ADDN ALTN OF COMPOUND WALL BEHIND BLDG AT CDU PBR AND PROVISION OF PAVER BLOCK AND FENCING AT GARDEN NEAR BLO OFFICE UNDER GE HADDO SRI VIJAYA PURAM

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation etc not exceeding 10 sqm on plan and n.exc 1.5 m in depth and getting out in any type of soil etc, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including CM bedding, removing rubbish off the premises etc, complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including similar pattern roof coverings etc, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided etc, complete all as specified and as directed.

Dismantling fencing wire mesh, any type and any thickness etc, complete all as specified and as directed.

Demolition of Precast cement concrete block walling built in CM or Cement lime Mortar etc, complete all as specified and as directed.

Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick above or below ground level etc, complete all as specified and as directed.

Demolition of Reinforced manhole , Drain over cover slabs in similar works etc, complete all as specified and as directed.

M&L Plain cement concrete (PCC) type D2 1:4:8 (using 40 mm graded aggregate) in foundation, filling and mass concrete etc, complete all as specified and as directed.

M&L for design mix renforced cement concrete M-30 ( Using 20 mm graded stone aggregate) as in foundation incl raft footing, foundation beams,plinth beams,bases for columns, cantilevers, bressummers etc, complete all as specified and as directed.

M&L for design mix renforced cement concrete M-30 ( Using 20 mm graded stone aggregate) as in Columns,pillars,piers,posts and struts etc, complete all as specified and as directed.

M&L for rough finished flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc, complete all as specified and as directed.

M&L for fair finished square, rectangular or polygonal formwork to sides of pillars, posts, struts, piers, columns and stanchions flat on plan etc, complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M&L for mild steel TMT bars 6 to 8 mm dia , cut to length, bent to shape required, including cranking, ties for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M&L Precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) etc, complete all as specified and as directed.

M&L for preparation on newly plastered external wall surface and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint complete all as specified and as directed. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard) etc, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm etc, complete all as specified and as directed.

M&L for Removing excavated material and debris exc. 250 m but n exc. 500 m and directed, etc, complete all as specified and as directed.

M&L cement concrete (1:2:4) type B-1 using 20mm graded aggregate as in lintle upto 1.5m clear span, steps, bed plates, kerb & coping including necessary formwork etc, complete all as specified and as directed.

M&L for 10mm thick plaster in CM (1:6) on fair faces of concrete/PCC block surfaces of walls finished even and fair (without using extra cement) etc, complete all as specified and as directed.

M&L for Cement concrete P.C.C (1:4:8) Type D2 (using 40 mm graded aggregate) as in sub base 100 mm thick etc, complete all as specified and as directed.

S&F for glossy finished chequered cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry including 15 mm thick screed bed of CM(1:6) in floors etc, complete all as specified and as directed.

M&L for pre cast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in manhole cover slab set in cm 1:6 etc including necessary formwork complete all as specified and as directed

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 etc, complete all as specified and as directed.

M&L for cement concrete1:2:4 Type B-1 Using 20mm graded stone aggregate as in surface channels or drain etc, complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exc 0.50 Cum, getting out hard/dense soil, returning filling in and ramming earth or Brocken rubble mixed with earth around, in layers not exceeding 25 cm etc, complete all as specified and as directed.

M&L for cement concrete Type B-1, 1:2:4 (using 20 mm graded stone aggregate) for post, struts (including caps) including weathering, slightly rounded or chamfered angles and throating and including necessary form work etc, complete all as specified and as directed.

Dismantling structural steel work etc, complete all as specified and as directed.

Supply & fabricate and fixing in position angle iron posts for fencing posts and struts including flat iron etc and including cutting tops to shape as directed , drilling holes, notching for wire etc flat iron fillets for securing fencing including all necessary welding , drilling, bolting or riveting, etc, complete all as specified and as directed. (Steel confirming to Fe-290 (Gde E-165)).

S&F for MS Galvanized with 1.0mm thick PVC coated chain link fencing 50mm x 50mm over 3.15mm GI wire etc, complete all as specified and as directed.

S & F for 10mm dia MS round bar for tighting/securing fencing wire etc,including two coats of synthetic enamel mpaint over a coat of red oxide primer after preparation of steel surfaces etc, complete all as specified and as directed.

M & L for Mild steel screw bolts (machine made) with hexagonal or square head one end and screwed the other, or screwed both ends each screw-wed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long diameter of neck in exc 16mm and n.exc 20 mm etc, complete all as specified and as directed.

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying 2 coats of synthetic enamel paint over one coat of red oxide primer etc, complete all as specified and as directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc, complete all as specified and as directed.

M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate as in 75mm thick as in sub base etc, complete all as specified and as directed by Engineer-in-Charge.

M&L for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/stopped ends etc complete all as specified and directed

Please Enable Macros to View BoQ information