified and directed

M&L preparation of old distempered surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying one coat of oil emulsion distemper on walls etc complete all as specified and directed .

M&L preparation of old decorated surfaces of walls, soffits, roof facia & applying one coat of weather proof acrylic based paint (100% acrylic) etc complete all as specified and directed

French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with two or more coats complete all as specified and directed

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint with necessary scafolding for high rise bldgs etc complete all as specified and directed

M&L for preparation of old painted wooden surfaes of any description over 10cm width or girth and applying one coat of synthetic enamel paint including external window with necessary scafolding for high rise bldgs complete all as specified and directed

S&F powder coated aluminum (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (fixed portions) with extruded builtup standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285,fixing with dash fastners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminum sections shall be smooth, rust free,straight,mitred and jointed mechanically wherever required including cleat angle,Aluminum snap beading for glazing/paneling,C.P. brass/stainless steel screws,all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

M&L for powder coated aluminium skeleton sliding door with one or more rebates inclusive of sliding channel, required ball bearing for sliding purpose, concealed locking arrangement and handles, sliding stopper bolts etc complete all as per directed by Engr-in-Charge.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy etc complete all as specified and directed

S&F 5.5 mm thick, sheet glass is ground or obscured or frosted, on one side ordinary quality in any size of pan complete all as specified and directed.

M&L for Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed

M&L 18/19 mm thick prelaminated particle board,interior grade,prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminum/timber frame work etc complete all as specified and directed.

S&F Aluminum (extruded section) body Door closer hydrau lically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg complete all as specified and directed .

S&F for 140mm long floor door stopper of aluminium body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and as directed

Taking down carefully old U/S point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, fan regulators, ceiling roses, lamp holders, brackets, ,removing material to store for keeping in safe custody and making good to disturbed surfaces complete all as specified and directed

M & L for concealed point wiring in repair with FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm size 1100 volts grade drawn through and including non metalic rigid PVC conduit not less than 25mm width with all accessories fixed on wall including FRLS PVC insulated, unsheathed multistranded copper onductor cable of size 1.5 sqmm as earth continuty conductor connecting to common earth dolly and PVC moulded box ISI marked for having the switches, switch sockets regulator etc complete all as specified for following:- One light point controlled by one switch

All as per item no. 84 above but for One ceiling fan/wall fan/exhaust fan point controlled by one switch complete all as specified and directed

All as per item no. 84 above but for One 5 Amps switch socket combination on independent board complete all as specified and directed

All as per item no. 84 above but for One 5A flush type switch socket point on same board complete all as specified and directed

M & L for concealed point wiring in repair with FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm size 1100 volts grade drawn through and including non metalic rigid PVC conduit not less than 25mm width with all accessories fixed on wall including FRLS PVC insulated, unsheathed multistranded copper onductor cable of size 2.5 sqmm as earth continuty conductor connecting to common earth dolly and PVC moulded box ISI marked for having the switches, switch sockets regulator etc complete all as specified for following:- One 15A flush type switch socket point on independent board

M & L for concealed point wiring in repair with FRLS PVC insulated unsheathed multi stranded copper conductor cable of 4.0 sqmm size 1100 volts grade drawn through and including suitable size PVC non metalic rigid casing and caping not less than 25mm width with all accessories fixed on wall including FRLS PVC insulated, unsheathed multistranded copper conductor cable 4.0 sqmm as earth continuty conductor, connecting to common earth dolly including required nos and size of modular box with cover plate frame in any module complete necessary electrical connections for each work station point comprising of 03 Nos. 5A and 01 No switch socket 15Amps complete all as directed.

S & F in repairs modular switch 1 way 6A, 1 module all as specified and directed. Make: Make: Legrand cat part No. 5734 00 or equivalent make in list of manufactures

S & F in repairs modular switch 1 way 16A, 1 module complete all as specified and directed. Make:Legrand cat part No. 5734 10 or equivalent make in list of manufactures

S & F in repairs modular socket, 6A - 2/3 pin combined 2 modules all as specified and directed. Make: Legrand cat part No. 5734 24 or equivalent make in list of manufactures

S & F in repairs modular socket 6/16A,2/3 pin, combined 2 module all as specified and directed. Make: Legrand cat part No. 5734 71 or equivalent make in list of manufactures

S&F in repairs for modular fan step regulator, 120W - 2 modular complete all as specified and directed. Make: Legrand cat part No. 5734 63 or equivalent make in list of manufactures

S & F in replacement of Ceiling rose, PVC/polycarbonate insulated body type, 3 terminal, 240 volts, 5 Amps complete all as specified and directed.

M&L for concealed submain wiring in repair with 2 runs of 2.5 sqmm and 1 run of 2.5 sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable with proper colour coding drawn through and including non metalic PVC casing & caping not less than 25mm width ISI marked with all accessories like PVC elbow, PVC Tee etc fixed on wall complete including connecting up complete all as specified and directed.

M&L for concealed submain wiring with 2 runs of 10 sqmm and one run of 10 sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable with proper colour coding drawn through and including non metalic PVC casing & caping not less than 25mm width ISI marked with all accessories like PVC elbow, PVC Tee etc fixed on wall complete including connecting up complete all as specified and directed.

M&L for concealed submain wiring in repair with 2 runs of 4 sqmm and 1 run of 4 sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable with proper colour coding drawn through and including non metalic PVC casing & caping not less than 25mm width ISI marked with all accessories like PVC elbow, PVC Tee etc fixed on wall complete including connecting up all as specified and directed.

