SPECIAL REPAIR / REPLACEMENT OF STP AT BI LINE 350 KLD ALLIED WORKS ELECTRIC WIRING OF BLDG NO. BI14 BI15 OF 641 SATA BTY AND PROVN OF 8 X AC 1.5 TON CAPACITY WITH STABILIZER AT NEW CANTT PRAYAGRAJ

Amount

Excavating in post holes (or similar holes) in soft/loose soil each not exceeding 0.5cum, getting out, returning, ,watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified & directed.

M&L for cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed .

Dismantling fencing wire mess any type any description complete all as specified and directed at site.

Dismantling RCC Post any section, including taking out embedded portion and making good disturbed ground; posts embedded in natural ground complete all as specified .

Mild steel work conforming to Fe-290 (Gde E-165) in posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified & directed.

Supply only chain link mild steel galvanized fencing, any type or size complete.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete.

S & F in repair Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as directed and specified.(each line wire to be measured)

Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide primer complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed trusses complete all as specified and directed.

S&F of framed work as in doors or gates of angle or other section with gusset plates,rails,braces etc complete, drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with hinges or steel hanging door fittings or other covering running rails and guide and hanging also fastening and fixing complete all as specified and directed

De-silting / cleaning of drain bed from grass / loose earth / roots etc complete all as specified and directed

Demolition of brick wok built in cement mortar including all quoins,arches,pillars,etc, but excluding ashlar facing, dressed stone work, precast concrete article complete all as specified

M&L for brick work with fly ash bricks ,straight or curve on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed

All as per Srl item No. 14 but except bricks complete all as specified and directed. Note:- Old bricks obtained from demolition shall be used.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth, for foundation etc or for shaft, wells, cesspits, manhole, pier holes etc not exceeding 10 sqm on plan and getting out in soft /loose soil complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C2 using 40 mm graded crushed stone aggregate as in foundation of wall / drain or channel complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 using 20 mm graded aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings, kneelers, apex stones, bed plate, kerbs and likes slightly rounded or chamfered complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

Add to or deduct from item No. 20 for each 25 mm girth or part thereof over or under 30 cm girth etc complete all as specified & directed.

Removing excavated materials exceeding 500 m and not exceeding 1.5 Km & depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified & directed.

S&F 75 mm bore low density polyethylene (LDPE) pipes of pressure rating 6 kgf/ Sqcm white in colour laid in trenches including all fittings such as bend, elbow, tee etc complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed .

M&L for 80mm thick M-40 grade factory made rubber moulded vibratory cement concrete coloured interlocking paver block any shape and size conforming to IS 15658-2006 with grey cement and pigment as approved laid over and including 25mm thick sand cushion and joints filled with sand complete all as specified and directed

M&L for Preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of cement wash complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coat of white wash on wall complete all specified and as directed.

M&L complete removal of the old treated surfaces of wall including cornices etc. by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and removal of vegetation and applying two coat of Cement Base Paint white or tinted of approved shade complete all as specified and directed.

M&L for preparation of old plastered or unplastered surface of wall including cornices etc. by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and removal of vegetation and applying two coat of white wash on old surface of wall complete all as specified and directed.

M&L for preparation of old painted surface of steel by brooming down or steel wire brushing, scrapping down smoke soot, moulds and efflorescent salt and trading oil and greasy spots of any description , not otherwise described over 10cm in width or girth and applying one coat of synthetic enamel paint, white or tinted complete all as specified and directed

M&L for preparing old plastered decorated surfaces of wall and applying one coat of exterior weather proof 100% anti-fungal acrylic smooth emulsion with silicon additives that offer anti algae high performance exterior wall finish by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper, should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. Note: Scraping of old decorated surface to be done by mechanical sander with 1500-2700 rpm, with internal dust extraction system for clean environment, certified by paint manufacturer

Desludging of existing equalizer tank tubesuttler tank , chlorine contact tank, filter feed tank , storage tank MBBR tank of sewage treatment plant 350 KLD capacity and getting out sludge and depositing to a distance exceeding 1.5 km but n. exceeding 2.00 Km outside MD land at isolated place complete all as specified & directed .Note- (i) Pumping out sludge water from equaliser tank by using Diesel engine operated pump and necessary diesel is to be arranged by contractor during cleaning of tank. Rate quoted by contractor are deemed to be included this aspect.

