SPECIAL REPAIRS OF BLDG NO P-506 AND SPECIAL REPAIRS TO BLDG NO P-46 AMPHIBION SAINIK INSTITUTE IN BRICHGUNJ MILITARY STATION, PORT BLAIR

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate dismantling) complete all as specified and directed.

Demolition of Precast Concrete Block work built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, approns and laid bedded and pointed in any mortar etc.

Dismantling Plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings in roof covering all as specified.

Dismantling wrought iron or mild steel of any description not otherwise provided for complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down and refixing in same or other opening chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each complete all as specified and directed.

Excavation over areas, not exceeding 1.5m deep and getting out in hard dense soil complete all as specified and directed.

M & L for cement concrete 1:4:8 type D2 ( using 40 mm graded stone aggregate) as in foundation, filling mass concrete complete all as specified and as directed.

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-30 in columns, pillars, posts & struts complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-30 in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed..

M&L for Reinforced cement concrete design mix M-30 in slabs supported on walls, beams & columns complete all as specified and directed..

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 5 to 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

S&F Steel work in tubular/structural trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

S&F mild steel plates (plain or chequered) conforming to Fe 410-W (Gde E-250) quality –A, channels, squared cut or notched (ordinary or countersunk), forming holes, without any attachments welded to frame/truss complete all as specified and directed.

S&F Rolled mild steel flat as wind ties conforming to Fe 410-W (Gde E-250) quality -A including securing bolts and all necessary drilling, bolting complete all as specified and directed.

M&L Painting to new steel and iron surfaces of exc. 10cm wide or girth by two coats of synthetic enamel paints over a coat of red oxide primer including preparation complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed.

M&L Precast Cement Concrete Block Masonry with Solid Block, exc 10cm in width in type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) complete all as specified and directed.

M&L 40mm thick Damp proof course incement concrete 1:2:4 type B-o to horizontal or vertical surface including necessary formwork complete all as specified and directed.

Taking down cement plaster of any description on brick or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1: 6 on other fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 5mm thick in CM 1:3 on soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like finished even and smooth without using extra cement.

M&L for rendering 15mm thick in two coats on faces of brick work or concrete surfaces; first coat (rendering coat) of 10 mm thick in cement mortar 1: 6 and second coat (finishing coat) of 5 mm thick in cement mortar 1: 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished even and smooth complete all as specified and directed.

Supply only integral WPC .

M & L for preparing newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of putty complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of putty complete all as specified and as directed.

M & L for preparing old plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of putty complete all as specified and as directed.

M & L for preparation of old plastered wall surfaces and applying two coats of oil bound distemper over a coat of resistant primer over a coat of putty complete all as specified and as directed.

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed.(Make Apex Ultima)

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : Old Surface (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc and preparation of old surface complete all as specified and as directed. (Make Apex Ultima)

M&L Non skid joint free ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.18 Sqm but n.exc 0.38 Sqm, in neat cement slurry and pointed in white or coloured cement with pigment to match over 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

All as per item No. 44 except screed bed but in skirting/dado laid over 10mm thick cement plaster in cement mortar 1:4 complete all as specified and as directed.

M&L Glazed ceramic coloured / printed tiles (450X350mm) x6-7mm thick on vertical surfaces as in skirting/dado, set and jointed with neat cement slurry and pointed in white/coloured cement to match the shade of tiles over 10mm thick rendering in cement mortar 1:3 complete all as specified and as directed.

M&L Light shade Vitrified ceramic tiles 10mm thick (Square/rectangular) area of each tile exc 0.42 Sqm but n exc 1.00 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

All as per item No. 47 except screed bed but in skirting/dado laid over 10mm thick cement plaster in cement mortar 1:4 complete all as specified and as directed.

M&L for Heavy duty Vitrified tiles of size 300x300x8 to10mm thick or high dimension (except thickness) of any colour any design durastone weather proof impacr resistant abrasion resistant exterior tiles as in floors etc set and jointed in neat cement slurry over and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15 Cm deep and getting out in any type of soil complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 75mm thk cement concrete type D2 1:4:8(Using 40mm graded stone aggregate) in sub base of flooring/hard standing complete all as specified and directed.

