PROVN OF BAGGEGE ROOM FOR CAMP AREA AT AWC UNDER GE AWC MHOW.

Amount

Exacavation in trenches, n. exc 1.5m wide and n. exc 1.5 m in depth for foundation etc or for shaft ,wall, cesspits, manholes, pier holes etc. n. exc 10 Sqm on plan and n. exc 1.5m in depth in any type of soil etc complete all as specified and directed.

Description same as per Item No. 1.00 but depth exc. 1.50m but not exc 3.00m complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc 1.5 m above the starting point

M&L PCC 1:4:8 type D-2 using 40 mm graded aggregate as in mass concrete, foundation and any other location etc. complete all as specified and directed.

M&L for RCC (design mix) M25 ( 20 mm graded aggregates) as in foundations, including rafts, footings, foundation beam, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (design mix) M25 ( 20 mm graded aggregates) as in Columns, pillars, piers, posts, and struts complete all as specified and directed.

M&L for RCC (design mix) M25 ( 20 mm graded aggregates) as in Beams , cantilivers , bressummers , lintles over 1.5 M span complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in slabs supported on walls, beams, and columns complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beam, sides and soffits(if any) of foundation and plinth beams and similar work, vertical or to batter surfaces for rough finished flat surfaces of concrete, for fair finished surface of concrete complete all as specified and directed.

Use and waste of formwork rough finished surface of concrete as in Square, rectangular or polygonal to sides of columns, pillars, posts, struts, piers etc.complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beam, beam hauchings, bressummers, lintels, shelves etc. including supports, overhangs, etc, complete all as specified and directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizointal or slooping) for fair finished surface of concrete complete all as specified and directed.

Use and waste of formwork to edges of concrate flats, treads, breaks in floors, and roof n.exc 20 cm wide and sides of RCC/PCC bands in walls horizontal or sloping and similar work exc 10 cm but not exc 20 cm wide, for fair finished surface of concrete complete all as specified and directed.

S&F TMT bars 10 mm dia and over, cut to length, bent to shape as required incl cracking, bending spirally for hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed.

Description same as per Item No. 15.00 but 6mm to 8mm dia complete all as specified and as directed.

Description same as per Item No. 15.00 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed.

M&L brick work with fly ash modular bricks straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L 40 mm thick Damp proof course in cement concrete 1:2:4 type B-0 with incorporating integral water proofing compound in the manner specified by the manufacturer and in the proportions indicated, to horizontal or vertical surfaces including necessary formwork complete all as specified and directed. Note:- WPC will be measured and paid separately.

M&L rendering 10 mm thick on brick wall/cement block wall or concrete surfaces in cement mortar 1:6, surfaces finished even and smooth without using extra cement , complete all as specified and as directed.

M&L 10 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling surface finish even and smooth without using extra cement , complete all as specified and directed..

M&L Plastering 15 mm thick in two layers of 10 mm thick in bottom and 5 mm thick with WPC of top layer in Cement Mortar 1:4 on brick wall/cement block wall or concrete surfaces, surfaces finished even and smooth without using extra cement , complete all as specified and as directed. Note:- WPC will be measured and paid separately.

Supply only liquid water proofing compound all as specified and directed

M&L Preparation of new wall surface and apply one two of white wash on wall surface including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified and directed.

M&L for preparation of newly plaster surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

M&L preparing of newly plastered or unplastered surfaces of walls, cornices etc and applying two coats of cement base paint over one coat of priming coat complete all as specified.

M&L moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L 20 - 25 mm thick machine cut Kota stone slab in flooring or treads of steps over and including 20mm thick screed bed in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing complete all as specified and as directed. Note:- The size of Kota stone slab shall not less than 550 mm x 550 mm cut size, except the location where the balance portion remain less than size as specified above.

Description same as per Item No. 28.00 but as in riser of steps, skirting, dado and vertical surfaces including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar places, surface finished even and fair without using extra cement incl necessary use and waste of form work complete all as specified and directed.

S&F framed work such as grills, gratings, guard bars, railings etc, and similar work con-forming to Fe. 290 Gde E-165, complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete etc, and similar work con-forming to Fe. 290 Gde E-165, complete all as specified and directed.

S&F Mild steel 1.6 mm th plain, black sheet in wall cladding, steel gates and similar work, cut to size,welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S&F steel ventilators with top hung shutter including hinges, steel peg stay, complete all as specified and directed

S&F for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars,dovetailed or welded complete all as specified and as directed.

M&L Water proofing treatment on "Non approachable / non accessible roof" surface (Horizontal & Vertical surfaces) in following sequence through authorized applicator of the manufacturer all as specified and directed complete. (i) cleaning of new rendered surfaces properly and drying the surfaces. (ii) Applying a coat of oxidised bitumen based solvent primer @ 0.30 Kg / Sqm (iii) Laying 3 mm thick APP modified water proofing membrane with 100 mm over laps sealed and bounded to the surfaces by 'torchon' method.(iv) Applying two coats of bitiminous aluminium paint @ 200 Gram / Sq M (minimum) in two coats .Make incorporated : HYPERPLAS POLYSTER OF IWL (INDIA) LTD or equivalent in Pidilite industrries Ltd /STP Ltd all as specified and as manufacturer instruction complete. as per manufacturers instruction.

M&L Preparation of new or previously untreated steel and iron surfaces of any description, not otherwise description, over 10 cm width or girth apply two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

Cutting holes in brick walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

S&F tubular rolled sections as post, rafter, purlin, and its connected wk for shed structure and similar work complete using ERW or induction butt welded tubes conforming to I.S. 1161-1976 grade St.-240, complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in sun shade, roof covering/ cladding to wall, and similar work fixed with self tapping screws complete all as specified and directed.

