STRENGTHENING OF DISTRICT HOSPITAL BISHNUPUR DISTRICT MANIPUR

Amount

DEMOLITION AND DISMANTLING

Demolishing Cement concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer in charge

Nominal concrete 1 or richer mix (i/c equivalent design mix)

EARTH WORKS

Banking excavated earth in layers not exceeding 20 cm. in depth, breaking clods,watering. rolling each layer with Y2 tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum B tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m. including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All Kinds of Soil

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sandy soil under floors including watering, ramming, consolidating & dressing complete.

CONCRETE WORKS:

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level:

1:4:8 (1 Cement:4 coarse sand:8 graded stone aggregate: 40 mm nominal size)

1:2:4 ( 1 Cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

1:5:10 (1 Cement: 5 coarse sand:10 graded stone aggregate: 40 mm nominal size)

Providing & laying damp-proof course 50 mm thick with cement concrete cement concrete 1 : 2 : 4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size)

R.C.C. Work

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level:

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

R.C.C. work in beams, suspended floors, roofs having slope uptp 15o landings, balconies, shelves, chajjas, lintels, band, plain window sills, staircases and spiral staircases above plinth level upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1 : 1 .5: 3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20 mm nominal size)

PRECAST

Providing, hoisting and fixing upto floor five lovol procast reinforced comont concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the tike including tho cost 01 required contoring, shuttering but excluding cost of reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand: 3graded stone aggregate 20mm nominal size).

STEEL WORK

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars

FORM WORK

Centering and shuttering including strutting,propping etc.and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Columns, pillars, posts and struts

Lintels, beams, plinth beams, girders, bressumers and sqm cantilevers

Suspended floors. roofs, landings, balconies and access platform, with water proof ply 12mm thick.

BRICK WORKS:

Brick work with 1st class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with 1st class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in

Cement mortar 1 : 4 (1 cement : 4coarse sand)

Honey-comb brick work 10/11.4 cm thick with 1st class common burnt clay FP.S. (non modular) bricks in superstructure above plinth level and upto floor V level in cement mortar 1 : 4 ( 1 cement : 4 coarse sand)

Stone work

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including levelling up with cement concrete 1 :6:12 (1 cement: 6 coarse sand . 12 graded stone aggregate 20mm nominal size) at window sills, ceiling level and the like.

WOOD WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames.wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately

Local best quality Uningthou wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.

Local best quality Tolhao Wood

35 mm thick Shutters

Providing and Fixing paneling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling tor panelled or panelled and glazed shutters 25 mm to 40 mm thick

Local best quality Tolhao wood

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing bright finished brass door latch with necessary screws etc. complete

Providing & fixing bright finished brass Tower bolts (barrel type) with necessary screws etc. complete.

Providing and fixing chromium plated brass handles with necessary screws etc. complete:

STEEL WORKS

Steel work in built up tubular (round, square or rectangular tubes etc.) trusses etc., including cutting. hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc. complete.

Electric Resistant or induction butt welded tubes

FLOORING:

Brick on edge flooring with bricks of 1st Class on a bed of 12 mm cement Mortar including Filling of the joints with the same mortar with common burnt clay non modular bricks

1:4(1Cement:4 Coarse Sand)

Cement concrete flooring 1:2:4 (I cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost Of nosing of steps etc. complete.

40mm thick with 20mm nominal size stone aggregate.

Cement plaster skirting (upto 30 cm height) with cement mortar 1:3 (I cement : 3coarse sand) finished with a floating coat of neat cement

18 mm thick

Tile work in skirting, risers of steps and dado (upto 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.

Marble tiles (polished) Raj Nagar

18mm thick

Marble stone flooring with 18mm thick marble stone (sample Of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with

Raj Nagar Plain

Extra for prefinished nosing to treads of steps of marble stone.

25mm wooden planking, tongued and grooved in flooring including fixing with iron screws complete with

1st class teak wood

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in alt colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (I cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% nad conforming to IS:15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.