M&L 40mm thk cement concrete type B-1 1:2:4(Using 20mm graded stone aggregate) in sub base of flooring/hard standing complete all as specified and directed.

M & L for coloured chequered cement concrete tiles 30 cm x 30cm x 25 mm thick, set and jointed neat cement slurry and pointed with With mixture of white & grey cement in equal proportions & no pigment, over and including 20 mm thick screed bed or bedding layer in cm 1:6 etc. complete all as specified and directed.

M&L Machine cut pre polished kota stone slab flooring 20-25mm thick over 20mm thick cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L Granite (of any type) tiles 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specifird and directed over Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes complete all as specified and directed.

M&L Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F 110mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints, laid in trenches or in floors complete all as specified and directed.

S&F 75mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints, laid in trenches or in floors complete all as specified and directed.

S&F 110mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints, fixed in walls complete all as specified and directed.

S&F PVC (SWR) 110mm dia bend of any radius complete all as specified and directed.

S&F PVC (SWR) 75mm dia bend of any radius complete all as specified and directed.

S&F PVC (SWR) 110mm dia double T equal or unequal at Junctions of any radius complete all as specified and directed.

S&F PVC (SWR) 75mm dia double T equal or unequal at Junctions of any radius complete all as specified and directed.

S&F CI floor traps 110mm bore with stainless steel grating including jointing to waste pipe in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F 15mm Bib taps chromium, plated cast copper alloy, fancy type with cruttch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed 15mm bore complete all as specified and directed.

S&F PVC waste pipe 40mm dia for sink, complete all as specified and as directed

S&F in repairs sink with drainage board made up of stainless steel 1mm thick for kitchen or laboratory with plug washers and waste fittings including bedding in CM 1:3 into dwarf wall or cantilever brackets and connecting union to pipe over all size 915mm x 460mm, bowl size 410 x 330 x 160mm etc complete all as specified and as directed.

Taking up or down, 25mm dia bore, GI tubing, medium grade, including cleaning for refixing or removing from site, complete all as specified and as directed

Taking up or down, 20mm dia bore, GI tubing, medium grade, including cleaning for refixing or removing from site, complete all as specified and as directed

Taking up or down, 15mm dia bore, GI tubing, medium grade, including cleaning for refixing or removing from site, complete all as specified and as directed

M&L for 25 mm bore unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe complete all as specified and directed.

M&L for 20 mm bore unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe complete all as specified and directed.

M&L for 15 mm bore unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe complete all as specified and directed.

S&F SS Grating with drain trap of size 300 x 300 x 75mm of complete all as specified and directed and make as approved by GE, complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

Dismantling boarding/Frame work of any description, fixed in any position with nails/screws.

S & F Aluminium anodised (minimum anodisation is 50 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars,standard aluminium grills, with panel inserts of sheet glass, gauze including necessary joining cleats, glazing clips, rubberbeading, Neoprene packing, anodised aluminium snap beading, screws, imax hinges,butt hinges,handles, locking arrangements etc., complete with standard aluminium sections, complete all as specified and as directed (Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately).

S&F 24 Inches(maximum) Telescopic Drawer channels stainless steel Rust free 600mm Ball bearing soundless office Table drawer slides pack of 1 set(2 Pcs) complete all as specified and directed.

Supply only 12mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination and fixed to aluminium frames complete all as specified and as directed.

Supply only 125mm aluminium handles, cast type , anodised complete all as specified and directed.

Supply only 150mm aluminium handles, cast type , anodised complete all as specified and directed.

S&F of 150mm Floor door stoper of aluminium alloy and tounge, anodised, with hard drawn steel string, fixed in door complete all as specified and directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

Supply only 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S&F Stainless steel IMAX hinges for aluminium window shutters complete all as specified and directed.

Supply only aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and as directed

Supply only 5.50mm thick sheet glass, ordinary quality in squares exc 0.50 sq.m in each pane complete all as specified and directed.

Supply only 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F Butt hinges of size 50mm medium weight cold rolled mild steel complete all as specified and directed.

S&F Butt hinges of size 100mm medium weight cold rolled mild steel complete all as specified and directed.

S&F mild steel 40mm dia brass polished cupboard knobs fixed with nut, screw and washer off complete all as specified and directed.