Cleaning of sludge drying beds of size 4.4 x 4.4 m and depth 0.80M by removing sludge/vegetation from disposing sludge bed at abandoned place from cantt area completed all as specified & directed.

Dismantling existing grid separator manual type & supply , installing, testing & commissioning manual type grid separator system as per existing one duly grouted made of MS duly epoxy coated for size of chamber 3.0 x 0.5 x 1.5 m height including making good disturbed RCC/PCC surface complete all as specified and directed

Dismantling existing Bar Screen manual type & Supply , installing, testing & commissioning bar screen manual type made of 304 stainless steel bars with 6 mm clear opening , frame made of MS flat epoxy coated 25x3 mm including all connected accessories duly grouted for size of clamber 1.2 x 0.5 x 1.0 m height including make good distrubed RCC/PCC surface complete all as specified and directed.

Taking out old unserviceable MBBR media from reactor 1 & 2 and cleaning the MBBR tanks & dewatering complete all as specified and directed.

M&L for filter media of MBBR tank complete all as specified & directed. Make - Weldon or as approved by Engineer in charge.

Taking out air compressor including electric motor 7.5 KW, 3 Phase 415 V installed at STP disconnecting electric connection and dismantling motor, cutting burnt winding and cleaning slots with non greasy chemical and rewinding with super enameled copper wire of existing gauge incl. insulating material, varnishing complete and repair of compressor of capacity 260 Cum/Hr, 1400 RPM by dismantling, grinding, polishing of cylinders, pistons, replacement of parts such as piston rings, bearings including replacement of compressor oil 5 Ltr to make the compressor in good running condition, refixing the same after repair testing & commissioning for satisfactory operation complete all as specified & directed by Engineer- in- charge

Taking out/Dismantling the unserviceable part of sewage treatment compressor blower and replace with new one complete compressor unit including testing after completion all as specified and directed by Engr-in-Charge

S&F in replacement suction filter suitable for sewage treatment compressor blower complete all as specified and directed.

S&F in replacement gears with Hub complete with harware suitable for sewage treatment compressor blower complete all as specified and directed. Make : Everest or equivalent as per ISI Marked complete all as specified and directed.

Material & Labour for replacement of Sand Filter vessel, replacement of face piping of size 80 mm dia heavy duty ISI Marked MS pipe including replacement of valves replacement of gaskets, replacement of pressure gauges and fixing the same as per existing one, painting of pipes with two coats of Black Paint over a coat of red oxide primer, making of flow direction on the pipes including painting of filter vessel of size 1200mm dia x 1500mm height with two coats of aluminium paint over a coat of red oxide primer & testing the system for satisfactory operation complete all as specified and directed.

Disconnecting existing defective electric motor of any make 5 to 10 HP from electric mains by isolating the naked connections, removing from foundation by unscrewing the nuts, bolts etc, dis-couple from pump etc opening of motor for inspection in presence of Engr-in-Charge & carry out minor repairs at site re-assembling the motor after repair, refixing in position re-connecting same as prior to removing from foundation including replacement of nuts, bolts washers if necessitates of suitable size, testing and commissioning complete all as specified and directed. NOTE : (a) Replacement of defective parts shall be measured and paid separately as S&F here after. (b) In case of major repairs not possible at site, the motor shall be shifted to contractor’s workshop and cost of shifting to work shop and back to site included in the quoted rates.