Size of tile 600x600 mm (Single Charged)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.080/0 and conforming to 19.15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will bo done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Double charge vitrified tile polish of size

size of tile 600 x 600 mm

ROOFING

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections, power pressed from M.S. sheet and galvanised with zinc coating of 120 gms/ sqm (both sided inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts,other flange of cleat fixed to the angle hangers of 25x25xO.55mm of required length with nuts and bolts of required size and the other end of the angle hanger fixed with intermediate G.l. channels 45x15xO.9mm running at the spacing of 1200mm centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to Gil. intermediate channel with connecting clips made out of 2.64mm diax230mm long C.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/pattition with the help of rawl plugs at 450mm centre, with 25mm long drive-all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishng to a flush finish of tapered and square edges of the board with recommended jointing compound,jointing tapes, finishing with jointing compund in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board,all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed. all complete as per drawings, and specification and direction of the Engineer in Charge but excluding the cost of painting with

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineerin-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using selt drilling Iself tapping screws ot size (5.5x 55 mm) with EPDM seal,comptete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with

Precoated galvanised iron profile sheets 0.40 mm thick

Providing and fixing precoated galvanised steel sheet roofing accessories , Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and

Ridges plain (500 - 600mm).

Precoated galvanised iron profile sheets 0.50 mm

Gutter (600 mm over all girth),

Precoated galvanised iron profile sheets 0.50 mm

FINISHING:

12 mm cement plaster of mix 1:4 (1 cement:4 coarse sand).

(1 cement:4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix 1:4 (1 cement:4 coarse sand).

1:4 (1 cement:4 coarse sand).

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

New work(two or more coats)over and including priming coat with cement primer

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface

Water thinnable cement primer

Finishing walls with textured exterior paint of required shade:

New Work(two or more coats applied @3.28 ltr/10 Sqm)over and including base coat of water proofing cement paint [email protected]/10 sqm.

Applying priming coat:-

With ready mix pink or grey primer of approved brand and manufacture on wood work(hard and soft wood)

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works:-

Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture to give an even shade.

Two or more coats on new work

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth

SANITARY INSTALLATION

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap. 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handlo lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580 x 440 each as. 5,421.50 mm with integral type foot rests

Providing and fixing white vitreous china flat back or wall corner type lipped Iront urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with utomatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete. including painting of fittings and brackets, cutting and making good the walls and floors wherever required

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing P.V.C. tor sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

Providing and fixing 600x450 mm bovolod cdgo mirror of superior 1,053.30 glass (Of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass scrows and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 each 195.80 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT urinal cock of approved quality and colour.

15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms.

Providing and fixing UPVC soil, waste, rain water and vent pipes including all requisite fittings, jointing of pipes & fitting with solvent cement, tenching, refilling & testing of joints complete as per direction of Engineer in charge

75 mm dia

110 mm dia

Water Supply

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work. including cutting chases and making good the wall etc.

20 mm diameter

25 mm diameter

Providing and fixing G.l. pipes complete with G.l. fittings including trenching and refilling etc. External work

32 mm diameter

Providing and fixing C.P. brass bib cock of approved quality conforming tQ IS:8931

15 mm diameter

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make confcrming to 19.8931.

15 mm diameter

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

25 mm diameter

Providing and fixing gun metal non-return valve of approved quality (screwed end)

32 mm diameter

horizontal

Providing and placing on tcrrace (at all floor levels) polyethylene per litre 10.20 water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and tho baso support for tank.

Manhole cover for septic tank

Providing and fixing aluminium work for doors, windows, ventilators and partitionswith extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/ Neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleatangle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steelscrews, all complete as per architectural drawings and the directions Of Engineer-incharge. (Glazing and panelling to be paid for separately):

For fixed portion.

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness

INTERNAL ELECTRIFICATION INSTALLATION

SUB HEAD-1: COPPER WIRING IN STEEL CONDUIT

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group A

Group B

Group C

Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and Drawing (following pair) 0.5 sqmm FR PVC insulated copper conductor unarmoured telephone cable in the existing surface/recessed steel/PVC conduit as reqd.