S&F 100 mm long extruded aluminium alloy handles fabricated type anodised complete all as specified and directed.

S7F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

S&FHangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

Supply and fix aluminium composite panel sheet of 3 to 4mm thick as in cupboards, wall cladding & false ceiling fixed on aluminium frame work with plastic strips (Double sided sticker) of suitable size of varying thickness of 10mm to 30mm excluding aluminium frame work applying adhesie over aluminium screws. The joints in panels shall be filled with weather proof sealant, the board shall be stuck with a layer of any colour high intensity reflective grade polymer sticker installed using epoxy adhesive complete all as specified and as directed.

M&L for PCC 1:2:4 type B0 (using 12.5mm graded aggregate) as in levelling course for slope correction of existing RCC roof surfaces including cleaning the roof surfaces and removing existing APP based membrane removing all foreign materials by wire brushes/ brooms/ water jet as specified

M & L for water proofing treatment with the following specifications including taking down existing roof treatment including cement screed/plaster of any description and cleaning with water and scrubbing and disposing off the rubbish outside the premises, complete all as specified and as per manufacturers instructions:- (i) Rendering 10mm thick in CM 1:4 on fair faces of brick or concrete wall surfaces finished smooth and even mixed with water proofing compound @ 3% by weight of cement or as per manufacturers instructions complete all as specified and as directed by Engineer - in -Charge. (Note:- Water proofing compound shall be measured and paid separately) (ii) Apply a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm over a coat of bituminous primer @ 0.3 ltr per sqm. Laying Aquashield membrane weighing 3to 4Kg/sqm, with 100mm over laps both longitudinally and transversally and overlaps shall be sealed by torch, membrane shall be taken to the parapet through fillet and shall be tucked in inside after a height of 300 mm. (iii) Apply one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm over the membrane. (iv) Applying two coats of Aluminium paint on water proofing treatment

Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified .

Demolition of brick work built in cement mortar or lime mortar complete of any description all as specified and directed.

S&F GI frame work for PVC ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm fixed to wall at approx 900mm centre to centre with Gleat and steel expansion fasteners with and including wall section of 0.55 mm thickness having kurled web of 50 mm and flange of 28 mm each with PVC sheet of 1.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre fixed with joining for ‘J’ trim & ‘T’ Section including hanging of 6 mm dia GI (upto 1200 mm length) adjusting level finished to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5 mm dia 40mm long complete all as specified and as directed

M&L 100 mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in sub bases complete all as specified and as directed

M/L 25mm thk PCC 1:2:4 type B-0 using 12.5 mm graded agg as in flooring finished fair and even without using extra cement complete all as specified and as directed

M&L Virified tiles 10 mm thick (square/ rectangular) any shade polished, area of each tiles exceeding 0.42sqm and not exceeding 1.00sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick in Cement mortor 1:4 for laying floor finishes complete all as specified and as directed

M&L Rendering 15mm thick on sides of wall of Brick / Concrete Surfaces in CM (1:6) with level plast including 3 to 5% of water proofing compound finished even & smooth without using extra cement.( Note Waterproofing compound and level plast paid separately) Complete all as specified and directed.

M&L Rendering 10mm thick on concrete surfaces such as sofit of slab, chajja etc in CM (1:3) finished even & smooth without using extra cement complete all as specified and as directed

Materials and labour for Preparation of New plastered surfaces of walls and applying two coats of Plastic emulsion paint over a coat of primer complete all as specified and as directed .

Materials and labour for complete removal of existing treatment on walls and applying one coat of Putty to make the wall surface in plumb line and applying two coats of Plastic emulsion paint over a coat of primer complete all as specified and as directed .

Preparation of old external surfaces of walls, Facias, cornices etc and applying one coat of weather proof anti fungal paint (Apex - ultima) on coat of external wall putty on walls all as per manufacturer instruction and as directed.

M&L for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered or unplastered surfaces of Ceiling complete all as specified and directed.

M & L for Complete removal of existing treatment and preparing old surfaces for applying two coat of oil bound distemper on one coat of primer over a coat of pytty on Ceiling complete all as specified and as directed

S & F Aluminium anodised (minimum anodisation is 15 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangements etc., complete with standard aluminium sections, complete all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately as supplied only).

Supply and fixing factory-made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless-steel screws, joints mitered and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions.