Taking out old unserviceable/burnt copper winding of motors capacity 5 to 10HP and M&L for rewinding of electric motor of capacity 10 to 15HP , 3 Phase with super enameled copper winding wire of suitable gauge as per existing including cleaning of rotor slots, all winding/insulation material, varnishing etc. complete and testing at site on full load after reinstallation to the full satisfaction of Engr-in-Charge complete all as specified and directed.

M&L for replacement of Ball bearing of the electric motor upto 10 HP 3 phase / single phase complete all as specified and directed.

M&L for replacement of MS Shaft of the electric motor upto 10 HP 440 Volts in repairs complete all as specified and directed.

Taking out defective pump set of any type, any make (including Sewage Pumps or filter pump installed at STP) of capacity upto 15 HP by unscrewing the foundation bolts, disconnecting from water connection, and disconnecting from electric motor, opening for inspection in presence of Engr-in-Charge and carry out minor repair at site, in case major repair/replacement of parts not possible at site, the pump shall be shifted to contractor's workshop on his own cost, and re-fixing, re-connecting in position, testing and commissioning complete including replacement of required parts, nuts bolts washers as specified and as directed. NOTE : (i) Replacement of defective part by new one shall be measured and paid separately under respective items.

Supply only in replacement mild steel shaft upto 10 HP centrifugal pump set of any make complete all as specified and directed.

Supply only in replacement Gland packing, CI Check Nut, Gland Cover with Nut and Bolts complete all as specified and directed.

Supply only in replacement ball bearing including greasing etc complete all as specified and directed.

Supply only in replacement impeller broze/brass complete all as specified and directed.

Supply only in replacement neck ring complete all as specified and directed.

Supply, fixing, testing and commissioning in replacement of decrin dosing pump model No 96NGQ 51 high pressure single head gear motored adjustable dosing pump with accessories including lead tubing, connecting nuts injection check valve , clay weight and ferrules with altoch dosing system model ADS -1 consisting of 40 ltr -100 ltr PE/FRP tank with PE/FRP lid and level gauges along with agitator with shaft and blade in plastic , mounted on tank complete all as specified and directed. Make : AQUAFIT/CHLOROTECH/SEEPL

Supply, Installation, testing and commissioning of non clog submersible pump set with supper enamelled copper winding set capacity 10 HP ,3 phase 415 Volts complete all as specified and directed. Make KSB / Crompton / Kirlosker

S&F column pipe heavy grade 'C' 80 mm dia bore both end flanged including jointing material such as nuts bolts washers etc including clamp of suitable size of pipe to hold the column pipe on the top surface of sewage water collection tank complete all as specified and directed.

Supply only compressor oil complete all as specified and directed.

Dismantling and taking out defective unserviceable butterfly valve and replacement with new butterfly valve 100 mm bore including jointing with MS nuts, bolts packing, minor adjustment complete all as specified and directed. Make - Kirloskar/ Leader/Zoloto

Dismantling and taking out defective unserviceable butterfly valve and replacement with new CI body with SS gate butterfly valve 80 mm bore including jointing with MS nuts, bolts packing, minor adjustment complete all as specified and directed. Make - Kirloskar/ Leader/Zoloto

Dismantling and taking out defective unserviceable butterfly valve and replacement with new CI body with SS gate butterfly valve 40 mm bore including jointing with MS nuts, bolts packing, minor adjustment complete all as specified and directed. Make - Kirloskar/ Leader/Zoloto

Taking down old U/S sewage flow meter and supply and fixing electronic type sewage flow meter 100 mm dia , with electronic display, operating voltage 230 volt, 50 Hz including cabling and electrical connection from panel to flow meter of same capacity and size complete all as specified and directed.

Dismantling of existing Air Rota meter & Supply , fixing testing & commissioning of new air Rota meter of capacity 300 cum/hr as per existing one complete all as specified and directed.

Supply and replacement of pressure gauge (water) range -0-20 Kg/cm² complete all as directed.