Excavating over areas, not exceeding 1.50 m deep and getting out in any type of soil complete all as specified and directed.

M&L rolling and consolidating formation surface of road in cutting with 8-10 tonne power roller, including watering & filling in depressions which occur during rolling complete all as specified and directed.

M&L sand filling under floors or interlocking tile or in foundation or for cable protection in layers including punning, watering and consolidation complete all as specified and directed

M&L machine pressed precast concrete 80 mm thick glossy interlocking paver block M-40 Grade to IS 15658-2006, with grey cement and pigment laid over dry sand cushioning, filling of joints with sand,,complete all as specified and directed. Colour and shape approved by GE. Note : Sand cushioning shall be measured and paid separately.

S&F Reinforced concrete pipes 450 mm bore, class NP2 , laid and jointed complete with collars, including demolition and breaking up drain pipes, complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

M&L providing cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate as in lintels upto 1.50 metre clear span, cills, steps, seismic & other similar bands, plinth courses, parapets & railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs and the like including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

Point wiring with 1.5 Sqmm (nominal cross sectional area ), single core, PVC insulated with multistranded PVC unsheathed FR LSH copper conductor cable in and including rigid non- metallic PVC concealed conduit of suitable size medium grade ISI marked complete , including one continuity earth wire of PVC insulated, unsheathed 1.5 Sqmm (nominal cross sectional area ) FR LSH copper conductor connected to all fittings, common earth and connected to earth dolly including including modular metal flush box , cover plate and cover frame of suitable size for the One light / fan /bell controlled by one, one way switch 5/6 Amps, complete all as specified and directed.

Description same as per Item No. 48.00 but one 3 pin, 5/6 amps socket outlet point on independent board controlled by one, one way 5/6 amps switch complete all as specified and directed.

Description same as per Item No. 48.00 but one 3 pin, 5/6 amps socket outlet point on same board controlled by one, one way 5/6 amps switch complete all as specified and directed.

Point wiring with 2.5 Sqmm (nominal cross sectional area ), single core, PVC insulated with multistranded PVC unsheathed FR LSH copper conductor cable in and including rigid non- metallic PVC concealed conduit of suitable size medium grade ISI marked complete including one continuity earth wire of PVC insulated, unsheathed 1.5 Sqmm (nominal cross sectional area ) FR LSH copper conductor connected to all fittings, common earth and connected to earth dolly for one three pin 15/16 amps socket out-let point on an independent board including modular metal flush box , cover plate and cover frame of suitable size complete all as specified and directed.

S&F in of Ceiling rose three terminals surface bakelite type, AC, 50 HZ, 230V complete all as specified and directed.

S&F modular switch 1 way 6 A , 1 module ISI complete all as specified and directed.

S&F modular socket 6 Amps 2/3 pin combined 2 module ISI complete all as specified and directed.

S&F switch modular type 16 A, 1 module ISI complete all as specified and directed.

S&F socket modular type multipurposes 6/16 A, 2 module ISI complete all as specified and directed.

S&F surface /wall mounted LED batten (other than slim channel type) poly carbonate housing for retrofit LED tube T-8 type upto 1x22 watt, 4 feet long pre wired incl integrated electronic driver complete with all connected accessories all as specified and directed.

S&F ultra bright LED poly carbonate tube light 4 feet long 18 to 20 watts with THD less than 15% very high effficiency suited for T-8 tube light luminare with system efficiency 120 lumens per watts. High quality polycarbonate end cap in white finish and snap fitted to the housing complete all as specified and directed.

M&L for LED Bulk head fitings of wattage 6 to 13 watts designed for modern homes available with premium quality diffuser for glarefree light and easy to install snapfit installer complete all as specified and directed.

S&F LED bldg security light fitting 30 watts made up of pressure die cast aluminium housing with acylic cover as diffuser with IP-66, THD < 10% , lumen output ≥ 110 lumen per watt including GI mounting pipe light grade 40mm dia bend into size 1.2mtr in length including saddles and connected accesories including pvc wire from ceiling rose to connector of fitting complete all as specified and directed.

S&F MCB DB SPN 08 way double door with 200 Amps rated bus bar ,230 volts, 50 Hz complete all as specifed and directed.

S&F MCB SPN 32 Amps current rating 'C' series 10 KA breaking capacity complete all as specified and directed.

S&F MCB SP 6 to 32 Amps current rating 'C' series 10 KA breaking capacitycomplete all as specified and directed. Note:- Make of serial No. 61, 62 & 63 should be same.

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 2 core in trenches / under PCC/interlocking tiles incl making good of surface with PCC/ cementing incl connecting to existing LT panel board and VTPN DBs all as as directed at site, complete all as specified and directed.

M&L for Tubes, 'light grade,galvanised, with all fitting of size 40 mm ;laid in trenches or fixed in wll with saddles for cale protection/ mounting security lights incl bending and cutting to required length, complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep with service value 7.00 with brushless direct current motor (BLDC), complete all as specified and directed.

S&F Exhaust fan , steel body AC single phase 230 volt of size 300 mm mm sweep (heavy quality duly painted,complete with blade, frame and louvers all as specified and directed incl making/alteration of hole wherever necessary making good disturbed surface, painting to match with existing surfaces, complete all as specified and directed.

M&L Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level connect to galvanised earth lead wire of 4.0 sqmm size by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 40 mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150 mm c/c both ways etc complete all as shown in electrical plate No 5, connected to earthing test point complete including testing on completion all as specified.

Chitragupta Construction

M/s Narendra kumar Agrawal

M/S UnitedConstruction