Supply only 4.0mm thick Sheet glass ordinary quality and glazing with oil putty in Square n.exc 0.5sqm in each pane complete all as specified and as directed

M&L for 12 mm thick prelaminated particle board to fixed in repair interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work complete all as specified and as directed

S&F 100 Butt hinges extruded aluminium alloy, anodised. With galvanished mild steel hinge pin , anodised and fixed type B-21 complete all as specified and as directed

S&F 200mm Aluminium anodised barrel tower bolts of extruded sections complete all as specified and as directed

S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 1000litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F inrepairs 15mm Bore Stop Valves / Angular cock with wall flange chrome kubix prime Make: Jaquar Cat Code No KUP-CHR-35053PM.

S&F inrepairs 15mm Bore Stop Valves / Angular cock with wall flange chrome kubix prime Make: Jaquar Cat Code No QQT 7053.

S&F in repairs two way bib tap with wall Flange Make: Jaquar Cat Part NO QQT 7041 screwed down screwed for iron pipe or brass ferule etc complete all as specified and as directed.

S&F in Repair 6mm thickness looking mirror bevelled Edge mounted on bracket as necessary brequirement with chromium plated brass screws and cup washers complete all as specified and directed.

S&F in repairs Gun Metal Gate valves 20 mm dia with iron wheel head screwed both ends for iron pipes complete all as specified and directed.

S&F in repairs Chromium Plated Steel Grating of Jaquar Square Shape Body Shower, For Bathroom, Model Name/Number: Make: Jaquar Cat code no BSH-CHR-1751 complete all as specified and directed.

S & F in Repairs Hand Shower (Health Faucet) with 8mm Dia 1.2 Meter Long Flexible Tube and Wall Hook Make: Jaquar Cat code No ALD-CHR-573 Complete all as specified and directed

Supply and fix vitreous china CASCADE type WC single piece-WC with PP seat Cover, hinges, fixing accessories set, cistern fittings complete of size 640 x 360 x 690 mm , P trap-180mm in approved colour all as specified and directed as per ISI mark. Make : Jaguar cat Part No. SLS-WHT-6851P or equivalent .

S & F in Repairs Bib Cock Make: Jaquar Cat Code no QQT 7073 complete all as specified and directed.

S&F in repair Oval shape vitreous china white thin Rim table top basin of size 500x380x120mm with 32mm waste coupling brass chromium plated suitable for wash hand basins all as specified and directed. Make: Jaquar Cat code No JDS-WHT-25937

S & F in Repairs Bottle trap 32mm dia Make: Jaquar Cat code No ALD 769L250X190 complete all as specified and directed

S&F vitreous China urinal, half stall type complete including waste pipe, flush pipe & providing and fixing plugs, bedding urinal against wall in cement morter 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement etc, and including connection to flushing pipe, Spreader and outgoing pipes fixed in repairs complete all as specified and as directed.

S&F in repairs SS Towel holder all as specified. Make: Jaquar cat code no. AQN7711 complete all as specified and directed.

S & F in Repair corner Glass Shelf with Bracket complete all as specified and directed. Make: Jaquar Cat ACN 1173

S & F in Repair Towel Ring Round complete all as specified and directed. Make: Jaquar Cat AQN 7721

Supply and fix brass CP 15mm dia bore Central hole basin mixer with regular spout without popup waste system with 450mm long braided hoses, 20mm cartridge size also available complete all as specified and as directed. Make: Jaquar cat Part No.FLR-5167NB

S&F in Repair Jaguar Toilet Paper Holder Make: Jaquar Cat Part No AQN 7751 all as specified and directed.

S&F in Repair Jaguar Glass Shelf 550mm long Make: Jaquar Cat Part No AQN 7771 all as specified and directed.

S&F in Repair Jaguar Model No 111Q UC Curved Shapped Urinal Patriation with toughened Glass 10mm thick finish chrome incl fixing with ss Brackets Make: Jaquar Cat Part No JSE CHR 110UC 450X all as specified and directed.

S&F in Repair 20mm thick marble tiles machine cut in skirting/dado/ Cooking Plate form / Table Top laid over cement screed and jointed with grey cement slurry including cutting and polishing of type all as specified and directed.( Note :- Colour/ Shade is finalized by GE)

S&F in repairs PVC flexible connections 15 mm dia 450 mm long with brass checknuts complete all as specified and directed.