S&F in replacement V- Belt suitable for compressor blower complete all as specified and directed. Make : Everest or equivalent as per ISI Marked

S & F in replacement of PVC flexible hose pipe upto 100 mm dia for connecting with sewage /suction pump including required fixing arrangement complete all as specified and directed.

S&F MS Black pipe of wall thickness 7 mm confirming to IS : 1239 Part -I including welding of flange as per site requirement including jointing materials such as nuts, bolts, washers etc of 100 mm dia bore complete all as specified and directed.

S&F MS Black pipe of wall thickness 7 mm confirming to IS : 1239 Part -I including welding of flange as per site requirement including jointing materials such as nuts, bolts, washers etc of 80 mm dia bore complete all as specified and directed.

S&F MS Black pipe of wall thickness 7 mm confirming to IS : 1239 Part -I including welding of flange as per site requirement including jointing materials such as nuts, bolts, washers etc of 50 mm dia bore complete all as specified and directed.

S&F MS Black pipe of wall thickness 7 mm confirming to IS : 1239 Part -I including welding of flange as per site requirement including jointing materials such as nuts, bolts, washers etc of 40 mm dia bore complete all as specified and directed.

S&F MS sump cover /duct cover of 5 mm thick of required size complete including MS angle Iron frame of required size complete all as specified and directed by Engr-in-Charge.

S&F 100mm bore sluice valve, heavy duty both ends flanged class PN-I with high tensile steel spindle cast iron head operated wheel and cap top, nuts and bolts, washers including 3mm thick rubber gasket joint including taking down old unserviceable valve complete all as specified and directed.

Taking down old unserviceable venturimeter and S&F of venturimeter of size 100 mm bore flanged end drilled type and jointing materials complete all as specified and marked complete all as specified and directed by Engr-in-Charge.

Supply, laying & testing of cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 core complete all as spd and directed.

M&L for 16 sqmm 3 core submersible copper conductor flat cable suitable for mono block,non clog submersible pumps all as specified and directed by Engr -in-charge.

M&L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried directly in ground (earth) pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connected to galvanised earth lead wire 4mm dia as earthing lead by means of bolts, nuts, check-nuts and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe light grade 40mm bore for protection of GI strip from earth electrode to and including the earth test point of galvanised Iron/steel of size 75mm x 75mm x 25mm, supplying and laying charcoal stone aggregate) chamber and mild steel angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B-1 using 20mm graded crushed stone aggregate reinforced with 8mm dia TMT BARS @ 75mm O/O both ways with mild steel handle 12mm dia, PGI funnel with wire mesh, 20 MM dia GI pipe light grade for watering all as shown in electrical plate No.3 of MES SSR Part - 1

Dismantling old broken / damaged valve pit chamber of size 1050mm x 1050mm x 1050mm (internal dimension) complete including excavation and earth work, PCC 1:4:8, type D-2 using 40mm graded stone aggregate, brick work in cement mortar 1:6, plastering in cement mortar 1:4 (internally) and including 3mm thick mild steel sheet cover and painting with two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for two coat of synthetic black/red/green enamel paint including scraping down complete with old painted surface of pipe line, equalizer tank, tubesuttler tank ,chlorine contact tank, filter feed tank , MBBR tank of sewage treatment plant upto 12 mtr height from ground level and rubbing pipe with 10 No sand paper to make surface smooth including arrow marking and writing of direction of water complete all specified and directed

Stopping the sewage line by divering from entry point and keep aside during maintenance or connection to nearest SPH,CLEANING UP ALL chambers , washing, cleaning of incommer .outdoing holes, cleaning of Motor housing structure, all as specified and directed

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead strip 32×6mm as earthing lead connected to GI earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth strip connected to DG Body & Neutral and LT Panel/Feedar pillar and protected by galvanised iron pipe medium grade 40 mm bore and 20mm bore medium grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:3:6 type C-2 & RCC cover in 1:2:4 and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009. complete and providing Earth pit marker.