M&L for concealed sub-main wiring with 2 runs of 6.0 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 6.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

M&L for concealed sub-main wiring with 4 runs of 10.0 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 10.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

S&F in repair LED recess mounted type fitting 36W 2'x2' CRCA LED Slim panel with recess mounting, powder coated white CRCA full glow LED panel including control gear and lamp complete all as directed and specified . Make: Phillips cat part No. RC383P LED 36S-6500 PSU OD WH PIR 2X2 SMART GLOW or equivalent make in list of manufactures

Supply and fixing in repair of LED 60W Street/building security light fittings with high pressure die cast housing with toughened glass and individual LED with secondary optics and IP66 protection complete all as specified and directed .

Supply and fixing in repair walll/surface mounted 20W LED batten fitting engineering plastic battern with white acrylic cover complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round/square block-02 Nos including connecting up with twin core copper conductor cable with suitable size complete all as specified and directed .

Supply and fix in replacement MS arms bracket 30 degree bend, 1.5mtr long for mounting one in nos street light fitting including clamps / nut / bolts & washer to brace the same properly with duly painted in synthetic enamel paint of two coat in silver colour complete all as specified and directed .

S & F MCCB, 415 volts, 3 pole of cap 160 Amps, 25 KA, DPX3 with fixed Thermal - setting and electronic earth leakage module of suitable size and making connections complete all as directed. Make - Legrand cat No 420055 or equivalent make in list of manufactures

S & F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting VTPN 12 way, 440 volts with bus bar rating 250 Amps, dust and vermin proof suitable for housing MCCB upto 160A 3 pole including required suitable size gland complete all as specified and directed .

S & F in repair MCB SPN 63 Amps, 10 KA Rupturing capacity complete all as specified and directed .

S & F in repair MCB SP 6 - 32 Amps, 10 KA Rupturing capacity complete all as specified and directed .

S & F in repair MCB SP 40-63 Amps, 10 KA Rupturing capacity complete all as specified and directed .

S& F in replacement of GI cable tray perforated type 2 mm thick of size 900x50mm ( Including pre fabricated GI clamp suitable for fixing/supporting ) with0.71mm thick aluminium sheet cover, alloy 31000 H4 in ridges, Hips vally gutter cable trucking for plain to be fixed on any wall (brick/stone) vertically/horizontally including all accessories complete bending, shaping, drilling,welding, cutting & all fixing arrangement complete etc complete all as specified and directed .

S& F GI cable tray perforated type 2 mm thick of size 450x50mm ( Including pre fabricated GI clamp suitable for fixing/supporting ) with0.71mm thick aluminium sheet cover, alloy 31000 H4 in ridges, Hips vally gutter cable trucking for plain to be fixed on any wall (brick/stone) vertically/horizontally including all accessories complete bending,shaping,drilling,welding, cutting & all fixing arrangement complete etc complete all as specified and directed .

S&F of PVC body exhaust fan of size 300mm sweep complete set with louvers connecting up including provn of three core flexible copper wire of size 23/0.0076 from ceiling rose to exhaust fan complete all as specified and directed.

Disconnecting and taking down the fan and Overhauling of ceiling fan any size and make, dismantling parts, properly cleaning/removing old existing grease oil and applying new oil grease, varnishing of winding, cleaning dust, rust and applying two coat white enamel paint over a coat of steel primer, assembling and refixing at same position complete all as specified and directed.

Supply and fixing of BLDC ceiling fan 1200mm sweep, BEE 5 star rated with remote complete all as specified and directed .

Disconnecting and taking down the fan and Overhauling of exhaust fan any size and make, dismantling parts, properly cleaning/removing old existing grease oil and applying new oil grease, varnishing of winding, cleaning dust, rust and applying two coat gray paint over a coat of steel primer, assembling and refixing at same position complete all as specified and directed .

Supply and fixing of wall mounted fan 450 mm size complete all as specified and directed

S&F in replacement of hanger clamp assembly with down rod up to 3 feet for hanging of ceiling fan with nuts,bolts,washers & split pin complete all as specified & directed .

S&F in replacement steel sheet enclosure double door type IP54 IK09 protection DB SPN 12 way, 240 volts AC factory made, suitable for housing MCB SPN along with 200 Amps copper bus bar complete all as specified and directed

Supply , fixing, testing in repairs of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 25 mm dia with 250 micron ( averaSchneider ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF Powerfill Loresco compound shall be supplied in 50 Pound Bag. ( 1 Bag of 50 Pounds required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set alongwith earth pit weatherproof incl complete all as specified and directed . Note : Back-fill compound shall not be mixed with any soil while pouring in the bore hole.

M&L in repair for 25x4 mm GI earth strip continuity conductor or main earthing lead fixed to wall or buried in ground or drawn in conduit/ pipe or fixed to panel body/motor body/any other equipment complete all as specified and directed .

M & L for 4mm GI wire earth continuity conductor or main earthing lead fixed to wall or buried in ground and fixed to panel/transformer alongwith 20mm gi pipe light grade for protection complete all as specified and directed .

Disconnecting & taking down old Unservicable cable & Supply laying & testing cable XLPE insulated screened, PVC bedded galvanised steel strip or wire armoured electric power cable (heavy duty) 100 volts grade with stranded copper conductor of size 50 sqmm 3.5 core in trenches/along wall/floor etc incl required material for fixing arrangement complete all as specified and directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep, 1400 RPM with louver complete all as specified and directed. Make : Usha cat No. TURBO HDEF1400RPM or equivalent make in equivalent make in list of manufactures

GANGAJAL (BID ID -3350897)