Taking down PVC waste ,vent,rain water pipes incl fittings in any position complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor complete all as specified and directed.

S&F 75mm dia outlet PVC (SWR) PVC (SWR) multi floor trap with grating including jointing with solvent cement

S&F PVC (SWR) Gully trap 125/110 mm,seting and incl joining with solvent cement

S&F 110mm PVC (SWR) WC connector bent type setting including Joining with solvent cement

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floors.

S&F PVC (SWR) cowls 100mm dia.

M&L for precast man holes cover slab with 1:2:4 type B1 using 20mm graded stone aggregate set in CM 1:4 incl cost of use and waste of clean sawn wooden form work but excl cost of reinforcement all as specified

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in surface channel / benching incl cost of use and waste of clean sawn wooden form work all as specified

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi-ted/stoped ends etc

M & L for Providing 15mm thick superior quality chemical pressure treated edged glued finger jointed rubber wood boarding tongued grooved fixed over rubber wood frame work with rubber wood runner of size 50mm x 15mm fixed at 1200mm c/c horizontally by secret nailing with brass screws duly fixed to wall including provision of designed rubber wood beading on top and bottom termination of wood boarding and finished with two coats of melamine polish over a coat of honey/natural colour wood filler putty etc, including preparation and applying sand paper and finishing to a glossy/mat finish complete all as specified and as directed. Make : RUBCO or Equivalent

S&F 12mm thick toughened glass in required size crystal polished at the edges and with full etched design approved by GE in different colours fixed with SS brackets of size 50x25mm,100mm long made out of 3mm thick SS sheet at the top and bottom including provision of stainless steel hinges & brackets to connect to SS railings glass to glass, wall to glass connector, magnetic seal, middle seal etc all as directed

M&L for 20mm thick Granite of any type work table rubbed and polished in steps, jambs , pillars, cooking platforms and the like including pointing with white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including Screed bed of coat 20mm thick CM (1:4) complete

Taking down carefully copper/ aluminium point wiring of any type & pattern (Light/Fan/Socket or power) including fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings of any type etc and making good disturbed surfaces of walls/ roof etc, complete all as specified and directed.

Taking down complete main switches/DBs with enclosure and its components of any size and capacity ,etc complete all as specified and directed.

M&L Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including concealed PVC conduit and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable green in colour as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets,fan regulators etc., all as specified and as directed forthe following:- (a) One light/ exhaust fan point controlled by one switch

(b) One fan point controlled by one switch and one regulator

(c) One 3 pin switch socket outlet point 5 amps on same board

(d) One 3 pin switch socket outlet point 5 amps on independent board

(e) One bell point controlled by one switch

(f) One light point controlled by two 2-way switches, with cables 1.5 sqmm size

All as per item No 158.00 above but for 3 pin 15 Amps switch socket combination on independent board with 4 sq mm copper cable and provision of 4 sq mm FRLS PVC insulated stranded copper conductor cable for earth continuity conductor connected to common earth dolly connecting upto fittings complete all as specified and as directed.

S&F modular type 6A one way SP switch 1 module complete all as specified and directed.

S&F modular type 2/3 pin combined shuttered type 6 Amps socket 2 module complete all as specified and directed.

S&F modular type 2/3 pin combined shuttered typr 16 Amps socket 2 module complete all as specified and directed.

S&F modular type 16 A one way SP switch 1 module complete all as specified and directed.

S&F modular type 120W step fan regulator of 2 module size complete all as specified and directed.

S & F Modular cover plate 6 modules

S & F Modular cover plate 4 modules

S & F Modular cover plate 3 modules

Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specfified and as directed.

S & F Single pole and neutral metal enclosure with 2 pin and earth plug and socket and top plug complete with 20 Amps MCB SP , 240 Volt all as specified and as directed

Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor flashner for fixing of fan on ceiling complete all as specified and as directed.

Supply and fix aluminium housing LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as directed.

Supply and fix exhaust fan steel body suitable for on working of AC 230 V ,50 Hz 300 mm sweep 1400 RPM,with heavy duty motor ,incl louvers complete all as specified

Taking down old unserviceable exhaust fan 300 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site with new clamps, nuts, washers, safety wire of size not less than 1.00mm & bolts including cotter pin for complete all as directed.