S & F in replacement of CI Impeller for the submersible motor / centrifugal pumping set of capacity upto 15 HP complete all as specified and directed.

Taking down carefully sub main wiring of any type complete with MCB DBs MCB, isolators wooden batten, surface conduit/casing conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing capping/conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade conduit with all fixing accessories of 20mm dia, using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed surfaces complete all as specified and directed for the following :- Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface.

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amp same board.

One point for socket outlet 5 amps on independent board

All as per srl item No. 69 above but for one 3 pin socket outlet 15 amps, independent, with cables 2.5 sqmm size on independent board 2.5 Sqmm earth wire complete all as specified and directed.

All as per srl item No. 69 above but for one 3 pin socket outlet 15 amps, independent, with cables 4.0 sqmm size on independent board 4.0 Sqmm earth wire complete all as specified and directed.

S&F ceiling rose surface type bakelite 65x50mm three terminal complete all as specified and directed.

S&F switch piano flush type single pole one way 6 amps 230 Volt complete all as specified & directed.

S & F in repair pendant type lamp holder, PVC/Polycarbonate type with cord grip cap complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin, 6 Amps flush type complete all as specified & directed.

S&F Socket out let 2 in one, 5/3 pin 5 & 16 Amp complete all as specified & directed

S&F switch piano flush type single pole one way 16 amps complete all as specified & directed.

S&F fan regulator, 5 stepped, 120 W, single phase 230 volt including connection complete all as specified & directed.

M&L for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 4 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 4 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M&L for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 6 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 6 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

S&F sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with 200 amps rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F MCB single pole & neutral 40 to 63 amp, 240 volts, 'B' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'B' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S & F in replacement LED light fitting with box type ultra slim linear LED lighting fixture with co- extruded polycarbonate body environmental friendly, energy efficient tube light complete with all accessories internally pre- wired and including LED lamp 20 watt 01 No and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S & F in replacement LED light fitting 10 watt mirror type with high output with opal diffuser 2 ft 230 V AC with driver holder and LED lamp including making connection with three core PVC flexible insulated, sheathed copper conductor cable complete all as specified and directed.

Supply & fixing ceiling fans complete with blades ,down rods , electronic regulator and accessories ,230V ,1200mm sweep .min air delivery 210 CFM with service valve 6.00 BEE .five star rated with brushless direct current ( BLDC) including required length and size of copper stranded conductor for connection from ceiling rose to connector of fan including testing on completion complete all as specified and directed.

S&F mild steel medium grade 15 mm dia pipe down rod of require length with making split holes, cut etc at both ends of pipe as required for hanging ceiling fan including painting of rod with synthetic enamel white paint along with U shape shackle clamp assembly made out of MS flat iron including check out, bolts, screw, washer, split pin lock nut , rubber reel complete all as specified & directed.

S&F in replacement of VTPN DB 4 way, 160 A MCCB Double door DB's As per IEC 61439-3, Suitable for Flush Mounting and Surface Mounting, With 250 A Copper Busbar for each phase, With 2 Neutral bar, 2 Earth bar and Cable ties for Cable management, Fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP 43 & IP 54 dB's, with provision for MCCB as incomer complete all as specified and as directed.

S & F MCCB 100 Amps, 415 Volts, 4 Pole, breaking capacity 16 KA, ISI marked, fix type complete all as specified & directed.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection bracket for street light made out of 40 mm bore GI pipe medium grade not less than 1.2 mtr length bent at 120 degree to shape fixed on pole/wall with and including 50x6mm FI clamps = 02 Nos with nut bolts, washers including painting of clamps with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F vertical /horizontal water heater storage type, electrically operated of capacity 25 litres, BEE 5 star rated steel body and inner tank made with stainless steel duly thermal insulated with 2 KW heating element complete with and including vent pipe , fusible plug, safety valve, earth connector, PVC connections(hot and cold) and electric connection all as specified and directed.