Supplying and Drawing Co-Axial TV Cable RG-6 grade 0.7mm Solid copper conductor PE insulated shielded with file tinned copper braid and protected in PVC sheath in existing surface / recessed steel/ PVC conduit as reqd

Supplying and Drawing following size of steel conduit along with accessories in surface/recess i/c painting in case of surface conduit or cutting the wall and making good the same in case of recessed conduit as reqd.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telepone socket outlet

TV antena socket outlet

S/F 25 amp Air-Conditioner power plug point i/c 4 modules metal box on surface or in recess 4- modules plate and cover in front 25 amp modular starter 25 amp modular socket outlet and 25 amp plug i/c connection etc as reqd.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply and fixing modular type blanking plate on existing modular plate and switch ox excluding modular plate as reqd.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required..

1 or 2 Module (75 mmX75 mm)

4 Module (125mm X 75mm)

12 Module (200 mmX150 mm)

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/wooden block includingonnectiontc as reqd.

SUB HEAD-II : MCCB, MCB & DB’S

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders inexisting cubicle panel board including drilling holes in cubicle panel making connections etc as reqd.

800 A , 35 KA, 4 Pole MCCB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way, Double door

12 way double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required

Single pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying, installing, testing and commissioning of surfaceecess mounting vertical type 415V MB distribution board of sheet steel dust protected duly phosphatized and powder painted inclusive of 2 amps tinned copper busbar common neutral link earth bar din bar forunting MCB's detachable gland/knock out plate and with 100 amps 10A MCCB as incomer interconnection between incomer MCCB and bus of followingay (butthout MCB's) as reqd.

12 Way (8+36) TPN MCB DB Duble door.

Earthing with copper plate 600mm x 600mm x 6mm thick i/c accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) as reqd

Extra for using salt and charcoal for G.I or copper plate earth electrode as reqd

SUB HEAD IV:- Fittings/Fixtures

S/F 48'' sweep (1200mm) A.C.Ceiling fan complete with down rod canopy 3 (three) blades but without regulator etc as reqd.(Make Bajaj/Usha or similar)

S/F 450mm dia wall mounting fan complete wit all accessories etc as reqd.

Supplying, Erection, testing and commissioning of (pre-wired) wall bracket/ceiling fittings of all sizes and shapes containing CFL/LED/W GLS lamps per fitting, complete with all accessories including connection etc. as required (havell,s /Bajaja/Phillips/Cromton).

Ceiling fitting (Surface) with 15/18 watt LED Lamp.

Supplying , Installation, testing and commissioning of LED Lamp (havell,s /Bajaja/Phillips/Cromton). Including connection etc. as required.

With CFL 12/15 Watts Lamp.

Supplying, installtion of exhaust fan in the existing opening, including making good the damage, connection,testing,commissioning etc as reqd.

225mm sweep

S/F surface Pendent mounting 9 W led bulb complete with driver i/c connections etc as reqd

Supplying V Cable at site as per specification of engineer in charge.

16 mm (Two core) MV Cable

Supply and installation of Control Panel 200 amp

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

100 A, 10 kA,TPMCCB

Providing anf Fixing ( Following rating and breaking capacity) MCCB in esisting cubicle panel board including drilling holes in cubicle panel & making connection as reqd.

125 A, Isc = 25 kA for 1 second

Providing and fixing 125 amp TPN stand ground on load change over switch (Compact design)415/500 V including connectionetc as reqd

S/F Bus bar chamber with 4 strips copper bus bar of length 300mm suitable for 200 amp capacity complete with all accessories i/c connection earthing the body etc as reqd

Earthing with copper earth plate 600 mm X 600 mm X 6mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. without charcoal/ coke and salt) as required.

Extra for using salt and charcoal for GI or copper plate earth electrode as reqd

Providing and Fixing 4mm dia copper wire on surface or in recessed for loop earthing as reqd

CHAPTER 7-MV CABLE LAYING

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

16 Sq.mm flat twin PVC sheathed/weather proof

M/S Acura Ventures (BID ID -10041)

M/S KIM & SONS CONSTRUCTIONS & EQUIPMENTS (BID ID -10044)

Bidder Name

PAMESHOR ENTERPRISES