Taking down old unserviceable ceiling fan 1200 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site with new clamps, nuts, washers, safety wire of size not less than 1.00mm & bolts including cotter pin for complete all as directed.

Supply and fix in repair sheet metal enclosure Loadline distribution vertical DB, MCCB as incomer 4 ways 415 volts, with 200 amps rated bus bar double door suitable for mounting MCCB 100 A TPN as incomer and MCBs as outgoing, Triple pole as incoming complete all as specified and directed including taking down old MCB DBs complete.Thye Rate shall be included the incomer MCCB TPN of 100 Amps Note-: Incoming & outgoing connections from the DB shall be provided with proper lugs/ thimbles etc

Supply and fix switch piano flush button single pole oneway 5 amp complete all as specified and as directed.

Supply and fix switch piano flush button single pole two way 5 amp complete all as specified and as directed.

Supply and fix switch socket combination 3 & 2 pin (multi pin) 5 amp flush type complete all as specified and as directed.

Supply and fix socket outlet multipurpose 3 & 2 pin 5 amp flush type complete all as specified and as directed.

Supply and fix switch socket outlet multipurpose 3 pin 15 and 5 amp controlled by one switch, flush type complete all as specified and as directed.

Supply and fix lamp holder(angle type) PVC body with back plate suitable for batten fittings, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 10 w LED bulk head fitting prewired upto connection block and connecting with three core PVC copper flexible cable of size 1.5 Sq.mm from ceiling rose to connector block, including taking down old unserviceable fitting of any wattage, complete all as specified and directed by Engineer-in-Charge

Supply and fix bell push single phase, 240 Volts, 50 Hz, complete all as specified and as directed by Engineer-In-Charge.

Supply and fix bell Ding Dong 240 Volts 50 Hz complete all as specified and directed by Engr-in-Charge.

Supply and fix fan speed regulator, electronic suitable socket type for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge

S&F 25 W New genration energy saving & envoirmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs as light and electronic driver complete with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed.

M & L in repairs for sub main wiring complete with two runs of 6 Sqmm FRLS single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor (ISI Marked) drawn through and including PVC Casing and caping and all accessories fixed to wall/ roofs/ floors etc with one run of 6 sqmm FRLS single core multistranded copper conductor as earth continuity conductor, including dismantling unserviceable sub main wiring including accessories,complete all as specified and as directed by Engineer-in-Charge. Note : (1) Two runs of cable one run of casing caping & one run of earth continuity conductor shall be measured as one running metre.

Supply & Lay XLPE insulated, heavy duty 1100 volt grade electric armoured LT UG cable with aluminium conductor of size 25 Sqmm 3.5 Core in trenches/along the wall/including making all connections, saddles, spacers including scaffolding if any required for saddling the cable in walls of building of height up to 25 meter, complete with aluminium lugs as required at site and as directed.

Supply and fix in repair metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs complete all as as specified and as directed by Engineer-in-Charge

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed.

Supply and fix MCB SPN 240 volts, 5 to 32 Amps, all as specified and as directed.

M & L in repairs for sub main wiring complete with two runs of 4 Sqmm FRLS single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor (ISI Marked) drawn through and including PVC Conduit and all accessories fixed to wall/ roofs/ floors etc with one run of 4 sqmm FRLS single core multistranded copper conductor as earth continuity conductor, including dismantling unserviceable sub main wiring including accessories,complete all as specified and as directed by Engineer-in-Charge. Note : (1) Two runs of cable one run of coduit & one run of earth continuity conductor shall be measured as one running metre.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 10 sq mm.

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed.

S&F tube light grade galvanised with all fittings laid in trenches of following size. (a) 50 mm bore.

Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge.

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

M&L for cutting existing 40mm GI line and making branch connection of 25 mm dia GI line including fittings required for connection complete all as specified and directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specifed and directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out (a) Soft/loose Soil

Chandra Construction Enterprises

Tropical Refrigeration

SK CONSTRUCTION

SKY GROUP

DHAKSHNA MOORTHY AND SON

M/s Karbhagam Sales Agency

KRISHNA TRADING COMPANY