S & F of steel water tubing, medium grade, ISI marked galvanised, 15 mm bore with all fittings such as bend, elbow, socket, tee, reducers, union etc, fixed to walls and ceiling or laid in floors complete all as specified and directed

S&F stop valve or cock concealed type fancy type of 15mm bore screwed down for high pressure with crutch or butter fly handle ,long shank screwed both end for iron pipes including cover plate complete all as specified and directed.

S&F sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug and socket along with one MCB, single pole of current rating 20 amps, B series 240 volts AC fixed to the wall surface or making suitable size of hole in the wall to fix it whenever is required and making good the existing surface complete all as specified & directed.

S&F 15 mm bore Bib taps, cast copper alloy, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed.

S&F in repair PVC connection 15mm dia and 45 cm long with 2 Nos PTMT nuts, complete all as specified.

S&F Exhaust fan 300 mm sweep Metallic body Range complete and shutters including required length and size of copper stranded conductor for connection from ceiling rose to connector of fan with provn of making hole in wall complete with grouting of nuts, bolts and washers and all other accessories required for fixing of fan including testing complete all as specified and directed.

Supply, installation, commissioning and testing of 5 star rated split air condition of capacity 1.5 TR (4500 Kcal/Hr) complete with cordless remote control unit and air ionizer and plasma filter for better air quality. Indoor unit shall be Hi wall mounted type suitable for 230 volts, 50 Hz, single phase AC supply and capable of performing the function as cooling, air circulating and filtering. The air condition shall be complete with automatic temperature control ( by comprising of variable speed / variable tonnage depending upon heat load inside the room) with electronic thermostat complete as per IS 11338 of 1985. Outdoor unit of the AC shall be fitted with discharge cooled type rotary / scroll compressors operating on non CFC refrigerant with suitably rated capacitors start electric motor equipped with overload protection and duly mounted on resilient mounting for quite operation. The casing of indoor unit shall be made of ABS/HIPS/GS. The control box of the indoor unit shall with stand flame retardant test to grade V/O as per UL 94. The filter packs provided shall be washable. Remote cordless control with LCD/LED display shall be provided on indoor unit and on handset. Overall powder factor of the unit shall not be less than 0.85 at operating conditions. The inverter type AC shall correlate to the values as specified by the OEM and latest IS/BIS certification as mentioned in the table 2.2 of the Gazette of India notification No. 024 (E) dated 5 Jan 2010 issued by central Government of India. Note:- Quoted rate shall be deemed to include the cost of 2.5 Sqmm 4 core multi stranded copper cable and copper tube of 3 mtr length, bracket, hole in brick wall etc for fixing & connection) (ii) Additional length beyond 3 mtr shall be measured & paid separately. (iii) Warranty on compressor should be 5 years minimum and warranty of machine should be one year minimum.

S & F Voltage stabilizer for automatic operation single phase naturally air cooled indoor type and designed for input variation between 170v to 250v with out put voltage stabilizer at 230v with accuracy of + 2.5% and of capacity 5 KVA complete all as specified & directed.

Supply & laying of copper tubing of dia 1/2 inch dia including insulation with heavy duty rubber foam & brazing work complete all as specified and directed.

Supply & laying of copper tubing of dia 1/4 inch dia including insulation with heavy duty rubber foam & brazing work complete all as specified and directed.

S&F PVC insulated flexible wire four core 2.5 sqmm copper conductor 1100 volt grade heavy duty complete all as specified and directed. .

S&F low density polythene pipe (LDPE) of pressure rating 6 kg/sq cm drain pipe of size 40 mm bore from indoor unit to exist point as per design including accessories clamp fasteners complete all as specified and directed.

Schedule of Credit (MINUS) Rs. 104082.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. ] This amount shall be automatically deducted to arrive at tendered sum

New Era Engineers (BID ID -3157317)